7 Best Aftermarket Table Saw Fence. Universal table saw fence

Table Saw Accessories

When cutting mitered angles with your table saw you always want to make sure that have enough support of your stock when feeding it through the blade. The table saw blade is rotating toward you at a high rate of speed and if your workpiece moves to the side, the result can be scary and downright dangerous. With the help of a miter gauge and with our Aluminum Miter Fence secured to it, you will have full support all the way up to the blade on most of your miter angle cuts. See more product details

×

Universal Miter Gauge Fence

When cutting mitered angles with your table saw you always want to make sure that have enough support of your stock when feeding it through the blade. The table saw blade is rotating toward you at a high rate of speed and if your workpiece moves to the side, the result can be scary and downright dangerous. With the help of a miter gauge and with our Aluminum Miter Fence secured to it, you will have full support all the way up to the blade on most of your miter angle cuts.

The Aluminum Miter Fence has been cut at 45 degrees on both ends of the fence. Doing this allows you to get as close to the blade as possible so your workpiece is fully supported throughout the cutting process. Straight cut or 90 degree cut fences have a large gap between the fence and the blade because it can not get as close with the straight cut ends on the fence.

Cross Cut Angles on Your Table Saw

While a simple miter gauge works pretty well when it comes to cutting angles on your table saw, the miter gauge by itself does not offer much support near the blade when making cuts. In steps the versatile and easy to install Fulton Aluminum Miter Fence!

The Perfect Add-On Accessory for Most Miter Gauges

• Works with most any brand of miter gauge
• Even works with old school style miter gauges (some minor miter gauge modification may be required)
• 45 Degree cut fence ends offer maximum support when cross cutting on your table saw
• Includes a sturdy aluminum flip stop for repetitive length cuts so you don’t have to keep measuring after every cut!
• Includes a left reading and right reading sticky back tape for left or right tilt saws

Designed to Be Versatile

The Fulton Aluminum Miter Fence has been designed so it will fit most major brands of miter gauges. From the Precision Kreg Fence to the high end INCRA miter gauge systems to most every standard gauge in between, the Fulton Aluminum Miter Fence will likely fit. The mounting slot on the back of the gauge can be used with standard height gauges and the fence can also be flipped upside down so the slot will accommodate lower profiled miter gauges!

Does it Fit Your Old Delta Gauge.

The short answer is, why yes, yes it does! The longer, but not difficult to understand answer is that the fence should fit most older gauges with the holes that are already in the miter gauge head. If there aren’t any holes or they just don’t line up, we have provided instructions on how to use a block of wood to remedy this or how to modify the miter gauge itself to attach the Fulton Aluminum Fence.

Max Support Every Time!

Many miter gauge fences have flat or 90 degree ends. While this style of fence kind of works, it is not the optimal way of fully supporting your stock piece through the cutting process. The Fulton Aluminum Miter Fence features 45 degree cut ends which allows you to achieve full support all the way up to the blade. This helps prevent pinching or binding while cutting which ultimately helps prevent dangerous kickbacks.

Make your cut and accurately repeat.

When you need to cut multiple pieces to length, nothing is more frustrating than having to move your piece into position, measure and adjust your piece again until you hit your mark. With the Fulton Flip Stop, repeititve cuts on your table saw is super easy and super quick. Simply slide the stop into position, lock it in place, lower the stop and slide your stock piece up against the stop. Now your ready to make precise length cuts each and every time!

Left or Right? In this case, there’s no wrong answer.

We have included a left reading tape and a right reading tape. The reason we have done this is simply for the fact that some prefer one to the other and some saws dictate which one you will use. Also keep in mind that you can always flip the tape upside down in relation to the fence so that you can read the tape when looking down on the fence from above.

Many times when we make miter cuts on our table saw, we need 2 or more pieces that are the exactly same length. While using the included measuring tapes that are included are pretty good at this, we have also included a handy flip stop that locks into any location along the length of the fence. This allows you to make repetitive length cuts without worrying if the pieces will end up the same. The flip stop can can simply be flipped it up and out of your way when not in use.

The Fulton Aluminum Miter Fence is made from one, solid piece of extruded aluminum and has the exact same size track on the top of the fence as there is on the bottom. On the back, there is an offset track for mounting the fence to a miter gauge.

The fence can be mounted to low profile miter gauges or standard profile miter gauges simply by flipping the fence over to accommodate your miter gauge. This fence will fit most available after market and factory table saw miter gauges, however some modification may be required. Full color installation instructions are included.

• Works with most any brand of miter gauge
• Even works with old school style miter gauges (some minor miter gauge modification may be required)
• 45 Degree cut fence ends offer maximum support when cross cutting on your table saw
• Includes a sturdy aluminum flip stop for repetitive length cuts so you don’t have to keep measuring after every cut!
• Includes a left reading and right reading sticky back tape for left or right tilt saws

California Residents: WARNING: Cancer and Reproductive Harm. www.P65Warnings.ca.gov.

Miter Extension Fence

• When used with miter gauge you may need to make minor adjustment to align bolts with the channel on miter fence.
• When used with miter saws you may need drill into the existing fence to align to channel on the miter fence.
• When used with the drill press you will need Item# 1097. 24″ premilled “L” fence (sold Seperately) or make your own to connect the fence to the drill presstable

The 22” Miter Extension Fence was designed for the table saw miter gauge.It will improve work support close to the blade and will work on the left side or right side of your saw.The adjustable extruded aluminum fence increases the face of your miter gauge and has a built in extension bar to increase the stop capacity to 36”.

The 48” Miter-T-Fence is designed for your miter saw with a built in extension capacity of 86”. This fence can be used in conjunction with the 22” or anoter 48″ fence to give your miter saw a fence for both sides for the ultimate fence system your shop will ever know.

The 22” or the 48″ Miter Extension Fence can be added to your Miter saw and/or your drill press for longer more durable fence system. It’s perfect for repetitive cuts and drilling holes with the included stop block. The stop block will slide back and forth along the top channel of the miter fence. The fence can be easily taken on and off any of the tools to switch back and forth between tools.

Both fences include a stop block for the repetitive cuts and appropriate knobs and bolts for easy mounting on and off your various tools.

California Residents: WARNING: Cancer and Reproductive Harm. www.P65Warnings.ca.gov.

Best Aftermarket Table Saw Fence

This post may contains affiliate links. If you click and buy we may make a commission, at no additional charge to you. Please see our disclosure policy for more details.

If you are a woodworking enthusiast, you understand the importance of precise cuts. The table saw is a tool that is commonly used for cutting projects. But achieving a superior precision level requires years of practice.

An aftermarket table saw fence is a woodworking tool that can help you get accurate cuts safely, every time. The table saw fence would hold the material you are working on in place. You can then cut the material in the desired shape.

Our Top Recommendation for Aftermarket Table Saw Fence!

The Shop Fox W1716 Aluma-Classic Fence is a highly durable aftermarket table saw fence that specializes in precision cuts. The fence has standard 57-inch rails, with a 30-inch maximum rip capacity.

We earn a commission if you make a purchase, at no additional cost to you

These fences differ in terms of material, size, compatibility with table saws, and cost. If you are looking for a table saw fence, the article will take you through the top quality products available in the marketplace.

What is the Best Aftermarket Table Saw Fence?

The answer to this question differs from one person to another. Factors like the type of projects and table saw you use affect the table saw fence model you should buy.

For example, the fence should be compatible with the model and hole pattern of the table saw. Both tools should align in terms of measurement. If the fence is too small for the table saw, it will negatively impact stability. If the fence is larger, the cutting process could end up being a hassle for you.

Thus, it is essential to pick a table saw fence that best suits your requirement.

For your convenience, the below table contains distinguishing features of table saw fences that will suit your varying woodworking needs.

IMAGEPRODUCTFEATURESPRICE

Best Aftermarket Table Saw Fences

Buying a table saw fence is a long-term investment. Thus, you should take your time researching options before clicking on the ‘Add to Cart’ button.

Here is a list of top table saw fences to help you decide which tool will become your trusted partner.

Shop Fox W1716 Aluma-Classic Fence

This fence model from Shop Fox comes with standard 57-inch rails. The tool provides optimal precision with its right-angle design and wide-spaced adjustment points

The fence provides a 30-inch rip to the right of the blade. However, the rip capacity of the model limits the fence used to small projects.

The steel and aluminum body of the fence makes it a sturdy and durable choice. In addition, the construction materials used help reduce the overall weight of the tool.

The fence comes equipped with features like an adjustable magnified cursor, a self-adhesive measuring tape, a single locking cam action lever, a torsion box design, and adjustable fence wear pads.

This model can indeed fit about any table saw you own. But you will have to drill holes on the rails for that perfect fit. So, take your time setting up the tool.

Magnified Cursor

The combination of a self-adhesive measuring tape and the magnified cursor makes reading measurements easier. The tape comes in a bright yellow color with the numbers in black. You will find graduations in both metric and SAE scales.

This well-thought detail will help you position the fence accurately.

Strong Locking Lever

The single locking cam action lever provides solid support. You can adjust the lock easily with one hand.

Once you position the fence as per your requirement, the locking mechanism ensures no movement. In addition, the torsion box design ensures no displacement when you are guiding the wood.

Pros and Cons

• Highly durable
• The right-angle design provides optimal precision
• Heavy-duty locking lever for support
• Adjustable magnified cursor improves visibility
• Can be used with most table saws

Shop Fox W2005 Classic Fence

The W2005 Classic Fence is another quality and model from Shop Fox. It has a classic design that offers high functionality. If you aim to have a robust and precise aftermarket table saw fence at a budget-friendly price, this is the model for you.

It comes with standard rails providing a 25-inch rip capacity to the right of the blade. The wide-angle design of the fence ensures you have ample support and cut accurately.

This model is easy to install and use. If you are new to woodworking, seek help with installation. It is compatible with most brands of table saws. Another unique feature of the fence is the lift-off design. You can remove the fence when not required and also reinstall it with the same ease as needed.

The simple cam lever ensures the fence stays locked in position. You can easily fine-tune the tool with the adjustable slider pads. It also comes with replaceable side panels made from HDPE plastic. The materials offer high resistance to wear and tear caused due to repetitive friction.

With the rip capacity limited to 25 inches, the fence will work better with smaller table saws. You can look into the optional long rails that provide 54-inch rip capacity.

Easy to Use

The W2005 Classic Fence comes with a single locking cam action lever, using which you can make adjustments one-handedly.

The HDPE material used for side panels and the torsion box design ensure guiding wood around the tool is effortless.

The magnified cursor and self-adhesive scale make reading measurements easier. Additionally, the cursor can be mounted on any side of the fence.

Lift-Off Design

You can lift the fence off the rails anywhere along the length. This is a convenient feature when making cross cuts or using different jigs and fixtures.

Pros and Cons

• Works well with most table saws
• Increased durability with powder coated paint for fence body
• Provides tough abrasion resistance
• A magnified cursor for better readability

Shop Fox W1410 Fence

This basic aftermarket table saw fence from Shop Fox provides professional accuracy to your projects. The fence will fit most of the major 27-inch table saw brands. The model is one of the low-cost fences that are compatible with older versions of the saws as well.

Depending on the table saw model, you will have to drill holes to install the fence. Follow the instructions that come with the fence carefully, and you are good to go. The ball bearing guides enable the tool to move effortlessly. The locks on both ends make using this fence a breeze.

The locking lever allows for repeatable cuts without any fence movement. Positioning knobs on both sides ensure you can use the fence seamlessly, regardless of one being right or left-handed.

Accurate Results with Minimal Effort

The locking system on both ends makes it easy to use with a range of table saws. The fine positioning knobs on both sides make cutting and trimming hassle-free tasks. With the ball-bearing guides, you can move the fence smoothly. A slight push on your end is all you need to get the fence gliding.

Pros and Cons

• Ball bearings offer unrestricted movement of the fence on the table saw
• It fits major table saw brands
• Locks on both ends
• Fine positioning knobs available on both sides

Wixey WR700 Saw Fence Digital Readout

Absolute precision is the reason why users prefer this model from Wixey. The unit has a total length of 60-inches. In addition, it uses ‘Precision Fraction Technology,’ patent-pending, which enables fractions to be displayed with an accuracy of up to 0.002 inches per foot.

The kit comes with all the necessary hardware required for mounting, such as brackets, self-threading screws, and drill bits. It works well with most of the round rail and rectangular rail fences.

The Wixey WR700 saw fence’s digital readout operates on 2 AAA batteries. Its power-packed digital readouts make taking measurements and cutting with precision an easy task.

The large readout displays different measurements like inches with fractions and millimeters.

You can use absolute or incremental measuring mode when working on a project. Once updated, the machine will retain the settings even when turned off. If you need to perform repetitive tasks, this feature comes in handy.

Easy to Setup and Use

The readout can be easily attached to your existing table saw fence. The kit comes with a detailed set of instructions depending on the type of fence. The hardware necessary to mount the unit to the bottom of the fence is also included in the kit.

The display readout is large and easy to read. In addition, fence removal and replacement have been simplified thanks to the magnetic attachment method.

Make Repetitive Cuts with Precision

You can calibrate the unit on either side of the blade. The process is as simple as moving the fence towards the blade while holding the calibrate button. In addition, it comes with a unique magnet system that allows you to remove the fence while the readout stays calibrated at all times.

Users have found the unit to retain accuracy even when the fence has moved back and forth throughout the day. And also, when you remove the fence, put it back and make the same cut.

Pros and Cons

• Precise measurements
• A rip capacity of 60 inches
• Digital readout can be attached to either side of the fence
• Preserve battery with auto shut off function

Carter Magfence II Universal Magnetic Fence

If you are new to the world of woodworking, here is an aftermarket table saw fence that is best suited for you. Most traditional fences require expertise in drilling holes during installation. This fence presents an alternative with its use of powerful magnets.

Instead of locking systems, the fence holds the board in place with the help of magnets. The tool truly lives up to its name of being a universal fence. The fence can fit on most steel and cast iron tables.

The fence’s dimensions are 16″ in length, 3-1/2″ in height, and multiple T-slots. It is made from aluminum, which means the product is durable. The model comes with two magnets that you can switch to make quick adjustments per your need.

Universal Fit

You can use the fence on different metal tables regardless of its size. You do not need any brackets or mounts for installation. You can simply attach the fence to the surface and let the magnets take over.

You can even remove the fence with the same ease. over, it can be used with various other tools like a bandsaw, spindle sander, and drill press, among others.

Beginner-Friendly

Working with other types of table saw fences requires some level of expertise. In addition, the installation process can be tricky. If not followed correctly, you will be left with a tool that is not optimized for precision.

You can leave these worries behind with Carter Magfence II Universal Magnetic Fence. Instead, you can attach the fence and perform tasks like cutting, positioning, drilling, or aligning easily.

Pros and Cons

• It fits easily on most metal surfaces
• Attach, adjust and remove the fence with ease
• Great product for beginners
• It can be used with multiple types of equipment

Fulton Precision Miter Guage

The Fulton Precision Miter Gauge is an economical fence option you should consider. The Fulton Miter Gauge, Aluminum Miter Fence, and Aluminum Flip Stop are three items that work together to fulfill your table saw needs.

One of the distinguishing features of the product is the 45° fence end that provides maximum workpiece support and holds it in place. As a result, you can position the fence closer to the blade. And also have better control of the workpiece.

The wood binding issue that you might have experienced with a standard 90° fence end is resolved with the change in angle. You can now get much more precise and cleaner cuts.

The head is made from 200″ thick solid aluminum, which can be adjusted and has 13 positive stop holes. The aluminum head is fitted onto an 18″ solid steel miter bar. The precision miter gauge is made from a single piece of extruded aluminum. The quality materials used for construction ensure the durability of the product.

Aluminum Flip Stop for Repetitive Cuts

Using a standard miter gauge for repetitive cuts can be a hassle. You do not want to keep adjusting the gauge and the fence while working. The product resolves this issue with a convenient aluminum flip stop.

Slide the flip stop to the desired position, lock it in and make your cuts. You can either remove the fence or pull the stop upwards when not in need.

Easy Adjustment

The miter gauge comes equipped with 13 positive stops. You can loosen the handle by turning it counterclockwise. Next, pull the pin lock up and adjust the miter gauge to the required angle. Once positioned, release the pin lock; it will fall back into place. Lastly, secure the handle by turning it clockwise.

The positive stops do not limit your angle range. You can work on any angle of your choice by pulling the pin lock upwards and turning it so it does not interfere with any of the positive stop holes.

Pros and Cons

• Crosscut angles with ease and precision
• 45° fence end prevents binding and provides cleaner cuts
• Positive stops included at the most common angles woodworkers use
• Steel miter bars with removable disc and adjustable spring-loaded plungers for a better fit

Powertec BS900RF Rip Fence

The Powertec aftermarket table saw fence model is sturdy and durable. It is designed to work with 300mm or 11-13/16″ tables. The fence can be adjusted from 11-3/8″ to 12″ by turning the lock lever. Turn clockwise to shorten the length and turn counterclockwise to increase the length. In addition, you can produce straight parallel cuts with this fence.

The product is made from industrial-grade aluminum. This means the product will last for a long time. So it will provide good value for the money you spend. The fence snuggly fits into a square for safety and performance reasons.

Another advantage of this Powertec model is that it comes fully assembled. You can use the fence right out of its package. You may require minor adjustments. So if you are new to woodworking, start with this no-fuss, easy-to-use fence.

Maximum Support

The Powertec fence is designed to fit firm and square to the table. This angle provides optimal support. The model also comes with a handy cam-lever, using which you can adjust and secure the placement lock.

Be careful when setting your fence up. You can adjust the clamp according to your table. But if you feel resistance when pushing the lever down, loosen the clamp. If you try to force the lever down, it might break the cam.

Pros and Cons

• Extruded aluminum construction – is durable
• It makes straight parallel cuts
• Effective cam-lever action
• Firm clamp design supporting ripping action

Summary

A table saw fence is a value-adding tool that should be part of your woodworking workshop. It helps secure your material in place and provides support. over, you can perform actions like cutting and drilling safely. You can make professional-grade precise cuts with them.

Measure your work table and types of table saws. See if the fence is compatible with the equipment you already own. Understand your requirements before you go buying a fence.

We hope the above list of aftermarket table saw fences help you arrive at a decision.

Best table saw fence in 2023

For both amateur and pro woodworkers, the table saw system is the central piece in any woodworking shop. However, some models of the tables are just not suited for safe and accurate work.

Veering off course when cutting wood is a really unpleasant experience. That’s why accuracy is the number one priority when it comes to choosing a table saw fence.

A suitable table saw fence allows you to make perfect cuts and keeps you safe while working. You don’t want to have a fence that would require some second-guessing and extra measuring from you. It should also be a sturdy and steady one.

In this article, we will cover some basic factors you should consider when choosing the best table saw fence in 2023. You will also see plenty of recommendations for different models you might select.

• 1 How to find the best table saw fence in 2023

• 1.1 Manual and electric fences
• 1.2 Types of table saw fences
• 1.3 Table saw size
• 1.4 Table saw fence weight
• 1.5 Compatibility
• 1.6 Rip size
• 1.7 Ease of install
• 1.8 Ease of use
• 1.9 Price
• 1.10 Common advantages of a table saw fence

• 2.1 1. Vega U26 Table Saw Fence (best overall)
• 2.2 2. Carter Magfence II Universal Magnetic Fence (best for beginners)
• 2.3 3. Shop Fox W1410 Fence (one of the best by price)
• 2.4 4. Shop Fox W2005 Classic fence with standard rails
• 2.5 5. Delta 36-T30T3 30-Inch Fence System
• 2.6 6. Vega U50 Table Saw Fence System
• 2.7 7. Wixey WR700 1500mm/60″ Digital saw fence readout
• 2.8 8. DeWALT DW745 Table saw replacement fence assembly
• 2.9 9. Delta BC50T2 Table Saw fence (Premium Choice)

How to find the best table saw fence in 2023

First, let’s look at these key factors below before considering the different table saw fence market options.

Manual and electric fences

There are manual and automatic table saw fences on the market.

If you cut large quantities of wood every day (e.g., if you’re executing orders regularly), then electric models are going to help you a lot. They can do the heavy lifting for you, so you save your stamina in order to cut more. Electric fences also allow you to cut more accurately because you can switch between measurements quickly.

Manual saw fences are generally cheaper, though. Many woodworkers choose manuals because they enjoy pushing wood along the blade with their own hands. It does give some satisfaction.

Manual saw fences are generally cheaper though. Many woodworkers choose manuals because they enjoy pushing wood along the blade with their own hands. It does give some satisfaction.

It’s up to you to decide which type of fence will suit your needs best.

Types of table saw fences

There are many types of table saw fences out there. But these four are the most common ones:

The Sliding Fence. Sliding fences are usually found on sliding table saws. As the name suggests, this fence slides back and forth and lets your miter gauge make precise cuts on the right side of the blade. It can also be put parallel to the blade to form a lower profile. It is really useful when cutting thin boards.

The T-Square Fence. This type of fence has a three-point locking system which allows you to keep your position and stability even when working with heavy boards.

Micro-adjusters. These fences offer you the ability to adjust your fence by turning a knob. You don’t have to manually adjust your fence with these.

Digital Readouts. Digital readout fences are relatively new aftermarket tools that allow you to make the most accurate measurements.

Table saw size

Table saws have different dimensions, and your saw fence system is supposed to match the saw you have.

Some systems are more versatile than others and can fit on most saws. Other systems have their limitations and are designed to fit a particular saw size.

Some saws will only work on 27-inch tables, others will work on fences much longer (42-inch). One of the most common lengths is 36-inch. The size of the saw and the fence system will depend on the scope of the projects you’re planning to work on.

If you’re left-handed, you should definitely pay attention to the measurements of both sides of the blade. Many times there is enough space on the right side and not enough on the left, which can pose a problem.

Table saw fence weight

The right weight is also important when choosing the best table saw fence.

An average table saw can take dozens of pounds of weight, but it is not necessary. If your table saw fence is too heavy, it can put lots of excessive pressure on the table and even cause the surface to deform.

On the other hand, if the fence is too light, it can break with just a little push. You also will not be able to clamp heavy boards with it.

So, the optimal weight range for fence systems is between 30 to 50 pounds.

This range allows you to avoid damaging your table saw or fragile accessories like a miter gauge and keep your heavy boards in place.

Compatibility

If your table saw and fence come in one set together, then they will fit each other perfectly.

But if you got your existing table saw separately and you want to buy a suitable fence on your own, then you should take measurements. You should know the exact length of your table as well as the model and hole pattern.

This way you will make sure that you buy the right fence system.

Rip size

The rip fence capacity of your fence system will depend on the size of your projects. If you’re planning to cut large logs and boards, then don’t hesitate and buy a fence with a large rip size.

This way you won’t have to spend extra hundreds of dollars on a new fence system in several years!

Also, if you need to handle huge boards, you can pick a fence with extended rails which enhances the rip fence capacity.

Ease of install

• Whether it is a set with a table saw, fence, or just one aftermarket table saw;
• Whether the table saw and fence are made by the same brand;
• Whether the table saw fence manufacturer made their product ‘universal’ or not.

Again, if you’re buying a set, then there should be no problems installing it. The table saw and the fence will be ready for use in just half an hour.

If the aftermarket table saw fence and the table saw were both made by the same brand, you will have an easier time installing them as well.

Ease of use

When choosing a fence, pay attention to the controls: you need to have easy access to a single-handed cam or lever. Front-locking fences allow you to operate the controls with only one hand.

Smooth-rolling is also important. Using the fence becomes more difficult if you have to do extensive shimming or lubricating in order to make the movements smooth enough.

Price

Beginner and replacement fences might be cheaper than 100, but a good and reliable table saw fence will cost you about 100-400.

Replacement table saw fences are short-term stand-ins, that’s why they are relatively cheap.

Common advantages of a table saw fence

Improved accuracy: a fence locks the wood piece in place so you can achieve accurate cuts. It also means you can create more delicate pieces;

Efficiency: by making more precise cuts you have fewer failed wood pieces. This means you spend less time and energy while perfecting your pieces.

The list of the best 9 table saw fences

Here is a collection from which you can pick your best table saw fence!

Vega U26 Table Saw Fence (best overall)

This fence is probably the most sought-after table saw fence on the market, and that is for a good reason.

It is versatile and can be used with various table saws. The Vega system includes front and rear standard rails for mounting the fence. The fence bar is 36 inches long, which is a good size for both hobbyists and professional woodworkers.

The fence gives you plenty of space to make rips of different sizes – the rip size is 26 inches to the right and 8 inches to the left. However, the U26 is not meant for heavy projects.

The weight is over 30 pounds, but that is due to the fence parts being made of solid steel. The fence can be adjusted to a wide range of saws. But you might have to drill some extra mounting holes in order to install it properly on your exact model.

The U26 also has a fine-adjust for dialing measurements. The fence is really sturdy and doesn’t budge when locked into place. You won’t have to worry about distance changes or other shallow things.

• Durability
• Stability
• Versatility: the fence is compatible with most table saws
• Ease of setup: can be assembled within 20 minutes
• Smooth rolling to and fro
• Fine-adjust knobs for easy operation included

Carter Magfence II Universal Magnetic Fence (best for beginners)

If you’re just getting started in woodworking, this table saw fence will be perfect for you.

Most other fences use clamps, locking systems, and other devices for holding the boards in place. The Carter Magfence has two powerful magnets for this purpose.

These magnets are suited to almost any metal surface, which makes it easier for newbies.

You don’t even have to drill extra holes for installation! You just need to place the fence on your table, and the magnets will hold it in place.

• Unique table saw fence that is installed using magnets
• Ease of use for beginners
• Versatility: the fence can fit any table saw with a metal surface
• versatility: both magnets are interchangeable
• Saves lots of time and stress

Shop Fox W1410 Fence (one of the best by price)

This fence is well-suited to smaller projects.

This Shop Fox model has ball-bearing guides that enable really smooth rolling motion. The fine-positioning knobs on both sides allow you to dial in the distance no matter which side your wood piece is mounted on. The handle clamps are tight enough to hold the boards nicely.

The rip fence capacity is 25 inches, which is enough for most cuts. The fence can fit table saws of up to 27 inches, and it’s not going to work for the larger table saws.

The Shop Fox fence has a pretty reasonable price too – it is lower than those of the competitors. But it does not mean that it feels cheap – it is one of the best table saw fences at such a price.

• Affordable price
• Durability
• Smooth-rolling ball-bearing guides
• Fine-positioning knobs on both sides for higher precision
• Still suited to more complex projects, e.g. furniture crafting
• Ease of setup

Shop Fox W2005 Classic fence with standard rails

The Shop Fox W2005 Classic fence comes with standard rails as an upgrade. It is more pricey than the previous saw fence by Shop Fox, but you get an enhanced version for that price.

TABLE SAW FENCE UPGRADE

The fence includes a single-locking cam action lever which gives you the possibility to securely lock rips using only one hand. Accurate cuts for your complex designs are guaranteed.

The fence is universal so you can use it with most table saws.

The fence is 42 inches, with a maximum rip capacity of 25 inches to the right. It is sufficient for most small- and medium-scale projects. You might have to drill some extra holes in order to install it.

Customers often note the awful packaging of this Shop Fox heavy unit. It is shipped in Styrofoam which usually gets destroyed by the time the package is delivered, so the fence might be damaged.

• Durability
• Accuracy Stability: the wide right angle design enhances them
• Secure locking system: you can lock rips securely with only one hand
• Versatility: the fence fits most table saws
• Smooth and accurate glide
• Micro-adjustments are available

Delta 36-T30T3 30-Inch Fence System

The Delta 36-T30T3 fence system has a three-point locking mechanism with twin hairline pointers which offers accuracy within 1/64 of an inch.

The fence provides stability for your projects. It is achieved by the hook mechanism over the rear rails and the secure clamping points at the front tube. They also allow you to add additional attachments.

The fence movement is pretty smooth. It is also pretty secure and you will see no budging even after you rip lots of boards.

The main disadvantage of the saw fence is that it fits on 27 inch table saws only. The system can be used on either side of the blade. You will probably need to drill some holes for mounting it.

• Durability
• Accuracy Stability: T-Square locking system with twin hairlines
• Easy gliding: smooth surface makes it possible
• The fence can be used on either side of the saw
• No wobbling: the front tube clamps and rear holds ensure that
• The company offers two years of warranty

Vega U50 Table Saw Fence System

This is a great solution for experienced woodworkers working on large projects.

This Vega Pro unit is meant to fit into table hole patterns of brands like Powermatic 66, Contractor Saws, Delta Unisaw, and Sears 10-inch saws. If your table saw comes from one of these brands, then the setup will be way easier and faster.

The Vega Pro table saw fence has a fence bar of 36 inches and a rip capacity of 50 inches. This includes the rip capacity of 50 inches to the right and 8 inches to the left. The fence also has guiding rails which are supported by brackets for more stability.

• Large rip fence capacity: ideal for heavy-duty projects
• The fence comes with micro-adjustments and auxiliary table support
• Full adjustments for table saw fence mounting are available
• Ease of setup: installed on a lot of table saws without drilling holes
• The company offers a 2-year warranty

Wixey WR700 1500mm/60″ Digital saw fence readout

The Wixey table saw fence is even larger than the Vega Pro – it’s 60 inches long! It is made of sturdy aluminum and can be installed on most rails. This is made possible by the universal mounting bracket.

• Exceptional accuracy: digital read-out allows you to measure fences digitally
• High-grade display: includes a magnified cursor for movement
• The battery life is 2 years
• Large rip fence capacity of 60″
• Calibration is possible on both sides

DeWALT DW745 Table saw replacement fence assembly

If you already own a 10-inch DeWALT table saw, this saw fence will act perfectly as a replacement.

The replacement saw fence is made of aluminum and weighs just two pounds. The rip capacity of this unit is 20 inches. You can quickly install it into your DeWALT table until you find your next long-term table saw fence. Despite its low price, the DW745 allows you to make precise cuts and is pretty durable.

Delta BC50T2 Table Saw fence (Premium Choice)

This is also one of the larger table saw fences for a high price. If you need maximum rip capacity and don’t care how much it will cost, then this option is for you.

The rail system is 50 inches long – that includes a right side rip of 34 inches and a left side rip of 16 inches.

The high-quality Biesemeyer fence has rugged steel construction and a three-point locking system we have talked about before, which all make a reliable fence.

Conclusion

Now you know the factors and details which you need to pay attention to when looking for good fence systems.

You also have plenty of options to choose from. Overall, experts usually choose the Vega U26 saw fence. It is one of the best fence models out there indeed.

One of the best fences by price is the Shop Fox W1410. It does not feel cheap at all – it has smooth-rolling bearings, fine positioning knobs, and other features that make your rips straight and precise. There’s also an alternative Shop Fox fence – the Shop Fox W2005 model.

If you’re not bothered by the price, you can consider the Delta Power Equipment Corporation BC50T2 – a premium unit with many advantages. Large rip capacity, multiple mounting options, and versatility totally justify the cost.

We hope you found this article helpful and got some new ideas from it!

Are Table Saw Fences Universal?

As anyone familiar with woodworking knows, a woodshop is not complete unless it includes a table saw. Table saws are capable of making long and incredibly accurate cuts when used in conjunction with a fence. But this leads us to the question, are table saw fences universal? Table saw fences are not universal. Although they may all appear similar, different companies tend to design them with slight variances, making them incompatible with certain saws. Always check your particular saw’s requirements to determine if a specific fence can be accommodated. This article will first provide an overview of how table saws work, what they are used for, and the different types of saws that may be substituted. Next, we will explore the table saw fences in particular: mainly how they operate and their utility. Lastly, we will briefly touch on safety tips to keep in mind whenever using power saws. A good saw is usually the centerpiece of a workshop. We have a great discussion on this topic in the video below on YouTube. You can watch our past workshops on YouTube here(Link to Cucamonga Woodworking)

How Table Saws Work

As the name implies, table saws resemble a table in that they have four legs and a flat top. In addition to this, table saws feature a circular blade, half of which protrudes out of the center of the table’s top. To use a table saw, the blade must be in the on position allowing it to spin rapidly, and the wood or item you intend to cut must be slowly guided by hand through the spinning blade to complete the cut. Table saws are extremely versatile in their ability when compared to other saws. Their simplistic design makes them able to accommodate extremely awkward and unorthodox cuts. The blade of a table saw is also adjustable, meaning it can be raised or lowered to increase or decrease the cut’s depth, depending on the need.

What Are Table Saws Used For?

When it comes to table saws, there is very little which they can not cut. Of all the standard saws, the table saw is, without a doubt, the most brute-force in nature.

How a Table Saw Fence Works

A table saw fence, sometimes referred to as a guard, is a wall/straight edge fitted to the top of the table saw and adjustable. When the fence is attached, it forms a 90° angle between the table and fence and runs perpendicular to the table itself.

• First, the fence provides a stable guide to slide the wood piece along while cutting to cut it in a perfectly straight line.
• The second thing that a table saw fence does is to increase user safety. It does this by eliminating the need to put your fingers and hands excessively close to the saw blade to guide the material.

If you are looking for a fence to go along with your table saw, consider checking out the PowerTec Rip Fence. (Check the Current Price on Amazon Here)

Are Table Saw Fences Necessary?

Fences are not always necessary, nor are they still possible to use. In some instances, the size of the material you are cutting will exceed the entire table’s size, rendering the use of a fence impossible.

Vega Pro 50 Table Saw Fence System

In this case, some saws will feature extendable table arms, which help to stabilize your piece as it is cut.

While fences are not entirely necessary, the difference in the straightness of the cuts you can make with them is substantial in place vs. without it.

Table Saw Fences Are Not All Created Equally

If you’re going to shop around for a fence for your table saw, you may have noticed that many of them look similar, but do not be deceived.

Admittedly, many fences are standardly sized and will be accommodatable by most saws, but this is by no means true for all table saw fences. This is why it is always advisable to stay within your brand and not attempt to cross-fit a random guard you have picked up from a third party seller.

Fences that are incompatible may be either too large or too small to clamp onto the rail of your table saw, rendering them useless.

Never attempt to use a loose, wobbly, crooked fence, or unsuited to your saw in any way. Failure to use a properly fitting guard will increase the likelihood of a serious accident or injury occurring. Don’t take the risk.

Similar Types of Saws

Although table saws are an immediate go-to for making most cuts, some other saws may be more specific to perform certain tasks due to their ease of access and are more favorable than a table saw.

Here we will briefly name each one, describe their design structure, and explain which tasks they are best suited for:

Skill Saw

A skill saw is a handheld circular saw, which features a blade identical to that of a table saw. Because however, a skill saw is operated free-handedly; it is not ideal for making precise cuts.

A skill saw’s main benefit is that it can rip through pretty much anything very quickly, so if accuracy is not of great importance, a skill saw is incredibly convenient.

Miter Saw

A miter saw is another circular bladed saw, but instead of being handheld or protruded from a table, a miter saw blade is fixed to an arm that moves directly up and down.

Miter saws can make angled cuts and have a built-in fence, granting accuracy and safety for the user.

The main drawback of a miter saw is that it cannot handle large surface cuts and is best used for smaller pieces such as baseboard and 2×4.

Safety Precautions When Using a Table Saw

When using any saw, safety is crucial—but table saws can be particularly dangerous.

• When using a table saw, never put your fingers closer than six inches to the blade at any time. Most table saws indicate the “danger zone” by way of a red circle surrounding the blade. Never go within this.
• If cutting a very large piece of material, such as a full-sized plywood sheet, have another person help hold it as you guide it through.
• Always make sure your work area is organized, clean, and clear of any tripping hazards before you begin working with any power tool.
• Never make any cut without proper safety eyewear. Safety glasses are essential for protecting your eyes from permanent damage.

Final Conclusion

In this article, we set out to determine whether or not table saw fences are universal. We first looked at how table saws function and operate and the need for a fence. From there, we examined how the table saw fences attach to the rail of the table.

Finally, we concluded that while many table saw fences are standardized and will work on most different saws, they are certainly not universal.

Different companies may design their rails and fences in slightly different ways, making them unsuitable for table saws from other brand names.

In closing, always research the specs of your table saw before committing to a fence which may not fit; and most importantly, always put your safety and the safety of others first and foremost.

The Best Miter Saw Fence Systems For Your Saw

There are few miter saw upgrades better than adding a miter saw fence system. From quick one-time cuts to series of dozens or hundreds of cuts a fence on your miter saw workstation is a huge time saver.

And, a miter saw fence will improve the accuracy of the cuts.

• All-in-one fence systems from major manufacturers
• DIY components
• Combination miter saw stands fences (mobile or workshop)
• Features to look for in a fence system
• Review of the Kreg KMS8000 fence

Lastly, while it’s tempting to build a DIY fence, the value and accuracy of an all-in-one system is generally worth the cost.

Professional stand fence:

Subscribe for a FREE directory to 300 hand-selected local and online hardwood retailers.

What is a Miter Saw Fence System

A miter saw fence system is an add-on to your existing miter saw that provides an integrated fence with stop blocks and a measuring system. Using the measuring system you can put away your tape measure and pencil while making cuts. And, using the stop blocks you can quickly cut 5, 20 or 500 cuts with the same precision on each cut.

Who Makes Miter Fence Systems

Not surprisingly, this niche of products isn’t widely covered. But you will find fence systems from the following well known tool suppliers:

What’s the most popular miter fence? Arguably, the Kreg KMS8000 as it’s sold by Kreg (the makers of dozens of woodworker helping jigs) and it’s market longevity. In fact, for over a decade, this model has changed very little.

Alternatives to a Miter Fence System

Not sure you want to invest in a complete system? There are a few options, but you’ll give up some flexibility, speed and very likely precision:

• DIY miter fence tracks can be made using t-track and a custom wood block. But, what you save on cost, you give up accuracy of the custom-made rails found on purchased kits.
• Custom wood fences are the “old school” solution with a self-adhesive ruler and custom stop blocks
• Or, something I’ve used a few times, a simple wood stop block pounded into the bench. Not exactly a fence, but an effective stopper. It’s just slow and good for 12″ cuts on most benches where you miter saw is integrated into the bench.

Best Miter Saw Fence Systems

Perhaps surprisingly, there are NOT a lot of suppliers of miter saw fence systems. So, with that, there are both all-in-one systems and DIY kits to economically expand your saws capabilities.

Overview

New in 2022, the StealthStop resolves a few of the biggest complaints about the Kreg jig: ability to firmly lock in the stop. and maintain pre-sets.

However, Woodpeckers (a top brand in woodworking) went further and created a unique flip-up design that allows for multiple pre-sets to be made. And, when you’re done with that cut length, simply fold it away and use the saw with other stops.

Editor: I decided to replace my Kreg Miter Saw System with this after I upgraded to a Festool Kapex. I’ll update this review the results soon.

Key Features

A Made In the USA product, this precision track and stops will allow or industrial grade cutting without needing to worry about the flip stop moving or flexing.

The primary drawback of this fence? Well, versus the Kreg or like your table saw, the stop doesn’t directly connect to the measuring tape. So you’ll need a combination square to link the two. A bit slower if you are making dozens of different length cuts.

• 96 inches of total track
• Four stops
• Mounts horizontally or vertically
• Stops flip away
• Micro-adjustment built into stops

Overview

From the popular Kreg Tools comes the Precision Trak system that offers both miter saw and drill press fences up to 96″. And with Kreg’s track record of providing durable products that last, this is a fence system to seriously consider.

Using a decade-plus old design this system operates in combination with a wooden fence to offer a left and right hand fence setup that installs in just a few hours.

And, of course, with this being part of the Kreg lineup of products there are instructions included on building the fence system with the popular hole system from Kreg.

Editor: After needing a miter saw on my own saw, I ultimately chose the Kreg and have installation instructions and a further review below. I chose it because I wanted ALL of the pieces in one package. And I liked the wide ruler and two stops.

Key Features

• Includes two stops for production use or swing-away functionality
• Precision lens for clear view to your cut length
• 8-feet of track in 2-foot lengths
• 2 self-adhesive measuring tapes that can be cut to length

Review. Kreg Miter Saw Fence Stop System

By giving you a complete box of all the parts you’ll need, Kreg lets you decide your configuration. And, includes the stops, measuring tapes and short lengths to allow you to setup equal fences on both sides of your saw. Or 24″ to the right and 72″ to the left. Or…you get the picture.

After installing this system one of the features I really liked was the tension adjustable swing-away stopper. Since sawdust inevitably pushes its way down the fence you can lift the stopper off the fence and let the dust slide by. Thus preventing an inaccurate cut.

• 96 inches of track
• Two stops (production swing away)
• Locks in place rigidly
• Easy to adjust and set length
• Design your own fence

Overview

Along the similar lines of the Kreg, but allowing for flexibility in length (and reduced cost), the Rockler system lets you buy shorter lengths and customize your track.

With this 36″ DIY kit you’ll be able to make left or right handed systems by adding in your own tape measure and stops (sold separate, also from Rockler).

Key Features

• 36″ overall length
• Double T-Track design for a stop and tape measure
• Aluminum construction
• Pre-drilled holes for easy installation

Review. Rockler Miter Saw Fence Stop System

Where Kreg packs everything you’ll need into one box, Rockler has taken a different approach and lets you buy a shorter length of double T-Trak. And, by adding on extras of your own choosing you can custom build your stop system to your saws needs.

• Shorter lengths of track to DIY design
• Less cost vs. Kreg KMS8000
• Slide-in T-Track tape measure
• Optional flip-stop with lens
• Tape measure not as clear to read as Kreg
• Assembling more than 3 of these systems equals the (larger) Kreg kit cost
• Best for a single extension

Overview

For a tighter budget, the POWERTECH system offers up a double T-Track kit that includes the track, measuring tape and plastic track. However, the POWERTECH flip stop is optional but an economical add-on.

Key Features

• 36″ overall length
• Double T-Track design
• Right and left measurements
• Extruded aluminum
• Pre-drilled holes for easy installation

Review. POWERTECH Double T-Track Fence System

The biggest factor with POWERTECH versus similar offerings is it’s price.

If your view is 5 savings on the same product can be spent on a drill bit, then the POWERTECH miter saw fence system was built for you.

• Shorter lengths of track to DIY design
• Less cost vs. Kreg KMS8000 Rockler
• Slide-in T-Track tape measure
• Optional flip-stop with lens

Installing the KREG KMS8000 Miter Saw Fence System

After looking at the options, I decided to go with the Kreg KMS8000 as it had all the components I needed:

• One kit with all the components
• Enough for 48″ to the right and left of my miter saw (I chose 54″ right, 24″ left)
• While restricting double bevel cuts, I chose to install it as a zero clearance fence (more later)
• Single track with the BEST visibility to the Kreg left to right and right to left tape

It’s worth repeating and noting that. The Kreg system is a single track with the best visible tape system. You’ll thank your eyes later when you’re not squinting into a smaller T-track based tape.

Unboxing the Kreg Miter Saw Track

Kreg isn’t the leader in jigs by luck. So, it wasn’t a surprise when I opened the miter saw track kit and found everything neatly packed in a well thought out tray system.

All the pieces were separated during shipping, no dings, and no mars.

However, like any woodworker, your first reaction might be a reaction to the volume of parts that were shipped. But, in the end, it took more thought on designing the fence box system.

Choosing Your Fence Extensions. Longer Left or Right?

Even though my saw is a 15-year old Makita I didn’t think twice about building around it given it’s durability. So, the first order of business was setting up a 24″ left fence and a 54″ right fence.

It’s worth noting, when you’re building the fence there is a bit of freedom here:

• Your bench may dictate which side has the longer fence (right or left)
• Or, if you’re like me, I’ve grown accustomed to feeding stock left to right. So while it could be easier to have the primary fence stop to the left, it would undo 25 years of cutting experience.

Making the Fence System Supports

First, you may notice from the picture that the 3/4″ plywood was pre-finished. For some reason, this plywood was cheaper than an unfinished sheet of the same B-grade. So, rather than spend time later on finishing I went with it.

For the fence supports there are all kinds of options. But, having been down the build path, I’d recommend:

• Well, first, read the instructions. Kreg offers up a simpler solution than I conjured up using their hole system. Of course.
• Make sure to plan the height of the box so it is perfectly flush with the miter saw.
• Remember to think of the overall fence length, and match the box to that length (plus overhang).
• Use glue and screws

Adapt the Fence Table and Stop to your Saw

While I chose to install the fence as a zero-clearance fence, I still needed the saw to move left and right to a full 45-degrees.

Which, you are probably guessing, means clearance to the right and left is required both for the saw AND your hands. So, be sure to plan this out ahead of time and make the proper adjustments.

Editor: Make sure to setup, test out your configuration, and adjust every part of the fence system before making final glue-ups and screwing.

The Biggest Fence Decision: To Extend or Overlap

If your miter saw is anything like mine, you’ll find you will have at least 10″ to the left and right that won’t have a fence stop.

Unless you take the (not so obvious) approach of installing the miter saw fence system IN FRONT of the existing fence.

So, while you lose a double bevel capability, you gain a much more accurate fence system with stops up to about 3″. And, this is where the the FastCap 10-million Dollar Stick comes into play. Holding short sticks next to a saw is an absolute DO NOT attempt.

The other option? Sacrifice a miter fence stop the first 10-14″ and start the system further away from the blade.

Installing the Miter Fence and Stops

Following the instructions, and after your fence blocks are built, simply install the Kreg T-trak on top of a 3/4″ thick fence block (you’ll need to drill the holes).

• On the left of the saw I only needed one 24″ track, and due to my saws existing fence had a 8″ setback before the fence stops could come into play
• On the right of the saw I had two joints where the 24″ rails butted together. Be sure to spend some time and PRECISELY align them…
• …or you’ll be catching the sliding stops on the tracks for years to come.

Choose Where Your Miter Saw Fence Stops Will Go (Carefully)

Interestingly, and something I didn’t think through first, the stops are made to be assembled for use on the left or the right of the fence.

So, take a few minutes and decide which miter saw stop you want on which side.

Personally, I like the swing away stop on the long side of the fence. If you adjust the tension correctly it can sit 1/4″ off the fence block base and allow sawdust to slide by.

Install the Adhesive Tapes

After the fence is setup, one of the last steps is installing the adhesive tapes. So, in this step the biggest trick is setting the tape EXACTLY in place.

With that, as you might have guessed, follow the instructions carefully as the tape will decide your long term capability.

Frequently Asked Questions

How do you make a miter saw fence?

The best way to make a miter saw fence is to use a fence system. These systems come with either a single or a double T-Track that hold an adhesive tape and the miter saw stops. Then, simply build a fence to the specifications and attach to your bench.

Does a miter saw need to be bolted down?

Bolting or screwing your miter saw down is both an improvement in safety as well as improved accuracy. In fact, for sliding miter saws bolting it down is a necessity as the sliding action will pull the saw back and forth.

What is the best way to control dust on a miter saw?

For miter saws the best way to stop dust is by installing a dust hood that wraps around the saw and connects to your dust collection system. And, the best hoods are lighted to ensure the shroud doesn’t darken the cutting area.

Summary

With just a handful of miter saw fence systems on the market, the Kreg jumps out as a top solution for most. But, if cost and a smaller fence stop is your goal there are a couple of dual T-Track systems for your saw.

Last update on 2023-05-13 at 10:25 / Images from Amazon

Eric has been a professional woodworker for over thirty years and has worked in small cabinet shops making everything from kitchen cabinets to hand-made furniture. Now working from a home woodworking shop Eric is sharing his passion for woodworking, tool advice and how-to knowledge from his Minnesota-based woodshop.

Leave a Comment

Subscribe for a FREE directory to 300 hand-selected local and online hardwood retailers.

Joining wood is one of the most basic and essential tasks in woodworking. But there are over a dozen types of woodworking joints. Learn what is best for your shop, budget and skill in this guide.

Standard screws were not designed for the shear load that cabinets generate. Which makes finding the best cabinet screws a must both for ease of installation and safety.

When comparing biscuits vs dowels the number one consideration is often cost. But woodworkers know joint strength, speed of setup and alignment ease are key considerations. Learn what joint is best for your projects in this guide.

If you haven’t built an outdoor structure before a common question is a basic, but great one: what are the best screws for outdoor use? In this guide learn how to pick the right exterior screws for your project.

A drum sander allows woodworkers to build larger, more intricate projects with improved speed and quality. In this buying guide learn what the best drum sander is for your small or large woodworking shop.

The best clear wood finishes will apply easily, provide years of durability and not yellow wood over time. Learn what clear coats for wood are highly rated for indoor and outdoor use.

Disclaimer: DIY projects can be dangerous, hire a professional (link to Home Advisor) if unsure.

About the Author

As a woodworker with over 30 years experience, 100 kitchens built and many other projects I’m sharing my tips, tricks and tool choices on this site. Be sure to check out my favorite woodworking charity Sleep in Heavenly Peace that builds beds for kids who sleep on the floor.

Subscribe for a FREE directory to 300 hand-selected local and online hardwood retailers.

Affiliate Disclosure

Disclosures: (1) If you click a link on this site and buy something I will earn a commission. (2) CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED ‘AS IS’ AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME. (3) Product and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product. (4) As an Amazon Associate I earn from qualifying purchases linked from this site. (5) Amazon and the Amazon logo are trademarks of Amazon.com, Inc, or its affiliates.

Copyright (c) 2023 LEAN Woodworking LLC. Images are copyrighted and may not be used without explicit written permission.

This website uses cookies to improve your experience and track site visits. By visiting this website, you opt-in to the use of cookies. OkPrivacy policy