Angle Grinder Stand. Angle grinder chop saw

Transform Your Standard Angle Grinder Into A Chop Saw!

Do you want to make flat and straight cuts with your angle grinder? Are you having a hard time creating squares and getting the right angles?

Why do you need an Angle Grinder Stand?

As you know, an angle grinder, also known as a side grinder or disc grinder, is a handheld power tool used for grinding (abrasive cutting) and polishing.

This stand will transform your standard angle grinder into a chop saw for precise cutting of pipes, woodblocks, and other materials.

Compared to cutting materials freehand, this Angle Grinder Stand is safer and simpler to use.

Just bolt your 100. 125 angle grinder to this stand onto your workbench and you instantly get better control of the cutting wheel.

Why buy our Angle Grinder Stand?

This Angle Grinder Stand is made with a heavy-duty iron base and has an array of fully adjustable parts.

Features a retractable blade guard. a miter clamp with a maximum tightening size of 80 mm and 45-degree capacity and vice jaw that holds square or round stock securely.

Works on even the thickest of strip metal and allows you to cut from various angles without breaking a sweat.

It comes with a strength reinforcing lever with spring-return for comfortable and accurate work.

With this durable and easy to operate tool you’re sure to make clean cuts in seconds.

Frequently Asked Questions:

Question: How to adjust the angle on the clamp? Answer: Loosen the screws to adjust the position and angle of the clamp. Tighten the screws after the position has been adjusted. Ensure that the workpiece is in the center of the cutting disc.

Question: How to set the grinder on the cutting slot? Answer: Loosen the adjusting screws and move left or right to ensure that the cutting blade is aligned to the hole of the cutting base, tighten the screws and make sure that the angle grinder is fixed securely.

Question: How to secure the base to work table? Answer: There are two (2) screw slots from the base (upper and lower part), create a screw slot on your work table to securely fix the angle grinder stand in place.

How to choose a suitable angle grinder:

• The cutting disc diameter should be 100-125mm.
• Both sides of the angle grinder all should have the handle hole.
• The size of the angle grinder head should be no more than 85mm.
• Fix the handle onto the stand with the washer and nut provided.
• Fix the angle grinder onto the holders with screws and nuts.
• Adjust the adjusting screws to ensure that the cutting blade is vertical to the base and that the angle grinder is fixed securely.
• Press down the handle and check the position of cutting blade, it should be within the cutting hole of the base. If not, loosen the screws and adjust the position of the stand accordingly.
• Fix the protective guard.
• Run the grinder for a few seconds, switch off.
• check that all screws, nuts, and bolts are tight.
• Use protective gear gloves, face shield, and earplugs when cutting any materials.
• The stand must be secured to a firm level surface.
• Ensure that no flammable materials are in the area before starting work.
• Sparks from the grinder will damage paint, glass and other surfaces.

1.1 Rotate the screw knob and loosen the clamp.

1.2 Put workpiece in the clamp and then tighten the screw to hold the workpiece securely.

2.1. Switch on the angle grinder and press down handle to cut the workpiece with the angle grinder.

2.2. Start cutting with slight force and apply even force during cutting.

Package Specification:1 x Angle Grinder Stand

What are you waiting for? Get any DIY project or professional job done by modifying your angle grinder into essentially a mini chop saw!

You can have the ability to create square and flat cuts on metal, wood or other materials with ease using a tool that’s just a little bigger than a lunchbox.

So if you want straight and precise cuts save some money and space on your workbench, then this Angle Grinder Stand is the ideal tool for you!

Payment Security

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Refund Policy

We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.

To be eligible for a return, your item must be in the same condition that you received it, unworn or unused, with tags, and in its original packaging. You’ll also need the receipt or proof of purchase.

To start a return, you can contact us at support@2simpleagency.com. If your return is accepted, we’ll send you a return shipping label, as well as instructions on how and where to send your package. Items sent back to us without first requesting a return will not be accepted.

You can always contact us for any return question at support@2simpleagency.com. Damages and issues Please inspect your order upon reception and contact us immediately if the item is defective, damaged or if you receive the wrong item, so that we can evaluate the issue and make it right. Exceptions / non-returnable items Certain types of items cannot be returned, like perishable goods (such as food, flowers, or plants), custom products (such as special orders or personalized items), and personal care goods (such as beauty products). We also do not accept returns for hazardous materials, flammable liquids, or gases. Please get in touch if you have questions or concerns about your specific item.

Unfortunately, we cannot accept returns on sale items or gift cards. Exchanges The fastest way to ensure you get what you want is to return the item you have, and once the return is accepted, make a separate purchase for the new item. Refunds We will notify you once we’ve received and inspected your return, and let you know if the refund was approved or not. If approved, you’ll be automatically refunded on your original payment method. Please remember it can take up to 10 days for your bank or credit card company to process and post the refund too.

Cut-off Tool vs Angle Grinder (Difference Uses)

In the metalworking world, two of the most common tools we come across are the Angle Grinder and Cut-off Tool. Both of these tools are used for the purpose of cutting steel, but they do have some significant differences in their functionality and practicality.

In the following text, we shall investigate some of these differences and try to help you to evaluate which will better suit your project.

Difference Between an Angle Grinder and Cut-off Tool

To keep it clear and simple, the most obvious difference between the angle grinder and cut-off tool is found in their differences in flexibility. The angle grinder can be used not only for cutting but also for the grinding, sanding, polishing, and weld prep of metal while cut-off tools are only useful for cutting steel. Additionally, we see many further differences between the two however, we shall investigate these further on.

What is a Cut-Off Tool?

A cut-off tool is a lightweight hand-held tool that is approximately 6 inches in length that specializes in the cutting of steel. It consists of a cutting disc (wheel) which is usually about 3 inches in diameter and depending on the model, can be positioned length-ways to the tool’s body or parallel.

The difference between the models that have a disc located length-ways vs parallel is the overall accessibility to the job at hand. This in fact proves to be highly advantageous when attempting to cut metal in locations that have limited accessibility. Types of Cut-off Tools. Photo by: Keith Homan/Shutterstock.com

What Is Cut off Tool Used For?

Cut-off tools are used for the cutting of metal that is generally no thicker than 1 inch. They are also excellent for making cuts in locations that are difficult to reach which makes them extremely practical for panel-beating and sheet metal fabrication situations. However, their usage is restricted with the cutting of heavier metals due to power limitations and disc diameter.

Sometimes referred to as a disc cutter, you can use this power tool to cut plastic, soft metals such as aluminum, brass, hard materials such as stainless steel etc.

Cut-off tools are most often powered by electricity, pneumatic power, or air pressure and have a power range usually maxing out at 1HP.

Note: Do not get confused with a metal cutting chop saw which uses a much larger abrasive cutting disc mounted on a hinged arm.

What is an Angle Grinder?

An angle grinder is a multi-purpose tool used for grinding, sanding, polishing, and weld prep of metal. It comes in various sizes with discs ranging from 4.5” (115mm) and 9” (230mm) with motor sizes that vary from 3-7hp, this makes them highly versatile and useful for heavy-duty applications and more delicate work alike.

Unlike cut-off tools, the disc of the angle grinder is always located parallel to the grinder’s body which does limit their accessibility at tight spots. However, despite this limitation, they are still highly useful for all manners of jobs and can be used upon materials such as metal, plastic, wood, and masonry products. The versatility and the uses of an angle grinder are discussed in detail here.

The most common and practical way to power an angle grinder is via electrical input; however, lithium batteries are also useful for working in locations without accessible electricity but they prove to be fairly limited in their power range.

Angle Grinder vs Cut-off Tool

The following comparison table should give you a quick summary on how these two power tools compare each other.

Functions

The primary functions of the cut-off tool revolve completely around the cutting of metal rods, bolts, rebar, and other cross-sections to the desired length.

On the other hand, an angle grinder is a very versatile tool. You can use an angle grinder for cutting metal, grinding, sanding, polishing, deburring, and weld preparations.

Although the grinder is a much more useful tool, when discussing the field of its application, the cut-off tool is superior with its accessibility to hard-to-reach locations.

Depth of Cut

The cut-off tools have a 3-inch abrasive cutting disc which can cut up to a depth of 1-inch. Some models with right angle orientation are limited to a depth of cut of ¾.inch.

The angle grinder is highly versatile when concerning material thickness and size and is not extremely limited in its accessibility as machine sizes differ to suit. A 9 ″ angle grinder can cut up to 3.5 inches deep.

Size

A disc size of 3-inches is the standard for most of the cut-off tools (which corresponds to its limited verbality in cutting thicknesses). This tool has a very compact and lightweight design; thanks to the smaller disc size and corresponding smaller motor.

With disc sizes ranging from 4.5 inches to a huge 9 inches, angle grinders have a variety of different sizes to suit each specific job.

Power

These tools are usually powered by compressed air or electricity. An electric cut off tool has a mere 1HP average is a fairly low power input from a power tool. This is useless with tougher and thicker materials.

Angle grinders have a power rating ranging from 3HP – 7HP the range of angle grinders is wide and practical for all projects.

Speed

Cut-off tools can run at very high speeds ranging from 18,000 to 28,000 rpm. While they do not have the power of a grinder, they excel in speed.

Grinders have much slower speed ranging from 6000 to 8000 RPM with some models going up to 12000 RPM.

Safety

The safety guard on the cutting-off tool covers less than half of the wheel which increases the risk of the tool kicking back onto the user. However, despite this, its small size means the potential injury has lesser impact and dust/noise pollution is minimal when compared to grinders.

Safety guards are a common accessory with all the angle grinders and when used correctly, they protect the user from injury. If an injury does occur from grinder kickback, however, it is usually severe.

Dust/noise pollution is more recessive when compared to cut-off tools.

Although the use of safety guard and personal protection equipment like safety glasses can protect you, keep in mind that improper use of abrasive cutting tools can be very dangerous. Follow the grinder safety instructions and tips very carefully.

Price

Both tools are relatively inexpensive. You can find cut-off tools as low as 40USD for a model with very basic capabilities although for a heavy-duty cordless model expect to pay at least 80 USD or more.

Slightly more expensive are angle grinders with basic models costing approximately 50USD

Which Tool Should I Get?

When to Purchase a Cut-Off Tool?

One should consider the cut-off tool as their primary choice of cutting tool because two or more of the following factors are important to you or your project:

• The material cross section to cut is not more than 1 inch.
• You are on a very low budget
• The cut is located in an area of difficult accessibility
• Where user safety or pollution is of a concern
• When low power consumption is required

Who Should Get an Angle Grinder?

One should consider the angle grinder as their ideal choice of cutting tool because two or more of the following factors are important to you or your project:

• When heavy-duty tooling is required for cutting a range of material thickness
• If you need versatility by being able to complete a range of tasks with the same tool (eg cutting and polishing)
• You need a tool that is long-lasting and can withstand regular heavy usage.

Closing Thoughts

The Angle Grinder and the cut-off tool are two very different types of tooling despite some similarities. When considering buying or making use of grinders or cut-off tools for specific jobs, take the time to consider the discussed factors to achieve a successful, safe and productive purchase.

Magical Grinders; The Best Angle Grinders in 2023

Using Angle Grinders to Cut Metal is one the most convenient ways of metal fabrication as angle grinders are a metalworker’s right hand; You can tackle a wide range of metalworking operations with the right angle grinder equipment and accessories while staying safe on the job. An angle grinder is a versatile tool that may be used to work with a number of materials and applications.

Can You Use Angle Grinder to Cut Metal?

“Can you use an angleAngle Grinders to Cut Metal?” is a question that pops up frequently on the appropriate message boards. What’s the quick and easy answer? Absolutely! Indeed, among the many hand-held equipment available, the angle grinder appears to be the most flexible of metalworking power tools. That’s why it’s no surprise that this specific item is utilized by a variety of crafts, including those in the automotive sector, HVAC, plumbing, and a variety of others.

Grinders are often used for refurbishing and polishing metal materials, so it shouldn’t come as a surprise that you can use them on stainless steel surfaces if you have the correct disc.

You shouldn’t, however, go into the process without taking any safeguards. That’s why, throughout the post, we’ve included a few safety guidelines to assist you learn how to use angle grinder to cut metal in the most efficient and effective way possible.

How to Use an Angle Grinder to Cut Metal

Now that we’ve established the notion of using an Angle Grinders to Cut Metal, let’s examine what the optimum way of operating an angle grinder to cut metal. We must point out that the method is not always the same because different angle grinder models work in different ways. Even yet, the safety measures you must follow while cutting metal or steel are very similar.

What is the maximum thickness of steel when operating an angle grinder to cut metal?

It truly relies on the angle grinder’s cutting capacity as well as the size and type of disc you’re using. Apart from that, the thickness of the material you’ll be cutting is a determinant in determining the steel’s possible cutting depth.

Not only that, but cutting discs come in a variety of thicknesses, so you’ll need to pick the proper one.

But let’s pretend you’re using a 4-1/2-inch grinder with a flat diamond cutoff blade to cut stainless or mild steel, as most people do. A 1mm or 1.6mm iron-free disc should be used to cut the stainless steel.

When cutting thin metal materials like sheet metal, a 1.0mm or 0.8mm cutting disc is recommended. Due to the reduced blade thickness that results in less heat transmission, any of these discs will provide a cleaner appearing cut and minimize any potential discoloration.

When cutting or buffing metal or aluminum with an angle grinder, using a type saw lubrication will extend the disc’s life and prevent the risk of chipping.

If you’re going to chop thicker, heavier steel like rebar or structural steel like angle iron, you’ll need a cutting disc with a thickness of 1.6mm or 2.5mm. Using a bigger blade, such as a 2.5mm cutting disc, to cut through dense steel has certain disadvantages.

Due to the slower blade speed of the bigger disc-equipped, the completed cut of your steel workpiece may show evidence of discoloration. What is the reason behind this? Because of the increase in friction, essentially.

You could always use another power tool to cut metal, depending on how thick the material is and how clean of a cut you want.

While accuracy and elegance are required when cutting thick, dense steel, a metal cutting circular saw or a metal chop saw are two of the most common suspects. Break out the trusty grinder if all you want to do is make short cuts when accuracy and overall aesthetics are secondary concerns. Simply use the suggested CDs whenever possible.

The Best Angle Grinder for Metal Work

If you’re looking for a high-quality, easy-to-useAngle Grinders to Cut Metal with, here we present you some of the best tools in the market today.

Bosch 4-1/2-Inch Angle Grinder

The Bosch 4-1/2-inch angle grinder has a powerful 6.0amp motor that produces 11,000 no load rpm for professional cutting and grinding. Its Efficient motor has a very tiny field diameter, allowing the operator to grind or cut with minimal effort. This item is lightweight, with a small size and shape that makes it suitable for metal craftsmen. Vehicle fabricators, plumbers, and other professions who utilize grinders on a regular basis, such as home builders, are among those who employ them.

Ronix 3212 Angle Grinder, 2350W, 230mm

Having a strong an Angle Grinders to Cut Metal and other difficult materials is a huge benefit for a professional metal worker who conducts a lot of grinding and metal fabrication operations. The Ronix 3212 Angle Grinder is a powerful power tool that can tackle a wide range of industrial and heavy-duty tasks. You can confidently operate this angle grinder to cut metal any time.

Makita 9557PBX1 4-1/2″ Cut-Off/Angle Grinder

Makita’s angle grinder is a high-quality tool for metalworkers. A powerful 7.5 AMP motor provides high output power in a smaller, lighter tool. You may carry this device anyplace and cut metal with ease by using both hands to control it.

The ‘tool-less wheel guard adjustment allows effortless clamping, and it also offers a grinder with an AC/DC switch for use with various power sources, which is a nice feature of this Makita angle grinder.

Safety Tips When Operating an Angle Grinder to Cut Metal

When you use Angle Grinders to Cut Metal or grind it, small chips or shards of metal fly all over the place. They can also be fiery and abrasive. Follow these guidelines to avoid eye injuries, wounds, burns, and other problems when cutting metal: Read and follow all safety warnings on metal-cutting discs and blades. Protect your eyes and ears with safety glasses, a face shield, and hearing protection. Wear gloves, a long-sleeve shirt, and slacks to protect any exposed skin.

Let newly cut metal cool completely before handling it.

When working with metal that may have sharp edges, use gloves.

Before cutting metal, secure it with a clamp. If you’re use angle grinder to cut metal, don’t let anyone close you unless they’re wearing hearing and eye protection.

Suggested disc types.

You can use angle grinder to cut metal and all types of it, including bolts, angle iron, rebar, and even sheet metal, when it’s equipped with an abrasive metal-cutting disc. However, as you use the discs, they wear down fast, cut slowly, and reduce in diameter. Instead, we recommend utilizing a diamond blade with a ferrous metal cutting rating. These will last far longer than abrasive discs, cut quicker and cleaner, and wear down much slower.

The Disc Type	Application	Consideration
Metal cutting disc / cut off disc	Most metals can be cut. It can’t be used to grind anything. Present at a 90-degree angle to the workpiece	Aluminium Oxide is used to make the cutting edge
Grinding disc	Metals, both ferrous and non-ferrous, are ground. Present at a 45-degree angle to the workpiece.	Aluminium Oxide is used to make the cutting edge.
Multi-cut cutting disc	Metals, both ferrous and non-ferrous, are cut through (including stainless steel). For more sophisticated cutting needs, it will also cut through brick, stone, contemporary composites, and tiles.
Stainless steel cutting disc	Steel and stainless steel are cut through. It’s especially handy for cross-sections with tiny cross-sections.
All cut diamond blade	Cast iron, various ferrous and non-ferrous metals, and most building materials are all cuttable.	Cutting edge with diamond grains attached to it.
Abrasive grit mop disc	Metal grinding in general, especially for edge grinding jobs like deburring, sharpening, and surface finishing.	Grinding flaps in a fan-shaped radial pattern.
Slitting disc / thin cutting disc	Pipes and profiles with thin walls are cut. This tool creates a fine cut line. Use on ferrous and non-ferrous metals, as well as stainless steel.	Thin cutting discs produce less heat during operation, cause less tool vibration, finish cuts faster, and waste less metal in each cut, saving up to 2 mm each cut.

FAQ1. What tools do I need to cut metal with an angle grinder?the necessary tools when it comes to metal cutting with angle grinder are: angle grinder, metal disc, c-clamp, power outlet/source, earmuff and the metal material you plan to use.

What’s the difference between a cut-off tool and an angle grinder?A cut off tool is used to cut surfaces, as its name implies. The angle grinder, on the other hand, is a more flexible tool that can be used for a variety of activities such as sharpening and grinding.

Is it possible to cut steel with an angle grinder?Yes, if you have the appropriate disc. However, due to the steel’s hardness, they will wear out more quickly.

Is it possible to useAngle Grinders to Cut Metal. even a thick steel piece? Yes, it surely can. At the end of the day, cutting metal with an angle grinder may be very effective and incredibly safe if you have the proper equipment and safety gear.If you’ve never used a grinder before, you won’t need much practice to learn the skill of slicing and dicing materials properly. That is, as long as you use the suitable cutting disc with this powerful hand-held equipment.Because an angle grinder is designed to cut through stronger metals, as well as bricks and concrete, you won’t have to worry about its durability. In time, a decent grinder will become a need rather than a luxury.While the ordinary DIYer is unlikely to be hacking at dense steel on a regular basis, a good grinder is the one equipment you’ll want in the back of your truck or tool shop if you need to make Rapid cuts in metal.Finally, when using a grinder, make sure you are in complete control of the equipment and that you are wearing the proper protective safety eyewear. All that’s left to do now is select the appropriate cutting disc and material, and begin cutting metal with ease.