Bosch art 23 easytrim grass trimmer replacing the blade

How to Remove the Reel from an Electric Grass Trimmer

Grass trimmer, gasoline or electric, is the only right solution for mowing grass in hard-to-reach places where you can’t work with a wheeled lawnmower. Trimmers use metal blades or a special trimmer line as a cutting tool, which is hammered into the grass trimmer reel. But unfortunately, three-dimensional heads become unusable over time. Some malfunctions can be fixed with their own hands, and some require a complete replacement of the mower.

trimmers for the grass with the installed blade are most convenient for cutting high and coarse grass in the country. The line for the trimmer on your brushcutter fails in such cases. Thin one tears very quickly. Using thick 2.3 mm cord or homemade rope rods cause vegetation to wind up on the bobbin. This increases the engine load. As a result, the piston group and other mobile units of the device wear out very quickly.

If you mow weeds with an electric trimmer without a blade, you won’t solve the problem with a single line, even if it’s thick with a shaped section. There is always a risk of overheating the electric motor and damaging the flexible shaft. And the problem is in the high torque of the electric motor. Grass wrapped around the spindle creates strong resistance to the shaft, resembling a speedometer cable, which cannot withstand and twists.

In order to save technique from premature wear manufacturers have provided the ability to install special blades on trimmers for grass. The design and shape of existing cutting elements allow you to easily cope not only with rough and overgrown grass, but also successfully deal with young shrubs and bushes.

Which blades for electric mowers and lawnmowers

Before you buy a trimmer blade, let’s find out what materials are available and when they are used. Today, manufacturers offer the consumer a large number of types of these consumables. In general, all cutting tools designed for mowing the grass can be classified:

The main material for the manufacture of trimmer knives can be plastic or metal. The use of such consumables largely depends on two parameters:

For safety reasons, manufacturers do not recommend putting steel knives on electric grass trimmers. Practically all battery- and cordless lawn trimmers are equipped with plastic blades. Depending on the manufacturer, they can be solid disc-shaped design, with several blades, or in the form of a special mowing head that provides for installation of removable plastic blades.

Straight boom on the gasoline grass trimmer and curved boom on the electric trimmer

To put a metal blade on the electric grass trimmer does not allow its design features.

• Curved boom reduces the distance from the working part of the machine to the mower’s legs. If the blades collide with a rock or other hard object, the grass trimmer is thrown back to its feet.
• The high torque mentioned above in case of a collision between a metal blade and a hard object transmits a high load to the flexible shaft of the grass trimmer and its motor. Which causes them to fail prematurely.
• The handle of chain saw has no stop bar most often. That doesn’t mean you can’t hurt your feet.

These features enable plastic blades only to be used on electric-powered trimmers. blades collide with obstacles to break, thus protecting the mower’s legs from possible injury.

Plastic blades handle overgrown and dry grass well. Nettles and burdock stems can be mowed with these blades.

metal blades are used only on gasoline-powered trimmers because of their design features.

• The straight boom design creates greater legroom for better safety.
• Comfortable U-shaped and J-shaped handles give a firm grip. D-handles of brushcutters are equipped with a limiter that rests against the mower operator’s leg and prevents the cutting head from getting too close to the leg when the cutting disc hits a hard obstacle.
• The clutch of the petrol engine allows a smooth acceleration to the optimum speed. And when the blade hits a hard surface, it can absorb some of the impact.

So, gasoline grass trimmers with metal blade installed is best used on large areas. They can successfully cope not only with high rough grass, weeds, burdocks and nettles, but also bushes and young trees.

The shape of the blade on the disc trimmer for the grass has no effect on the quality of work performed. They do not affect the speed. Triangular, trapezoidal, rectangular forms are a marketing campaign of manufacturers.

If you are planning to make hay it is best to mount a brushcutter with more blades. Pay attention to discs with eight teeth or discs with four large blades and four additional blades. Two or three blade blades will shred the grass very hard.

You need help?

You have a question about Bosch and the answer is not in the manual? Ask your question here Give a comprehensive description of the problem and ask your question clearly. The more detailed the description of the problem or question, the easier it will be for other Samsung Galaxy A7 users to give you a comprehensive answer.

There is a problem when refilling the dispenser with a fishing line: I can’t remove the top cover. I’m afraid to break it myself.My model goes under the index ِART 2600 easy trim 3600h/78603.I’m asking for help from knowledgeable people.Perhaps someone has such a manual, would be happy to get it in the “soap”. If it is not possible, I would like to get at least general information on the subject, I myself am afraid to break.

How to open the cover to replace the bobbin on the Bosch ART 26 easytrim grass trimmer?

Bosch ART 26 Easytrim Specifications

Below you will find the Bosch ART 26 Easytrim product specifications and manuals.

FAQ

Can’t find the answer to your question in the manual? You can find the answer to your question below in our FAQ about the Bosch ART 26 Easytrim.

You can, but in dry weather the result will be better. When the grass is wet, clumps of grass easily form and can easily clog the mower.

Bosch ART 23 EASYTRIM 3600H78A00 Gear dispenser for grass trimmers. Manufacturer: Bosch.

Bosch ART 23 EASYTRIM 3600H78A00 Gear dispenser for grass trimmer. Buy F016L71599 for 909.00 online store seltop.ru. This part is original!

Gear dispenser for grass trimmer Bosch ART 23 EASYTRIM 3600H78A00 photo We are official Bosch dealers, we guarantee original replacement parts! The Bosch ART 23 EASYTRIM 3600H78A00 grass trimmer blade dispenser comes officially, sometimes the manufacturer makes a substitute article, our website takes this into account and if it says “analog”, it does not mean that it is a fake, it means that the manufacturer made a substitute.

About delivery: time and cost. We deliver all over Russia. than 2000 pickup locations. Russian postal service. info on shipping page.

Bosch ART 23 EASYTRIM 3600H78A00 Gear dispenser for grass trimmer. The part is original! Manufacturer: Bosch.

Payment by bank transfer (the invoice will be automatically generated in the shopping cart)

Spare parts are shipped only against prepayment!

After payment we will notify you about receipt of funds.

We will send you a tracking number after the delivery to the courier service.

Further notification will be made by the shipping company you chose when placing the order.

If you want to send an E-mail, just read the code:

Quality Parts. Delivery obligation. Reliability.

Your Seltop.ru

All information on the site posted to enable the buyer to become acquainted with the product before buying, and is not a public offer (art. 437 Civil Code). Product information on the site can be updated for several hours. Contact our manager for more information about availability and price at 8 (495) 221-07-05 from 6:00 to 18:00.

We do not sell fake parts. The advantage of genuine spare parts is that they are made in the same factories as the original parts. We give a 100% guarantee that we will refund your money if the part is no longer available or is no longer in production.

Prepare. remove and disassemble bobbin

Most models of electric and gasoline-powered trimmers require that you remove the spool to change the line. FUBAG tools allow you to skip this step. In order to make the manual versatile, we’ll take a closer look at it:

Fix shaft. Insert locking pin in bobbin case. It can be a thin screwdriver or a metal bar.

Unscrew bobbin case. In our example, strictly clockwise.

Unscrew the cover according to the direction indicated on the body.

The preparatory step is complete. You can move on to winding the fishing line.

How to wind fishing line onto a grass trimmer spool

Algorithm for winding

Install the line to the trimmer in the direction shown on the item.

Insert the short end into the groove on the side of the spool.

Tighten the long end in the opposite groove.

Place the spool with the wound line in the bobbin case.

Cut the line ends leaving 10 to 15 centimeters.

The filament change is complete and now you just need to screw the bobbin onto the grass trimmer and you are ready to work.

Once you’ve selected your trimmer fishing line for the headband, you’ll need to cut the amount of hair you need, since all the hair in the broom is not wound into a roll.

Remove the spool and the protective cap from the spool.

They are removed. We secure one end of the mowing line in the gap and carefully and evenly wind the trimmer line.

The volume of the cutting element should be such that the protective cover of the spool is closed, and the line for the trimmer on the spool is slightly unwound.

The other end of the hair growth line is planted in the hole in the protective cover.

Next, take the spool and the protective cover of the spool. Insert the end of the spool from the spool into the metal hole on the protective cover of the spool. Tighten the trimmer line slightly.

We put it all on the grass trimmer. Turn the spool clockwise until you hear a click.

Secured by. Now plug in the grass trimmer. We put the grass trimmer in its original operating position. Turn on the grass trimmer. The extra length of hair trimmer line will be cut into blades.

You can watch the video

A Quick Tip. Make sure that hair does not come into contact with hard objects when cutting. This contact will cut the trimmer line. And because the grass trimmer doesn’t come with this trimmer automatically, you’ll have to stop work every time, remove the spool and release the trimmer line again.

Thick hair

It is stored in the top of the grass trimmer body.

Spare spools for storage

This line for the trimmer in the reel is very easy to install. On the inner circle inside the spool. Insert the center of the hair growth mower line with the metal attachment at the top of the spool and pull the ends of the hair growth mower line along the grooves and out.

Reinforced line for trimmer

This spool is attached to the trimmer as well as the regular hair spool.

Repair ‘Gardena electric mower (changing the spool)

The guaranteed output of a factory grass trimmer will inevitably require a change in the mowing line. Having a very rough idea of how to insert the trimmer line into the grass trimmer spool on their own, beginners are reluctant to engage in this business. But with some ability, mastering this simple science is not difficult, and similar instructions below will greatly facilitate such a process.

First of all, to wind the line for the trimmer, you need to remove the spool (bobbin, spool) from the grass trimmer; certain actions will depend on the complexity of the configuration and the type of product itself:

READ Can I Mow with a Trimmer After the Rain

Small electronic grass trimmers with a working motor position and spool on the bottom, you have side buttons on both sides of the bobbin. If pressed at the same time, the top part of the spool, along with the inner m for winding the fishing line, disengages, although the bottom.

The video is devoted to the problem of changing the mowing line in grass trimmers, it will be interesting for everyone who deals with such devices. A man in work clothes appears in front of the audience and promises to immediately and at the same time detail the method of manipulation required if you set out to change or rewind the line for the trimmer.

Hero is attracted to how important it is to get a quality trimmer line first, then it will be reliable and last a long time. Then the man points out how to easily remove the old trimmer line, then he shows the very one he already has. Gonna.

How to change, remove the head of the Electronic Grass Trimmer BlackDecker GL716 when repairing, ie, change.

BlackDecker GL716 electric grass trimmer was brought in for repair. On his example, we’ll show how to remove the head, the grass trimmer head, the head of the grass trimmer, different sources call it differently. If you set out to remove the head of the grass trimmer, it must be disassembled. To do this, release the side latches, which are symmetrically located on both sides. We press two fingers there, with the other hand, gently shaking off the top cover. Take out the bobbin to wind the mowing line. We see the screw is slightly deepened in depth. Sprocket or flat socket. Holding the body of the spool with one hand, unscrew the screw counterclockwise. Swinging from side to side, pull the Mowerhead reel body only toward you. Now you understand how to change, remove.

Preparing to change the fishing line

Before changing the line, pull out and then disassemble the head. It usually includes a shroud, a spring (on some models), a bobbin with a fishing line, a cover. It is necessary to unplug the electric grass trimmer (or plug the gasoline one), and then proceed to remove the spool. It can be fixed in two different ways: in the first case, you need to completely disassemble the head, and in the second. just remove it from the gear shaft, to which it is attached.

• Under the cover is the bobbin, you must gently pull it out of the housing (sometimes a spring is hidden underneath, it should also be carefully put aside so as not to lose it);
• After removing the bobbin, the fixing bolt (or screw) becomes visible in the center of the body, which must be unscrewed in the opposite direction to the clockwise movement;
• after removing the fasteners, you must, holding the body, with a rocking motion remove the spool from the shaft of the gearbox.

The second way is as follows. The head of the bobbin is put on the gear shaft. In order to disconnect it, you need to lock this shaft. This is usually done by inserting a nail, bar or screwdriver into the hole in Champion and STIHL scythes, for example. After fixing the shaft in a stationary position it is necessary, holding the housing, start turning the head in a clockwise direction, since the thread on the shaft is usually applied to the left.

Now that the head is removed and disassembled, it is necessary to determine how thick the cord should be. You can find out the appropriate diameter for your grass trimmer by looking in the user manual or on the bobbin itself, usually such information is indicated on it. Another way is to insert the thread into the hole from which it is fed. If the twine goes without difficulty, it can be used for work.

Tip! To understand how much fishing line to wind for the spool, you need to wind it on the bobbin so that the height of the skein was not greater than the diameter of the sides. If the cord protrudes over the edges, you can’t hide the spool.

The structure of the gasoline trimmer engine for grass. Design of a gasoline grass trimmer

Numerous models of manual brushcutters on the market today, vary in power (and, consequently, in their capabilities), weight, the presence of those or other additional functions that increase the ease of use, but at the same time, the basic scheme of the device tool remains the same.

As a power drive in any gasoline trimmer an internal combustion engine is used. The cutting element. a spool with filament (fishing line) or a special blade. receives its power via a flexible or rigid shaft. The shaft is placed inside a metal bar, on one end of which the engine and fuel tank are fixed, on the other end there is a cutter head. The handle is attached to the middle part of the boom. Most often it is located keys, buttons and switches, which are used to control the operation of trimmer for grass.

Controls vary from tool to tool, but in general this includes the engine stop button, the throttle trigger for carburettor throttle control, and the throttle trigger stopper when depressed for ease of operation with large workloads.

Gearbox. 2. Trimmer head. 3. Protective cover. 4. throttle trigger stop button. 5. Switch.

throttle lever. 7. Handle. 8. Gas lever stop. 9. Boom. 10. Belt loop for carabiner attachment.

Air filter. 12. Spark plug. 13. Engine housing. 14. Exhaust manifold. 15. Gas tank. 16. Starter.

Features of self-repair of gasoline and electric trimmers for grass

Grass trimmers are simple devices for mowing the grass, replacing conventional grass scythes. This type of home appliances are powered by internal combustion engine or electricity. In the process of operation in the unit can fail some parts. Repair trimmers perform independently. At complex breakdowns order diagnosis and troubleshooting in a service center.

The easiest way to give a lawnmower in the repair, allocating a certain amount of money from the family budget, prompt and quality repair with their own hands are no less simple and convenient if you want to understand the design of the lawnmower and fix all the problems.

Mass and piece production of trimmers is based on the use of common technology, the typical design scheme consists of certain elements and parts, it is important to know them when carrying out independent repair work:

• upper part. The basis of the entire structure, where all the important elements such as the starter, carburetor and lawnmower engine are assembled;
• middle part. Hollow rod, inside it there is a rope that connects the engine and gearbox, which drives the cutting line for the trimmer. In this part there are mounts to distribute the weight of the entire structure and a belt for fixing the grass trimmer on the belt of the person who uses the grass trimmer for its intended purpose;
• lower part. The gearbox and cutting elements are integrated into the housing and are concealed under the practical cover to protect the user. The housing ensures an increased level of safety by preventing large particles of debris, stones and glass from getting into the person while operating the chain saw.

Knowing precisely the internal structure and operating principle of the grass trimmer, you can independently carry out repair measures for the structure or replace individual, worn-out nodes, using the instructions for repair.

The most common and common, self-repairable breakdowns of the machine can be called the following problems:

• engine malfunctions that cause the lawnmower not to start and not to run;
• Increased vibration of the brushcutter bar, making it more difficult to use as intended;
• increased overheating of the reducer, its accelerated heating during operation
• slow and weak functioning of the cutting line at insufficient RPM;
• clogging of the starter grid, causing the engine to overheat and stop working;
• rapid and frequent clogging of the carburetor through the use of low-quality fuel;
• clogging of the air filter if you do not take care of the unit.

All these problems can lead to the fact that the device will lose its ability to work, before ordering the necessary spare parts for the brushless brushcutter should conduct a visual inspection and diagnosis of the device.

Particular attention requires individual parts and units of the device, to check them will not need to go to a professional technician, a set of diagnostic measures will help your own hands to identify the cause of the loss of performance.

All gasoline-powered trimmers use a combustion engine as the power source. Hard or flexible shaft drives the cutting attachment. filament (fishing line) spool or special blade. The shaft is located inside a metal shaft, on one end of which the engine and fuel tank are fixed, and the cutting head is on the other end. The handle is mounted in the middle of the boom. Most often it is located keys, buttons and switches, which are used to control the operation of trimmer for grass.

Controls vary from tool to tool, but typically include a button for stopping the engine, a “gas pedal” button for throttle control, and a stop on the button when it is held down, making it easier to operate the tool if you have to do a lot of work.

Gearbox. 2. Trimmer head. 3. Protective cover. 4. Gas lever stop button. 5. Switch.

throttle lever. 7. Handle. 8. Gas lever stopper. 9. Boom. 10. Belt loop for strap carabiner.

Air filter. 12. Spark plug. 13. Motor housing. 14. Exhaust manifold. 15. Gas tank. 16. Starter.

The device of the gasoline trimmer for grass. Lawnmower design and common faults

It is easiest to give the lawnmower in repair, allocating a certain amount of money from the family budget, prompt and high-quality repair with their own hands is no less simple and convenient if you want to understand the design of the lawnmower and fix all the problems.

Mass and piece production of trimmers is based on the use of common technology, the typical design scheme consists of certain elements and parts, it is important to know them when carrying out independent repair work:

• upper part. The basis of the entire structure, where all important elements such as the starter motor, carburetor and lawnmower engine are assembled;
• middle part. Hollow rod, inside it there is a rope that connects the engine and the gearbox, which drives the cutting line for the trimmer. In this part there are mounts for weight distribution of the whole construction and a belt for fixing the grass trimmer on the belt of the person using the grass trimmer for its intended purpose;
• bottom part. It contains the gearbox and cutting elements, which are hidden under a practical cover to protect the user. The cover provides an increased level of safety by preventing coarse debris, stones and glass from getting into the person while operating the chain saw.

Knowing precisely the internal construction and operating principle of the grass trimmer, you can independently carry out repair measures for the design or replace individual, worn out components, using the repair manual.

The following problems can be called the most common and common, subject to self-correcting breakdowns of the unit:

• engine malfunction, due to which the lawnmower does not start and does not work;
• Increased vibration of the brushcutter bar, making it difficult to use as intended;
• Increased overheating of the gearbox, its accelerated heating during operation;
• slow and weak cutting line with insufficient speed;
• clogging of the starter grid, causing the engine to overheat and stop working;
• rapid and frequent clogging of the carburetor due to the use of low-quality fuel;
• clogging of the air filter if you do not take proper care of the device.

All these problems can lead to the fact that the device loses its working capacity, before ordering the necessary spare parts for the brushless brushcutter you should conduct a visual inspection and diagnose the device.

Particular attention should be paid to individual parts and assemblies of the device, to check them you do not need to go to a professional wizard, a set of diagnostic measures will help your own hands to identify the cause of the loss of performance.