Can A Punch Be Used As A Mixer
How to use the punch correctly and safely An overview of the device and the rules for using the punch. How to safely use a hammer drill, how to insert and remove a drill, how to drill holes.
The main operating modes of the punch
Perforators operate in several basic modes, switchable by the operator depending on the work being done.
Safe use of the tool
It is permissible to use the puncher only with the use of personal protective equipment. These include safety glasses, earmuffs, gloves, and a respirator. Clothes should be free of fluttering long-length elements. Hair is gathered under the headdress. Shoes should be dry, comfortable and non-slip, preferably with socks reinforced with metal plates.
The noise level of a working tool fluctuates in the region of 100-110 dB. If the treated surface resonates (for example, a concrete wall), then the noise level can reach 140–150 dB. Such sound loading can lead to medical or mental health problems. Headphones or earplugs must be used.
Removing the working tool
To remove the drill or bit after work or for replacement, you must:
- Wait until the rotation of the chuck has stopped completely.
- Pull the chuck base down until it stops.
- Remove the drill from the chuck.
- Release the chuck base.
How to insert / pull out a drill or drill
To work safely with a hammer drill, you need to master a few simple skills. Mandatory skills include installing and removing a drill, drill or any other accessory.
We hammer a pipe into the ground
Heavy perforators. Weighing over 8 kg and blowing up to 20 kJ, are used when blocking an Abyssinian well. A galvanized pipe with a sharp tip is placed vertically and, using the hammer mode, driven into the ground. Of course, the diameter of such a pipe cannot be large (up to 1 inch). But even this is enough to provide an average family with water. This method is used when constructing water intake in places inaccessible to heavy drilling equipment.
Rock drill tips
There are several rules for operating rock drills that must be followed.
- During work, do not press too hard on the tool to prevent damage to the drill. Power and performance will not increase from this in any case.
- A common mistake is the desire to perform the entire operation in full at one time. The drill needs to be cleaned periodically.
- The choice of equipment is determined by the type of work performed and the specific features of the tool itself. For example, when using one type of rotary hammer, an adapter is required to replace the nozzle, and the second has a quick-release design.
- Mechanical damage or systematic overheating of the equipment is not allowed. When choosing, you should pay attention to the models in the aluminum case, which, due to the nature of the material, always cool better.
- When working with the hammer drill, it is recommended to wear rubber gloves, which will help to dampen vibration, despite the fact that the tool itself is equipped with special inserts for this purpose.
Working with a punch in different modes
Drilling mode
It is recommended to start drilling at a low speed without pressing the surface too hard. After starting the engine, it should run in idle mode. This is necessary so that, in the event of vibrations, extraneous noise or smoke, react in time to a malfunction and prevent more complex consequences in the form of injuries, damage to building structures, complex tool breakage.
In the technology of performing work, much depends on the characteristics of the material. For example, there are often questions about how to drill metal with a hammer drill. Experts recommend using only high-quality drills that are specifically designed for such operations from trusted manufacturers. In addition, the surface must be properly prepared. The hole is made in stages with a gradual expansion of the diameter to the desired size.
Impact drilling mode (drilling)
The hammer drill has become a common designation for the drilling mode among most manufacturers of construction tools. Particular attention during the execution of work should be paid to prevent skewing of the nozzle. It is also important not to put additional pressure on the rock drill, this will not increase the motor power or speed up the work.
This function is not always used. For example, before drilling tiles with a hammer drill, it is important to turn off the impact mode and prevent the drill from sliding over the surface, which often causes scratches.
Impact mode
To work in impact mode (the toggle switch rotates to the position indicated by the hammer), special chisels are used. During operation, the perforator must be clamped with both hands. In the process, the chiseling speed can be adjusted depending on the characteristics of the work performed. It is necessary to constantly monitor the tool, since situations often arise in which the drill inside the structure stumbles upon the reinforcement. If the hole becomes full of crumbs, it is enough to remove the drill in idle mode to clean it (you can also use a construction vacuum cleaner).
Rotary hammer care tips
The service life and the overhaul interval directly depend on how timely and competently the complex of works on the maintenance of the perforator is performed. Much attention should be paid to the lubrication of the gearbox, especially if work is carried out with concrete structures, the drilling of which is accompanied by the formation of a large amount of dust.
A good protection against it can be the use of a vacuum cleaner; many models of power tools are even equipped with special devices for fixing the hose. It is also necessary to take into account that when operating at low speeds, the equipment quickly heats up, therefore, constant monitoring of the rest and work mode is required.
After the end of use and disconnection, it is recommended to clean the tool with a soft cloth from dirt. You can use soapy water if necessary. Pay particular attention to the cleanliness of the ventilation openings. It is equally important to regularly carry out preventive inspections of equipment.
Also, before starting work, it is imperative to lubricate the nozzle shanks. This is to avoid excessive stress on the drill barrel due to friction. If such work is not performed, then it can “result” in expensive repairs.