Changing the line in the AL-KO trimmer
Technical details for “AL-KO GT 4030” Lawn Trimmer with Li-Ion Battery
A powerful 40 V battery, capable of working for 60 to 80 minutes without recharging, and a cutting width of 30 cm, guarantees efficient lawn trimming over a large area using lithium-ion technology in the AL-KO GT 4030 trimmer. The time to fully charge a lithium-ion battery is approximately 90/120 minutes. This powerful free-cutter in your garden has enough energy to comfortably and accurately trim the grass in tight spots in your garden. At the same time, the flexible, 180-degree deflecting head with a cutting line is equipped with a bracket for plant protection. It provides the best cutting precision at the edge of the lawn, under bushes and near walls. With the help of automatic pressing, you can optimally adjust the length of the cutting line directly while the trimmer is working, for which it is enough to press the cutting head shortly against the ground, which automatically adjusts the length of the line. An expandable telescopic tube allows you to individually adjust the device according to the user’s height.
For your freedom: This high-performance cordless trimmer from AL-KO is ideal for gardeners who want to save time in their daily gardening tasks. Since the appliance is perceived as a whisper, you will not disturb your neighbors, and you do not have to worry about observing a quiet schedule at night, as well as on weekends and holidays.
One battery for many garden tools: The GT 4030 is part of the EnergyFlex family. If you already have other devices in the EnergyFlex family, simply install the existing battery in the “GT 4030” model. But if this is your first time purchasing the GT 4030, please order the battery and charger with it (which are not included in the basic package). Your benefit: Our 2-year manufacturer’s warranty also covers the battery for this garden device.
Note: The information on the mowing area shown here, as well as on the available operating time of the battery pack depends on the material to be mowed (height and density, grass moisture, etc.), therefore the actual mowing area and the operating time of the cordless device may differ.
Changing the line in the AL-KO trimmer
Eco-friendly trimmer, safe for humans and the environment: This cordless AL-KO lawn trimmer runs quietly and without fumes, making it the Champion lawnmower for mowing edges and corners on any lawn.
Buy “AL-KO GT 4030” and find alternatives
Cordless lawn trimmer “AL-KO GT 4030”. for precise lawn care in your garden.
The AL-KO GT 4030 lawn trimmer with lithium-ion battery from the EnergyFlex family impresses with excellent cutting results and renowned AL-KO quality. Quiet, without cables or fumes, this cordless garden trimmer will serve you faithfully in any home garden. A powerful battery, combined with a large cutting width and easy control thanks to a flexible cutting head, adjustable auxiliary handle and automatic push-down action, make it easy for you to cut accurately on any site, at any edge and in any corner of your garden.
Our advantages for you:
Our 2-year manufacturer’s warranty includes the battery warranty for this product.
Changing the line in the AL-KO trimmer
The small and compact AL-KO BC 1000 E electric trimmer is an excellent option for maintaining your home or cottage lawn. The well-thought-out design of the boom makes it easy to cut grass even in hard-to-reach places, the efficient electric motor has minimal noise and does not emit harmful exhaust into the atmosphere. The working width of the tool is 350 mm, which is quite a lot for models of this class.
Quiet and productive
The AL-KO BC 1000 E trimmer is equipped with a compact 1 kW electric motor. The engine is powered by a 230 V power supply, so just plug in the plug and get to work. The electric motor is located at the top of the trimmer, which provides improved structural balance and reduces operator stress, as well as allows you to work even in wet grass without fear of moisture entering the engine. The motor itself is equipped with built-in protection against overload and overheating, which allows to increase the effective service life of the device and prevent its premature failure. In case of overheating, the protection itself will turn off the engine, and it will be possible to resume work after 15 minutes.
The noise level of the instrument is only 94 dB (A) and complies with DIN EN ISO 3744: 2010. This is a fairly low figure, so you can not be afraid that your neighbors will express dissatisfaction with the noise during work.
Productive work tool
Despite the fact that the AL-KO BC 1000 E belongs to the budget models, it is equipped with a powerful cutting system. It is a thread-like head with a step semi-automatic line feed, which allows you to adjust the length of the line even when the engine is running. The double nylon line is 2.4mm thick and has a working width of 350mm, which is the standard for electric trimmers.
To protect the operator from waste during work, a semicircular cover made of impact-resistant plastic is installed on top of the head. Its design provides reliable protection without obstructing your view. On the right side of the cowl there is a small support wheel for more precise trimming in all positions.
Convenience at work
The AL-KO BC 1000 E trimmer is equipped with a wide shoulder strap for easy holding of the tool during work and almost completely removes the load from the operator’s hands. The rigid aluminum alloy fixed rod is curved. this design is achieved by installing a flexible drive cable that transfers torque from the engine to the head. The curved shape allows you to easily get into hard-to-reach places and expands the functionality of using the trimmer.
To increase comfort during work and improve grip, there is an additional removable D-shaped handle. The bar itself can be disassembled if necessary, which makes storage and transportation of the trimmer easier and more convenient.
Buy an electric trimmer BC 1000 E or find an alternative
Preparing for replacement
We disassemble the trimmer spool
For clarity, the mowing head (spool) was removed from the lawn mower. To replace the fishing line, you do not need to remove it, everything is done locally. It doesn’t take long.
We disassemble the trimmer spool. it rests on the latches. Remove the cover by pressing on the latches. If you do not have enough effort to do this with your hands, then use a screwdriver.
The spool consists of the following:
- Spring case
- Cover with locking latches
- Button coil
The principle of operation is as follows. By pressing the button, the spool presses on the spring and comes out of the locking grooves in the spool cap. Holding in this state, the reel can be twisted, thereby adjusting the length of the line. When the button is released, the body spring returns the coil to its original fixed state.
Disassembled trimmer spool
On the bottom of the reel there are several holes for different diameters of the lines. They may differ from trimmer manufacturer. In some cases (like here) they are signed, in others they are not.
These holes are needed to fix the line when replacing it. After winding the fishing line on the bobbin, the ends of the latter are inserted into them. This is necessary so that the scaffold does not unwind when the coil is installed in the trimmer body. In other words, it makes it easier to change the line.
Holes for fixing the line
There are models without specifying the diameter of the consumable. Then, in order to find out what the maximum diameter of the scaffold can be used, it is tried on along the holes for removing the fishing line from the trimmer spool body (see figure below).
Fitting on the holes of the line output
The reel has two line sections separated by a baffle. They may not exist. They are needed only to delimit and facilitate the winding of the consumable.
Two sections for fishing line
First, they are determined with the required length of the loess. The latter is wound into one of the sections of the coil so that it does not go beyond its limits. In this case, 3 mm was wound, the length turned out to be about 2 meters. Those. for two sections you need a 4-meter segment. this is for the 1st method. For the second method, you need two segments of 2 meters each.
Determining the required line length
Now you need to figure out which way you need to wind it. To do this, many trimmer manufacturers apply special designations to the spools, such as in the figure below.
Special designation on the reel
If no such designations were found, then you need to pay attention to the spool body. There is necessarily an arrow that indicates the movement of the mowing head. The line is wound in the opposite direction.
Bobbin case designation
Method 2. two segments
Two coiled line lengths
fundamentally no different from the method The only difference is two wound pieces of fishing line, instead of one.
The end of each segment is folded
The end of each segment is folded.
Two special fixing sockets
There are two special fixing sockets on the coil (see picture above).
We start winding the line
They hook it with a hook formed earlier on the fishing line, and begin to wind the fishing line.
Winding is carried out in a special order
The winding must be carried out in the following order: first the lower line, i.e. the one that is closer to the fixing holes at the bottom of the coil, and only then the top one, i.e. the one that will overlap the bottom section.
The bottom line is reeling
The tips are cut into the holes in the trimmer spool body. They are pulled up until they click, which means that the line has come out of the latches.
The tips are threaded into the holes in the trimmer spool body
The coil is fastened into the body. The line in the spool has been replaced.
The line in the spool has been replaced
Changing the line in the trimmer: 2 easy ways
A trimmer is a necessary and useful tool for a summer cottage and a private house. Many people own and actively use it, but not everyone knows how to replace the line in the trimmer, especially at first.
In this manual, we’ll walk through the entire replacement process step by step. Looking ahead, there are two ways to line the trimmer spool. There is no fundamental difference. the difference lies in the fact that in the first case one line will be refueled, folded in half, and in the second there will be two such lines.
The first way
Line bent in half
The prepared segment (in this case, it is 4 meters) is bent approximately in half. one segment should be 15-20 cm longer, and inserted into a special slot located on the dividing partition.
The line is inserted into the slot
The line is wound in the direction determined earlier. This is done in an interference fit, the line is neatly distributed. In this case, you need to wind a segment that is longer in the section that is closer to the button.
There are designs that do not provide for dividing the coil into two sections. This does not change anything, the line is wound in a similar way. You just need to make sure that the segments do not overlap with each other.
The first should end that section, which is located at the bottom of the coil, i.e. the one closest to the fixing holes.
This tip fits into the corresponding hole in diameter. The line is securely fixed.
The line is securely fixed
A long segment is wound another half turn. There he is similarly fixed. In this case, the segment crosses another section of the coil.
A long segment is wound another half turn
The fixed ends of the coiled line are inserted into the holes in the trimmer spool body.
The fixed ends of the coiled line are inserted into the holes in the trimmer spool body
The coil is attached to the body. The ends of the fishing line are pulled with effort so that the fishing lines previously fixed in the holes of the reel jump out from there. It is easily identified by the characteristic sound (click).
The ends of the line pull up with effort
Button spool snaps into trimmer spool housing.
Button spool snaps into trimmer spool housing
The line was changed successfully. In this case, you need to put it back on the trimmer and you can start mowing the grass.
It should be repeated, there is no need to remove the spool from the trimmer. this was done for clarity of the process of replacing the fishing line. You can disassemble the spool in place, wind it on the spool and put it back.
Line replacement completed successfully
Tips so that they do not hit the trimmer cover can and should be trimmed.
How to wind the line around the trimmer cutter head or lawn mowers
How to wind the line around the trimmer cutter head or lawn mowers
Changing the line in the trimmer: 2 easy ways
Feedback from our readers is very important for us. Leave your rating in the comments with the reasoning for your choice. Your opinion will be useful to other users.
I specially registered on the forum to say thank you for the information, maybe I can also help you with something.?
I want to orient myself when choosing only to my taste. There are no other criteria for the music posted on this page. Something in my opinion is more suitable for morning listening. Something. for evening.
I can recommend that you visit the site, which has many articles on this subject.
You’re not right. I’m sure. I can prove it.
Not bad, I liked it, but I thought it was the best.
I am ready to place your link on my website, I really liked your material.
MAINTENANCE TRIMMER. LINE TOPPERS AL-KO
It is a pity that I cannot participate in the discussion now. I don’t have the information I need. But I will be happy to follow this topic.
cool. I’ve been waiting for him for a long time.
Great, this is funny information.
Quite right! I think this is a good idea. And she has the right to live.
I fully share your opinion. This is a good idea. I am ready to support you.
original and useful!
Congratulations, what a great answer.
Until what time?
There is a site with a huge amount of information on a topic of interest to you.
portable trimmer; electric motor (450 W) from mains cable; cutting width: 30 cm; included: fishing line; weight: 2.9 kg
Trimmer Al-Ko GTE 550 premium. useful tips for work and a visual aid. how to replace the fishing line. Duration: 9:20. Electromax.com.ua.
Review of the AK-KO BC 4535 lawn mower
Add comment Cancel reply
- (the black)
- one hundred
- DVD player
- Falcon eyes
- Pro sKit
- TV tuner
- VoIP phone
- Wi-Fi router
- Acoustic system
- Audio cable
- Video camera
- Flush-mounted kitchen sink
- Integrated amplifier
- Infrared heater
- USB cable
- Balanced audio cable
- Coaxial cable
- Microphone cable
- Chimney hood
- Computer case Black
- The envelope
- Bracket to wall
- Media player
- Weather station
- Music Center
- Storage device
- Storage water heater
- Wrist Watch
- Board game
- Optical Drive Black
- Air purifier
- Power supply
- The tablet
- a printer
- Remote controller
- The size
- A pen
- Alcohol mashine
- Cooling system
- Split system
- A bag
- TV set
- Flash drive
- The black
- Sewing machine
- Manfrotto tripod
- Electric shaver
Changing the line on a trimmer or lawn mower
Changing the line on the trimmer
To replace the line on a trimmer or lawn mower (cord, strings), first of all, you need to know its thickness. If the remnants of the cord have not survived, then we study the passport of our garden equipment. Sometimes the information you need can be found by carefully examining the mowing reel, a range of diameters can be applied to its surface. If our searches were unsuccessful, then we simply estimate the diameter of the outlet on the coil. The line should move effortlessly in it. I do not recommend widening the holes in order to use a thicker string to increase productivity and the possibilities of gardening equipment. Line thickness is calculated by the manufacturer based on engine power.
To replace the cord on most models, it is necessary to disassemble the mowing reel by pressing the latches. Sometimes, simultaneously with pressing the latches, you also need to turn the upper part of the coil.
A standard bobbin is loaded with 5-6 meters of thin cutting line or up to 3 meters thick. Figures are approximate, depending on the size of your mowing head. If it overheats during the mowing process, it is best to use less line. There is a chance that it will be baked, and you will simply throw it away.
In the simplest trimmers and lawn mowers, there is a non-automatic reel with one tendril. Everything is simple there, we fix one edge of the line in the slot inside the bobbin. Then we wind as much cord along the arrow as will fit under the protective casing. We bring out 10 cm of strings through the holes in the protective casing and the coil and assemble it.
Non-automatic reel with one tendril
Semi-automatic single section reel with 2 antennae
Semi-automatic two-piece reel with 2 antennae
If the line on the trimmer has 2 antennae, then before winding the string is folded in half, shifting the edges by 5-10 centimeters. Bobbins come in a variety of designs, but each has some kind of hook to secure the middle of the cord. If the bobbin is one-piece, then there is a hole where you need to thread one end of the line and center it again. There is a cutout in the baffle in the two-piece coil.
Wind-cord and winding direction arrow
The inscription “Wind kord” and an arrow show us the direction of winding. If there is no arrow, then we wind in the direction opposite to the direction of rotation. With one hand we hold the edges of the cord, and with the other we rotate the bobbin, winding the line, each side on its own path. We lay the string tight enough, ideally exactly unnecessary, the main thing is to prevent intersections. She herself, at work, will take the right place. When 10 centimeters remain, we fix the edges in the slots. We pass the string through the holes on the coil body. Alternately, lightly twitch the line so that no loops form inside, and insert the bobbin into the spool. Then we assemble the mowing reel. Sometimes there is such a design of the coil that when collecting it, the edges of the string must be freed from the slots in the bobbin. You can check the correct assembly of the semi-automatic head of our garden equipment by simulating the tapping of the trimmer on the ground. Press the button in the center and at the same time pull the edges of the line. If everything is in order, the antennae are slightly extended.
On Oleo-Mac lawn mowers, the cutterbar does not need to be disassembled at all. We just pass the string through the holes. We center it, and by rotating the lamb in the direction of the arrow, we wind the cord. Changing the line on the trimmer is very fast, this design is becoming more common.
I hope you find useful the article on the correct selection of fishing line for your garden equipment “Trimmer line, string, cord for electric and lawn mowers”.
Video how to wind the line around the trimmer cutter head or lawn mowers with one or two pieces of line:
Storage space for spare coil
It is very simple to install such a fishing line into the reel. according to the internal scheme inside the reel. We insert the center of the line with a metal mount in the upper part of the reel, and draw the ends of the line along the grooves and bring it out.
It is stored at the top of the trimmer body.
Trimming the line into the trimmer.
I want to devote today’s article to the sore subject of summer residents and gardeners of the entire post-Soviet space “How to fill the line in the trimmer.” Not many trimmer manufacturers answer this question in their instruction manuals. Therefore, it is also difficult for simple gardeners to figure out how to do it correctly.
I want to start with a brief description of the technical characteristics of the trimmers.
So, trimmers are electric and gasoline. The cutting element for trimmers can be a line and a knife. The line is ordinary, four. pentahedral and intertwined (in the form of a pigtail). Knives come in 2, 3 and 4 bladed knives. Knives also come in plastic and metal.
The line feed system from the trimmer is manual, semi-automatic and automatic.
The development engineers who create new models of trimmers accurately calculate the diameter (thickness) of the line and the number of knife blades, according to the power of the trimmers. Otherwise, the engine is overloaded, resulting in damage to the engine. And these are additional and significant costs.
Trimmers on the market today:
With one nozzle. only a line.
With two nozzles. a fishing line and a three-four-blade knife.
With one nozzle. only three to four blades.
Our Kulibins have long ago learned to improve any mechanisms. So, for example, some gardeners make successful, in their opinion, replacement of fishing line with a metal cable, or fishing line. But at the same time, they do not think about the safety of their own and their loved ones, because, like a cable with the power of a working trimmer, it can easily break out and not only injure the mower and others, but leave him crippled for life. Using a fishing line can and gives a better effect, I have never personally tried it than a trimmer line, but such work has a number of inconveniences: when it comes into contact with hard objects, it loosens or can simply be pulled out of the reel without limit.
So, what is called closer to the topic. Here is an example of how to thread the line into the trimmer (Trimmer BOSCH Art 30). Everything is very simple. Started.
After you have chosen the line for refueling, you need to cut off the required amount of line, because all the line in a skein will not be wound into a reel.
Cut off and start reeling.
Remove the coil and the protective cover from the coil.
They took it off. We fix one end of the line in the gap and carefully and evenly wind the line.
The amount of line should be such that the protective cover of the reel closes and the line on the reel unwinds a little by itself.
We put the other end of the line into the hole on the protective casing.
Next, we take the coil and the protective cover of the coil. We squirt the end of the line from the reel into the metal hole on the reel’s protective cover. Tighten the line a little.
We put it all on the trimmer. Turn the coil clockwise until it clicks.
They fixed it. Now we connect the trimmer to the network. We put the trimmer in the starting position for work. We turn on the trimmer. Excess line length will be cut on the trimming blade.
Coil in trimmer
That’s all we start to work.
In addition to the standard lawn line, my trimmer also has a thick line for cutting rough weeds. It has the shape of a pigtail, i.e. three lines are tightly intertwined. This line has its own spool.
Heavy-duty line in a reel
Such a reel is attached to the trimmer in the same way as a reel with an ordinary line.
In order to change the line, you need to remove the old one (if it was).
The reel is the part of the trimmer structure that is located inside the mower head, drum or bobbin. Heads may vary depending on the manufacturer. But this article only covers Patriot, although their mechanism is used by many other companies.
Now you need to understand how to properly remove the head from the trimmer and how to pull the drum out of it.
Instructions on how to unscrew the manual head on the trimmer are described below.
- First of all, you need to clean the head from dirt and adhering grass, if it is dirty. To do this, lift the mower head up and, grasping the casing, remove the special protective cover on the drum.
- The next step is to remove the spool from the drum. The reel can be easily removed even with one hand, because it is not fixed in any way inside the drum.
- The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with the spool, while unscrewing the screw counterclockwise.
- Now you can pull the coil out. As mentioned above, it is not secured by anything, except for a hook with a metal shaft, so it does not need to be pulled out with force. Carefully, in a circular motion, pull the spool out of the drum.
- Now it remains to remove the old fishing line and follow the following instructions.
Installation of the spool and drum in their original place is performed according to the reverse algorithm.
Before threading the line, make sure you have purchased the correct thread for the trimmer. In the event that the thread is not suitable, the consumption of fuel or energy increases, as well as the load on the engine of the lawn mowers.
In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m of line. The specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the spool itself. If you cannot accurately determine the length, you can do the following: insert and wind the thread until the coil is fully charged (the line level will be compared with the protrusions on the sides of the coil). It is necessary to ensure that the line sits evenly in the reel.
Do not forget that thick thread will be shorter than thin thread.
The instructions for threading the line into the spool are described below.
- The prepared thread must be taken and folded in half. It should be ensured that one edge is 0.1-0.15 m longer than the other.
- Now you need to take the ends in different hands. The one that is smaller must be pulled up to the larger one so that it becomes 2 times shorter. When bending, maintain an offset of 0.15m.
- Find the notch inside the coil baffle. Carefully pass the loop you made earlier into this slot.
- To continue working, it is necessary to determine the direction of winding of the thread in the bobbin. To do this, it is enough to inspect the coil. there should be an arrow on it.
- If the arrow-pointer could not be found, then it is quite possible that there is a written designation. An example is shown in the photo below. It is necessary to inspect the coil head. There is a direction indicator on it. However, this is the direction of travel of the coil. To get the winding direction, you need to wind in the opposite direction.
- Now you need to load the spool with line. It is worth noting that there are special guide grooves inside the coil. Follow these grooves when winding the thread, otherwise the trimmer may be damaged. At this stage, you need to charge the coil very carefully.
- When the user winds almost the entire thread, take the short end (do not forget about the 0.15m protrusion) and pull it into the hole located in the wall of the reel. Now you need to repeat this action in the same way with the other end (on the other side).
- Place the reel itself in the head of the reel, before that threading the line through the holes inside the drum.
- Now is the time to put the drum back in place. After that, you need to take the ends of the line with both hands and pull them to the sides. Then you need to put the lid back on (here you can safely make efforts until you hear a characteristic click).
- Remained to do the “cosmetic work”. We need to see if the thread is too long. You can start the trimmer and check in practice if everything is comfortable. If the thread comes out a little long, you can cut it with scissors.
How to wind the line onto the Patriot trimmer reel?
Almost every beginner when using a trimmer is faced with the problem of changing the line. While it is very easy to change your line, you need to learn how to do it correctly. Changing the fishing line with proper skill will take no more than five minutes. you just have to constantly practice it. This article will look at changing line using Patriot trimmers as an example.
Although winding the line is a very simple task, many beginners can wind the line incorrectly. Below are the most common mistakes.
- Many people, when measuring a thread, think that 4 m is a lot. Because of this, people often measure less and therefore lack line. Do not be afraid to measure out a lot, because you can always cut off the excess.
- In a hurry, some people do not follow the threading grooves inside the spool and wind the thread randomly. This will cause the line to come out of the reel and may even cripple.
- For winding, use only the appropriate line. This mistake is the most common one. You need to monitor not only the thickness and volume of the line, but also its type. You should not use the first line that comes across for wrapping, which will not meet the goals. For example, you do not need to use a thread on young grass if you need to mow dead wood.
- Do not turn on the device until it has been fully wound and collected. Although this is obvious, some people do this in order to check if everything is done correctly.
- In no case should you confuse the direction of refueling, as this will overload the engine, and it will soon come out of working condition.
It is quite common for beginners to make mistakes, so you need to follow the tips given in this article.
See below for how to replace the line on the Patriot trimmer.
What types of woods are there
The most common type of line that fits almost all reel types is round cord. This is an ordinary fishing line, suitable for mowing succulent grass, but it will be much more difficult to mow dead wood with it, and even more so it will not cope with bush.
As a rule, the diameter that can be used to cut young grass does not exceed 1.6 mm. The thicker the thread, the more coarse grass it is able to overcome.
There are fishing lines with sharp edges in the form of an asterisk or a square, this option is more adapted to mowing dry grass precisely due to the existing sharp edges, but its disadvantage is greater wear and tear and it is inferior in strength to a round cord.
There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but it is used only on lawn mowers, since the exit of such a thread from the spool is difficult, it is used most often with discs into which segments are inserted. The disadvantage of such a product is its fragility.
Most often in gasoline trimmers with an engine with an output of more than 1.5 hp. use cords with a metal cable inside.
This thread is ideal for cutting dry grass and small bushes. The presence of a core has a positive effect on the wear resistance of this material.
The disadvantage of such a cord is its price, which is significantly higher than the listed opponents.
How to change the line in the trimmer and which one is better to choose
Since we considered the choice of a trimmer in the previous article, today we will tell you how to properly fill the trimmer with fishing line, and which one is better to choose based on the working conditions.
After you bought a trimmer and began to actively use it, sooner or later the question of replacing the fishing line will arise, since this is the most wearing element in the tool, intensive use of the trimmer will lead to frequent replacement of consumables.
How to remove or tuck the line into the trimmer
In order to wind the line, it will take about 10-15 minutes. What is a trimmer coil? Plastic body with a cassette inside, on which there is a special hook for easy winding of the fishing line.
Almost all trimmer reels have a similar fastening principle, this is a central screw-button, when pressed, it becomes possible to pull out the line of the required length. The photo below shows a few examples of different trimmer spools.
The bobbins of the trimmers, the motor of which is located at the very ground, have a different attachment to the axis of rotation, they have two buttons on the spool located on the sides that need to be wrung out, otherwise the replacement of the thread is no different from other cassettes.
The principle of correct winding of the fishing line is similar in all of the above cases, therefore, for example, consider the standard version with two antennae.
To remove the spool with the fishing line, you need to unscrew the centrally located screw, but note that the thread is left there, so you will have to turn it clockwise, this was done on purpose so that during operation it does not open under the influence of centrifugal force.
Next, using a screwdriver, disassemble the head and remove the spool onto which the fishing line is directly wound.
Having measured the required length and folded in half, you need to tuck the fishing line into the spool, eventually bringing its ends opposite each other (for this there are special slots for fixing).
After that, it is necessary to assemble the head in the reverse order, threading the ends of the cord into two corresponding holes.
If you have doubts or it is not entirely clear how to load the line on the trimmer, we recommend that you look at how to properly wind the line into the lawn mower.
In this video, in detail, step by step, the instructor will open the trimmer head, measure the required amount of line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.
Exchange and return is carried out within 14 days from the date of purchase in accordance with the Law of Ukraine “On Protection of Consumer Rights”
Trimmer AL-KO GTE 450 Comfort
|Bevel width||30 cm|
Go to full description
|Delivery:||– in Kiev FAST, FREE|
– within Ukraine 1-2 days, FREE
|Payment:||possible upon receipt|
|Exchange / return:||within 14 days|
Official guarantee. 2 years
Kosilka. official representative of AL-KO on the territory of Ukraine
Description trimmer AL-KO GTE 450 Comfort
The AL-KO GTE 450 Comfort Comfort trimmer is perfect for cutting grass on lawns, backyards or in the garden. The compact and reliable device has earned a high reputation for long service life and quality performance.
The AL-KO GTE 450 Comfort trimmer is primarily characterized by a robust 450 W electric motor. Due to the overhead position of the engine, the model is perfectly balanced, fits comfortably in the hands of the operator and does not put stress on the shoulders and arms during prolonged work. It should also be noted that the trimmer operates from a 220 W network, the engine is protected from voltage surges, overload and overheating.
The AL-KO GTE 450 Comfort trimmer has a telescopic handle that allows you to quickly adjust the device to suit any operator’s height. For the convenience of work, the designers have provided an additional adjustable handle. All trimmer controls are intuitive and simple, therefore this model is in great demand among many consumers of the Ukrainian market.
The AL-KO GTE 450 Comfort trimmer uses a double nylon line as a cutting element. The grass bevel is 30 cm wide, and the line is fed by a semi-automatic trimmer head. Considering the low weight of 3.0 kg, we can confidently characterize the tool as an indispensable assistant for working on caring for a summer cottage or garden plot.
Trimmer AL-KO GTE 550 Premium
Swivel trimmer head:
- AL-KO GTE 550 Certificate
- AL-KO GTE 550 Warranty Card
- AL-KO GTE 550 trimmer instruction
- AL-KO GTE 550 Certificate
- AL-KO GTE 550 Certificate
- AL-KO GTE 550 Certificate
- AL-KO GTE 550 warranty conditions
- AL-KO GTE 550 electronic warranty card
The basis of the AL-KO GTE 550 Premium electric mower is a 550W motor with a lower position on the boom. This arrangement made it possible to balance the load during operation, without creating inconvenience during control. The use of an electric motor is always more economical and environmentally friendly, since there is no need for special maintenance, and there are no exhaust gases harmful to nature. You don’t feel attached to the mains thanks to the long power cord and a special anti-entanglement locking system. With the 180 ° cutting head you can easily trim edges. for a perfectly manicured lawn). The telescopic aluminum bar and the pivoting part of the handle ensure the optimum length and position of the trimmer, thanks to which the trimmer can be adjusted quickly and easily.
For high-quality cutting of grass in areas of any shape and complexity of the electric mow, the AL-KO GTE550 Premium uses a swiveling flexible thread head with a protective shield. The cutting head can be rotated 180 degrees and can be tilted in three positions. This flexibility increases the trimmer’s maneuverability and performance many times over. The grass is cut by the double line made of durable nylon integrated into the trimmer head. The fishing line is in a special reel, from which it is fed with the help of step automation. The robust construction and quality materials in the trimmer ensure long, uninterrupted operation for a lifetime. Thanks to the shackle and support wheel, it is very easy and safe for plants to trim the lawn while mowing under bushes, along walls and fences.
Uniform load distribution
The well-thought-out design of the electric scythe is created with the condition of uniform distribution of the load throughout the body, which is facilitated by the lower placement of the engine, the curved main handle, the ability to adjust the length of the rod and the inclination of the control handle for comfortable control by the user.
Low noise motor
One of the advantages of using electric motors is practically silent operation and no harmful effects of exhaust gases. For a 550 W electric motor, it is easy to work for a long time without stopping or refueling, which saves time and increases productivity. With its help, the fishing line comes into motion, which produces a cut.
Semi-automatic cutting element
The trimmer uses a reel with a double nylon line of high strength and durability, which works according to the technology of step automation, as a cutting element. Replacing a used line with a new one is done by hitting the ground a little with the reel without having to turn off the engine.
Head tilt adjustment
The ability to change the angle of the trimmer head allows for a neat haircut in the most difficult to reach places, such as under a garden bench or swing. Rapid tilt changes from vertical to near-horizontal significantly increase productivity and workflow efficiency.
Rotate 180 degrees
The ability of the thread head to rotate 180 degrees around itself increases its functionality and maneuverability. This flexibility enables precise and neat trimming at the very edge of lawns or near a variety of obstructions such as fences, trees, bushes and other plants. The bail and support wheel further aid in precise trimming. A protective cover on the cutting system prevents breakage of crops and protects against flying debris.
Telescopic boom system
The aluminum bar is equipped with a telescopic system, which makes it possible to adjust the trimmer height to suit the operator’s height. In addition, the boom can be disassembled for transportation and storage without inconvenience. By changing the tilt of the control handle and the height of the boom, you can choose the optimal position for the greatest convenience during operation.
Thermal overheating protection
In the event of prolonged operation of the engine and overheating, the built-in thermal protection device with a heating sensor is triggered, which, when the permissible value is exceeded, disconnects the trimmer from the power supply, preventing damage. To restart, the motor must be cooled. In case of power surges, the breakdown is prevented by the built-in overload protection, which also turns off the motor. Provided security systems ensure reliable performance for the entire service life.
electric trimmer AL-KO TE 450
- Question answer
|Type of food||from the network|
|The weight||2.9 kg|
|Engine power||450 watts|
|Engine displacement||cub. cm|
|Fuel type / fuel tank volume||l|
|Cutting system||double nylon line|
|Cutting width with a knife||30 cm|
|Adjusting the cutting height||not|
|Line cutting width||cm|
|Infinitely variable speed control||not|
|Line feed||step automation|
|Line diameter||2.4 mm|
|Number of knife blades|
|Folding handle||there is|
|Height adjustment of the handle||there is|
|Swivel mowing head||not|
|Tilt angle adjustment||not|
An easy-to-use, powerful and reliable trimmer. It will help to tidy up the lawn without any problems, or a suburban area of medium size.
- The electric motor in this braid is located at the bottom.
- During operation, a power of 450 watts is achieved. For safety reasons, work with this trimmer model is possible only in dry weather and in the absence of dew on the surface of the grass.
- The mowing strip is 30 centimeters wide.
- The cutting element in the AL-KO TE 450 trimmer is a double nylon line, which is automatically fed directly during the work with small jerks.
- Once the entire coil has been used up, it can be easily and safely renewed. For quick change, a spare bobbin is attached directly under the handle.
- With the trimmer of this model, you can mow productively for a long time without getting tired, thanks to the height-adjustable telescopic handle.
Among all the advantages of this trimmer, it should be noted its low weight. only 2.9 kilograms.
The manufacturing company provides a one-year warranty for the unit.
Electric scythe AL-KO GTE 350 Classic (Optional: spool)
ELECTRIC MOTOR WITH A POWER OF 350 W
THE POSSIBILITY OF MOWING THE LAW IN RADIOUS AREAS
CUTTING UNIT WITH WIDE GROOVE
The practical and easy-to-use electric trimmer AL-KO GTE 350 Classic has a powerful motor that is powered directly from the 220 V power supply. With this power supply, you are guaranteed to get rid of the exhaust gases typical for lawn mowers with internal combustion engines. This is an environmentally friendly and convenient engine option that ensures uninterrupted trimmer operation. Another important characteristic. this is a low noise level, which contributes to comfort when mowing the lawn.
Due to the compact size of the cutting head and mobility, the AL-KO GTE 350 Classic is ideal for cutting grass in the most inaccessible places: border edges, complex flower beds, low bushes. All these landscape forms you can easily handle with this electric scythe. The presence of a protective wheel prevents the impact of the cutting part when mowing, so you can cut the grass in the immediate vicinity of walls or fences.
The AL-KO GTE 350 Classic trimmer features a durable double nylon line for cutting. It easily cuts grass and plant stems when starting the semi-automatic filament head. The grip width of the line is very large. as much as 25 cm, which is optimal for a hand trimmer.
The AL-KO GTE 350 Classic electric scythe motor is located directly at the bottom of the device. It is well protected by a casing and disc-protected, easy to start with a push of a button on the handle, and ready to go in a matter of moments.
The AL-KO GTE 350 Classic trimmer is very easy to operate. You don’t need surgical precision to cut excess grass without damaging the plants you have carefully planted on your lawn. The support wheel and the protective arch installed above the cutting part of the electric scythe will perfectly cope with this.
Ergonomic D-shaped scythe handle. very convenient for work. It fits perfectly in any palm and provides a secure grip. The rubberized cover of the handle will prevent your hand from slipping during mowing and will provide you with safe working. In addition, the rubber dampens engine vibration well, which contributes to a comfortable work of the operator.
For the GTE 350 Classic electric scythe, AL-KO has selected exceptionally high-quality materials: strong steel for the bar, reliable plastic for protection, nylon line of increased resistance. for the cutting part. All materials have been certified and meet European quality standards.
Electric scythe AL-KO GTE 550 Premium (Optional: spool)
ELECTRIC MOTOR. SOLUTION FOR MODERN PEOPLE
ACCESS TO MOWING IN DIFFICULT SPACES
STRONG NYLON LINE
The AL-KO tool motor has a power of 550 watts. It is able to easily handle small lawns. for such an engine, an area of 300 sq.m. this is the optimum value for continuous operation. The engine operates using a conventional electrical network. just plug it in. Also an electric motor. it is highly environmentally friendly and easy to handle.
How does a trimmer differ from a standard mower? The ability to carefully handle hard-to-reach places! And it is this quality that is fully realized in the Al-KO electric scythe model.You can easily process the lawn at its edge, remove excess grass from the pedestal of a gazebo or bench, work out flower beds with plants of complex shapes.
The AL-KO GTE 550 Premium trimmer uses a strong line as a cutting edge, which can easily cut the thickest and strongest plant stems. The 1.6mm line is made of nylon for durability. It will not tear even with intensive work and will provide a neat cut of grass in all areas.
The AL-KO GTE 550 Premium grass trimmer uses the latest technology. In particular, its motor is located on the lower part of the boom, which makes it possible to balance the load when working with an electric scythe. Also, even distribution of the load is ensured by means of a curved handle, the inclination of which can be adjusted.
In order to cut the grass with a trimmer, you can adjust the design of the AL-KO GTE 550 electric trimmer to your height and size. The foldable telescopic bar allows you to easily handle the lawn, adapting to your height and build. Light weight and convenient handle adjustment will allow you to adjust the mowing to your needs in a matter of minutes.
Getting started with the AL-KO GTE 550 trimmer is effortless. Everything you need to mow your lawn. it is access to the power grid. The engine starts up instantly and you can start treating the lawn in a matter of minutes, without worrying about how long it takes to warm up the engine (as is usually the case with an internal combustion engine).
Rubberized handle of this model. one of the most comfortable in its segment. It has a comfortable shape that is easy to grip with the palm, as well as a practical rubberized surface that does not slip when the trimmer is in operation. Also, the rubberized handle dampens vibrations well and does not cause inconvenience in work.