Cleaning Air filter of a trimmer for grass Patriot. Fuel filter for a trimmer for grass…

Cleaning the air filter for a trimmer for the grass Husqvarna 128r

Useful material from which you will learn how to get a capricious gasoline trimmer for grass that does not want to work!

The summer time has come, and in the personal plots habitually hidden the lawn mower. Great tool, powerful and mobile. Using a gasoline trimmer for grass and grass, you can mow, and get rid of a dried.up weed. However, there are cases that the lawn mower does not start, works with interruptions or without developing full power. Of course, no one is at work! And as they say, you twitch the laborer’s handle more than the mowing.

Difficulties with the launch do not only have the types of motorcycle, but also in new. How to be in this situation? There is only one way out. to listen to the advice of experts and take advantage of their practical experience!

If you put a cable instead of a fishing line, without the possibility of its release, reliably fixing the two ends of the cable and cutting them with welding (a drop of melted metal holds the cable from blooming). Grass such a tool “falls” at a time. The shoot is cut off about a finger with a thickness. Stones are not as afraid as disk. There is true, the problem: when wear, pieces of cable threads break off, and these twisted wires remain in the place of mowing. If you step on them, you can get hurt.

But pieces of the cable remaining on the field are half a bastard. The fishing line for the trimmer, breaking off, weakens the dynamic blows to the transmission and the engine, the cable does not give such an opportunity. Result of quick wear of motorcycles.

Also, the ignition coil can be broken in electrical equipment. In this case, the lawn mower will not start or start and works with interruptions, and then stalls, or “hot” does not start at all.

You can check the serviceability of the coil in the same way as when checking the spark: we unscrew the candle, lean it against the trimmer body for the grass. If there is no spark with a jerk of the starter, or it appears through time. you need to change the coil.

Review of models

Gasoline braids for grass are widely used for professional laws care, as well as in agriculture. These samples of modern technology have proven their effectiveness when leaning weeds and hay harvesting

In such conditions, special attention is paid to the correct choice of the representative of the model range, taking into account the design characteristics and technical characteristics

At the moment, potential customers are offered the following models of the STIHL motorcycle:

To describe the main features of representatives of these categories, it is worth considering some samples of technology. So, the light lawn mower FS-38 is designed to perform simple landscape work, as a rule, in the conditions of personal plots. The weight of this tool is a little more than 4 kg. In this case, the operating volume of the engine and its power are 27.2 cm3 and 0.65 kW, respectively.

The main advantages of representatives of this category include the following operational indicators:

• insignificant weight;
• maximum ease of use;
• minimum fuel consumption;
• power plant power;
• reliability and long service life;
• minimum noise and vibration;
• modern design.

One of the popular models related to the segment of powerful trimmers is Stihl FS-13. The “heart” of this six.kilogram braid for the grass was an engine with a volume of 36.3 cubic centimeters and a power of 1.4 kW. The model is equipped with a tank with a volume of up to 0.5 liters. Powerful lawn mowers, as a rule, are classified as professional tools with the following advantages:

• increased power;
• maximum reliability and durability;
• the possibility of processing almost any surfaces, including thick shrubs;
• convenience and ease of operation;
• the presence of a “bicycle” holder handle.

How to remove and serve a filter for a trimmer for grass

A trimmer for grass is an indispensable thing on a garden plot. If you want to support the beauty of lawns in the country, a trimmer for grass will help to quickly cut grass with minimal efforts.

Like any other equipment, it needs gentle operation. First of all, it is necessary to replace the fuel and air filter in a timely manner.

At the same time, it is completely optional to give equipment to the service. any.

Types and principle of the filters for a trimmer for grass

In modern motorcycles, two types of filters are used. fuel and air.

Even the highest quality fuel has various additives that quickly accumulate and disable the technique.

The task of the fuel filter in gasoline trimmers is to protect the device engine from various impurities contained in gasoline and oil.

Outwardly it is very small in size. Make it from felt material. A compactly folded felt manufacturer placed in a metal tip and has on a fuel tank on a fence tube.

Another placement option is in the highway between the carburetor and the tank. Many owners of trimmers note even excessively thorough cleaning, so the material is quickly clogged so much that it requires a complete replacement.

Its main purpose is to keep the dirt and dust entering a trimmer for grass grass during operation.

With mowing, not only dust rises into the air, but also a small SOR, crushed grass, which can quickly clog the technique. A good filter will prevent engine breakdown, even if the air is very contaminated.

The place of its location can vary depending on the model of the trimmer for the grass, but is usually located on the side of the device under the protective casing.

The casing is fixed either on a bolt or latches, which are very easy to open to remove the contents. The filter itself can be made in the form of a ring or plate of foam, felt, fleece.

If you mow on average 1-2 times a week, then it will be enough to replace at least once a year. With more intense use, check and replacement should be carried out more often.

How to clean a filter on a trimmer

Sooner or later, there will be a need to rinse the air filter of a trimmer for Husqvarna grass or any other manufacturer. There is nothing complicated, and you can remove pollution from it yourself a couple of hours before mowing.

• Unscrew the bolt on the protective casing or squeeze the latches.
• We take out the filter and inspect. To remove all accumulated oil and other pollution, gasoline will be required.
• We water the gasoline from the canister to the contaminated filter and wash off all the oil. Squeeze and leave to dry for at least 2 hours.
• We wipe the installation site with a cloth moistened in gasoline.
• Set everything in place and close the casing.

Instead of gasoline, you can use soapy water, but it removes dirt still not so effective.

As an alternative to flushing, you can advise blowing or just shaking the litter. These options for cleaning are suitable if there is no oil pollution.

Is it worth buying

Buying motorcycles is determined by what purposes it will be applied. If you need to cut the lawn and remove weeds in a small area near the yard or in the garden, Chinese lawn mowers will fully cope with this task. In a short period of time, they will not overheat and provide comfortable work.

If you look closely for a professional option for direct work for about 8 or more hours, the Chinese manufacturer will not work

Pay attention to professional equipment with higher indicators and production capacity. Motokos needs to be purchased responsibly, because the service life largely depends on the quality of the equipment

So that the unit serves you as long as possible, follow the rules for using the device

Motokos needs to be purchased responsibly, because the service life largely depends on the quality of the equipment. So that the unit serves you as long as possible, follow the rules for using the device.

The continuous operation of the lawn mower is indicated in the instructions of the trimmer for the grass. On average, kosim for 15-20 minutes, after which we mock a trimmer for the grass and let it cool for 3-5 minutes. Also, weather conditions provide for the duration of continuous work. In hot weather, when mowing high grass, thickets of weeds, under a large load, the trimmer for the grass overheats faster.

Many problems with motorcycles arise due to improperly prepared fuel mixture. In two.stroke engines, lubrication is produced by special oil (not ordinary motor!) mixed with gasoline. If the oil is not mixed with gasoline, then the lawn mower will quickly fail. Oil/gasoline is mixed in the proportion indicated in the instructions of the trimmer for grass. This is usually 1:40 or 1:50.

The question often arises: 1:50 proportion is how much oil and gasoline?

The numbers mean the following: fifty parts of gasoline are taken per part of the oil. Hence: 1000 ml (1 liter of gasoline) we divide by 50, we get 20 ml, that is, 1:50.

Thus, you can calculate the composition of the fuel mixture (gasoline/oil) in any proportions. To add oil to gasoline, not “by eye”, you can advise you to take a medical syringe with 20 ml, dial it in it and “inject” into the container for the preparation of the fuel mixture.

A small amount of oil mixed with gasoline leads to increased wear of the cylinder.piston group. An excess of oil in the mixture, although not so fatal, is also harmful. Cooking piston rings, rapid formation of soot in the combustion chamber, and a drop in engine power may occur. In addition, the mesh screen of the muffler is closed. Therefore, some users (after the end of the warranty period for a trimmer for grass) recommend it to be dismantled.

How to change the starter cord?

It happens that in the impossibility of starting a starter is not a spring to blame, but the cord itself. He can seize or completely break. Dismantling the starter of the lawn mower or trimmer for grass is universal in its steps.

• Remove the starter block from a trimmer for grass or lawn mower.
• Unscrew the main bolt holding the handbrake.
• Pull the coil and melt the remains of a worn cord from it.
• Unscrew the knot on the handle of the cord and pull its end from it.
• Untie the knot at the other end (at the beginning of the coil) and remove the old cord. The nodes that have become tight are unleashed with pliers or ticks.
• Tie a knot on one of the ends of the new cord, prone it through the hole at the beginning of the coil (closer to its axis).
• Shin a few turns of a new cord to the coil. If it is long, then cut the excess.
• Season and soak the spring tensioner (if it starred) and spring.loaded elements in the correct sequence.
• Put the coil in place and take the free end of the cord to the outlet of the starter and in the handle.
• Install the starter block in place.

Twist the starter by the cord, start the engine of the lawn mower or a trimmer for grass. The larger and more powerful the engine, the more cord jerks will be required when starting, the norm is no more than 7 times. The result is a quick and smooth launch of the motor, the readiness of the unit for work.

Repair of the starter of the gas trimmer for grass may be needed at the most inopportune time. At the same time, there are two ways to solve the problem: replace a broken part or replace the entire assembly. The last option will cost more. In most cases, only a screwdriver with a tip is required to repair the device with your own hands. Repair does not take much time and does not require special knowledge. To achieve the desired positive result, it is enough to know the device, the principle of operation, the nuances of the assembly-disassembly of the starter for the trimmer for the grass.

The device and principle of the starter on the trimmer

Gas engine. This is mainly the main part of the brush. Its power lies in the range of 0.5-2.5 liters.With. Movement from it is transmitted to the shaft located inside the hollow rod, and then through the gearbox, consisting of gears, already stabbed or knife (working body).

Bigorezes also have the following elements:

• Corrugated board;
• lever arm;
• belt designed for simplicity of use;
• Starter used to launch an internal combustion gasoline engine.

The starter of the trimmer for grass is an integral part of the engine start. This is shown separately in two photos below.

Starting mechanisms for different models of gasoline braids work according to the same principle: when starting an internal combustion engine, the tongues indicated by the number 1 in the photo above are hooked by dogs 3. When the engine is launched, they return to the previous position due to centrifugal force. A similar role is played by wires 2.

The process of returning to the initial position of the elements of the mechanism is due to the presence of a spring wound around the axis. It turns around when the rope is pulled. After the release of the cord, it is pulled and wound with a spring assembly. When the internal combustion engine is launched, the trigger rotates its shaft until it starts to work.

Today, gasoline scooters are equipped with two types of starter mechanisms:

The first option is much more common.

The trimmer starter for grass can work without breakdowns for a long time. It is impossible to clearly indicate a continuous period of time. Everything is determined by the initial quality of the device and compliance with the rules of its operation.

The main malfunctions of the trimmer for the grass of the starter

It is easy to determine the reason for the refusal of the starting device. There are several main options:

Perhaps the starter mechanism is accidentally broken. The consequences will be deplorable if the wrapped cable is wrapped around the flywheel of the internal combustion engine: then the spring will burst and the pulley will break. But such cases when a complete replacement of the starter is required are extremely rare. In most cases, it is enough to fix a new spring or replace the cord to fix the mechanism.

Springs of the starter of the chainsaw

Starter Spring Husqvarna 137/142/235E/236E/240EE

Hand.based Hyundai X460 chain starter

Starter Spring Husqvarna 137/142/235E/236E/240EE

Starter spring for Carver RSG-45-18K/RSG-52-20K (light.

Starter for the chainsaw Husgvarna 137/142

Hand starter for one.handed chainsaw 26ss and analogues

Starter in the collection of a gypsy chainsaw 65.72 QU.

Light start of the starter of the lawn mower

Chain gasoline saw Craternum GCS-1200/350h

Starter coil spring Khusqvarna Art Art. 586659.

Starter for the Forward FGS 4504/5204 chainsaw

Spring of a template starter for a chainsaw 45/52 Narrow ki.

Starter in the collection of the Gypsy chainsaw 25 (Forza.

Starter Spring for Chainsaw Carver RSG-45-18K/RSG-52-.

Starter spring 137 240 = Husqvarna Art. 5300211-80

Ergostart starter spring in the stih chainsaw building.

Starter for the Forward FGS 4504/5204 chainsaw

The starter pulley for the chainsaw Husqvarna 137, 142 from the springs.

Chain gasoline saw Hammer BPL 4116 A

A hand starter is suitable for a chainsaw type P350.

Starter spring overtaking with a pulley 128/323/325 = Husqva.

TOHATSU manual starter spring 350-05124-0

Starter spring 340e Husqvarna (5374234-01)

Spring for a starter for a chainsaw STIHL MS 170/180

Partner 350, 351, 352, 370, 352, 370.

The starter of the starter for the chainsaw is 45/52 wide.

Ergostart starter spring in the stih chainsaw building.

Starter for a chainsaw with an engine volume 38ss. (two pr.

Partner P350S chain starter (regular start)

A hand starter is suitable for chainsaws with a volume of 38cm3 light.

Starter in the collection of the Gypsy chainsaw 45.52 QU.

Starter spring for the chainsaw Husqvarna 545, 555, 560x.

Spring for a starter for a chainsaw STIHL MS 170/180

Starter for chainsaws: Husgvarna 5200 (Gypsies), Stihl M.

Starter spring for the chainsaw Husqvarna 268, 272xp

Starter assembly for Partner P350S, P360S

Starter spring for Husqvarna 365, 371, 372k (5037872-.

Starter spring (see the kit) = Husqvarna Art. 53742.

Starter assembly for Partner P350S, P360S

Starter Spring for Chainsaw Carver RSG-45-18K/RSG-52-.

Manual starter spring Polaris SM-11025D

Return Starter Spring MS-180/170/210/270/360/440

Starter for chainsaws is suitable for Stihl MS 180 Green

Ergostart starter spring in the stih chainsaw building.

Starter pulley for a chainsaw 45-52 Easy start from springs.

Starter assembly for chainsaw Huter BS-45, BS-45M, BS-52

Return springs of the manual starter Polaris Sportsman /.

Starter spring for the chainsaw Partner P350S Rezer

Starter spring for the chainsaw Partner P350S

The starter of the chainsaw starter Partner 350, 351, 352, 370.

Starter spring with a drum BS 450/500 Series (49.

Starter for a chainsaw with an engine volume 38ss. (two pr.

Starter assembly of Champion 245.254 Light start (30020003.

Starter spring Partner 340s, 350S, 360S. Chinese b.

Starter spring for the chainsaw Partner P351 Rezer

Starter spring for Husqvarna-236 Rezer

Starter for the chainsaw Patriot 3816 (with one spring)

Checking filters

Another common cause, due to which a trimmer for grass does not start, is the presence of a blockage in the filter area. To confirm the conjecture, just dismantle the indicated block and try to start the unit without it. If the engine of the trimmer for the grass has launched, most likely you will have to replace the air filter or at least perform a thorough purge of the old. In the presence of abundant contaminants on the surface of the filter element, it is necessary to use a new grid. Relying to such actions, you should not leave a suction pipe at all without a filter. After all, rush in this case can lead to the need to repair the entire piston group of the unit engine.

Before setting up the carburetor trimmer for the grass, it is necessary to do the following:

• Rinse the engine;
• replace or clean the spark plug;
• change to a new one or clean the air filter (it is recommended to lay it out in warm, soap water, squeeze it out and let it dry well).

It is also necessary to install the cord of the right diameter in the trimmer coil or install knives-this is done so that in the process of configuration the engine has at least some load. After installing a cutting tool and starting a gasoline engine, let it warm up for 10 minutes.

If at the idle speed of the motor you noticed that the cutting tool rotates, then it is necessary to reduce engine speeds. This is done using the lower idle regulator, often marked with the letter “T”. The figure below shows the placement of regulators on the trimmer Husqvarna.

But, for example, on the STIHL trimmer, this screw may have a label “LA”.

So, turn the idle control regulator to the left, until the trimmer head is completely stopped.

To configure the carburetor, 3 regulators are used (screw).

• The right regulator L tunes the level of enrichment of the combustible mixture at low speeds. It needs to be adjusted by the first. Get a maximum of turnover at idle. This is done using the regulator L, turning it to the left and right. After finding the point of maximum revolutions, return the regulator for half a turn to the left (against h. Arrows).
• The lower regulator t (LA) is used to configure idle. Turning it to the left, the engine speed will begin to decline, and when the regulator is turned to the right, the revolutions will increase.
• Left regulator h is responsible for enriching the combustible mixture at high speeds. The enrichment configuration completes the adjustment of the carburetor. Also, using this regulator, you can configure maximum speed, fuel consumption and engine power.

To exclude this trouble, adjustment will be required. With the working motor, give a full gas, then turn the “h” regulator to the right until a reduction in revolutions begins. After that, the “h” regulator must slowly scroll to the left until you hear the uneven operation of the engine. Then the regulator “h” should be rotated to the right until the moment of flat operation of the motor is heard.

After conducting the above actions, the setting of the carburetor can be considered completed. After proper adjustment, the engine must confidently gain momentum, a little four at a maximum of revolutions, and when working, an idle cutting tool should not turn. This manual is suitable for adjusting carburetors on the Huter, Patriot and others benzocos.

There are also carburetors without a screw that is responsible for enriching the combustible mixture at low speeds. That is, they have only 2 adjusting screws: a idle regulator and a quality fuel mixture regulator at high speeds. How to configure a carburetor of this type, you can find out from this video.

Analogs

On the world and market, two brands selling similar products. Sturm and Fubag can be distinguished. They are represented by the following models: the German benzotrimmer Fubag FPT 52 38712 and Sturm BT8952D, which have similar characteristics and fall into the same price range.

I purchased this model of a trimmer for grass last year to restore order on a garden plot. He used it only a few times, mostly my wife works with him. He copes with weight until she complained. Says that it is convenient to work. According to my feelings, I can say that it is very light and comfortable, if there was still a belt, then she would not be the price. For the overcrow of trees and shrub is great. In my opinion, it is not suitable for kosba in large volumes, since hands get tired. Otherwise, there were no problems with a motorcycle, everything works fine and does not fail.

I have been using this model of a trimmer for grass for 2 consecutive season. I mainly use hard.to.reach areas for the overcrow of hard.to.reach areas. Since you will not crawl to the trees and the fence close, I use a trimmer for grass. I like this tool. Starts the first time, even in cool weather. To do this, you only need to pump up a little fuel. And a fishing line for a trimmer is also very easy to change in it, there is a special position for this.

I was prompted by a constantly neatly cut lawn of a neighbor to buy a trimmer for the grass). I come to the cottage, I see his lawn and I want to put the same order at home. For this and acquired it. Now in my summer house, everything has become neatly and clean. In the management of the trimmer for the grass, I am quite happy with me. There is not a lot of fuel. Only noisy, but they, in my opinion, are all so loud. If we start mowing with a neighbor, such a symphony turns out that you can hear the whole district. I definitely recommend the acquisition.

Echo SRM-2655SI

The lawn mower starts poorly? adjust the gap of magneto rating: 5.0

Lawn mowed on a straight rod weighing 5.9 kilograms. The power of the 2-clock engine is 1.1 liters.With. Trimmer for grass works with a fishing line with a diameter of 3 mm or a knife. Speasing width is 43 centimeters, and the tank capacity is 650 ml. There is a light start system. A convenient shoulder belt is supplied to the kit. A successful anti.vibration system.

To work in any position, a braid for grass is equipped with a rotational carburetor.

Review: not the most powerful model, but extremely comfortable and productive. If you install a wide fishing line for a trimmer, there will be no trace of dryness. Users also note that in the end it is not possible to perfectly align the lawn as a lawn mower (but this is not a lawn mower, but a trimmer for grass). Buyers are attracted by a long warranty (5 years), which fully justifies itself. True, to provide such a guarantee, it is required to take place in the official service, promo like cars. The device is not prone to breakdowns.

Barbell

Which bar to choose? The rod of a trimmer for grass is part of the design that connects the engine block with the cutting element. Inside the bar is a shaft or a cable that transfers the rotation of the engine to the cutter. The rod can be made of collapsible, which allows you to conveniently store and transport a trimmer for grass. Also rods are straight and curved.

Straight rods are characteristic of professional trimmers. A durable shaft is more reliable and durable than a cable, with its help you can transmit more power, which allows you to easily cut small branches and shrubs. It’s good if the shaft shaft is forged.

Curved rods are considered more ergonomic. Their shape provides a greater maneuverability of a trimmer for grass and allows you to process inaccessible, complex areas. It is more convenient to keep such a braid, and less effort is spent on it with its help.

Patriot Pt 553 (11)

• ICE power: 3 l.With.
• Fuel tank capacity: 1.1 l
• Speasing width: 44 cm
• Cutting element of a trimmer for grass: a fishing line for a trimmer and a knife, a fishing line for trimmer 2.40 mm
• Weight: 7 kg

Great trimmer for grass grass, which is only slightly inferior to the previous model. The well.thought.out design of the device provides ease of maintenance due to easy access to the candle and air filter. Advantages of Motokos:

• Forged shaft providing the durability of the trimmer for grass;
• Ease of work by adjusting the U-shaped handle;
• Shoulder belt in the kit;
• The supply of fishing line is carried out semi.automatically;
• The vibration system helps to reduce fatigue during operation;
• Smooth starting system without jerking Easy Start.

Power

What power to choose? The power of a gasoline trimmer for grass is considered in the same units as in cars. in horsepower (l.With.). The greatest value is 4.7 liters.With such motorcycles are designed for professional use. They easily work for a long time and easily cope with any types of grass, can even cut small branches and shrubs.

If the device is planned to be used rarely and for simple work, for example, haircuts of grass on flower beds, then an expensive powerful trimmer for grass is not needed. It is enough to purchase a model with a capacity of up to 1 liter.With. In case of larger work, such as mowing herbs in a personal plot, it is worth using a medium.power motorcycle engine of 1.2. 2 liters.With.

DIY lawnies repair: analysis of malfunctions and methods for their elimination

The lawn mower is one of the main instruments of the summer resident used to quickly bring the land in order. The owners of private houses acquire this weapon for mowing grass in the personal territory. The period of active use of benzos and electric trimmers falls on the summer period. Before starting operation, the tool is brought into working condition: the rubbing parts are lubricated, the cutting headset changes, the fuel mixture is poured into the tank. If the engine does not start or stalls quickly, without gaining enough revolutions, then you have to look for the causes of problems and eliminate the identified malfunctions. To carry out the repair of the lawn mower with your own hands, you need to understand its device and the principle of operation of the main nodes. This information can be found in the operating instructions, which the manufacturer applies to garden equipment without fail. Check for such a manual when buying a chainsaw. The import tool should be accompanied by instructions written in Russian.

If the resource of the fuel filter has not yet been developed, then it makes sense to tackle it. To do this, use kerosene, acetone or blowing with air from an ordinary pump. However, not all drivers share this opinion and believe that in case of violation of the engine, it is necessary to replace the fuel filter in a timely manner, especially if in the instructions for the car it is ordered to change it through a certain mileage, thereby not creating interference with the operation of the fuel system. over, the cost of such a filter allows you to do this without any difficulties.

Rinse such a fuel filter late, it should be replaced

When it is poorly started on a hot diesel engine

To chagrin, diesel engines also from time to time may not start on a hot. In most cases, the causes of this phenomenon are malfunctions of subsequent nodes:

• Cooling water sensor. Here the situation is similar to the one that was described in the last section. The sensor may fail and, accordingly, transmit incorrect information to the ECU.
• The crankshaft position sensor. Situation similar to an injector engine.
• Air mass flow sensor. Similarly.
• Fuel pump of the highest pressure. Namely, this can happen due to a significant wear of bushings and a pumping shaft of the pump. Air enters the pump from under the omentum, which is why it becomes impossible to collect working pressure in the prelunate chamber.
• Diesel engine.
• Fuel pressure regulator.
• Ignition module.

Now we will try to summarize the information given so that it is easier for you to find the cause of the breakdown if it happens to your car.

Checking the ignition by oscilloscope

What to do if the used fuel mixture is in perfect order, but as before it does not start Trimmer for grass

petrol? The prerequisites for the refusal of the mechanism can lie in excess moisturizing the candle channel. To diagnose and eliminate the task, you need to make the next:

• Turn the candle. Wipe it painstakingly, and then dry it.
• Drain the excess combustible in the chamber through the corresponding candle hole.
• Clean an old candle if there is a dozen on its surface. The use of an ordinary ladies’ nail file or a file will allow you to cope with the task.
• When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the lumen.
• Collect a multifunctional block back.
• Try to start a trimmer for grass.

The lawn mower is not started on hot

If the lawn mower was not so long ago in work and has not yet managed to cool but did not want to start. press the gas trigger, sharply pull the starter’s cord a couple of times until the engine is started and the gas trigger is released later. If quite a lot of time has passed and the lawn mower managed to cool, then you need start

As with cool. If the above methods did not help, the lawn mower did not start, then you should contact the service center.

How to prevent sudden breakdowns during the operation of a trimmer for grass?

In order for the unit to be always in working condition, it is worth observing several ordinary rules:

• In time, conduct a constant technical inspection of the main mechanical components of the device.
• Refuel a trimmer for grass with only the latest fuel, the quality and origin of which does not cause fluctuations.
• After each use of the tool, inspect whether oxides and soot on the surface of the ignition system have formed.
• Fear huge loads on the trimmer for grass during operation.

So that the unit remains in working condition, you need to correctly prepare it for storage in winter. First, you should make the tool absolutely disassemble, and then wash and clean the constituent elements. It is also fundamentally examined by multifunctional blocks for damage, as needed to exclude deformation of parts, various distortions, gusts of materials.

Spring can interfere

My first attempt to adjust the brace of the carburetor failed, because the spring of the adjusting screw of the fuel mixture prevented this. The factory spring was too thick in a compressed state and did not allow to reduce the supply of fuel to the required level. I had to collect another spring and continue to adjust after its replacement.

In the photo above. Factory spring, below the adjusting screw with the selected spring. I write about this because I’m not sure that this is an isolated case, and someone else may face the same situation.

From personal experience

lawn mower or trimmer for grass

Trimmer for grass. This is a broader concept than a gasoline braid for grass, because it can also be electric. Gas trimmer for grass and brush. This is the same.

Some authors argue that a trimmer for grass is a weaker tool compared to more powerful bush cutters that can be used to mow bushes. Personally, I have a tool with a maximum power of 1.7 kW, and I can mow a small bush up to 10 mm thick, as indicated in the instructions. User manual is called “gasoline trimmer for grass.””.

The ratio of the fuel mixture

Somewhere I read that if the instructions for a motorcycle and oil may indicate different proportions of the preparation of the fuel mixture, you should use the proportion specified in the manual.

This took place for a long time. Excess oil came from the engine to the gas tank, and soot was constantly formed on the spark plug, because the instructions indicate the proportion for engine operation at 1:25 and the canister. 1:50. Has stopped. The spark plug continued to burn, but with less intensity (the carburetor has not yet been adjusted).

Until now, some users of gasoline instruments determine the proportion of the fuel mixture “by eye”. If the amount of oil is underestimated during the preparation of the mixture, after some time, immediately after the engine starts, a strange sound may appear, gradually disappearing during heating, and the engine stops sharply. Continuation of the work of a trimmer for grass in this mode will lead to its failure.

Cleaning candles

In the worst times of working with a trimmer with an unregulated carburetor, the engine stopped starting after using each fuel tank. And only by cleaning the candles of soot, we could continue to work.

Subtle sandpaper was used to clean the electrodes, and a thin bracket with a bent end was used to clean the space between the insulator and the case. At first, the electrodes were wiped with high mud with a rag, then they were cleaned with sandpaper. After that, the candle was lowered into diesel fuel, and the moistened soot was scheduled with a paper clip for papers from the surfaces of the insulator, the inside of the body and between them. Then the candle was loaded several times into diesel fuel, which was then shaken off with impurities. Иногда процедуру чистки скрепкой и промывкой повторяют. After that, the candle was wiped dry and were ready for further use.

It is unlikely that one fuel tank with an unexplored carburetor can be spent in less than 10 minutes. This was tested in practice, when the trimmer for the grass launched and worked at high speeds with maximum fuel supply (the adjusting screw was unscrewed much more often than usual) ,

Gas braids for grass, like all gasoline tools for the garden, are not easy to serve. You can and should repair, configure yourself. For example, self.government by a carburetor using a home.made brush. The point is five minutes.

Kustorez carburetor is a knot in the energy system. In it, as in any carburetors, there is a process of mixing air and fuel (gasoline) for subsequent supply to the engine cylinders.

Tools

Trimmer for grass gasoline Patriot RT 3355 is designed to trim and mow low grass on lawns, streets, around trees, along the roadsides, on lawns and garden areas. The unit is successfully used on even and relief, uneven areas. The manufacturer improved the model taking into account convenient transportation and easy use: the bar is made by a detachable, quickly assembled and disassembled. The comfort of operation adds a wide shoulder belt with an adjustable length. Fast launch is simplified by the primer.

For its motoblocks, Patriot has developed a number of attachments that saves the time and effort of the owner. Photos of some devices can be seen below, the most popular models are also presented below:

Ceremonial cerebral pages

• Hellets of different species are used to lay the furrows for planting;
• Potato.captacco is used to facilitate potato collection. The device lifts the tubers and separates them from the ground;
• Mowers are rotary or segmented. Used for mowing grass and grain crops. After mowing, put the grass in the ranks, which are subsequently easily assembled;
• Cart or trailer are designed to transport goods;
• The adapter is used to facilitate the process of working on a walk.behind tractor;
• The snowmobile prefix is ​​not installed on all motoblocks, but thanks to it, the passability of the unit increases and the work is facilitated;
• A snowmaker or a snow discriminator allows you to effectively clean the area from snow;
• The coupling is used to connect additional equipment;
• Water pump is used to supply water to the site;
• Light-off shovel is designed to clean snow, land, as well as bulk materials;
• The plow eases the virgin soil.

The device of the motor block gearbox

Reducer. one of the important components of the walk.behind tractor. It is completely on all models, without it the equipment will not work. Reducer function. uninterrupted transmission of the rotating moment from the motor to the wheels through the cuneiform transmission. Apart from that, it provides a change in the speed and direction of the movement of the agricultural unit. Simply put, ensures the movement and management of technology.

The gearbox consists of a system of shafts and stars connected by a chain. The shafts take rotation and transmit using a chain. The input shaft is equipped with a lever and a fork that switch the mechanism. From the dirt and dust, the details protect the plastic case with a bolt mount.

Motobobes are inconspicuous assistants on the farm

All parts are made of metal and need lubrication. With a shortage of lubrication, the load on contacting details grows sharply, which can lead to their renewal destruction. Timely oil substitution in the gearbox will ensure their serviceability and uninterrupted operation of the mechanism as a whole.