Cleaning Air filter of a trimmer for Husqvarna grass. Barbell

Cleaning the air filter for a trimmer for the grass Husqvarna 128r

Useful material from which you will learn how to get a capricious gasoline trimmer for grass that does not want to work!

The summer time has come, and in the personal plots habitually hidden the lawn mower. Great tool, powerful and mobile. Using a gasoline trimmer for grass and grass, you can mow, and get rid of a dried.up weed. However, there are cases that the lawn mower does not start, works with interruptions or without developing full power. Of course, no one is at work! And as they say, you twitch the laborer’s handle more than the mowing.

Difficulties with the launch do not only have the types of motorcycle, but also in new. How to be in this situation? There is only one way out. to listen to the advice of experts and take advantage of their practical experience!

If you put a cable instead of a fishing line, without the possibility of its release, reliably fixing the two ends of the cable and cutting them with welding (a drop of melted metal holds the cable from blooming). Grass such a tool “falls” at a time. The shoot is cut off about a finger with a thickness. Stones are not as afraid as disk. There is true, the problem: when wear, pieces of cable threads break off, and these twisted wires remain in the place of mowing. If you step on them, you can get hurt.

But pieces of the cable remaining on the field are half a bastard. The fishing line for the trimmer, breaking off, weakens the dynamic blows to the transmission and the engine, the cable does not give such an opportunity. Result of quick wear of motorcycles.

Also, the ignition coil can be broken in electrical equipment. In this case, the lawn mower will not start or start and works with interruptions, and then stalls, or “hot” does not start at all.

You can check the serviceability of the coil in the same way as when checking the spark: we unscrew the candle, lean it against the trimmer body for the grass. If there is no spark with a jerk of the starter, or it appears through time. you need to change the coil.

Review of models

Gasoline braids for grass are widely used for professional laws care, as well as in agriculture. These samples of modern technology have proven their effectiveness when leaning weeds and hay harvesting

In such conditions, special attention is paid to the correct choice of the representative of the model range, taking into account the design characteristics and technical characteristics

At the moment, potential customers are offered the following models of the STIHL motorcycle:

To describe the main features of representatives of these categories, it is worth considering some samples of technology. So, the light lawn mower FS-38 is designed to perform simple landscape work, as a rule, in the conditions of personal plots. The weight of this tool is a little more than 4 kg. In this case, the operating volume of the engine and its power are 27.2 cm3 and 0.65 kW, respectively.

The main advantages of representatives of this category include the following operational indicators:

• insignificant weight;
• maximum ease of use;
• minimum fuel consumption;
• power plant power;
• reliability and long service life;
• minimum noise and vibration;
• modern design.

One of the popular models related to the segment of powerful trimmers is Stihl FS-13. The “heart” of this six.kilogram braid for the grass was an engine with a volume of 36.3 cubic centimeters and a power of 1.4 kW. The model is equipped with a tank with a volume of up to 0.5 liters. Powerful lawn mowers, as a rule, are classified as professional tools with the following advantages:

• increased power;
• maximum reliability and durability;
• the possibility of processing almost any surfaces, including thick shrubs;
• convenience and ease of operation;
• the presence of a “bicycle” holder handle.

Necessary materials and tools

First you need to remove a hollow filter with nets from a chainsaw, rinse with a soft brush with household soap under a stream of hot water and blow out, for example, an ordinary hairdryer.

In this case, the plastic case must be disassembled into two parts, carefully so as not to damage, opening the latches with a screwdriver. This operation is necessary for cleaning from wood pollen of internal cavities. In addition, it is necessary to remove the elastic band, if it is of course, from the pipe and also clean it from dirt.

We collect the case back, not forgetting to put the rubber seal in place. Preparations for improvement have completed this. Now it is necessary to make a visit to the kitchen accessories of the nearest household store to buy fiber napkins/scrapers and two.layer sponges, which are used in domestic conditions for washing dishes or final refinement of various polished items

The main selection criterion is that there should not be abrasive particles on the sponge or napkins made of polymer fibers.

What to make an air filter for a chainsaw

In addition to the listed devices on chain saws, there is a system of cleaning the air supplied to the carburetor, a tire with a saw chain, a starter, a circuit tension mechanism, ignition, a silencer,

engine

The chain saw engine has a maximum speed of about 13,500 rpm. This imposes strict requirements for oil added to the fuel mixture.

clutch

At low speeds, elements with friction pads (1), which have a degree of freedom in a radial direction, are attracted to the shaft center with springs (2) and do not transmit rotation to the drum (3) connected to the chain drive asterisk. Когда скорость бензопилы достигает значений, при которых центробежная сила превышает силу пружин, сегменты трения прижимаются к внутренней поверхности барабана и начинают вращаться. As a result, the leading star begins to rotate, which sets in motion a saw chain.

As you can see in the photo, the asterisk is behind the clutch.

In other chain saws, an asterisk can be located outside the coupling.

The main advantage of this type of coupling is that when the circuit is jammed, the clutch with the chain of the chainsaw, does not drown out the engine and does not cause the destruction of the mechanisms that transmit movement from the engine to the chain.

Ignition system

The electronic ignition of the chainsaw includes the flywheel (1) with built.in magnets, the ignition module (2) with the electronic circuit, the spark plug (3) and the high.voltage wire (4). A rotating flywheel with magnets induces the EMF in the module, which is converted using an electronic circuit into electrical signals supplied to the candle. As a result, the spark lights between the contacts of the latter, which ignites the airflower mixture.

carburetor

Below is a diagram of another carburetor chainsaw.

Carburetors have a throttle that allows us to degrease or enrich the mixture depending on working conditions. For accurate setting, there are several screws that help adjust the low and high engine speed, as well as idle. Air is installed in the upper part of the carburetor

The filter that cleanses the air entering it.

Fuel system

Thus, when the fuel mixture is consumed, the fuel tank is filled with air, and there is no negative pressure in it, which prevents the fuel from entering the carburetor and at the same time prevents fuel leakage from the air hole, the cover that closes the filling of the hole is made. And by the way, if the saapun is clogged with dirt, then the chainsaw nods.

From the fuel tank, fuel is freely hanging in the tank hose. Because of this, regardless of the position of the chainsaw, the hose is always immersed in the fuel. The fuel filter is connected at the entrance end of the hose. Fuel pumps the pump inside the carburetor.

To facilitate the launch, part of the chainsaw is equipped with a hand pump for pumping. Primer. When the chainsaw is launched with a primer, the carburetor is filled with fuel in advance (excessive fuel returns to the tank). Thanks to this, the engine starts faster, because the stage of filling the carburetor is already completed by fuel, which is performed without a primer by a carburetor pump due to the starter.

Air purification system

Preliminary filters can have different design and consist of several elements, in particular, of the filters of the grid (2) and snow (1) (see. Photo below).

The latter prevents snow entering the air purification system and is used only in winter, at elevated temperatures it is removed.

In some models of the chainsaws at the preliminary cleaning stage, air purification is used using centrifugal forces. The air flow is twisted by the impeller of the flywheel, as a result of which impurities are thrown out of the suction pipe going into a thin filter.

Thin filters are made of diffusion foam, nylon mesh and other materials.

When the chainsaw works, the air in the zone of its action is highly contaminated with sawdust and wood dust. Excessive filter pollution reduces the amount of air entering the carburetor, which leads to enrichment of the mixture and reducing the power of the chainsaw. Therefore, regular cleaning of the filter is needed. It must be performed not only when dismantling the chainsaws with the aim of repairing it, but much more often after long and dirty work. Cleaning is carried out using a method that depends on the type of filter material. most often by purging and washing.

Filters on Benzopile.

.Filters are swollen. where are they, what they are, how and when they change.Air Phil.

A gas station, the final air filter filter

My clarification (improvement of air purifier in Chinese chainsaw

Starter

The starter mechanism consists of a drum (1) with a cable (2) and a handle (3) and a frame (4) with a return spring. Когда рукоятка резко поднимается вверх, храповик барабана зацепляется с зубьями на валу двигателя и проворачивает коленчатый вал. When the handle is released, the return spring returns it to its original position.

To tighten the crankshaft with the speed at which the engine starts, a certain force is required. The launch of a chainsaw with one jerk often fails, you have to jerk several times. Various methods are used to facilitate the launch. To enrich the fuel mixture with a carburetor valve or reduce the pressure in the cylinder using a decompression valve (to facilitate turning). The valve automatically closes when the pressure in the cylinder increases when the mixture is ignited. Sometimes an additional spring is used in the starter mechanism, which is first compressed when the cable is pulled out, and then it is sharply unclenched, rotating the engine.

The main and most complex links of the chains are cutting lines that are divided into right and left. The upper edge of the tooth. The widest of all elements. It provides a wide cut, eliminating the jamming of other links.

The shape of the cutting teeth can differ significantly between the chains of different manufacturers. There are two main forms. Chipper (A) and Doloto (b). However, there are various intermediate contours of the incisors.

Types and principle of the filters for a trimmer for grass

In modern motorcycles, two types of filters are used. fuel and air.

Even the highest quality fuel has various additives that quickly accumulate and disable the technique.

The task of the fuel filter in gasoline trimmers is to protect the device engine from various impurities contained in gasoline and oil.

Outwardly it is very small in size. Make it from felt material. A compactly folded felt manufacturer placed in a metal tip and has on a fuel tank on a fence tube.

Another placement option is in the highway between the carburetor and the tank. Many owners of trimmers note even excessively thorough cleaning, so the material is quickly clogged so much that it requires a complete replacement.

Original consumables can be purchased in specialized stores. Average apiece.

Its main purpose is to keep the dirt and dust entering a trimmer for grass grass during operation.

With mowing, not only dust rises into the air, but also a small SOR, crushed grass, which can quickly clog the technique. A good filter will prevent engine breakdown, even if the air is very contaminated.

The place of its location can vary depending on the model of the trimmer for the grass, but is usually located on the side of the device under the protective casing.

The casing is fixed either on a bolt or latches, which are very easy to open to remove the contents. The filter itself can be made in the form of a ring or plate of foam, felt, fleece.

If you mow on average 1-2 times a week, then it will be enough to replace at least once a year. With more intense use, check and replacement should be carried out more often.

Why is the gasoline trimmer not starting for the grass

Comparison EarPods: Original or Chinese copy? Buyer’s instructions

The reasons why the gasoline trimmer for the grass stopped starting is different, therefore, a phased diagnosis of the apparatus is required.

Malfunctions of electric trimmers

Since the device of an electric coser is much easier than a motirmer, then there are few reasons for its failure.

It should be noted that the elimination of some of them is best entrusted to the specialist.

Basically, the trimmer for the grass ceases to work normally in the following cases:

• Electric cable malfunction;
• The control button is faulty;
• burned engine winding;
• Contact joints break on the engine.

Damage of gasoline trimmers

Typical breakdowns of a gasoline trimmer for grass, which are most often faced with the owners of this unit, are as follows:

• engine breakdown;
• problems with the carburetor;
• problems with the supply of fuel;
• muffler malfunction;
• gearal breakdown;
• The starter broke;
• Air filter problems;
• Broken a buckshot on a gas tank.

How to wash an air filter on a benzotrimer, an IZHMASH Izhmash Industrial Line GT 4350

The place of its location may vary, starting from the model of the trimmer for grass, but is usually located on the side of the device under the protective casing.

The casing is fixed differently on the bolt, as it is also called latches, which are not at all difficult to open to pull out the contents. You will like the filter itself, the type of ring is made on a different plate of foam, felt, fleece.

If you mow approximately several times within a week, then the shift will be enough at least once a year. With more saturated use, the check and the change are made to be carried out more often.

At some point, there will certainly be a need to wash the air filter for the Husqvarna grass, as it is also called another manufacturer. There are no difficulties, and remove the pollution from it of course without the help of others a couple of hours before the mowing.

• Unscrew the bolt on the protective casing or squeeze the latches.
• We take out the filter and inspect. In order to remove the accumulated oil and other contaminants remains our client, gasoline will need.
• We water the gasoline from the canister to the dirty filter and wash off the oil remains our client. Squeeze and leave to dry at least 4.5 hours.
• We wipe the installation site with a cloth moistened in gasoline.
• We install what remains to make our client in the area and close the casing.

Lapal water is used instead of gasoline, but it removes the mud all the same not so fine.

In the role of a candidate, flushing can be recommended by blowing or just shaking the litter. These cleaning options are suitable provided that there are no oil pollution.

If the trimmer for the grass began to stall at high speeds, most likely, the fuel filter is so contaminated that it asks for an urgent shift.

How to clean an air filter | How to Clean The Air Filter

Make it completely affordable for everyone. Of course adhere to the subsequent method.

The 1st that you need to do this to extract a festive tube (watch the video), because the filter itself is the snitches of the fuel tank. For this purpose, we pull your hands for the pipeline only on ourselves. In the process of removing the seal, the fence tube should jump off and stay in the tank. Pinzet will help to pull it out of there. There is also an option to drain gasoline from the tank and remove the fence pipe through the hole.

We take a new filter, put it on him a fence tube and a spring ring.

We install the sealing ring back on the pipeline, fasten the fence tube with a new filter to it and season in the tank, coupled with the tube.

Install the sealing ring to the district. We turn a little around our own axis, so that the connection is fixed.

How to clean an air filter motorcycles ?

How to wash or clean an air filter on a benzotrimer, benzos, experimental: Izhmash Industrial Line GT 4350.

Gasoline used in motorcycles. AI 92. The brand of gasoline is accurately prescribed in the operating instructions. Do not try to “force” the engine, filling the 95th gasoline into it. This can lead to overheating, unstable work of a trimmer for grass and breakdown.

It is not recommended to leave fuel in a trimmer tank for grass with a long break in operation. It is better to finish the working day by completely developing the entire mixture. If this is not done, then because gasoline from the engine will evaporate during the night, and the thin oil filter will remain, carburetor jacks may clog. This will cause difficulties the next engine start.

It is also necessary to observe safety precautions when storing fuel. Many pour gasoline into a plastic bottle of water. Is it worth doing so?

In no case should you store gasoline in plastic containers from under water. When mixing the fuel mixture, a static charge accumulates, you can “catch” the spark.

Therefore, at gas stations it is not allowed to refuel gasoline into plastic canists, only in metal. Before pouring gasoline in a metal canister, it is better to put it on the ground, so statics are removed from the case.

But there are situations when simple manipulations with a motorcycle do not help. The engine still does not start. In this case, we are in progress, we check the power and ignition system, guided by the rule “the motor does not work if there is nothing to burn or set it on fire”.

Replacing the crankshaft oil sector, throws oil on the case repair of the gas.suction of the ignition coil

Why change the crankshaft oil seal, how to do it, we look at the order of work on my channel. Why.

The performance of a wheelbanger is several times higher than a manual lawn mower. And managing it is no more difficult than rolling a baby stroller. Just go and direct it. Especially if the lawn mower is self.propelled. Even children will manage with her.

Wheel lawn mowers have a 4-stroke and their maintenance is difficult like a car.

Wheel lawn mowers usually have four.stroke engines. The fundamental difference between four.stroke engines and two.stroke. the presence of a crankcase in which the oil lubrication is located. Therefore, for the normal operation of the 4-stroke engine, you do not need to prepare a fuel mixture of oil and gasoline, it is enough to fill only gasoline into a gas tank. This circumstance is presented by some dishonest sellers as a dignity. “they say, do not mess with the preparation of the fuel mixture”. At the same time, they “sweetly” miss such a detail as the need for at least annual oil replacement in a wheelhouse of a wheeled lawn. The procedure is not complicated, it is much simpler than that of the change of oil in the car, but more complicated than the preparation of the fuel mixture. Generally speaking, the oil in the crankcase of the wheeled lawn mower must be changed about every 50 hours of its operating. The lawn mower is not an oil filter and therefore the oil is not cleaned there. This determines the rapid oil replacement mode. On the other hand. 50 hours of operation of the lawn mower in the season. this is a very big developing.

The process of replacing the oil in a wheeled lawn mower is simple. Before replacing the oil, it is advisable to give the lawnapers to work for 10-15 minutes, so that the oil warms up and becomes more liquid.

In the design of any lawn mower there is a special screw covering the drain hole from the motor crankcase. Usually it is located under the filled and measured neck of the crankcase. (in the photo. indicated by an arrow).

The lawn mower is installed with a slope towards the drain hole, placing wooden churbak or brick under the casing from the opposite side. After that, unscrew the screw. cork. So that the oil does not spill on the casing of the lawn mower, a gutter is cut out of a plastic bottle, according to which the oil will flow into a substituted container. It is advisable to produce gasoline before replacing the oil from the gas tank.

After that, the screw. the cork is unscrewed and the cliff is dragged, tilting the lawn mower. When the oil is draining, the screw is screwed into place. Fresh oil is poured through a measured neck. Typically, it is recommended to use oil with a viscosity of 10W40, mineral or semi.synthetic.

Inexperienced owner of garden motorcycle equipment, of course, is inclined to almost idolize a new purchased technique, up to fetishism. He wants to fill it into it and better gasoline and the oil is more expensive. This is a typical mistake leading to a very quick way out of the technique!

The fact is that this garden technique is made by the “stream”, t.e. The materials in it used the most common, not special. The gaps to the engines are “conveyor”, no one was rubbing anything there. Therefore, you can not pour more liquid oil than recommended by the manufacturer. It simply will not stay in the clearances between the details.

You can not pour gasoline of a higher brand than recommended. Since gasoline with a higher octane number burns longer. And this is fraught with the fifth of the valve, piston or rings.

It is impossible to fill the oil more than the supposedly in the fuel mixture for two.stroke engines (so that it would be better lubricated). The saying “Porridge can not spoil” porridge “here at all. Everything should be in moderation here. In general, carefully read the instructions and follow it, not the advice in Internet forums.

In general, maintenance of both 2 and 4-stroke engines is simple and does not require any special skills or efforts. For two.stroke engines, it all comes down to the preparation of the fuel mixture and cleaning the air filters and ventilation holes. And for four.stroke, service is reduced to annual oil replacement and cleaning water filters. Other annual preparation of the lawn mower for the season are described in another article.

Remont-Karbyuratora-Trimmera-Svoimi-Rukami-I recognize my car!

Under such conditions, it is possible to say about violations in the adjustment of the carburetor. Since quite often saved money when buying a trimmer for grass will be able to turn into the need for frequent repairs or its full replacement with a new unit. It took 2 days to understand the scheme, but the repair itself took only 15 minutes.

Exchange of experience, entertaining and necessary about everything that has their own wheels for those who decided to organize their own business.

The necessary recommendations, needlework and descriptions of self.proofs with a photo of the house is home home, maintaining and life of the household. from choosing and cooking household appliances, to leaving and raising children for pets, a home.made snowman. Trimmers for grass. Lawn mowers.

Bishops and black cutters. Boil repairs with your own hands.

With all the thirst, the chainsaws cannot be attributed to difficult if there is no confidence and experience in their own abilities, the repair of the carburetor computers, the Internet about everything regarding computers, the Internet and office equipment active vacation of the article on travel and tourism, fishing and hunting, amateur sports, about Equipment and equipment for outdoor activities, repairing a carburetor with your own hands requires certain maximum concentration and knowledge.

The most popular malfunctions of a carburetor with a mesh filter of a malfunction carburetor, much more often, two. it either clogs or breaks. In order to determine which of the malfunctions of your carburetor befell, it is necessary to unscrew the fuel filter cover and reach the mesh filter.

Removing the carburetor on the VAZ 2109-2108 The procedure is not complicated enough, and it should immediately bring the list of tools that are useful for the execution of this repair of the carburetor starting device in most cases lies in the pollution: the starting device is washed with acetone or simple gasoline. If possible, it is possible to blow out the starting device with compressed air.

In case of malfunction of the intake pipeline, the carburetor can appear traces of soot near the place with a loose connection, or a narrow fuel film. Understand the places in which fuel leaks are going on, perhaps dry, wipe all the places that arouse suspicion.

The tightening of the mounts is to be sent evenly and carefully so that there is no distortion of the carburetor flange. In some cases, tightness disturbances still remain besides at the end of the tightening of the mounting nuts.

In this case, you must clean the place of suction, and replace the gasket in it. If the circumstance of the carburetor malfunction is a breakdown of an accelerating pump, then you will need to come to terms with its replacement. Details of the acceleration pump are not subject to repair.

If the pump is working, it can be washed with gasoline or blow. It is also worth checking how the details and levers of the diaphragm of the pump freely move

Pay special attention to the ball in the spray

Replacing or flushing the filter of thin cleaning?

If the resource of the fuel filter has not yet been developed, then it makes sense to tackle it. To do this, use kerosene, acetone or blowing with air from an ordinary pump. However, not all drivers share this opinion and believe that in case of violation of the engine, it is necessary to replace the fuel filter in a timely manner, especially if in the instructions for the car it is ordered to change it through a certain mileage, thereby not creating interference with the operation of the fuel system. over, the cost of such a filter allows you to do this without any difficulties.

Rinse such a fuel filter late, it should be replaced

Replacing the crankshaft oil sector, throws oil on the case repair of the gas.suction of the ignition coil

Why change the crankshaft oil seal, how to do it, we look at the order of work on my channel. Why.

The performance of a wheelbanger is several times higher than a manual lawn mower. And managing it is no more difficult than rolling a baby stroller. Just go and direct it. Especially if the lawn mower is self.propelled. Even children will manage with her.

Wheel lawn mowers have a 4-stroke and their maintenance is difficult like a car.

Wheel lawn mowers usually have four.stroke engines. The fundamental difference between four.stroke engines and two.stroke. the presence of a crankcase in which the oil lubrication is located. Therefore, for the normal operation of the 4-stroke engine, you do not need to prepare a fuel mixture of oil and gasoline, it is enough to fill only gasoline into a gas tank. This circumstance is presented by some dishonest sellers as a dignity. “they say, do not mess with the preparation of the fuel mixture”. At the same time, they “sweetly” miss such a detail as the need for at least annual oil replacement in a wheelhouse of a wheeled lawn. The procedure is not complicated, it is much simpler than that of the change of oil in the car, but more complicated than the preparation of the fuel mixture. Generally speaking, the oil in the crankcase of the wheeled lawn mower must be changed about every 50 hours of its operating. The lawn mower is not an oil filter and therefore the oil is not cleaned there. This determines the rapid oil replacement mode. On the other hand. 50 hours of operation of the lawn mower in the season. this is a very big developing.

The process of replacing the oil in a wheeled lawn mowing is simple. Before replacing the oil, it is advisable to give the lawnapers to work for 10-15 minutes, so that the oil warms up and becomes more liquid.

In the design of any lawn mower there is a special screw covering the drain hole from the motor crankcase. Usually it is located under the filled and measured neck of the crankcase. (in the photo. indicated by an arrow).

The lawn mower is installed with a slope towards the drain hole, placing wooden churbak or brick under the casing from the opposite side. After that, unscrew the screw. cork. So that the oil does not spill on the casing of the lawn mower, a gutter is cut out of a plastic bottle, according to which the oil will flow into a substituted container. It is advisable to produce gasoline before replacing the oil from the gas tank.

After that, the screw. the cork is unscrewed and the cliff is dragged, tilting the lawn mower. When the oil is draining, the screw is screwed into place. Fresh oil is poured through a measured neck. Typically, it is recommended to use oil with a viscosity of 10W40, mineral or semi.synthetic.

Inexperienced owner of garden motorcycle equipment, of course, is inclined to almost idolize a new purchased technique, up to fetishism. He wants to fill it into it and better gasoline and the oil is more expensive. This is a typical mistake leading to a very quick way out of the technique!

The fact is that this garden technique is made by the “stream”, t.e. The materials in it used the most common, not special. The gaps to the engines are “conveyor”, no one was rubbing anything there. Therefore, you can not pour more liquid oil than recommended by the manufacturer. It simply will not stay in the clearances between the details.

You can not pour gasoline of a higher brand than recommended. Since gasoline with a higher octane number burns longer. And this is fraught with the fifth of the valve, piston or rings.

It is impossible to fill the oil more than the supposedly in the fuel mixture for two.stroke engines (so that it would be better lubricated). The saying “Porridge can not spoil” porridge “here at all. Everything should be in moderation here. In general, carefully read the instructions and follow it, not the advice in Internet forums.

In general, maintenance of both 2 and 4-stroke engines is simple and does not require any special skills or efforts. For two.stroke engines, it all comes down to the preparation of the fuel mixture and cleaning the air filters and ventilation holes. And for four.stroke, service is reduced to annual oil replacement and cleaning water filters. Other annual preparation of the lawn mower for the season are described in another article.

Repair of a trimmer for Husqvarna grass 128 r grass

Hello everyone friends!Many of you in the main work have all kinds of part.time jobs, and I am no exception, in my free time I fix the gas technician.

Today, a rather expensive and eminent animal was brought to the repair, but it is the Husqvarna 128 R Reliable workhorse, with proper care and timely service, one can say eternal!But as they say, you can break everything even glass (censorship) and so we have a mower starting up but does not hold back and stalls when stalling!First of all, we look at the candle, the candle is rushed, clean, check the compression- and it is normal, we check the cylinder cavity for grabbing and outbuildings by external inspection.Also more and less normal.

A small retreat with such symptoms. As a rule, in 90% of cases, all workshops say piston to replacement, and this is, by the way, about 7000 only a piston itself. excluding work, of course you can put Chinese piston.But this will be not that, I think that the Chinese will not make forged pistons and chrome rings, but this is so, we will return to our mower, here everything is trite, we are armed with not a cunning set of tools-traces 25 and 30 and in battle, remove the protective casing of the muffler, see that the restricted restricter is in oil deposits, unscrew it and remove the flamberry grid, it is naturally clogged.We start a motor for checking. it became better, but still stalls when loading, dig on. remove the muffler, and what we see.The exhaust window is completely clogged by the soil, the owner of this animal as it turned out later turned out to be a little stingy and pouring oil not intended for such motors. the old school M8V is all our everything!

After a long and tedious cleaning of the exhaust window, burning the silencer, and cleaning the flame.beam grid, collect everything in the reverse order, start and rejoice at saved tools, I think this essay will be useful, I attach photographs))

#Husqvarna oil service oil filter.

I use the Husqvarna HP branded two.stroke oil for this braid.

First, I tried to connect gasoline with butter with such a makar: in a glass jar (volume of jars 2-2.5 l) with an iron-coating cover (spark protection during short-term storage of consistency) added gasoline with 250 ml of plastic polypropylene measuring glass with a scale and a nose (this is a snow.white translucent soft plastic, bought in a hogm, local production) gasoline, after which he dialed the oil with a syringe and added it, later added gasoline again. But with a syringe. hard, not comfortable and for a long time.Therefore, at the moment, I mix gasoline with butter the least like this: gasoline with the same measured glass of oil (I have a scale of 10 ml) gasoline. I later pour it into the tank through the funnel.

For almost 3 years (2013, 2014, 2015, at the moment), the duraluminated fox holders (5013304) on a trimmer head erupted almost one hundred percent (1 mm remained in some places and it would be beginning to cut the head plastic), but I took them off With the help of pliers and simply turned to insert into the same place, but the other side. Consider saved some pretty penny on buying a couple of new 5013304.

Also on days at first (in the annotation it is written that it was necessary to do this even earlier): 1.) Washed the filter with household soap, the filter became snow.white, and was beige with stains. The filter is located next to the tank, where the dark gray panel is near the motor. Undetting a dark gray circle on its surface with your fingers.2.four.) Cleaned the brass grate (protection against sparks). Located on the back of the filter, you need a special batter for a manual changing screwdriver (T20 screw. I applied the photo) to unscrew the outer panel. Snutri needed a screwdriver for a minus bars with gasoline with a brush for teeth. Was with a black raid (a spot of 10 mm), almost cleaned to a brass color, but there wasn’t much time left.

Husqvarna chainsaw. Cleaning air filter

After 1-1.5 years after the purchase, I had to replace an orange plastic handle holder (545058501), t.to. The pen began to stagger (because of which it was absolutely not comfortable to mow). But, this is my jamb, I incorrectly realized the annotation when collecting, not in the right place, fixed the handle with this holder. It was very close to the engine and the center of mass was such that the holder could not stand it and tore off the thread for the 2 screws of this holder.

The braid needs to be neatly blown, and not sharply pull the cord abruptly, they say the starter in another way.

At the moment, a fishing line to zero, previously took a bit higher (frozen, but more hacking).

When the mowing is necessary carefully near trees and bushes, t.to. Having struck a tree on a tree you kill him.In order not to kill the trees, put on PET bucks for them, cutting out of the bottles from beer (the brown is also called green, it is quite transparent that it is possible to fry a tree in the sun) and snow-white from milk and kefir. Cut the neck with universal scissors, later along the seam of the bottle down to the bottom, and cut off the bottom. C-shaped protection is released (she turns into an o-film itself) for a tree on another bush.A braid for a civilized person and accurate