Cultivator for a trimmer Eletric for the grass with your own hands. In size and weight

What can be done from a trimmer for grass

What can be done from a trimmer for grass yourself to facilitate everyday work or for entertainment? This question arises if there is an old unnecessary device, or a equipment is required for operation, which, with factory manufacture, costs much more than a gasoline or electric braid for grass. In practice, many options have been implemented by the craftsmen. The main of them are a motorcycle bike, a snowball player, an ice ax, devices for the cultivation of a land plot and the mowing of lawns, saw, snowmobile equipment. To bring the idea to life, in each case you will need to apply a certain set of tools and additional materials.

If there is a cottage or just a land plot, then the cultivator will help facilitate soil processing. Traditionally, a chopper is used for these purposes, but working with it takes a lot of time and effort. The use of the cultivator will reduce labor costs, and the whole process will take a smaller time period. Factory.made equipment is expensive, therefore, with limited funds, the question arises about the independent assembly of the cultivator. For this, both gasoline trimmers for grass and electric cos are suitable for this.

To create a simple sample of technology, you should stock up on such tools and materials:

  • corner grinder with a set of disks (suitable diameter. 125 mm) for metal;
  • drill with drills of various diameters;
  • welding apparatus;
  • electrodes;
  • an electrician or a hacksaw for metal;
  • An emery machine with two abrasive circles of different granularity;
  • functioning gasoline trimmer;
  • forks;
  • pipe made of steel suitable in diameter for the shaft of motorcycles;
  • manual tools: keys, hammer, pliers, core, roulette and marker;
  • a sheet of metal with a thickness of 3 to 5 mm and a minimum of 1010 cm.

The manufacturing process begins with the working part. For this purpose, the curved rods of garden foriles will serve. Their recommended length is from 10 to 15 cm. this is enough to carry out loosening the soil.

The working nozzle is made in the following sequence:

  • The teeth of the forks are flattened to a width of 1 cm;
  • on the sandpaper, using a circle with a small abrasive, cutting cutters;
  • Using an electrician, a circle with a diameter of 10 cm is cut out of the metal;
  • process it on the emery machine until it reaches an almost perfect form;
  • At equal intervals, prepared mills are welded to the metal circle (recommended quantity. 3).

With more than 3 pieces, the number of mills, the load on the equipment increases greatly.

The recommended power of the gasoline engine should be two horsepower (about 1.5 kW) or more.

At the next stage, it is necessary to attach the cutter for weeding for a trimmer for grass. The process is greatly simplified in the presence of a reverse thread located at the end of the shaft of the motorcycles, on which the manufactured working part is simply wound. To do this, a pipe with a nut is pre.welded to the cutter.

In the presence of locksmith experience and welder skills, redoing a trimmer for grass in a cultivator is quite simple. Financial costs at the same time insignificant. If the work is used in an electric hood, then you will need to think about the extension cord so that it takes out throughout the processed area.

DIY lawn mower

The lawn mower facilitates the process of leaving decorative herbaceous plantations, and also accelerates the work in the presence of large areas that need to be processed. On the market of such equipment, many ready.made, convenient models are presented, but they are expensive, so not everyone is available. They also quickly fail in the conditions of large weeds and stones on the site. Humes are much cheaper than factory analogues, moreover, they are more practical in work.

The components of the structure of the lawn mower are:

  • engine (gasoline or electric), which is the basis of the created mechanism;
  • a frame designed to fix on it all parts of the device;
  • casing for protection;
  • knives;
  • handles and wheels;
  • control system of the controlled unit.

The recommended power of the engine used in operation is from 0.5 kW (slightly less than 1 horsepower), and the ideal is 1 kW or more.

People’s craftsmen invented many different ways to remake a trimmer for grass in a lawn mower. The simplest option is presented at

The frame version of a home.made device is very common in practice. Tools and materials for the independent implementation of the project will be required the same as in the previous case. Plus will still need:

The manufacturing process is as follows:

  • A rectangular frame 50×60 cm is welded from the corner;
  • Wheels of the desired size are installed in the corners, which can be taken even from old toys;
  • A plywood carved in its size is fixed on top of the frame or metal is welded;
  • In the center of the trolley, a hole is made for a trimmer bar for grass and fastening for it;
  • make a knife or choose a suitable finished version;
  • Then fix the motorcycle on the cart;
  • install a knife;
  • Mounted for protection against a casing from behind on a cart flying out in different directions;
  • start testing the device.

Important! The diameter of the wheels is selected so that the knives are not reached to the soil of 5 centimeters.

There are many methods of manufacturing knives, and their shape (design) is also radically varied. At the same time, various materials and old tools are used (for example, old wood saw). The main principle is that the knives are well sharpened and balanced. this is necessary to prevent the vibrations of technology during operation.

It is often found that they are not used by an old motorcycle, but only an engine from a trimmer for grass and a control unit. In this case, you will need to make handles for the cart and fix all the details of the structure on the frame.

When assembling a lawn mower and while working with it, you should adhere to safety precautions in order to avoid injuries. To collect mowing grass, you can also attach a bag to the unit.

Device

The greatest demand among farmers and summer residents is easy manual cultivators. As a rule, they weigh about 20 kilograms, differ in small sizes and high performance. The cultivator is able to loosen the ground, remove weeds, thin out plants. It is even used to make fertilizers. With this unique device, not only landing is simplified, but also the process of caring for plants.

Of course, the unoic tractor in power is more good, but for such small tasks the cultivator is better, since it has greater maneuverability and less weight. In addition, it is great for sites with complex relief or in hard.to.reach places.

The work of cultivators largely depends on what mills come to it in the kit, because it is they who perform loosening and a number of other operations. Among the working nozzles on manual models are often used as follows:

for breaking a strong earthen crust (special needle disk);

When it will be clear which cultivator is needed for certain tasks, you can choose what details it will consist of. Drawings of a homemade device can help this. The main part of the cultivator is an engine that can be electric or internal combustion. It is best to give preference to reliable and durable attitudes. If necessary, it is necessary to provide a cooling system, since it is not always built.in.

The gearbox is responsible for monitoring the torque of the engine. This part reduces speed, and also contributes to the operation of the power shaft. As for the frame and the portal for hinged equipment, they can be made from what is at hand. To do this, even the simplest two.wheeled car will fit. The main thing is to think in advance about the scheme in order to imagine well how and where individual elements will be placed.

Convenience and the ability to adjust are important parameters for the control lever. It should be not only convenient, but also adjustable.

As a rule, the handles are supplied with all the elements responsible for the control of the device. Therefore, it is important to imagine well in advance how the unit will look like a whole, so that it is convenient to use it.

How to do it?

A hand cultivator can be quickly and simply done with your own hands. And you should not be afraid that special skills, materials or tools will be needed. in most cases the unit can be collected from what is already at hand.

If you find detailed instructions, you will need no more than 20-24 hours to collect the device. Homemade cultivator is also convenient because it is easy to fix or improve.

The simplest model of a universal assistant is a model similar to Tornado. Such cultivators work without fuel and electricity. All work is carried out by its own efforts and tools. Such a device is made from the forks, while the teeth bend with a hammer so that they look like a boletus. Then the simplest handle from the shovel is attached, a plastic pipe is put on top of it, all this is fixed using island.

Depending on which mills are used, cultivators may differ. For example, there are needle models that are a type of rotational star device. They do a great job with loosening and extermination of weeds. Even more functions allows you to perform a hinged lancet cultivator, its milling cutter resembles “goose paws”. Such an unit can loosen, cut weeds, comb out the remains of plants, level the surface layer of the earth.

Making a cultivator yourself is very simple today. To do this, you can use many devices. For example, gardeners make helpers from corner grinding, a bicycle, an old washing machine, a drill, and even from a snowman.

From corner grinders

The burned corner grinder can be successfully converted into a cultivator. Of course, such a tool will not be able to process large areas, but it will help to cope with the summer cottage or even a greenhouse. The main advantages are its environmental friendliness, small weight and ease of operation. Such a device works from electricity.

To collect the unit, you will need a welding machine, as well as at least minimal skills to work with it. Materials for manufacturing will serve:

engine from a washing machine or drill;

chain and “stars” from a small bicycle;

Cultivator mills that are made from a car spring;

tin to protect the motor from the land entering it.

The design will be a frame of metal with two wheels. In its center there will be a engine, which must be connected to cutters. Rotation will be provided using bicycle “stars” and chains. As for the cable with the starting mechanism, it is attached on the handles.

From a trimmer for grass

An ordinary gasoline trimmer for grass for the garden, thanks to the dexterity of the hands, can easily turn into a small cultivator. The following materials will be needed for its manufacture:

It will be most convenient to process the metal using angular grinder, welding and manual tools. The working part will be a rod from the forks, only curved and flattened. Before work, they must be sharpened with a disk with small abrasiveness. Cutters must be removed from each other to an equal distance with a round element with a diameter of 10 cm. Ideally, if the cultivator is equipped with three mills.

From a chainsaw

Chainsaws are also suitable for the manufacture of a cultivator on its own. The engine “Friendship” is best suited. The creation of a device based on a chainsaw will require, in addition to the engine, a number of materials:

chain (you can bicycle or from a light motorcycle);

It is advisable to have a grinder, welding apparatus, lacture keys (set), pliers from the tools, plots. First you need to assemble a frame. This is best done using contact welding or bolts. Then you need to weld the crosses that fasten the frames. It is on them that the engine is installed from the chainsaw. The lower part of the frame is supplied with a shaft with wheels, an asterisk and a chain. As a working part, a shaft with mills is made, the fastening of which is made by square sheets of metal.

Rotary

Discs are a good basis for the cultivator. However, making a rotary device is very difficult, especially if there is no special skills for this. Of the details will be needed:

To the bushings that are fixed on the axis, it is necessary to weld the wheels. With the help of Shplint, the axis is fixed in brackets. A pipe with handles and a crossbar should pass through a large bracket. In a small bracket, you need to screw the rod that protrudes above the crossbar. Such a cultivator is reliable and practical.

Nazadka-cultivator for a trimmer for grass: nuances when working and mounting methods

Owners of suburban plots and houses often buy a gasoline trimmer for grass with a rather powerful autonomous device that can cope with all kinds of agricultural work.

And given that manufacturers often equip the tool with various useful nozzles, for example, bluffs, grinders and bush cutters, then working with such a device becomes one pleasure! In today’s material, we will not deal with the features of the work of various nozzles, but let’s talk about one specific solution-about the nozzle-cultivator for a trimmer for grass.

Mounting methods and design

Modern nozzles-cultivators can be performed in two performance:

  • Toothache, in which cutters are located sequentially on the shaft;
  • Disk, when several cutting discs act as cutting organs.

Despite different names and designs, by and large the fundamental difference is only in the form of a loose knot.

Rosted nozzles for a trimmer for grass differ in a smaller mass, and therefore are better suited for processing light soils. As for disk models, they are used to loosen more heavy soils, as they have greater stiffness.

The torque is transmitted to the nozzle-cultivator from the engine thanks to the shaft, which is combined by means of a special bar. The latter, unfortunately, often has to buy separately.

The unit under consideration cannot be called interchangeable, while the number of slots on the end part of the bar may vary from 7 to 9. Based on this, buying a cultivator nozzle, for example, from Oleo-Mac it is worth knowing that it is not suitable for working with the Husqvarna trimmer, as vainly.

The slotted method of fixing the cutter or disks to the shaft provides for a free displacement of the cutting organs, so that the soil will be loosened with a fairly wide coverage-200-250 millimeters.

This option is perfect for the purpose of cultivating the Earth on the site, since it eliminates the large amplitude of the bastard of the bar during operation.

In addition, this method allows you to reduce or completely abandon restrictions on the density of the beds.

When processing long beds, the process of working with a nozzle and a trimmer becomes even more convenient, since in this case you will have to make turns much less often.

Nuances when working with a cultivator nozzle

It is important to emphasize that any kind of nozzle significantly increases the mass of the entire tool as a whole, and weight growth is often at least 5-6 kilograms.

That is why prolonged work with a trimmer in this case becomes far from far from everyone! In a series with this, when choosing a nozzle, it is important to consider mechanical restrictions on the power of the device drive.

For example, if you have chosen a model of a trimmer for grass with a engine of less than 1,500 watts, then when processing the soil, you will have to limit yourself only to hilling of potatoes and beds, since it will be possible to work only with regularly loosened land!

Since the drive bar has a considerable length, and the drive itself in trimmers operating on gasoline is usually placed behind the worker, then in the process of cultivation of the work they are accompanied by noticeable vibrations, the value of which can vary depending on the load on the cutters and wheels, as well as the length the bar itself.

Through the shoulder belt, the vibration data are transmitted directly to the person’s hands, and therefore it is difficult to hold a considerable node and at the same time control the button of soil cultivation is difficult.

Given this, it is important to emphasize that prolonged soil processing with a cultivator nozzle does not always remain safe for human health.

But there are advantages: so increased mobility of a hinged gasoline trimmer for grass with the absence of wheels makes it possible to easily work with soils on rows and beds without damage to already planted plants.

It is important to note that the cultivators “getting bad” with the cave-free soils, since when the first is the first to introduce into such a layer, the bar is sharply thrown back.

Taking this into account, many manufacturers equip disc cultivators with special safety covers, so there is a more chance that the toothed mills are more likely to bother than break.

However, in the latter case, at least a small protective panel for the legs will not be superfluous.

The presence of the safety screen significantly reduces the visibility of the employee!

Is it worth making a nozzle with your own hands?

The cost factor of the finished product is able to have a strong influence in the final choice, meanwhile to purchase a new nozzle-cultivator in the store or save and do it with your own hands. High-quality models for a trimmer for grass can be evaluated at 11-20 thousand.

This cost can only be justified if you assume large volumes of work with the tool! In addition, it is not worth buying an expensive device if there are heavy soils on the site, for example, loams and chernozems, since in this case the cultivator will not raise the ground, but it will only transfer the Комментарии и мнения владельцев to different places along with the roots of grass and weeds.

Choosing a nozzle, it is worth understanding the care technology: so the first thing you need to go through a nozzle-knife, breaking off all vegetation in the garden, after which you can proceed directly to loosening the earth!

Before you finally decide to make a chamber nozzle with your own hands for a trimmer for grass, you must first take into account the following points:

  • The execution of the handle. The long-term practice of using tools and research has shown that the most convenient in the work was and remains a T-shaped handle that provides the most reliable and accurate direction. The handle used in some gasoline trimmers in the form of the letter “j” significantly complicates the work with the cultivator nozzle;
  • The dimensions of the fuel tank. Since the nozzle for a trimmer for grass will be made of improvised materials, the overall level of fuel consumption will increase. Therefore, it makes sense to organize a tank with a capacity of at least one liter of fuel;
  • Drive power, which should not be less than 1000 watts. Otherwise, the engine will often overheat, which will lead to a low productivity of the device;

Homemade cultivator from a trimmer for grass and bicycle, a manual cultivator for processing a row

Earth cultivation requires a lot of physical effort. It is especially difficult to work with rakes and shovels when you have to cultivate a large plot of land. Do.it.yourself cultivators for soil greatly facilitate human labor. The technique replaces many devices and is suitable for processing the garden, vineyard and garden plot.

The principle of operation of the cultivator is simple: the element that loosen the ground begins to work after the mechanical part of the device is launched. Depending on the external size, engine power and performance, cultivators are divided into three types: light, medium and heavy equipment.

  • Light equipment is used in small areas with soft soil (flower beds, greenhouses).
  • Medium severity is used on clay soils.
  • Heavy equipment refers to universal equipment. It can be used for any soil.

Cultivators are of different types: disk, rotational, lap and milling. In terms of functioning, they can be: manual, with electric drive and working on gasoline, as well as trailed, hinged, process one or more rows.

When processing a land plot, everyone chooses the model you need. Hand cultivators are good in that they can be made independently with minimal cash costs.

From a trimmer for grass

A made cultivator from a trimmer for grass with your own hands will help to quickly and easily and easily and easily. You can assemble it from improvised materials: a working gasoline trimmer for grass, corner grinding or welding, garden forks, steel tubes.

  • For the manufacture of cutters, the teeth from the foriles are bent in the desired shape. Usually the soil is loosened to a depth of 10 to 15 cm, so the length of the teeth should be no more than 15 cm.
  • Next, we make the working part. The teeth of the foriles are flattened to the width of about 1 cm.
  • The mills are pulled with emery and fixed on a round heel.
  • A nickel with a diameter of 10 cm should be perfectly flat in shape. Mills in the amount of three pieces are located evenly on the heel. If you put more than three pieces, then the device will be strongly overloaded.
  • The final part is a connection of the base with cutters and a trimmer for grass. Well, if the shaft tip has a thread. Then the trimmer for the grass is simply screwed to her.

The technique is designed for loosening the soil at a small depth.

Nazadka-cultivator for a trimmer for grass. Is it worth buying?

When purchasing a gasoline trimmer for grass, owners of country houses and summer cottages receive a rather powerful and autonomous tool for various agricultural work. over, manufacturers often offer a variety of nozzles for them-black cutters, drying chopper, bluff Today we will talk in detail about the attachment-cultivator for the trimmer for grass.

Design and fastening options

Cultivator nozzle is in two versions:

  • Disk, whose cutting organs are a pair of cutting discs;
  • A gear, which is a number of milling on the shaft.

The fundamental difference is only in the design of the loose knot. Disk nozzles are more stringent, and therefore suitable for processing heavier soils, while the toothed ones have less their own weight, but are designed for work on lighter soil.

The transmission of the rotating moment from the engine of the trimmer for the grass for the hacker-cultivator is carried out using a special shaft, which is arranged in a special rod (it will have to be purchased separately).

This node is not interchangeable, and differs in the number of slots on the end part of the bar: there may be seven or nine.

Therefore, conceiving the acquisition of a cultivator nozzle, it must be understood that the OLEO-MAC factory is not suitable for a trimmer from Husqvarna, as if vice versa.

The slotted method of joining disks or cutting to the shaft allows the free movement of the cutting organs, which is ideal for cultivation, since it allows you to loosen the soil with a fairly wide capture (up to 200 250 mm per pass), without requiring a large amplitude of the rod movement. Restrictions on the density of the beds located on the site are also removed. With lengthening the beds of convenience of working with the nozzle under consideration, the turns will have to be done much less often.

Features of work by nozzle

Any nozzle-cultivator for a trimmer for grass significantly increases the weight of the entire device assembly (at least 5 6 kg). Therefore, long.term work with such a tool is not possible for everyone.

The calculation must also include mechanical restrictions on the power of the trimmer drive for grass.

If the engine is designed for a power of not more than 1,500 watts, then the cultivator can only be processed by regularly loosened soil, or limit yourself to hovering breasts, potato bushes, etc. P.

Since the drive of gasoline trimmers is located behind the worker, and the drive bar is quite long, vibrations constantly occur in the process of cultivation. Their value is determined by both the length of the bar and the change in the load on the wheels or cutters.

How to Edge beds like a PRO with this lawn Edger. Stihl Bed Redefiner

These vibrations through the shoulder belt are transmitted to the user’s hands, so it is not always convenient to control the trimmer button to turn on the trimmer for grass and hold the canopy.

Therefore, prolonged cultivation of soil using a cultivator nozzle is unsafe for health.

But not everything is so bad: the mobility of a gasoline trimmer for grass allows you to easily process the soil in the rowles, and the absence of wheels on a hinged cultivator does not damage plants on the beds.

Cultivator nozzle “does not like” creamy soil, and at the first introduction into such soil, the bar abruptly discards. Therefore, disk cultivators are equipped with a safety casing (gear mills are more likely to bend than break, although in this case a low protective shield from the legs would not have prevented). The presence of a safety screen worsens the visibility of a working with a cultivator.

Is it worth it to make a cultivator nozzle yourself?

The price factor has a noticeable effect on the choice: whether to purchase such a nozzle, or make it yourself. High-quality nozzles-cultivators for a trimmer for grass can be purchased at a price of 11,000 20,000, which justifies itself only with large volumes of work.

cultivator, trimmer, grass, your

It is inappropriate to buy such a node in cases where the processed soil is heavy (for example, chernozem or loam): the cultivator does not lift the soil, but only moves the lands from one place to another, moreover, along with the roots of torn weeds or grass.

The technology of vegetation care will also change: at first, a nozzle-knife should go along the beds, cutting off the grass, and only then use the cultivator nozzle.

Having made a decision on the independent manufacture of a cultivator nozzle to a trimmer, the following should first evaluate:

  • The design of the output section of the bar: if it is a flexible shaft, then you will have to forget about the cultivator: it will not withstand the amplitude of rotating moments. The cardan gear is more functional, and the most successful design is considered a multi.and.line rod, and a straight line, and not curved.
  • Drive power: if it is less than 1000 watts, then the engine will overheat, and cultivation performance will decrease sharply.
  • The volume of the fuel tank: energy consumption will increase significantly, since the cultivator nozzle will have to be made from improvised materials. Therefore, the tank should contain at least 1 liter of fuel.
  • The execution of the handle. Ergonomics experts believe that the most convenient is the T-shaped handle, which provides the most accurate and reliable direction. It is difficult to hold a gasoline trimmer for grass with a cultivator nozzle common in some models with a J-shaped handle.

If the existing trimmer for the grass satisfies the listed requirements, and its owner has sufficient experience in performing such work, then it is quite possible to make a disk nozzle with his own hands. As for the nozzles of the gear type, their independent manufacture is very time.consuming, and will not provide the desired quality.

Rimbage of potato beds using a trimmer for grass (motorcycle)

A classic trimmer for grass is an electric hand.bore, which is powered from a network or battery. Sometimes a trimmer is called a motorcycle- a more powerful lawn mower with a two- or four-stroke engine gasoline.

For design and purpose, these devices are very similar, but it is better to use motorcycles for processing the beds, since the electric trimmer motor is not designed for serious and long loads.

Sleeping potatoes with a trimmer in organic farming

While chemists are developing more and more poisonous herbicides, and weeds adapt safely for them, supporters of organic farming claim that the soil needs to loosen as little as possible, and traditional weeding is generally a useless occupation.

Buryan assimilates the beneficial substances with which gardeners fertilize the beds. If weeded weeds are carried away from the site, the Earth will lose some trace elements.

And if you cut the stalks of weed grass under the root (but only until the seeds are formed) and leave it to dry on the beds and in the aisles, they will play the role of mulch, attract useful worms and insects, detain moisture. Of course, after a while new shoots will break from the roots.

But only one weed will grow in the place of the cut, and if it is difficult to cut the root (and it is difficult to completely extract the roots from the ground when weeding), then a new plant will grow from each piece.

With the periodic mowing of the shoots of weeds, their roots will be exhausted and misunderstood, and there will already be nowhere to take the new weeds, unless the seeds will bring the wind. The exception is only the old dust, whose roots must be thoroughly lifted thoroughly, since they are able to pierce potato tubers through and through.

Another method of organic agriculture is sowing the Siderates. Rye, barley, oats, fatselia significantly improve the structure of the soil (and at the same time muffles weeds), but they need to be mowed when potato seedlings reach 15–20 cm in height.

Cut sidetric stems mulch the beds, and the roots die and rot during the season. It is more convenient and fastest to mow weeds or siderates with a trimmer: this is what is less likely to damage cultivated plants.

Trimmer nozzles for grass for weeding potatoes

For cutting weeds and siderates, it is better to use a motorcycle or a trimmer for grass, in which the electric motor is located in the upper part: then the device will be able to operate in wet grass. In the aisles, a trimmer head with a fishing line is usually mowed (rice.one). It is noted that weeds bended with a fishing line with a round cross section grow more slowly than after cutting with a cord with a cross section in the form of an asterisk.

Sometimes a three.lobed knife is used to cut weeds (rice.2). But metal knives are worn only on trimmers for grass with a straight bar, if it is curved, use plastic nozzles. The problem is that if the knife in motion stamps on a hard object, the trimmer for the grass will bounce back or even split. Models with a curved bar are equipped with plastic knives.

Sleeping potatoes with a motorcycle with a cultivator nozzle

Stores sell nozzles-cultivators for motorcycle cutters (rice.3). Cutters look like discs with bent blades worn on a common axis. As a rule, there are 4 mills in the nozzle.

The width of the nozzle, the diameter and quantity of milling plants directly depend on the power of the trimmer motor for the grass. If you use a too large cultivator, the engine can overheat.

Typically, the instructions for the nozzle indicate for which trimmers or motorized car is intended. If the power of motorcycles is less than 2.5 liters. With.

, But there is no cultivator in the kit, it is dangerous to use the nozzle purchased separately: this will significantly reduce the service life of the equipment.

It is not recommended to make the nozzle manually, since it is difficult to choose its width and diameter of the milling cutter so that the trimmer motor for grass does not suffer. In relation to Frasing, the same rule is valid as in relation to a knife for kosba: a collision with a solid object leads to a breakdown of motorcycles.

You can’t weave potatoes with a motorcycle or a trimmer on heavy, clay soils.

It happens that the Chinese nozzle for a trimmer for grass for weeding potatoes jams after 10-15 minutes of work.

To prevent an accident, experienced gardeners recommend carefully processing all the rubbing parts of the cultivator with silicone lubricant before the first use.

Rules for weeding potatoes with a trimmer

  • Before starting work, you need to put on glasses and a respirator: the cutters rotate very quickly, creating a cloud of dust and small scraps of grass;
  • Weave follows when the weeds are still very small and did not have time to take root properly. Since weeding with a trimmer takes several times less time than manual labor, it is better to process the beds every 7-14 days. When the tops of the potato bushes are closed in the ranks, weeding will no longer be needed;
  • For weeding, it is recommended to choose a sunny day. Then the weeds torn with the root during the daytime heat will fade and turn into mulch;
  • According to the principles of organic farming, it is impossible to deepen milling cutters more than 0.5–1.5 cm. With this method of processing, a dried crust is broken, and the upper soil layer in the beds is saturated with oxygen and nitrogen, which is very useful for tubers growth;
  • The mills cannot be deepened and because if you press the trimmer too much for the grass, the engine will overheat and break;
  • When weeding a trimmer with a low.power engine, it is recommended to take a break every 10. 15 minutes to let the motor cool;
  • At the end of the season, the nozzle is thoroughly wiped with a disinfectant composition (solution of chlorine, potassium permanganate or copper sulfate), since potato pathogens may remain on it. If there were cases of diseases on the site, then such an operation is performed after each application of the cultivator.

Repair of the nozzle and replacement milling

A broken cutter can be replaced by made independently by caring a circle from a sheet of metal, cutting out and bending the blades. But the diameter of the new part should not be larger than the diameter of the old. In no case should you put on the axis of the nozzle additional milling.

about how to weed potatoes with a motorcycle on the potato.

How to choose?

Buying a clogging nozzle for a lawn mower, in addition to the power of the engine of the benzotrimmer, they are based on several factors. This is the width of the processing, weight, diameter of the milling and the number of revolutions per minute. On average, the diameter of the milling cutter can be 20 cm, the number of revolutions is 180.

Considering that the nozzles for cultivating a gasoline trimmer are bad with a cave.like ground, you need to choose a disk.type option with a shield. At the same time, it is important to consider the care factor, because it is better to loosen the earth after its weeding. It is important that the handle is T-shaped, in this case the direction will be as reliable and correct as possible.

As for the design of the bar, it is useless to buy a cultivation nozzle for a flexible shaft, it will disable the unit quickly. An ideal option would be to buy a product with a multi.and.line rod paired with a cardan gear. Such an unit will show itself in work more efficiently and will differ in reliability. So that the engine does not overheat, it is important that the power is at least 1000 watts, otherwise labor productivity will decrease.

Features of operation

Given the capabilities of the trimmer for the grass and the nozzle itself, the work with the ridge is carried out until the weeds have not yet grown and strengthened. So, the user’s work will be more effective, because it is easier to cut low grass than to deal with rude and thick stems. Timely loosening of the soil with the help of a cultivator’s nozzle will contribute to accelerated growth and strengthening of planted crops and, as a result, high yield.

It is important to reliably fix the nozzle itself on the gasoline trimmer for the grass. It is important to take into account the fact that not every gardener can work with a motorcycle-cultivator, the reason for which is the weight of the braid for grass and hitch. If the unit engine is not designed for a power of more than 1,500 watts, this nozzle can only be used no more than a loot or light hill. It is important to understand that the nozzle for cultivating the soil by means of a benzo.cushion in no way replaces the unit for weeding, plowing and hilling. This is a mini-device for small purposes.

The knives rotating in the process are quite dangerous, and therefore, a gasoline trimmer should work extremely carefully. You can not try to clean the knives from weeds when the device is turned on. This can be done exclusively when the engine is completely stopped. Do not grab onto the knives with your hands or try to block them. It is timely to carry out the examination of the device, eliminating the breakdowns, as well as worn parts.

You need to refuel the unit on the street. It is important to ensure that there is no leak of oil or fuel. The engine should not be allowed. In the process, the operator should be away from rotating elements, since cutters can damage the limbs. Before starting work, you need to inspect the territory of future processing and save it from solid items. For example, it is advisable to get rid of stones that can cause a stop, or even a breakdown of milling.

If this happens, you need to immediately stop the unit and examine it for damage. You can’t work with a broken device.

You will learn more about the nozzle-cultivator for a gasoline trimer from the video below.

Design and fastening options

Cultivator nozzle is in two versions:

  • Disk, whose cutting organs are a pair of cutting discs;
  • A gear, which is a number of milling on the shaft.

The fundamental difference is only in the design of the loose knot. Disk nozzles are more stringent, and therefore suitable for processing heavier soils, while the toothed ones have less their own weight, but are designed for work on lighter soil.

The transmission of the rotating moment from the engine of the trimmer for the grass for the hacker-cultivator is carried out using a special shaft, which is arranged in a special rod (it will have to be purchased separately). This node is not interchangeable, and differs in the number of slots on the end part of the bar: there may be seven or nine. Therefore, conceiving the acquisition of a cultivator nozzle, it must be understood that the OLEO-MAC factory is not suitable for a trimmer from Husqvarna, as if vice versa.

The slotted method of joining disks or cutting to the shaft allows the free movement of the cutting organs, which is ideal for cultivation, since it allows you to loosen the soil with a fairly wide capture (up to 200 250 mm per pass), without requiring a large amplitude of the rod movement. Restrictions on the density of the beds located on the site are also removed. With lengthening the beds of convenience of working with the nozzle under consideration, the turns will have to be done much less often.

Features of work by nozzle

Any nozzle-cultivator for a trimmer for grass significantly increases the weight of the entire device assembly (at least 5 6 kg). Therefore, long.term work with such a tool is not possible for everyone. The calculation must also include mechanical restrictions on the power of the trimmer drive for grass. If the engine is designed for a power of not more than 1,500 watts, then the cultivator can only be processed by regularly loosened soil, or limit yourself to hovering breasts, potato bushes, etc. P.

Since the drive of gasoline trimmers is located behind the worker, and the drive bar is quite long, vibrations constantly occur in the process of cultivation. Their value is determined by both the length of the bar and the change in the load on the wheels or cutters. These vibrations through the shoulder belt are transmitted to the user’s hands, so it is not always convenient to control the trimmer button to turn on the trimmer for grass and hold the canopy. Therefore, prolonged cultivation of soil using a cultivator nozzle is unsafe for health.

But not everything is so bad: the mobility of a gasoline trimmer for grass allows you to easily process the soil in the rowles, and the absence of wheels on a hinged cultivator does not damage plants on the beds.

Cultivator nozzle “does not like” creamy soil, and at the first introduction into such soil, the bar abruptly discards. Therefore, disk cultivators are equipped with a safety casing (gear mills are more likely to bend than break, although in this case a low protective shield from the legs would not have prevented). The presence of a safety screen worsens the visibility of a working with a cultivator.

Mounting methods and design

Modern nozzles-cultivators can be performed in two performance:

Homemade CULTIVATOR for TRIMMER ?! Easy Hack TRIMMER! TEST

Despite different names and designs, by and large the fundamental difference is only in the form of a loose knot.

Rosted nozzles for a trimmer for grass differ in a smaller mass, and therefore are better suited for processing light soils. As for disk models, they are used to loosen more heavy soils, as they have greater stiffness.

The torque is transmitted to the nozzle-cultivator from the engine thanks to the shaft, which is combined by means of a special bar. The latter, unfortunately, often has to buy separately.

cultivator, trimmer, grass, your

The unit under consideration cannot be called interchangeable, while the number of slots on the end part of the bar may vary from 7 to 9. Based on this, buying a cultivator nozzle, for example, from Oleo-Mac it is worth knowing that it is not suitable for working with the Husqvarna trimmer, as vainly.

The slotted method of fixing the cutter or disks to the shaft provides for a free displacement of the cutting organs, so that the soil will be loosened with a fairly wide coverage-200-250 millimeters. This option is perfect for the purpose of cultivating the Earth on the site, since it eliminates the large amplitude of the bastard of the bar during operation. In addition, this method allows you to reduce or completely abandon restrictions on the density of the beds.

When processing long beds, the process of working with a nozzle and a trimmer becomes even more convenient, since in this case you will have to make turns much less often.

Nuances when working with a cultivator nozzle

It is important to emphasize that any kind of nozzle significantly increases the mass of the entire tool as a whole, and weight growth is often at least 5-6 kilograms. That is why prolonged work with a trimmer in this case becomes far from far from everyone! In a series with this, when choosing a nozzle, it is important to consider mechanical restrictions on the power of the device drive. For example, if you have chosen a model of a trimmer for grass with a engine of less than 1,500 watts, then when processing the soil, you will have to limit yourself only to hilling of potatoes and beds, since it will be possible to work only with regularly loosened land!

Since the drive bar has a considerable length, and the drive itself in trimmers operating on gasoline is usually placed behind the worker, then in the process of cultivation of the work they are accompanied by noticeable vibrations, the value of which can vary depending on the load on the cutters and wheels, as well as the length the bar itself. Through the shoulder belt, the vibration data are transmitted directly to the person’s hands, and therefore it is difficult to hold a considerable node and at the same time control the button of soil cultivation is difficult. Given this, it is important to emphasize that prolonged soil processing with a cultivator nozzle does not always remain safe for human health.

But there are advantages: so increased mobility of a hinged gasoline trimmer for grass with the absence of wheels makes it possible to easily work with soils on rows and beds without damage to already planted plants.

cultivator, trimmer, grass, your

It is important to note that the cultivators “getting bad” with the cave-free soils, since when the first is the first to introduce into such a layer, the bar is sharply thrown back. Taking this into account, many manufacturers equip disc cultivators with special safety covers, so there is a more chance that the toothed mills are more likely to bother than break. However, in the latter case, at least a small protective panel for the legs will not be superfluous.

The presence of the safety screen significantly reduces the visibility of the employee!

Features of use

When using attachment cultivators installed on gasoline trimmers for grass, it is necessary to take into account a number of important nuances:

  • Before use, it is recommended to check in advance the strength of the fastening bracket for nozzle-cultivator.
  • A tank with a fuel trimmer for grass should be completely seasoned.
  • It is recommended to moisturize the soil with water for its partial softening.
  • When buying a trimmer for grass with a nozzle, it should be used in sparing mode at low speeds until the end of the running.in, which lasts about 20 hours.
  • Immediately after running in, it is recommended to replace the oil in the engine.
  • In case of vibration, you should immediately stop the work, as this may indicate a weakening of fastening the nut or deformation of the cutter, which causes eccentricity.
  • After each use, it is recommended to rinse mills from adhering clay and other types of soil.
  • Given the low power and motor resource, it is not recommended to operate the cultivator in the ground for more than 40. 60 minutes without a break, for cooling the impeller.

Possible difficulties in applying

Given that the trimmer for grass is initially not intended for loosening soil using a cultivator nozzle, when working with such agricultural equipment, some difficulties may arise:

  • Insufficient engine power. the cultivator cannot effectively loosen dense soil.
  • A significant weight of a trimmer for grass, which is required to be on weight, which makes its use limited to people with weak physical training.
  • Quick overheating and increased load on the power unit, which leads its physical wear.
  • When installing a home.made cultivator, in the case of a trimmer breakdown for grass, the manufacturer’s warranty is removed from it.
  • It is required to resist the bar to deepen the working body into the ground, which leads to deformation of the main parts of the technique.
  • A trimmer for grass with a cultivator nozzle can be injured in case of non-compliance with safety precautions, which requires extremely careful handling of it.

Can you make a device with your own hands?

In some cases, the owner of a summer cottage does not have the opportunity to purchase an original cultivator nozzle for his trimmer for grass. In this regard, a detailed description of the manufacturing scheme for this attachment equipment from improvised materials and using a standard set of simple tools is carried out below.

What is required for this?

In order to independently make a cultivator-cultivator for a gasoline trimmer for grass, it is necessary to stock up in advance with the following materials, consumables and finished products that can be purchased in any construction market:

  • A penetrated steel plate with dimensions 150. 200 x 40. 50 mm with a frequency of openings from 20 to 30 mm and a thickness of up to 3. 5 mm.
  • A set of two galvanized bolts with washers, nuts and counter.hacks with M10 thread sizes and 45. 50 mm long.
  • A sheet of galvanized or black steel from which a protective wing is made.
  • Corner grinder for cutting metal.
  • Drill with a drill for metal for the installation of holes for fasteners.
  • Roulette and ruler, as well as a marker for removing measurements and marking.
  • File for processing the ends of the metal plates after cutting.
  • Plafers and hammer for metal deformation.
  • Washing cry for tightening bolts and nuts.
  • It is also recommended to use hammer paint for the preservation of the future product from corrosion.

It should be noted that all materials should be of high quality, do not deform when the load is applied, which will significantly increase the period of uninterrupted service of the finished nozzle.

Step.by.step instructions for manufacturing

To assemble a home.made nozzle from the above materials, no appeal to professionals is required. All work can be quickly done with your own hands. Subject to thoroughly compliance with all points of the next step.by.step instruction:

  • The rectangular plate is available to find its geometric center.
  • A hole is drilled in the center of the plate for its fastening on the pin.
  • In the diametrically opposite direction, two holes for bolts with nuts are also drilled.
  • The second plate for the protective wing is cut along the radius, until the shape of the disk is reached, after which the holes are drilled strictly until the main rectangular plate is completely coincided with the penetration.
  • The entire structure is assembled. the rectangular plate is applied to the radius casing, after which bolts with nuts are delayed in the places of holes along the edges of both parts.
  • The central opening of the structure is planted on the heel of the trimmer for the grass and tightened with a fixing nut.
  • If necessary, on a steel casing, you can also perform up to 16. 24 small holes for bolts with a thread diameter of up to 3.5 mm and a length of up to 40 mm.
  • When working, the cultivator is held in such a way that the disk nozzle is parallel to processed soil, and, during rotation, the bolts, ensure its loosening to the entire depth.

Homemade protective casing

If a homemade mower is made by you, then you will definitely need a protective casing. He will protect your eyes, body and legs from injury with small pebbles and fragments of knives if they break.

A trimmer for grass can be made from a sheet of aluminum or thin tin.

  • At first, in the corner of the square of the metal it is necessary to drill the hole of the desired diameter (depending on the type of drive of your unit) using the crown.
  • Then you need to make markings for fasteners. As a basis to which homemade protection will be screwed, you can use a standard casing from corner grinding, if you make a trimmer for grass from it.
  • Close the workpiece with a clamp and using a tape measure and a pencil, draw the first circle with a radius of about 270 mm. The center of the circumference will serve as the corner angle. It is impossible to give accurate recommendations about the radius, since it will depend on the diameter of the cutting tool that you will use with the unit. Therefore, first decide which knives you will use, and which fishing line will be optimal.
  • Next, conduct a second arc (this will be a bend), slightly retreating from the first. In this case, 5 centimeters. Thus, you measured the height of the future shield. In general, the height of the casing is recommended to be done so that when you put it exactly on the ground, the cutting tool does not reach it about 2 cm.
  • After marking the second line, it is necessary to cut the workpiece along it, using a hacksaw for metal or an electrician with a file on metal.
  • In addition, it is necessary to make radial cuts (to the first arc) and bend the resulting parts with pliers at an angle of 90 °.
  • Further, the shield is attached to the protective casing of the corner grinding, the cutting tool is installed, and the unit is ready to work.

In this way, you can make and install a protective casing and on a trimmer purchased in a store if the shield has split for some reason. The shields in the factory devices are made of plastic and often break if you unsuccessfully hit the head of the trimmer for grass on the ground for lengthening the fishing line.

Power for a trimmer for grass

For more comfortable work with a trimmer, if it is understood to process a large area overgrown with grass, it is advisable to use a special belt. This device relieves fatigue from the hands and back of the mowing operator and greatly facilitates the process when compared with the same work, but without a belt.

Belts are shoulder and ranger. The shoulder belt is the simplest device and consists of a loop with two or one latch (carabiner), with which it is attached to a mowing unit. A plastic plate is usually attached to the second carbine, which protects the side of the operator from pressure with a bar trimmer for grass.

Shoulder belt is usually used with light trimmers weighing 3-4 kg. For heavier units, it is more convenient to use a parapier belt.

A belt for a trimmer for grass can be easily ordered via the Internet or buy in a specialized store where these devices and components are sold to them.

and higher.

If there is a desire to do it with her own hands, then any mistress, looking at this device, can easily sew it from improvised means (old belts and belts). You may have to buy buckles and carbines. But still, we recommend buying a ready.made ran.out suspension and not waste time and money to make the worst quality than ready.made devices.