Disk installation on Champion gas station. How to put a disk on a lawn mower properly

Criteria for choosing discs for trimmers for grass and instructions for replacing them

Trammers’ grass ugos occurs due to the use of a mowing head with a fishing line and metal disks. Each type of cutting device has its own fundamental features. The use of the fishing line is limited to the type of vegetation, therefore, where the head with the cord does not cope with the task, a metal disk is used. How to choose a cutting disk for a trimmer for grass, what they are, and how they are hidden, we find out the details before buying an appropriate equipment.

Initially, we note that metal discs can be used not only on gasoline, but also electric trimmers. The main condition for the use of metal cutting knives on the equipment. in the design of the tool, the transmission mechanism (shaft or gearbox) should be a rigid type. A hard.type gearbox is a metal shaft transmitting a torque from an electric or gasoline engine to a working organ.

There are models of trimmers with flexible shafts, the design of gearboxes in which is represented by a steel cable. These are, as a rule, low.power electrical grass drivers that are not intended for large loads, as well as household lawn mowers. You can’t use metal disks on trimmers with a flexible shaft (only plastic), as this will lead to a rapid failure of the gearbox. Before buying metal cutting mills, you will need to find out the type of gear ratio of your tool. hard or flexible.

What type of gear ratio is used on the trimmer is indicated in the technical description to the tool. If a trimmer for grass has a curved bar, then a flexible shaft is used in its design. Tools with direct bar can be equipped with rigid and flexible gearboxes, which depends on the power of the trimmer for the grass.

Trimmer knives are classified according to the following signs:

• Manufacturing material. they are plastic and metal. Plastic knives are less effective than metal, but they do not have a large load on the shaft and the drive mechanism of the tool. Plastic discs are used on electric trimmers and household benzos
• The design of cutting devices. Steel discs are of two types. blade and toothed (milling). Plastic knives are produced in the form of blades. Tough devices have a similar design with circular discs, and lobed have large flat knives
• The number of cutting edges. The number of teeth and knives on the disks differs, which affects the performance of cutting equipment. On gear discs, the amount reaches 80 links, and on blade. from one to four pieces
• The presence of additional spraying. steel gears are additionally equipped with winning attacks, which allows you to use a tool for driving grass on mound surfaces. When the disk is contacted with obstacles in the form of earth and stones, the teeth are not deformed and do not dull, which is achieved due to the presence of winning attacks. Experts say that devices with carbide attacks do not serve for long. Attacks wear out quickly, and then the milling cutter is used without winning

Plastic knives for trimmers not only cost cheaper than metal ones, but also do not have high loads on the engine and transmission mechanism. This is especially true when the knife stumbles upon obstacles. The higher the elasticity of the cutting knife, the less likely the deformation of the plastic disks.

It is interesting! Rosted wheels with a large number of links are used to prick different grass. dry, green lawn and thick.nisted. The cut with such a disk is straight, clean and even. In addition, a large number of teeth excludes their rapid dullness, and the presence of additional holes on the surface of the circle (penetration) is intended not only for cooling, but also to reduce weight and increase inertia.

The advantages of trimmer disks compared to the fishing line

Trimmer disk compared to the cord, has its advantages. You need to know these advantages in order to decide in the end whether to buy and use metal cutting knives. Consider all the advantages of the trimmer disks:

• The ability to cope with different vegetation, unlike fishing line. It can be dry, long and thick.nisted grass, and even small vegetation. The fishing line for a trimmer hardly copes with medium.sized grass, and it is not able to cut off thick.stubble grass. The cord will either get confused for the grass, or the fishing line for the trimmer will wear out quickly, which is not at all rational
• High speed achievement of the result. Unlike fishing line, the disk cuts grass with qualitatively (with good sharpening), without leaving “roosters”, therefore, a mowing trimmer with a metal circle occurs faster than when using the cord
• Discs do not wear out, unlike the cord. The cutting knives or parts of the circle are blunted, but the issue is resolved by hiding. How to sharpen a trimmer metal circle described in the material below. With prolonged operation, the cutting devices are abrasion, but they are enough for at least 3-5 years
• A long service life, in contrast to the fishing line, which is associated with the design of the equipment

There are also disadvantages of the considered cutting devices for trimmers. The first drawback is that it is impossible to work with a disk tool when the grass is performed next to obstacles in the form of trees, buildings, stones, shops, etc.P. When a disk collision with an obstacle, the drive is inhibition, which is reflected in the form of such minuses:

• The engine overheats
• The cutting parts of the disk that are blunted are damaged
• Transfer mechanisms. flexible and hard shafts (gearbox) come out of order

If you plan to mow thick grass in the field, then do without a trimmer for grass with an installed metal disk, it is impossible. The fishing line for a trimmer is used to prick small grass in personalities near obstacles.

It is interesting! On trimmers with a curved rod structure, you can not use steel discs due to safety. If the disk attaches an obstacle, then the effect of returns arises, through which the cutting part can fall under the feet of the operator. As a result, the operator risks getting serious injury.

Review of species

For motorcycles, preference should be given to special knives. They allow you to mow higher and hard grass than a fishing line for a trimmer. In addition, the knife is suitable even for trimming young bushes.

There are many types of discs that differ in the cutting edge, shape and material from which.

On the performance of the cutting edges

• with two teeth. for young soft grass, lawns;
• with three teeth. for young grass, dry, weeds;
• with four teeth. for hard grass and young shoots of trees;
• with eight teeth, mow grass without severe grinding;
• with 24 teeth-for hard and dry grass, shrubs, thin trees;
• with 40 or more teeth. for mowing of any grass, bushes, trees;
• with the 80th or more-for professional motorcycle.
• with two. for soft and low braids for grass;
• with three. for mowing weeds;
• With four or more. for mowing grass on hay.

By form

The form distinguishes knives with disk canvases and several blades that are at a certain distance with each other. The shape of the blades may also differ. It is worth noting that this does not affect either speed or quality of work with a motorcycle.

Currently, manufacturers began to offer, in addition to traditional forms, still triangular, rectangular and trapezoidal.

According to the material

A disk for a lawn mower can be made of metal or plastic. It should be clarified that for electric motorcycles it is worth giving preference to plastic blades. They are excellently suitable for a curved rod of this tool, which does not separate the working area and legs of the mowing. Plastic knives are able to spin well with outgrown dry grass, for example, nettles or burdock trunks.

Metal knives are suitable only for a gasoline trimmer for grass. This is due to a flat bar, which removes the disk from the legs to a safe distance. Safety also contributes to the handles of a special shape. When impact on a hard object, part of the impact is extinguished with a clutch clutch with a clutch. Iron knives are suitable for mowing grass from large areas, weeds, shrubs, young trees.

Review of manufacturers

Motokos disks manufacturers are a huge number. It is worth familiarizing yourself with the most popular among them. For example, the Bosch brand is known for its knives with two and three blades. The peculiarity of the knives of this company is that each of the blades can be replaced separately from the others.

Another company, known for its lobed knives, is a “shark”. The advantage of the design is that the blades are fixed relative to each other at an angle of 120 degrees. As a result, it is easy to configure each of the blades, which is convenient for different vegetation. Another feature of the knives from this manufacturer is small weight.

Husqvarna is also known for its knives with many teeth, especially hay knives. Ideal for thick and dense grass. Of the minuses, it is worth noting the large weight of the disks and the fact that you can not turn the knife if one side is imprisoned.

InForce knives cope well with undergrowth and branches. In practice, the metal from which the cutting elements are made shows itself as a very strong. The only thing in some models of winning attacks are erased very quickly.

Positive reviews often receive knives from Maruama. They are characterized as very strong and durable.

Discs do equally well as grass of different types, so with shrubs and trees.

Rezer discs perfectly cut grass, weeds, branches. The teeth can withstand even drilling trees with a thickness of 6 or more centimeters. However, they have a lack of winding grass on the shaft.

Patriot company produces high.quality knives. Users note that if you choose the right disk for a certain job, then it will serve for a long time and surprise with its performance. It is very easy to drag knives from this manufacturer on your own.

A knife installation algorithm for a trimmer for grass

Replacing the knife on the trimmer is quite simple. In the kit with it, manufacturers include the key to remove the cutting nozzle (spray with a fishing line) and a pin designed to block the gearbox. To change the disk, you need to perform the following actions:

• remove the casing that performs protective functions;
• insert the pin into the combined holes located on the shaft and gearbox, and in this way block the drive;
• If a spool with a fishing line is installed, then it should be unscrewed along the time of time and find a nut to tighten the knife;

In detail the algorithm for installing a knife on a trimmer for grass is demonstrated in the video further.

Modern trimmers for grass, for example, from the company “STIHL”, are easy to maintain. Conduct the replacement of cutting parts on your own will not be difficult.

When working, you should pay attention to safety measures so as not to cut.

How to sharpen a disk if it is dull

Motokos are designed for mowing grass, shrubs and young trees. The quality and productivity of the work depends on the severity of the blades. Over time, knives are blunting even with winning attacks. In this case, you can go in two ways:

To properly sharpen the knives, act as follows:

• Gently disassemble the trimmer for the grass, removing the cutter;
• examine it for cracks that make further operation impossible;
• If the blades are bent, then they are aligned using a hammer;
• reliably clamp the blades, not too much, but so that they do not move;
• Based on the size of the disk, choose a file for metal so that it is convenient to work;
• to the same extent (at an angle equal to 30 degrees), all cutting (upper) edges of the knives are pulled;
• The lawn mower is assembled in the reverse order.

Disks with an attack of solid materials are only changed to new ones, but do not sharpen.

Sharpening can be carried out on an emery machine at low speeds. this will accelerate the workflow. At the same time, a grinding circle with the average grain size is used to work. Knives should be sharpened, having previously put on gloves and glasses.

For motorcycle, plastic and metal cutting nozzles with different number of blades and sharpening are used. These factors determine the sphere of application of knives. Therefore, they should be selected, given the nature of the upcoming work. Replacing and sharpening the discs of a trimmer for grass should be carried out carefully so as not to get injuries. There is nothing complicated about it. Only a way to fix the milling on old models can differ, therefore, it may be necessary to use another tool.

Gasoline gas mowing gasoline with butter

Before mowing grass with a benzo.leggos, it is necessary to season the tool with fuel. As fuel, gasoline with butter is used. However, take into account that mixing gasoline with oil is needed only for two.stroke engines. Four.stroke engines operate on pure gasoline, since their design has a separate container. oil crankcase. There are no 2-stroke gas crankcases in the design of the 2-stroke gasolimers, so you need to pour exclusively gasoline with butter in the tank.

As gasoline, it is recommended to use AI-92 brand fuel. In order not to make a mistake in choosing, you need to read the instructions offered by the manufacturer. Often, most manufacturers recommend using the AI-92 brand fuel, and only some recommend filling AI-95.

Gasoline must be diluted with a small one in a proportion of 1 to 25. This means that 40 ml of two.stroke oil must be added per 1 liter of gasoline. However, not everything is so unambiguous here. The proportion 1 to 25 is universal, but each tool model has its own values. These values ​​are also indicated by the manufacturer in the instructions. details about how to properly dilute gasoline with butter into a lawn mower is described here. After breeding gasoline with butter, pour a full tank, and start work.

It is interesting! If a four.stroke lawn mower is refuel, then pure gasoline must be poured into the tank, and engine oil is added to the oil container to the maximum level.

Instructions on how to use a gasoline trimmer learning to start a tool

Before working as a tool, it must be initially started. How to get a lawn mower, consider in detail. First, the tool should be placed on a flat surface so that the disk fixed to the shaft does not cling to anything. After that, we proceed to the launch of the engine of the lawn mower:

• Initially, fuel should be swollen into the launch system. To do this, press 4-5 times on a primer (soft hemisphere on a carburetor)
• Next, transfer the carburetor switch to the “OFF” mode. This switch is responsible for opening and closing the air damper. The transfer of the switch to the “OFF” mode allows you to make the fuel mixture during the launch of the enriched
• There is a switch on the handle near the accelerator. He is responsible for turning on and disconnecting the ignition. Before starting, you need to transfer the ignition switch to the “1” mode
• Now you can launch. To do this, you need to hold the tool with one hand, and the second sharply pull the starter handle. If the engine braid engine did not start the first time, then do not despair. Attempts to start the start until the engine starts. Typically, for this, 2-3 repetitions should be performed
• If the engine does not start after 5 repetitions, then the fuel suction should be repeated using a primer, and start starting again
• As soon as the motor starts, you need to transfer the air damper switch to the “ON” mode. This means that a mixture of fuel with air enters the cylinder
• Let the tool work for 15-30 seconds at idle while the engine warms up, after which you can proceed to the span of grass

The above instructions for starting the engine and trimmers are appropriate for a cold start. If in the process of operation the tool was a pause, then when re.starting the non.surviving engine to close the throttle, there is no need. It is required to simply turn on the ignition, and pull the starter handle.

It is interesting! If the lawn mower is new, then do not forget that it is impossible to work at full power until the running.in procedure passes. This is important to consider, otherwise the engine details will quickly be worn out and will fail.

The main malfunctions of the starter of the trimmer for grass

It is not difficult to determine the cause of the breakdown of the starting device. There are several main options:

These details are shown in the photo below.

It may happen that the starting mechanism will be accidentally broken. The consequences will turn out to be deplorable if the ragged rope is wound around the flywheel of a working internal combustion engine: then the spring bursts, the pulley will tear off. But such cases when a complete replacement of the starting node is required, they rarely occur. In most cases, to fix the mechanism, it is enough to put a new spring or replace the cord.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work, you will need a screwdriver with the tip of the desired shape.

Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.

Parsing the starting node

They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:

• spin a screw with a screwdriver, fixing the pulley with a starter lid;
• take out a spring and antennae;
• Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
• determine why the launch mechanism has broken;
• If the spring collapses almost completely, then it is replaced;
• When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);

To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst. Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges.

Immediately putting a springy plate in the same place does not always work. It often slips, so attempts are required to repeat until the desired result is achieved.

Starter assembly

The assembly of the starting node is carried out in a number of stages:

When making the stated manipulations, it is necessary to lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled. Because of this, a feeling appears, as if the spring had flown. To eliminate such a drawback, you need to install this part of a larger length or an additional goal.

When such spare parts are absent, you can just unscrew the screw a little, and the starter knot will begin to work without shaken. But this option is temporary. it is better to repair qualitatively as quickly as possible.

Spring tension

After installing the spring, it should be pulled. The following actions are performed for this:

• Remove the handle from the starter cord;
• Then the rope is inserted into the coil groove;
• They stretch the spring, rotating the coil in the direction opposite to the clock of the clock arrow (reviews);
• make the desired number of revolutions specified in the instructions for the use of the trimmer model used and the corresponding length of the cord used;
• At the very end, the rope is threaded into a hole designed for this, located in the starter cover;
• put the handle in place, fixing it with a node.

If after the repair the spring continues to fly, then you can get rid of this in the following ways:

• Squeeze the suitable piece of the plate into the groove at the location of the spring hook;
• drill holes on two sides of the groove in the coil, into which the spring hook is inserted and fix it using a wire.

Replacing a torn cord

A torn rope is replaced in the following sequence:

• The old cord is removed;
• choose a suitable rope (thickness and length);
• Having reached it through a special hole in the coil, a knot is tied;
• Sprinkle a spring, producing the required number of revolutions;
• Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way. In this case, there are some nuances associated with their constructive features.

How to correctly install a disc on a trimmer for grass

Disks for the lawn mower: what are they, how to choose and install?

Knives for motorcycles. inconspicuous thing. Enough to choose the right one, and you can mow with their large sections of the grass. Naturally, the abundance of knives somewhat complicates the task of their selection. To realize what specifically cutting element is needed, you need to familiarize yourself with the main of their. Also, in advance, it should be found out about the proper sharpening and operation of knives.

Review of species

For motorcycles, preference should be given to special knives. They allow you to mow the highest and more rigid grass than a fishing line for a trimmer. In addition, a knife is suitable even for trimming young bushes.

How to choose?

When choosing a knife for a mower, you should pay your attention to many points. For example, wheels with metal teeth in most cases are made in the form of a circle. Teeth can differ in shape, species, size. For small trees, it is also better to give preference to discs with a huge number of teeth.

It should be noted such an advantage of milling circles for motorcycle circuits as a frisky set of revolutions. But the highest moment of inertia does not best affect the drive device of the unit. For dense mowing, for the highest, also for small rough grass and shrubs, it is better to choose circles with 40 and more teeth and penetration. They are able not to grind vegetation, and with all this it will actually not be wrapped in a circle. If the number of teeth is more than 60, then you can safely mow grass and trees with a trunk width up to seven cm.

Disks with a solid canvas and without holes are distinguished by a large mass, so they should be chosen for massive trimmers (more than 40 cm3). With all this, it is comfortable to mow the rare grass, dry, they are also suitable for mowing with different density.

Winter attacks should be chosen for mowing plants next to obstacles. If you need to mow grass on hay, then you should give preference to iron knives with a huge number of teeth with even sharpening. Continuous discs with the number of teeth from sixteen to 30 two perfectly cut plants with thick trunks.

For low.power trimmers, lobed discs with the least moment of inertia are better suited. The smaller the blades, the stronger the tool will grind the grass. So, discs with 2 blades in most cases are used to mow homogeneous grass. The main advantage of this species is that it discards cut plants to the side.

The thickness of the blades is also fundamental when choosing. Discs can be stamped or forged. The 1st differ in a low price, but with all this they can be very damaged, faced with an obstacle. As for the forged discs, chips and slices do not form on them when colliding with hard objects.

For electronic trimmers, only plastic knives should be selected. Their low weight will not create an excess load on the engine. Soft plastic allows the knives when they are on the obstacle do not break, but simply bend a little or deform. It is recommended to use such cutting elements for a beard of thick soft grass.

Review of manufacturers

Disk manufacturers for motorcycle unlimited number. It is worth familiarizing yourself with the most popular in the middle of their. For example, the Bosch trademark is known for its knives with 2 and 3 blades. The peculiarity of the knives of this office is that each of the blades can be changed separately from others.

Another company, popular with its lobed knives, is a “shark”. The advantage of the design is that the blades are fixed relative to each other at an angle of 100 20 degrees. Ultimately, just configure each of the blades, which is comfortable for different vegetation. Another feature of the knives from this manufacturer is small weight.

When it is necessary to adjust

Carburetor adjustment is necessary in the following cases:

• The new engine was running out (4-5 liters of fuel mixture were used);
• The composition of the fuel has changed (brand of oil and gasoline);
• The weather changed (it became hot, cold);
• Air vacuum has changed (concerns mountainous areas);
• after long.term storage;
• the load on the engine has increased (after changing the tool and t.D.);
• Due to the vibration, the adjustment screws spontaneously unscrewed;
• Fuel consumption has increased, the carburetor shimmers the fuel;
• Flapse quickly appears on the electrodes of the candle (while the fuel mixture is prepared correctly);
• The motor starts and immediately stalls or is poorly gaining momentum;
• Gasoline does not enter the cylinder;
• A large amount of exhaust gases.

How to properly adjust

Before setting up the carburetor trimmer for the grass, it is necessary to do the following:

• Rinse the engine;
• replace or clean the spark plug;
• change to a new one or clean the air filter (it is recommended to lay it out in warm, soap water, squeeze it out and let it dry well).

It is also necessary to install the cord of the right diameter in the trimmer coil or install knives-this is done so that in the process of configuration the engine has at least some load. After installing a cutting tool and starting a gasoline engine, let it warm up for 10 minutes.

If at the idle speed of the motor you noticed that the cutting tool rotates, then it is necessary to reduce engine speeds. This is done using the lower idle regulator, often marked with the letter “T”. The figure below shows the placement of regulators on the trimmer Husqvarna.

But, for example, on the STIHL trimmer, this screw may have a label “LA”.

So, turn the idle control regulator to the left, until the trimmer head is completely stopped.

To configure the carburetor, 3 regulators are used (screw).

• The right regulator L tunes the level of enrichment of the combustible mixture at low speeds. It needs to be adjusted by the first. Get a maximum of turnover at idle. This is done using the regulator L, turning it to the left and right. After finding the point of maximum revolutions, return the regulator for half a turn to the left (against h. Arrows).
• The lower regulator t (LA) is used to configure idle. Turning it to the left, the engine speed will begin to decline, and when the regulator is turned to the right, the revolutions will increase.
• Left regulator h is responsible for enriching the combustible mixture at high speeds. The enrichment configuration completes the adjustment of the carburetor. Also, using this regulator, you can configure maximum speed, fuel consumption and engine power.

Important! If you allow the engine to operate at full speed for more than 10 seconds, then it may fail.

To exclude this trouble, adjustment will be required. With the working motor, give a full gas, then turn the “h” regulator to the right until a reduction in revolutions begins. After that, the “h” regulator must slowly scroll to the left until you hear the uneven operation of the engine. Then the regulator “h” should be rotated to the right until the moment of flat operation of the motor is heard.

After conducting the above actions, the setting of the carburetor can be considered completed. After proper adjustment, the engine must confidently gain momentum, a little four at a maximum of revolutions, and when working, an idle cutting tool should not turn. This manual is suitable for adjusting carburetors on the Huter, Patriot and others benzocos.

There are also carburetors without a screw that is responsible for enriching the combustible mixture at low speeds. That is, they have only 2 adjusting screws: a idle regulator and a quality fuel mixture regulator at high speeds. How to configure a carburetor of this type, you can find out from this video.

The knife does not mow even with sharpening. Correct

The method of installing a knife on a trimmer for the grass is subsequent:

• Remove the protective casing;
• We block the drive. For this purpose, you need to cooperate two holes. in the shaft hub and in the gearbox cup. After combining them, insert the pin into the holes;
• We unscrew clockwise the spool with a fishing rod with a fishing line or a mounting nut that holds the boot (if the trimmer for the grass has not yet been used);
• Then we install the cutting knife, such a macar that the hills on the puck coincide with the notchs in the hole of the cutting disk;
• Install the boot;
• We twist the mounting nut (counterclockwise) holding the stopped pin;
• We tighten it using a tubular key;
• Return the protective casing to its destination.

As you can see, there are no difficulties. Now there is an option to boldly start the mowing of a weed in this area.

Motoburg and ice car from the lawn mower

When installing fences and fence, it is necessary to make round recesses in the soil, which are needed to fill concrete or metal columns. A manual drill is a certain tool, but if it is necessary to make a large number of holes in the soil with time limitations, you will need third.party assistance led by the engine from Motokosa. The material on the link presents a motorbike from a chainsaw, but if there is only a lawn mower at the disposal, then this useful tool can also be made of it. Motoburg nozzle for grass is presented in the photo below.

The operator can only attach a gasoline engine to the device, and proceed to the operation of drilling holes in the ground. It is important to understand what to use for such a nozzle, powerful engines from benzos should be, otherwise it will lead to their overheating and rapid wear of parts.

In addition to the fact that a trimmer for grass can be used as a motorbike, it can still serve as an ice discovery, which is especially true for winter fishing. This material describes the process of manufacturing an ice.block from an electric screwdriver, but using the engine from a trimmer for grass in a pair with a special nozzle, it will be much easier to cope with the task of drilling holes in the ice.

It is interesting! The nozzle of the ice.beam from a trimmer for grass copes with drilling holes in the ice effectively, but its main disadvantage is the noise when operating the engine.

Metal brush to clean the surface of contaminants

You can also use a trimmer for grass as a construction tool. If it is necessary to clean the metal surface of various kinds of pollution, then you should use a conical butt brush. It is also used to clean concrete surfaces and slate. The peculiarity of such devices is that they allow you to clear the most inaccessible areas at the site of joints and angles.

The brush has a similar design with nozzles for angular grinder, only intended for use in a pair with a trimmer (its diameter is 200 mm).

The brush is attached to the trimmer instead of a spool, and for this you will not need to remove anything, redo or invent. The design provides not only easy installation, but also ease of use. The casing protects the operator from flying stones when working as a nozzle.

Other types of nozzles for a trimmer for grass are also known, through which you can not only expand the functionality of the tool, but also facilitate physical labor. The material discusses not only the main and popular nozzles for motorcycle, but also the safest. over, they are harmless not only for a person, but also for the tool itself.

Summing up the nozzles for motorcycle and trimmers, it is worth noting that the relevance of their use depends on the type and volume of tasks. Do not forget that the excessive loads that shaft on the shaft, adhesion and the drive of the tool contribute to their accelerated wear. That is why it is important before the purchase of devices that expand the functionality of the benzo tool, to decide on the need to use them.

The material presents introductory information about the nozzles for trimmers, and the decision on the need to use them to solve the relevant problems must be made independently. It is only necessary to note the fact that you should not purchase nozzles, the safety of which is in doubt. This applies to cutting discs for grass with a chain from a chainsaw, as well as devices such as angular grinder or chainsaw. During the operation of such devices, the slightest malfunctions entail serious injuries that can be incompatible with life.