DIY plywood circular saw

A circular saw

When designing a machine for use as a stationary saw, you can immediately think about the design of a circular saw. Such a machine uses a large base table as the basis of the structure. A slot is made approximately in the middle of the table. Below, under the tabletop, the mechanism of fastening and drive of the saw blade is fixedly fixed.

We can even use a sturdy wooden table. The cut for the saw blade should be 10–15 mm wide. Below, under the table top, an “angle grinder” is fixed without a protective cover (it will only interfere). The attachment of the angle grinder must provide for a firm fixation of the angle grinder, but be able to quickly disconnect the unit.

Since the saw blade with the drive is rigidly fixed in the table structure, the material is moved over the table top simply by hand. This does not provide an accurate cut, but it allows you to machine very long workpieces.

There are circular saws, in which part of the table moves with the workpiece fixed in it. But such designs are too complicated to make with your own hands. The main advantage of a classic circular saw is simplicity.

You can build such a “circular” in just a couple of hours from any material at hand. There are examples of designs in which the angle grinder is simply pulled onto a large tree stump by means of construction clamps. A working table with a slot is placed on top of the disk and is attached with self-tapping screws through to the same stump.

A not so primitive, but very compact type of circular, can be a construction of two pieces of thick plywood and a pair of bars. An angle grinder is attached to the bottom sheet with clamps. The top sheet with a slot for the material and a corner-stop for the workpiece is put on the slot over the disc. The far ends of the plywood sheets are connected by a furniture “piano” loop.

It turns out something like a house of cards. A very simple design that can literally be made from garbage in half an hour. The mechanism is not very accurate, but it makes it much easier to cut a large number of workpieces.

How to make?

To make a cut-off machine from an angle grinder with our own hands, we will need to fix the angle grinder on a bed or swing arm. The table on which the material to be processed must be large enough.

The mechanism that secures the material to the table and secures the angle grinder to the frame must be strong and accurate. This will ensure not only a smooth cut, but also safety during work.

If metal is used for the structure, it is better to make the joints welded. Bolted connections are also quite strong, but they tend to loosen and move during operation.

In any case, the wooden structure will be assembled with metal hinges, corners or screws. All connections of parts must be carefully thought out and fixed. Bolted and screwed connections must be secured with split washers or castellated nuts. It is better to glue the screws and screws that enter the tree. This will, of course, make repairs impossible, but wooden structures are usually easier to rebuild based on experience.

With a broach

A type of pendulum mechanism is broaching machines. Their design allows not only lowering and raising the cutting disc, but also longitudinally moving it along the cutting line of the cut. This mechanism allows you to process materials that are wider than the diameter of the cutting disc.

Unlike a simple pendulum, the design of the broach mechanism contains not only a hinge for attaching the pendulum arm, but also skids that allow you to move the saw unit closer and further from the hinge, moving it along the mowing line of the cut.

However, it is still not permissible to tilt the cutting unit to the left or right. It is difficult to independently make guide rails of the required stiffness. If possible, you can adapt the old mechanism from a small vertical drilling machine to move the carriage.

When making a metal machine for an angle grinder, you can try making carriage guides from a suitable metal profile (for example, an angle). The carriage itself is attached to the profile with simple ball bearings. In order for the mechanism to be accurate, on one side of the carriage, the bearings must be fixed on the platform and pressed down by powerful springs.

There is an interesting experience of using depreciation “struts” as metal guides. They are used in passenger car suspensions, tailgate lifters, and even as gas springs that hold kitchen cabinet doors that open upwards.

We do not need the filler of the “racks” and even interferes with it. All that is needed from the design is a rack with a piston and a cylinder in which they move. In the case of a gas-filled rack (furniture or from a car door), it is enough just to drill a small hole in the bottom of the cylinder and the gas will escape. From the car shock absorber strut, you will have to not only release gas, but also drain the oil.

When choosing gas springs, pay attention not only to their length, but also to their diameter. Heavy duty springs are generally more accurate and more durable. In any case, the length must be selected as long as possible in your design.

In wooden structures, some craftsmen use furniture hinges from drawer drawers as guides. These are pretty accurate mechanisms. All you have to do is select the strongest commercially available and install multiple parallel runners. This will provide even greater structural strength and allow it to last longer.

Blueprints

On the Internet, it is easy to find drawings of beds of various shapes and designs. They are unlikely to be useful unchanged. It all depends on what materials you have at your disposal, as well as what the shapes and sizes of your angle grinder are.

In any case, it is useful to pay attention to what designs were obtained from different materials from different craftsmen. Then choose the appropriate option and take it as a basis. But you shouldn’t neglect the design. Drawings, carefully drawn up at the design stage, may not describe your design in detail, but they will save you from offensive mistakes and mistakes.

Electrical part

Since the angle grinder will be fixed from below, we will no longer be able to turn it on in the usual way. We will have to provide for the installation of the following elements:

• a clamp that will constantly hold the control key in the “on” position;
• a socket for connecting an angle grinder;
• control station that turns the electricity on and off at this outlet.

It is very good to use an industrial control room in such a design. This unit has two keys. The “Start” button is rather tight, which prevents accidental switching on. The large and soft “Stop” key allows, if necessary, to quickly turn off the device, reaching it with any part of the body.

Tools and materials

The most durable and comfortable construction of the machine is made of metal. For such a design, you need to prepare:

• a metal sheet;
• metal profile (for example, corner or channel);
• pieces of metal pipes;
• steel bars.

From the tool you will need:

• the angle grinder itself;
• cutting discs for metal;
• cleaning discs;
• drill;
• drills for metal;
• welding machine.

You can do without welding. Well-planned and neatly locked bolted connections hold no less firmly. But if possible, it is preferable to use welded joints. This guarantees not only strength, but also design accuracy.

If welding and metal rolling are not at hand, examples of strong and reliable structures of a wood cutting machine are known. You will need:

• plywood sheet 8. 12 mm thick;
• hardwood bar;
• robust and massive door hinges.

But plastic is hardly useful to us. Although plastic products are easy to handle and look good, they are not very durable. The most unpleasant thing is that the plastic quickly loses its shape. And for a cutting machine, the rigidity of the structure is important. This guarantees an accurate and safe cut.

Making a cutting machine from an angle grinder with your own hands

• Tools and materials
• How to make?
• Blueprints
• A circular saw
• Pendulum
• With a broach
• Electrical part
• Safety engineering

Angle grinder (aka “angle grinder”) is a simple and versatile hand tool. But handling an angle grinder requires a steady hand and an excellent eye. A disc suddenly jammed in the material not only takes the cut line to the side, but can also collapse, which is dangerous.

On the other hand, stationary saws are large and massive. It is not easy to drag them directly to the place of work. Combining the advantages of an angle grinder and a stationary circular saw will help a compact device. an attachment that allows you to firmly fix the angle grinder and use it as a miter or even circular saw.

The material to be processed will be firmly fixed on the machine table. Our angle grinder, securely fixed on the bed, will act as a working tool. This will allow you to quickly and safely cut materials strictly along the marking lines.

Pendulum

Today, the most common design of a cutting machine is a pendulum mechanism. Machines of this kind also have a large slotted table at the base. But unlike a circular saw of a classical design, the cutting mechanism with a disc is fixed above the table, moreover, on a movable arm.

The tool arm has a swivel mount that allows it to rise and fall above the table surface. This design resembles a pendulum. Therefore, the mechanism is called that way. The trimming disc, plunging into the workpiece, falls below the plane of the working table. This allows you to make a cut in the material up to 1/3 of the disc diameter.

An angle grinder complete with disc and protective cover will be mounted on the pendulum arm. Here you have to be creative, because the body of the grinder is designed for a comfortable hand grip and has a complex shape. In addition, I would like to be able to use the angle grinder separately from the machine.

Usually, a solid and rigid bed is arranged on the pendulum, carved from wood exactly in the shape of the existing angle grinder. For ease of removal and installation, the angle grinder is fixed in the bed with clamps on the screws, tightened with wing nuts. The fastening force of the angle grinder must be sufficient and the stock material must not slip. This will ensure a firm hold of the tool and safe operation.

If you are making a pendulum machine out of metal, it is best to make homemade hinges from ball or roller bearings. The result is a very accurate, strong and durable construction.

In the manufacture of machines from plywood and wood, ordinary door or wicket canopy hinges are used as hinges. The attachment will not be as precise as the homemade hinges, but it is quite sturdy.

You should not be limited to one canopy loop. Make the hinge as wide as possible and secure with two heavy-duty hinges set towards each other at a slight angle to the axis. This connection will be accurate and durable.

Usually, for the convenience of work, the “pendulum” structure is spring-loaded. This allows the cutting tool to be held in the upper position at all times without applying force. After the material is placed on the table, the pendulum is lowered by hand. The fact that the mechanism is “suspended” by the spring allows you to precisely control the cutting force and tool feed by hand.

The simplest option is to place a compression spring under the pendulum arm. This is a very compact and rational design, but not always a master has a spring of suitable power and length at his disposal.

If the space at the workplace allows, you can make a pendulum arm in the form of a swinging rocker arm. The opposite end of the lever can then be pulled downward by the tension spring. Such a spring is much easier to pick up. It will be possible to use a rubber band or even simply hang a counterweight of a suitable mass on the far end of the rocker arm.

For the cut to be accurate, the workpiece must be secured to the table. In the simplest case, it is enough to provide back stops, against which the material is simply pressed by hand. If possible, it is better to provide for fastening a vice of a particular design.

If the fastening of the material on the table allows you to turn the workpiece at one angle or another, such a machine is often called “miter”. Usually, for simplicity of design, the workpiece is rotated at several fixed angles. for example, 45 and 60 degrees to the plane of the disc.

Main units, materials, tools

The algorithm for creating a circular saw with your own hands is quite simple. First, you need to determine for what purpose the circular will be used. If this is a small portable machine for working with laminate and plywood, then here it is worth thinking about a device from a hand-held circular saw, and if you have more ambitious tasks, then it is better to think about a more reliable engine and impressive dimensions of the machine.

In any case, you will have to make drawings of the device in order to calculate how and where the equipment will be installed, how the main parts will be attached, and at the same time think over what tool you need to work.

For a small portable circular saw from a hand saw, you can use the popular plywood or chipboard body assembly pattern. Well, if you plan to use a belt drive and a motor from a washing machine, then you will need a tool for working with metal. Welding work is indispensable here.

Circular saw device

The circular saw device, like most stationary machines, consists of the following main parts:

• Bed or base;
• Motor. most often it is an asynchronous electric motor;
• Belt drive. pulleys and transfer belt;
• Circular saw working shaft;
• Desktop;
• Security devices;
• Electrical equipment.

The entire layout of the device is based on a massive bed or base. It can be a one-piece piece cast from cast iron aluminum, or have the form of a frame. a body assembled from scraps of pipes or corners. A home-made machine, it is preferable to make from cuttings of profile pipes, for example, you can use square profile pipes 25×25 mm or a rectangular profile 20×40 or 25×50.

The spindle for mounting the circular saw blade is used as a thread on the shaft. In this case, the saw is clamped with a nut. The spindle assembly can be made in a different way, as with a hand-held circular saw. drill a hole in the shaft, cut the internal thread and clamp the disc with a bolt. But as practice shows, the first option is better. the circular saw is clamped more reliably, and the thickness of the blade can be selected differently.

When using a belt drive, the electric motor and the working shaft are connected by a V-belt. The rotary motion from the motor shaft is transmitted through the pulley to the working shaft pulley. It is recommended to design a circular sawing machine according to this scheme, this will increase the resource of the motor and eliminate the possibility of jamming. If the circular disc gets stuck and it stops and the belt just stretches and the engine continues to run.

The working table is necessary so that the workpiece is in the same plane during operation. The circular table is made as wide as possible, so that you can safely rest the part on its plane.

In order for the woodworking circular saw to be safe, devices must be installed to ensure the safety of work. This can be a protective cover, a pusher for working with small parts, a parallel stop.

One of the options to assemble a simple budget machine for homework is the option of converting a manual circular into a stationary one, adding a bed and a wide working surface to the actually finished device.

Stanina

It was no coincidence that the frame was made of a shaped tube. The design uses a profile of 20×20 mm and 25×25 mm.

This frame is strong and stable. The side racks are made the same. They are connected at the bottom with a 25×25 profile, and at the top there is a jumper made of a pipe with a section of 20×20 mm. The resulting frame of the table circular is raised above the surface on plastic legs, this increased the stability of the instrument. Bolts for fastening the engine are installed on the lower jumpers.

The working shaft attachment is made of a nut. The inner thread of the nut is ground down, the diameter corresponds to the outer diameter of the shaft bearings. To fix the bearings, a retaining ring will be used, under which a groove is made.

Table top

A sheet of metal with a thickness of 2 mm will be used as the tabletop of the working table in the circular. This is enough for the workpiece to move freely on the work table.

Holes are made in the metal for the countersunk head screws. In addition to metal, chipboard can also be used as a table, and made from plywood. It is recommended to make the working table of the circular so that it is possible to install an emphasis on it.

Making a circular saw with your own hands

The need to have a small circular machine on hand has probably occurred to everyone who at least once tried to make a straight cut with a jigsaw or a hand saw of a small plank or strip of laminate. It’s another matter when such an operation is performed on a stable machine. Even if this circular was assembled from metal with its own hands and does not look very presentable, this wood machine allows you to do the job faster and better. That’s just how to assemble the circular yourself at the lowest cost and use the available parts, for example, the engine from the washing machine?

Motor

The engine already has a pulley. This is a standard pulley used in a washing machine.

Elongated engine casing studs will be used as attachment points. The standard studs were replaced with longer ones with M8 threads. Brackets are made of 60×60 mm angle. Holes were drilled at the point of attachment to the engine, and a slot was made at the points of attachment to the bed to adjust the belt tension.

Do-it-yourself miniature machine from an engine from a washing machine

But as for the engine from the washing machine, this is perhaps one of the best motor options for assembling a circular saw at home. Washing machine motors have a long service life and endurance. Low shaft revolutions are fully compensated by the design. in most washing machine engines there is a groove for the pulley key, and the body itself has convenient mounting holes. You can increase the number of revolutions of the saw blade by installing pulleys of different sizes on the motor and the working shaft, or take an electric motor from the centrifuge of the same washing machine. By the way, a machine with a direct drive can be made from a centrifuge motor, such a motor usually has a long shaft, and a small-diameter saw can be installed directly on it. \

But the main advantage of the engine from the washing machine is its power. It is designed for a long period of work, and for a circular saw this is the most important thing.

SAMODELKIN’S FRIEND

Stationary plywood circular saw

Dear visitors of the site “Samodelkin friend” today we will consider one of the options for creating a table for a stationary circular saw made of a circular cut-off saw with our own hands. Step-by-step photos of the assembly of the machine are attached. It is quite possible to make a stationary circular saw with your own hands and at the same time with minimal costs for raw materials and components. The most expensive thing in the design will be the presence of a circular saw, but if you have one, then this is great) The tabletop can be made of two sheets of plywood glued together with carpentry glue, it is advisable to use moisture-resistant “Finnish plywood“, it is very durable and will last longer term unlike usual.

Next, you need to make a bed for a tabletop with a circular saw installed on it, and for this purpose, used bars or boards from which you get an excellent base for the machine are perfect. Also self-tapping screws for wood, for assembling the structure into a single whole.

It will become much more convenient to work in your workshop or garage with a stationary circular machine, as well as it is much more pleasant realizing that a lot of money has been saved, because the for factory machines you yourself know what.

And so, let’s take a closer look at the step-by-step process of assembling a homemade circular.

Materials (edit)

• Circular Saw
• Finnish plywood 2 sheets 1200 x 800 x 12 mm
• timber or board
• wood screws
• metal plate 1 mm

Tools

• jigsaw
• drill or screwdriver
• measuring tool
• milling cutter
• screwdriver
• wood glue and brush

Step-by-step instructions for assembling a stationary circular saw with your own hands. Initially, the base was assembled from the planks, it is advisable to take a beam so that the structure is reliable. In the future tabletop, the tabletop is first marked and a seat is cut out for the circular saw plate. A milling cutter selects a seat for the installation. Two sheets of “Finnish plywood” are glued together with wood glue. A plate with a cut under the saw blade (preferably metal) should be installed on the front part of the technological opening.In addition, you can watch the video.

Desktop drilling machine from scrap materials

Wine fermentation trap. the best designs from scrap materials

Circular saw from washing machine engine

If there is an old washing machine in the household that has exhausted its working life, you can use its parts. Washer motor can give life to a new tool.

If there is a choice, then the engine should be taken with a high power level. If there is no choice, then the engine that is available is taken as a basis.

Initially, you need to prepare the motor for the future circular. Using an ohmmeter, the coil with the highest resistance is determined. Are subject to verification:

• connections at the outlets of the brush and collector;
• speed sensor wires.

Next, you need to connect each of the two outputs of the collector with two contacts of the coil. After connection, a test run is made, the device is connected to the mains.

If you swap the contacts, rotational movements will be performed in the opposite direction.

You can increase the functionality of a homemade circular saw by equipping it with a device that reduces or increases the speed of rotation of the blade.

To do this, you can take as a basis a trigger from a handheld electrical device or a dimmer. They are connected in the following sequence:

• one of the coil contacts is connected to the armature contact;
• the second contact is connected to the mains supply;
• the remaining armature output through the dimmer is output in the same way to the mains supply.

After the motor is fully prepared, you can proceed to the further construction of the circular machine.

[stextbox As a frame, it is better to take a welded metal frame, at the bottom of which the motor is fixed. The next step is to make a motion module. [/ Stextbox]

The cutting tool (disc with teeth) is rotated through a drive belt that is fixed to a pressed-in smaller pulley. It is important to make notches on the pulley that will prevent the V-ribbed belt from sliding.

To prevent slipping of the drive loop, a small protrusion is specially welded on the edge of the larger pulley. Before starting the circular, it is important to check the reliability of the disk and the engine itself. If the disc falls off during operation, it can cause serious injury, even in some cases even fatal.

Homemade grain crusher from scrap materials

Purpose of the circular saw

Home craftsmen strive to fill their workshops with a variety of useful devices and equipment. With a circular saw available, it will be easy to do woodwork without spending a lot of time and without much physical effort. For instance:

• cut the board;
• process the workpiece, strictly maintaining the dimensions indicated in the drawing;
• cut firewood.

The design of the tool is easy to manufacture, which attracts the attention of craftsmen who want to create useful devices with their own hands.

A circular saw consists of the following elements:

• bed;
• countertops;
• cutting tool;
• motor, which ensures the rotation of the shaft, and then the rotation of the cutting tool.

[The stextbox of the circular operation is that after starting the electric motor, its shaft begins to rotate, driving the cutting tool. A blade with sharp teeth acts as a cutting tool. [/ Stextbox]

The disc is fixed so that its middle is below the level of the table top. As a result, only a separate segment of the disk is displayed above the surface.

The workpiece is brought exactly to the rotating disc, the teeth of which cut into the tree, creating a perfectly clean cut strictly according to the drawing.

The circular can be supplemented with the following elements:

• a pusher advancing the wood blank in the direction of the rotating disc;
• lifting mechanisms providing cutting depth.

Using ready-made drawings and diagrams, home craftsmen can assemble a tool based on:

• Angle Grinder;
• washing machine motor;
• chainsaws;
• drill.

Reliable PVC boat anchor from scrap materials

Circular saw from a conventional drill

Initially, a semblance of a table is built. Four legs are attached to the tabletop. A slot is marked on the surface of the tabletop, from which the cutting disc will protrude.

On the reverse side of the tabletop, at a short distance from the slot for the disk, a rectangular bar with a round hole cut out inside is fixed. Its diameter should be the same as the chuck of the drill used. Using a jigsaw, the intended slot is cut.

[stextbox cut a slot on another plywood sheet, and parallel to this slot, cut another slot, the width of which should be equal to the width of the prepared wooden block. The second plywood sheet is placed on top of the first so that the disc slots coincide. [/ Stextbox]

A wooden block is laid in the second slot, a rectangular sheet of plywood is glued to it at right angles, which looks like a side. It is he who will act as a guide. All wooden elements are glued and must be fixed with bolts.

The drill is securely fixed on the underside of the tabletop, not forgetting that its cartridge must fit into the rounded element previously installed on the back of the tabletop.

You can additionally watch a video that demonstrates the process of building a circular at home. Each master will be able to create a useful tool for working with wood with his own hands. But remember to follow all safety rules to avoid unnecessary injury when working with the circular saw.

Saw Based Angle Grinder

DIYers strive to have an angle grinder available. This tool takes its rightful place in the workshop. an angle grinder allows you to:

• cut metal;
• clean weld seams.

Sometimes craftsmen buy a new angle grinder while the old tool is still in working order. To prevent it from gathering dust on the shelves in the workshop, it can be taken as a basis for the manufacture of parquet, and by adding a table to the bed, it is possible to build a stationary circular saw.

Before starting work, you need to prepare materials and tools. During work, you will need plywood sheets, wooden blocks, wires, external switches. It will be easier to perform the actions if the master will be able to use a drill, hammer, jigsaw, pliers.

The angle grinder itself will be needed when cutting materials for making a circular saw. When all materials and tools are prepared, you can proceed to practical work:

• Four rectangular sheets with sides of 40 and 80 cm are cut out of plywood.
• All four sheets are connected to get a box with a base 80×80 cm.
• To facilitate the joining process, four small blocks are fixed in the corners (they will not only facilitate assembly, but also give additional strength and reliability of the structure).
• The hollow box is covered with a table top (the easiest option can be cut from plywood, but professionals recommend using a material with a laminated surface).
• A narrow space is cut out in the prepared tabletop through which the cutting tool will exit.
• Holes are drilled on both sides of the cut to ensure a secure fixation of the tool.
• the angle grinder is placed under the tabletop, securely fixing it with fixing materials (the angle grinder must be fixed so that it does not change its position during operation).
• Any power tool has a power button, it must be locked, since in the future the circular will be turned on through an external switch.

Following this step-by-step instruction, you can assemble a working model of the saw, as in the photo.

[stextbox also build a movable carriage into which a nail is driven in, and then using pliers, bite off its head. As a result, an important structural element is obtained. an eccentric, on which the workpiece is put on. With its help, when rotating the part, it is possible to accurately cut corners, turning rectangular workpieces into rounded parts. [/ Stextbox]

In a similar way, a circular is constructed on the basis of a circular saw. At the same time, the process is greatly simplified in many ways, since the tool will be much easier to attach to the tabletop.

DIY circular saw table

A circular saw is used to cut wood along the solid wood. Its cutting base is a disc-shaped plane with a serrated outer edge. Such saws are not only hand-held, but fixed on the table. How to make a universal circular table so that this cutting tool can be installed on it? Below are several ways to make a do-it-yourself circular saw table.

The second version of the circular table. Photo of manufacturing technology

A do-it-yourself saw-table is made of boards, as the most affordable material, quite often. To make this table you will need:

• plywood sheet (thickness 20 mm and more);
• boards 50 by 100 mm;
• bars 50 by 50 mm;
• several self-tapping screws;
• wood glue;
• one type of wood varnish.

• a sheet of laminated plywood with a thickness of 9–11 mm (800×800 mm);
• 4 sheets of laminated chipboard 16 mm thick (400×784 mm);
• several bars 40×40 mm;
• several bolts and screws;
• aluminum cornice.

Any hand-held circular saw with a large blade can be mounted on such a table. Drawings of a table for this type of circular can be easily found on the Internet.

Such a saw is made in several stages:

• A drawer of the future table is made from laminated chipboard sheets. It does not have a bottom, and the walls are fastened with bars, which, in turn, must be fixed with bolts and screws.
• A cover is made of plywood with a hole into which you will need to insert a saw. The marking for the hole is carried out along the support shoe and the lower protective casing of the circular saw. The hole is cut with a jigsaw.
• The saw is fastened to the plywood with ploughshare bolts with a countersunk cone head. The plywood cover is fastened to the chipboard body with a steel case 18 mm.
• Wiring is laid along the side of the tabletop and a start button is installed.

Circular saw guides are made of timber or aluminum curtain rod.

Examples of finished tables for circular saws

It is not always advisable to make a table for a circular with your own hands. It can be too bulky and awkward, and it is difficult to adapt it for high-precision cutting of wood. Therefore, if you are not sorry to spend a certain amount of financial resources, it is better to purchase factory-made tables. They are made of durable and easy-to-use materials, are safe when switched on, and also have a factory warranty in the event of a breakdown.

The Jet JBTS-10 circular saw has a retractable table on each side, increasing the area suitable for work. Thanks to the belt wire, the sawing is quiet, and the service life of the electric motor is also increased. The presence of an eccentric clamp eliminates the displacement of the machine during operation, which makes it convenient to use in any conditions.

When using the table saw Caliber EPN-1100, it is possible to saw wood materials in the longitudinal and transverse directions, as well as at different angles. In this case, the level of inclination of the saw can be selected and fixed.

In the sawing machine Enkor Corvette-10M 90101, side and parallel stops are used, which greatly facilitates the work. The saw blade can be tilted up to forty-five degrees when cutting. An industrial vacuum cleaner can be connected to the machine to remove wood dust. At the same time, the device is characterized by lightness and small dimensions.

Using the stationary circular saw Einhell TC (TH).TS 820 allows you to work with sawn timber in a mass production environment. It is a suitable tool for processing not only wood, but also fiberboard blanks. The design of this model provides a hole into which devices that produce wet and dry cleaning of the machine are connected. At the same time, the equipment is so compact that it can be installed on any workbench.