DIY trencher for tiller

Do-it-yourself snowplow bucket

the tiller will come in handy on the farm not only in summer, but also in winter. It is often equipped like a snow blower. It is enough to make a bucket for the tiller, and the iron assistant will do the hard work.

A snow shovel is usually made from a 200 liter iron barrel. You will also need metal strips, a square pipe, rubber and steel plates and fasteners. bolts, nuts. From tools. pliers or pliers, drill and drill bits for metal, wrenches, grinder, welding machine.

an angle grinder at the barrel, the side parts are cut out. Then the workpiece is cut into three pieces. Two of them are welded along the contour. The remaining third of the barrel needs to be divided into metal strips, which will be the bucket knives. Three 6mm diameter holes are drilled into them for attachment to the edge of the bucket. Instead of a barrel, you can use a metal sheet, which will need to be bent by heating.

A strip of metal is welded to the bottom of the bucket to make it heavier. The metal strip is completely covered with rubber to prevent wear. The bucket is then attached to the tiller. To protect against corrosion, a homemade bucket is primed and painted.

You can turn a wheeled tiller into a snowmobile using a trailer and winter wheels. With the help of a channel, the trailer is fixed to the frame. Used truck cameras are used instead of expensive wheels. On each wheel, the deflated chamber is secured with chains and inflated again. Equipping a snowmobile machine is quite simple and homemade sleds.

How to design a trencher?

A homemade trencher is a hinged attachment to the tiller, which allows you to quickly and effortlessly dig trenches and holes. It is a kind of compact excavator that is both maneuverable and economical. Moves on a wheeled or tracked chassis.

The digger attachment allows you to dig trenches and holes even in frozen ground. The walls of the trenches are flat, without shedding. The excavated soil is light and crumbly and can be used for backfilling.

Two cutters are fixed on the front suspension, on the rear. a shovel for extracting soil from the trench. It is imperative to attach safety guards to the cutting discs and the chain drive. By the same principle, a drill bit is made from a metal rod and plates.

How to make a flat cutter with your own hands?

A practical addition to the tiller is the flat cutter. This is an irreplaceable assistant who creates beds, weeds and spuds plantings, levels, falls asleep, loosens the ground. The possibilities of such a nozzle are almost endless.

If you place the blades of the plane cutter on the left and lead in the same plane with the soil, then you can weed or loosen the ground. Raising the appliance slightly, the blades turned to the left will mow tall weeds. If the blades look down, then it is easy to create beds with them.

A flat cutter will again help to form grooves for planting and fill in the seeds. This is the function of the burier.

You can use the Fokin plane cutter as a hitch for a tiller. He has the necessary holes for hanging on the structure. If a flat cutter of a different size is required, then you can make it yourself. Drawings and a small metal workpiece will help with this.

The metal must be of sufficient thickness and strength so that in the future it can function as a blade. The sheet is heated with a blowtorch and bent according to the pattern. When the plane cutter is in shape, it is cooled with water. In order for this workpiece to become an attachment, it is necessary to make holes for fasteners and sharpen the workpiece with an angle grinder.

A sheet of metal can be replaced with a piece of pipe, to which pieces of metal are attached like blades. They need to be sharpened.

How to make attachments for a tiller with your own hands?

• How to make a flat cutter with your own hands?
• Sizes and features of the manufacture of hedgehogs
• Do-it-yourself snowplow bucket
• How to design a trencher?
• Manufacturing of other suspended structures

In order to increase the capabilities of the tiller, it is enough to equip it with various attachments. For all models, manufacturers have developed numerous add-ons, the use of which makes it easier to work on the ground.

On sale you can find plows and seeders, hillers, furrow diggers, sledges. The choice, of course, is large, but many cannot afford the cost of such equipment. But it is quite possible to make it on your own from cheaper or used materials.

Sizes and features of the manufacture of hedgehogs

a tiller with a potato growing attachment will save time and effort when caring for this crop. Weeding hedgehogs are a functional attachment that allows you to quickly and efficiently defeat weeds. In the process of weeding, the plants are not simply cut, but uprooted. The land around the plant is well loosened and huddled. Thanks to this, the plant is not only freed from weeds, but also receives sufficient water and oxygen.

Based on diagrams and drawings, you can make them yourself.

Components for hedgehogs:

• 3 discs made of metal or a ring;
• a small piece of pipe with a diameter of 30 mm;
• steel dowel rods.

It is preferable to use rings instead of discs, which will lighten the whole structure. The sizes of rings for making tiller’s hedgehogs are different. The most common are 240x170x100 mm or 300x200x100 mm. The rings are attached to the pipe through jumpers. The connection must be made at an angle of 45 degrees with a distance between the elements no more than 15-18 cm.

The spikes, cut from a steel rod 10-15 cm long, are welded onto the rings and the axle itself. Depending on the size, they are attached to a large ring in the amount of 15 pieces, to a small one. 5. Also, several pieces can be welded onto the axis.

To facilitate the work with the structure, the hedgehog tiller is equipped with additional wheels.

Manufacturing of other suspended structures

So, to cultivate the land, a plow is needed that can overcome virgin soil overgrown with grass, wet or stale soil. To make it, you need a steel plate about 5 mm thick. Using the rollers, the plate is bent into a cylinder. Edges sharpen angle grinder.

The resulting home-made plow is hung on the tiller’s stand through the hitch.

By the same principle, it is easy to make a furrow-forming attachment. It is good if there are racks from the cultivator. They can be attached to a corner or made two racks from scrap materials. For this, plates are cut from a metal sheet with a thickness of 1.5-2 mm. The size of the plates should correspond to the depth and width of the furrow. They are fastened with bolts to the struts of the structure. You can use such a nozzle for instillation. One has only to give the plates the required shape. They should be in the form of a disc or circle, located at a certain angle. From above, such plates are located closer than below. Due to this, the discs, while rotating, open the cavities outward.

The cranberry tiller attachment contains a self-propelled crawler platform. The intake is fixed on the swing frame of the platform. It is made in the form of a box with bent parallel teeth. Moving, the device with the help of the fan pulls the berries into the box. The fan is powered by the engine. Screw-shaped spirals are installed in the box.

Plucked cranberries are heavier than garbage, so they fall to the bottom of the container. Leaves, small specks that fall along with the cranberries, along with the air flow from the fan, are removed through the hole.

The tiller brush is used to clean the area not only from leaves, but also from shallow snow. Simplicity, efficiency and versatility of use are the obvious advantages of this hinged element. A brush shaft is vertically attached to the tiller. A ring and discs with brushes are alternately put on it. The diameter of the rings is 350 mm. The width of the grip of such a brush is usually made no more than one meter. This allows the tiller to remain manoeuvrable and cover a fairly large surface area for cleaning.

The length of the bristles is 40-50 cm, otherwise it will soon begin to wrinkle and wrinkle. It will not be possible to restore the properties of the bristles, just attach new discs. The speed of the tiller with the attached brush fluctuates in the range of 2-5 km / h, depending on the engine power of the unit.

To learn how to make a plow to a tiller with your own hands, see the next video.

Trencher Information

Although it is possible to dig trenches by hand, it is still more profitable to use specialized equipment.

There are several reasons for this:

• In the process, the trench turns out to be narrow, deep and with steep edges. With this method of digging, the risk of splashing the walls is reduced.
• The quality and efficiency of the unit are not affected if the ground is denser than usual.
• When this mechanism works, the need to remove the excavated soil is significantly reduced.
• Compared to an excavator, it should be noted that the excavated soil can be used at any time to fill the hole. In this case, the excavator can dig out blocks that must be broken before use.
• This mechanism has high performance.
• The trencher works effectively in winter conditions when digging trenches in frozen ground.

Tiller Trencher

Description

A trencher for a tiller is an equipment that can make life many times easier for its owner, who is planning to lay communications, perform gardening and other work, where digging long and narrow trenches is indispensable.

Tiller mounted trencher

Of course, there are special motorized units. industrial-level trenchers, the digging depth of which can reach 1 meter 20 centimeters. Smooth, strong cut cuts hold their shape perfectly and do not crumble. This is an excellent equipment, its only drawback is the high cost, available only to specialized organizations.

What should the owners of private houses and land plots do when a shovel is not able to help, but there is a tiller on the farm? And then a real way to solve the problem appears. a nozzle for a tiller for digging trenches. Digging trenches with a tiller will take much less time and effort, which will have a beneficial effect on labor productivity.

Trenching Attachment Tools

The working bodies of the universal attachment are:

• steel frame;
• cutting chain (bar);
• drive (mechanical, pneumatic, etc.);
• chain tensioner;
• moldboard auger;
• protection (clutch).

Depending on the type of working body, there are the following types of diggers:

• scraper type;
• plow;
• bucket;
• incisal type;
• with a toothed wheel;
• mixed.

For an hour of operation, such a hinged device is capable of digging from 60 m to 180 m in length, depending on the engine power.

Trencher in action

The operation of the unit is simple: after starting the cutting mills, trenching begins. Then the drive of the undercarriage is started, which makes the device move, and the auger or moldboard shovel moves the excavated soil on the surface away from the felling.

Of course, a self-made device for digging a trench with a tiller makes work easier, saves time, effort, money, and turns ditch digging into an everyday procedure.

Applications

This device can be used for various purposes:

• With its help it is possible to dig ditches. The most powerful trenchers can reach a depth of 200 cm.The more affordable species, depending on the type, are capable of digging a ditch from 30 to 90 cm deep.
• Sometimes, to transplant a tree, you need to carefully dig out its roots along with a lump of earth. This can be done with a trencher.
• When the construction of a house is to begin soon, the site for work must be prepared in advance. The tool in question can help in this work.
• The trencher can be effectively used to remove roadbed before road repairs.
• It can actually be used as a motor-cultivator: carry out reclamation work, do drainage and loosening.
• This device can help when performing foundation laying work.

Trencher speeds up work when laying foundations

Purpose and principle of operation

tiller with a trencher is able to perform the following works:

• dig a trench under the foundation;
• dig a drainage ditch;
• help in planting trees and laying curbs;
• design work;
• removal of asphalt pavement;
• digging drainage channels, etc.

Tiller mounted trencher to tackle any type of soil, while keeping the cut neat and not crumbled into the resulting cavity.

The bar cuts through the soil and, as it deepens into the soil, descends to its optimal depth (for walk-behind tractors, it is 25-90 cm, while specialized equipment will cut the soil to a depth of 1200 cm). The soil is captured by the cutting edges (shovels) and fed to the moldboard auger, which takes it to a distance of 15 cm. From the trench.

The lineup

It is worth highlighting two categories of technology:

• self-propelled;
• non-self-propelled type.

Specialized equipment is represented by brands:

• Laski TR50;
• JSC “Mikhnevsky RMZ”;
• Kwik-TrenchEarthSaw;
• GroundHog T4;
• TKMG-1200;
• Sable / BS / 50 /;
• Vermeer RT60;
• Barreto 912HM;
• GroundHog T-4 Trencher.

Motoblock trenchers are represented by the TrenckIt model, which is produced by the manufacturer QuickAttah. This equipment is connected to both gasoline and diesel tillers, the engine power of which ranges from 8 to 15 horsepower. For the convenience of work, a tracked or wheel drive technique can be used.

GroundHog T-4 Trencher

Tiller Trenchers: Why You Need Them?

The equipment is used in the process:

• digging trenches;
• planting trees;
• removal of unsuitable road surface;
• cutting out blocks of soil;
• loosening the soil;
• preparation of the territory for planting works.

Modern manufacturers have made sure that every tiller owner is able to enjoy the operation of the device, so they have created different versions of trenchers: which are one with the device and those that are perceived as attachments.

• The first type is often used in their professional activities by representatives of public utilities, builders and landscape designers. Models such as Barreto 912HM, Laski TR50, Sable / BS / 50 / and Ground Hog T4 are the most popular because they allow you to achieve your goal as quickly as possible with minimal effort.
• The second type is attachments created in factories specifically for certain brands of tillers. Almost every manufacturer accompanies a new product with the specified accessory.

What does that require?

• Welding;
• Angle Grinder;
• Two road mills ETs-1800;
• Moldboard shovel;
• Protective covers;
• Skillful hands and enthusiasm.

To work on a homemade trencher, you need to take the indicated road milling cutters, because their constructive solution fits perfectly well.

Tiller trencher. do it yourself

Trenchers have made life much easier for garden owners and land workers. Now you do not need to waste time and effort to dig trenches with a shovel, special devices will take care of all this.

Is it possible to create a trencher for a tiller with your own hands?

The answer is in the affirmative, because not all owners of a tiller can afford the purchase of specialized objects, and on a farm without a trencher it is very difficult. Therefore, they find a way out of the situation and create their own versions of very productive adaptations of the specified plan.

The creation process itself is very straightforward:

• A bar with two cutters should be attached to the front suspension;
• On the back, it is necessary to place a moldboard shovel to clear the ditch from the ground;
• The chain drive and cutting blades must be equipped with protective guards.

After seeing the result, a person will probably ask: “How can a tiller dig a trench using the equipment received?” The principle of operation is as follows: after turning on the cutter disks, they cut the trench. Then the drive of the tiller undercarriage is switched on. The unit starts to move, and the moldboard shovel throws the soil crushed by the cutters up.

In the process of digging, the operator applies a minimum of effort, and this despite the fact that such a device can go deep into the ground by 35 cm, which is much more productive than the classic manual labor with a heavy shovel.

Tiller Trencher. Technical Parameters and Applications

Trenchers are one of the varieties of excavator mechanisms used for arranging trench depressions when laying underground highways for placing pipes for various purposes, cable power grids, communication communications.

Can be used by owners of land plots, utilities in works on land reclamation, drainage, arrangement of foundations.

Trenchers for mini equipment. Classification and device

There are several types of trenchers that are attached to the tiller.

DIY trencher from tiller

The owner of a small land plot in the course of construction work, the development of the local area has to solve the problems of laying water supply, sewer, cable networks. The trencher will significantly reduce the time for carrying out such work, save you from manual labor with a pick and shovel, but:

• It is not always possible to rent heavy construction equipment. a private construction site is generally limited in size, part of the work has already been completed, which limits the maneuvers of the tractor and excavator.
• The mini grooves offered on the market are too expensive and not very functional, any owner will hardly consider purchasing them for their own needs an effective investment of money.

With experience in working with metal, welding and cutting equipment, you can build a homemade trencher based on a tiller in a home workshop.

Technical and operational parameters of the project

Parameter indicator	unit of measurement	The quantity
General diagram of the product	mounted on a uniaxial tiller 8-13 liters. from. with power take-off
Power point	Hydraulic type. pump NSh-10 on the tiller shaft, cutter motor GMSh-32
Cutting discs	Road milling machines
Digging depth	m	up to 0.35
Trench width	m	0.10. 0.15
Performance	m / h	up to 25
Weight limit	Kg	80

The structural diagram of the device is based on the solutions adopted by the manufacturers of the ETs-1800 road milling machine.

Cold milling machine EC 1800

Hinged executive body: 1. cutting disc; 2, 3, 7. chain transmission: 4. hydraulic motor; 5. the shaft of the hinged device; 6. bar discs.

tiller and moldboard shovel

Features of the machine

• Available with 0.91 m or 1.21 m boom.
• Chain cutting elements are selected based on soil parameters.
• Hydraulically controlled sideshift and removable excavation shaft allow work close to foundations.
• The depth of the excavation is adjusted by moving the skid.
• The chain drive is equipped with an automatic tensioning device.

Technical specifications

Options	Unit rev.	Indicator value
The weight	Kg	272
Height	m	0.63
Width	m	1.54
Length	2.1
Trench depth at 60 ° slope	m	0.96
Operating pressure	kg / cm2	140-210
Hydraulic fluid flow	l / min	67.5-90
Shaft rotation speed (rpm)	rpm	125-225
Standard boom	m	0.91
Standard cutting element	a cup

tillers, structurally combined with a trencher

Such devices are most widespread. In addition to the formation of trenches up to half a meter deep, the unit will help the owner:

• in tree planting;
• loosening the soil;
• cutting out blocks of soil;
• removing the old roadway.

Trencher Barreto 912HM

Specifications

Attached units

Used for completing the executive equipment of mini tractors. For heavy tillers, Quick Attach offers the Trench It ™ mini trencher.

The device is designed to work with mechanisms of the brands Yanmar, Bobcat, Case, Daewoo, John Deere. Special couplings allow you to organize work with any tiller. Power drive from a hydraulic pump on the tiller PTO.

Tiller mounted trencher

Trencher work

The executive body. a bar with two soil cutters is installed on the front suspension of the tiller. The depth of the recess is adjusted with a ratchet mechanism for fixing the angle of the bar.

The unit is combined with the tiller front linkage device. Excavation of destroyed soil is carried out with a moldboard shovel on the standard rear suspension of the tiller.

• The power plant of the tiller and the hydraulic system of the attachment are started.
• The transmission of torque to the travel wheels is disabled.
• The cutter gyro motor starts up, the cutting discs begin to rotate and the formation of a cut of the trench.
• The chassis drive turns on and the tiller starts moving.
• The dump shovel feeds destroyed soil to the edge of the trench.

Cutting discs, chain drive must be protected by protective covers.

Trenching Attachment Tools

The working bodies of the universal attachment are:

• steel frame;
• cutting chain (bar);
• drive (mechanical, pneumatic, etc.);
• chain tensioner;
• moldboard auger;
• protection (clutch).

Depending on the type of working body, there are the following types of diggers:

• scraper type;
• plow;
• bucket;
• incisal type;
• with a toothed wheel;
• mixed.

For an hour of operation, such a hinged device is capable of digging from 60 m to 180 m in length, depending on the engine power.

Description

A trencher for a tiller is an equipment that can make life many times easier for its owner, who is planning to lay communications, perform gardening and other work, where digging long and narrow trenches is indispensable.

Of course, there are special motorized units. industrial-level trenchers, the digging depth of which can reach 1 meter 20 centimeters. Smooth, strong cut cuts hold their shape perfectly and do not crumble. This is an excellent equipment, its only drawback is the high cost, available only to specialized organizations.

What should the owners of private houses and land plots do when a shovel is not able to help, but there is a tiller on the farm? And then a real way to solve the problem appears. a nozzle for a tiller for digging trenches. Digging trenches with a tiller will take much less time and effort, which will have a beneficial effect on labor productivity.

Tiller Trencher

The lineup

It is worth highlighting two categories of technology:

• self-propelled;
• non-self-propelled type.

Specialized equipment is represented by brands:

• Laski TR50;
• JSC “Mikhnevsky RMZ”;
• Kwik-TrenchEarthSaw;
• GroundHog T4;
• TKMG-1200;
• Sable / BS / 50 /;
• Vermeer RT60;
• Barreto 912HM;
• GroundHog T-4 Trencher.

Motoblock trenchers are represented by the TrenckIt model, which is produced by the manufacturer QuickAttah. This equipment is connected to both gasoline and diesel tillers, the engine power of which ranges from 8 to 15 horsepower. For the convenience of work, a tracked or wheel drive technique can be used.

Purpose and principle of operation

tiller with a trencher is able to perform the following works:

• dig a trench under the foundation;
• dig a drainage ditch;
• help in planting trees and laying curbs;
• design work;
• removal of asphalt pavement;
• digging drainage channels, etc.

Tiller mounted trencher to tackle any type of soil, while keeping the cut neat and not crumbled into the resulting cavity.

The bar cuts through the soil and, as it deepens into the soil, descends to its optimal depth (for walk-behind tractors, it is 25-90 cm, while specialized equipment will cut the soil to a depth of 1200 cm). The soil is captured by the cutting edges (shovels) and fed to the moldboard auger, which takes it to a distance of 15 cm. From the trench.

DIY trencher for tiller

It is much faster and easier to dig a trench with a tiller, but many are stopped not only by the high price of the soil cutter, but also by the infrequent use of this nozzle (unit) on the farm. Therefore, the owners of summer cottages often prefer a homemade trencher for a tiller to a factory.

A homemade tiller trench can be made from scrap materials using a welding machine, an angle grinder and imagination. Craftsmen post detailed descriptions and schemes of homemade soil cutters on the Internet, we offer one of the schemes:

The sequence of the process of creating this attachment is as follows:

• production of a suspension on which an earth-moving boom with a bar chain will be fixed;
• the rear suspension should be equipped with a special shovel, which will allow grabbing the earth from the bottom of the ditch and lifting it out;
• do not forget about the protection, which should cover both the chain itself and the cutting elements;
• when the attachment is ready. it is necessary to design a special hitch, with the help of which the homemade soil cutter will be aggregated with the tiller.

Ivan, 36 years old:

I would like to say a few words in favor of the trencher. Three years ago I bought a dacha, decided to build it, left the old house as a barn, started building new housing for my family. The construction would have dragged on for a long time if it had not been for the advice of kind people. Basically, all the digging work was carried out by machines (I hired the appropriate equipment), including trenches for the foundation (a tractor arrived with a soil cutter and did everything in a couple of hours). Later, when the box was ready and it was the turn to pull communications, I remembered about the grouser and found compact analogs for tillers on the Internet. I decided not to waste money in vain, but to make a tool of labor with my own hands. The trencher justified the effort, later I began to use it in the garden. Now the construction is finished and my family lives in a cozy cottage, a garden, a small vegetable garden. everything is like people have.

Sergey, 54 years old:

I also had construction on the site, so I really needed a trencher. I could not find a suitable one for my Oka, so I decided to make a hitch myself. The experiment was a success, but the depth of cutting the soil is too small. 25 cm. Electricity stretched throughout the entire site, then decided to use a soil cutter in an aesthetic direction. cut trenches for curbs, built a small grotto in the garden. also not without the participation of a soil cutter.

Alexey, 31 years old:

Hello! My father has a tiller Neva, I want to use it to the maximum, there is a construction project ahead, I would like to facilitate the work by adapting the tiller. Advise which manufacturer to choose, which particular model? I even agree to do it myself, I can do it myself, but there is no specifics on the Internet, I would have a step-by-step instruction on how to make a grouser. Thank you in advance!

Choosing the right model

It is difficult for the user to find the right brand among the variety of trenchers. The performance of the unit depends on the power of the tiller, weight, depth and width of trench digging with attachments. These same factors dictate the price.

Two types of trenchers are practiced:

• Trenchers, which are designed as a single, one-piece mechanism with the unit. In practice, the most common brands are: Laski TR 50 / TR 60, TKG-1200, Barreto 912 HM. This technique is very expensive and designed for professional use.
• Mounted ditchers. Produced by factories for certain types of power units. Finding a tiller for a tiller is not easy.

In the countries of the former Soviet Union, Trench It attachments developed by Quick Attach are practiced, which are assembled with specially designed couplings, with John Deere, Case, Yanmar, Daewoo, Yanmar units.

How to make a trencher for a tiller yourself?

Attachments offered by manufacturers are expensive and can only be combined with certain tillers. For this reason, many “Kulibins” decide to make a hinged homemade trencher with their own hands.

The design is based on a homemade bar for a tiller. There is nothing superfluous. Every detail of the mechanism plays a role to facilitate the work of the operator. For these purposes, road milling cutters, homemade teeth, a factory chain, a dump shovel or auger, protective covers are used.

Trenchers can be equipped with tillers from Neva, MTZ, Kaska, Agro firms with a capacity of at least 8 liters. from.

The tiller attachment for digging trenches is installed as follows:

• A self-made bar for a tiller with cutting mills is mounted on the front suspension.
• A homemade auger or moldboard shovel is attached to the rear suspension for clearing trenches and removing soil.
• The cutting mechanism, the chain drive must be covered with a protective cover to avoid injury.

What is it used for?

The equipment is used for such works:

• digging ditches, holes, trenches;
• loosening the soil;
• planting trees;
• arrangement of foundations;
• drainage, reclamation.

Digging a trench with a tiller is not difficult. In addition, after the trencher, neat trench walls remain, which reduces the risk of landslides, soil crumbling and allows you to dig a trench with a tiller in the ground: frozen, weakly stable.

The operation of the trencher is accompanied by:

• minimum volumes of soil after the arrangement of the trench;
• the absence of significant damage to the surface;
• neat cuts of the edges of the trench, without crumbling the soil;
• compactness;
• reasonable price;
• ease of maintenance.

The tiller attachment for digging trenches facilitates the work, does not require removal of the excavated soil. Soil loosened by augers can be easily returned to the trench after completion of the paving work.

Tiller Trencher

The production of mini-tractors and attachments for small equipment has helped private sector owners to shift manual labor onto the shoulders of mechanisms.

Tiller nozzles for digging trenches are also used by owners of home gardens, landscape designers in a cramped environment, when the maneuverability of mechanisms, productivity and low cost of work are important.

What is?

Tiller mounted trencher is a kind of mini excavator that is manoeuvrable and compact. It is used in cramped operating conditions between outbuildings, individual buildings, trees, bushes, on slopes.

trencher tillers have a reliable wheel or track base, are equipped with specially designed cutting bodies.

DIY trencher from old tiller! Trench through hard packed rock

Manufacturers strive to expand the functionality of the trencher and provide for the installation of various cutters, moldboards, plows, which provide trenching at depths of up to two meters.

Trencher in action

The operation of the unit is simple: after starting the cutting mills, trenching begins. Then the drive of the undercarriage is started, which makes the device move, and the auger or moldboard shovel moves the excavated soil on the surface away from the felling.

Of course, a self-made device for digging a trench with a tiller makes work easier, saves time, effort, money, and turns ditch digging into an everyday procedure.