Do-it-yourself self-propelled cart from a tiller

Do-it-yourself trolley cart

• Self-production
• Training
• Designing a simple cart
• The need for brakes

Self-production

This device will simplify the processing of the summer cottage, and will also help transport various goods, from hay and crops to the remaining garbage. Its production does not require expensive and complex materials, rather, most of them will be found in a home workshop. In this case, a home-made cart will be much more economical than a purchased one, because the latter will cost from 12 thousand rubles in the case of a new design and from 8 thousand when choosing a used one. The dimensions of the designed trailer depend on what kind of load it has to work with. For example, to transport 2.5 centners of cargo, the cart must have a width of 1150 millimeters, a length of 1500 millimeters and a height of 280 millimeters.

Designing a simple cart

The simplest trailer can carry from 450 to 500 kilograms of cargo and can hold approximately 8 full bags of potatoes. If you study the drawing, it becomes clear that the self-propelled cart will consist of such typical elements as a body, carrier, frame, wheels and others. The frame will be best welded from cut tubes with a round or rectangular cross-section, as well as iron corners. This should be done on a flat surface, and using electric arc welding. During work, it is necessary that the seam is uniform at all joints, which are then grinded with an angle grinder. The resulting structure will be able to operate in areas with irregularities and small differences in height. Body with frame is usually fixed using pins.

In addition, the installation of springs is recommended to minimize the shaking that occurs when driving over potholes. A dump cart cannot function without the aid of a wheel axle, which is a pin 1 meter long, the diameter of which does not exceed three centimeters. It is important to make sure when choosing a rod so that as a result its wheels do not go beyond the boundaries of the body. It will be possible to assemble the parts by welding through the support corners, as well as the frame beams with kerchiefs with longitudinal hinges. By the way, since the main load will fall on the point where the trailer is directly connected, as well as on the turning zone, they should be additionally strengthened.

The body of the dump trailer is made either of metal or wood. planks or plywood. In any case, the thickness of the material should be at least 20 millimeters, and it would be better to strengthen it with steel corners. Props are required to connect the frame and body. In their capacity, by the way, there can be strong bars of 50 by 50 mm available on the farm. The center of gravity should not cross the straight line of the wheel pin, and stiffeners are required from below and from the sides.

In addition, it is important to consider the purpose for which the cart will be used. If bags with cargo will be transported in it, then folding sides are not at all necessary. Nevertheless, for unloading, it is worth providing an opening rear wall of the body or tipping mechanisms for turning the device over. Of course, all sides are allowed to be fixed. In addition, they must be smooth from the inside.

To connect the resulting trailer to an existing tiller, you need a special part called a console. In this case, the connecting mechanism has to be removed into the cylindrical body of the longitudinal hinge and secured with a special thrust ring. This will make it possible to create the independence of the cart wheels from the wheels of a tiller or other agricultural machinery, which means, to simplify the process of driving a moving vehicle. The hitch is formed from any suitable metal piece, the length of which is determined so that the transport device is convenient to operate.

Wheels are usually assembled from scrap materials. stroller tires, combined with a central part taken from other parts. Both axles are sharpened to the diameter of the bearings of the motorcycle hub taken from the sidecar. For the wheel axle, a steel circle is required, the diameter of which reaches at least three centimeters, which will then be welded together with a longitudinal hinge and corner supports.

The bottom of the cart itself is more convenient to design from a metal plate, the thickness of which varies from 2 to 3 millimeters. Edged board, which is more affordable, but less stable, will also work.

Among other things, a seat and a footrest must be created for the driver. The seat is either attached to the hitch or mounted directly in the body.

Training

When it is decided what parameters the planned cart corresponds to, it is worth making drawings, and then calculating the amount of material required, including the channel. Craftsmen recommend based on those details that are already at hand, and if necessary, buy something. The profile pipe of rectangular or square cross-section can be easily replaced by the round one that is available. All detected parts must be cleaned of corrosion spots and covered with a rust converter with a priming function. In accordance with the drawings, some of them will have to be corrected by removing unnecessary elements. Then all that remains is to fit and combine.

Of the tools that can be useful during work, experts call a welding machine, a drill or a full-fledged drilling machine, an angle grinder with roughing and cutting discs, as well as a special device equipped with rivets.

Many professionals recommend, in addition, stock up on oil paint for metal or a special tool with a polymer filler. In the second case, the painting will be more stable and the body will not have to be painted again by the end of the season. Paint coating is carried out prior to assembly of large trailer parts.

The need for brakes

Undoubtedly, it is worth adding a braking system to a homemade trailer. Otherwise, any descent from the hill can end in tragedy. The brakes on the cart are usually released from another vehicle, such as a regular car or a tiller. The parking mechanism is considered the most suitable: with its help, you can fix the trailer in an immovable state for a long time, stop it while driving, or even leave it at an angle. You can use the brake if you press the lever or pedal.

To provide the trailer with the above function, as an option, a motorcycle brake drum and pads, as well as a motorcycle wheel spokes, are required. The implementation of the direct alteration will take place using a welding machine and pliers. Pre-used discs are freed from cables and rods and sharpened by a specialist. Next, the drums are put on the hubs and fixed at the back. The resulting empty space between the ribs will have to be filled by wrapping the ribs themselves with ordinary metal wire.

At the next stage, the discs are arranged on the axle and fastened with bushings. In addition, it is worth welding a small fragment of a metal part, for example, a corner, to the axle to prevent the disc from moving. The cables are mounted on drums and reach the place where the driver can activate the brake, usually a lever or pedal.

For information on how to make a trolley for a tiller with your own hands, see the next video.

List of required materials

• metal parts. pipes, plates, slats, sheets and so on;
• wooden parts. suitable for the manufacture of the body and frame;
• wheels from a tiller, bicycle, car or scooter;
• internal combustion engine with good power.

Also, do not forget about the different fasteners, which in each case will be different. For example, if you decide to use boards for construction, then you will have to acquire several dozen self-tapping screws, and it is best to use welding to fix metal parts.

How to Build a Electric Wheelbarrow

How to make a self-propelled cart with your own hands

Life in the country is inextricably linked with the need to constantly work in the garden or in the vegetable garden. However, it is best to move heavy objects from place to place using a special trolley, especially when it comes to building materials. In our article we will tell you everything about how to make a self-propelled cart with your own hands from a tiller, a bicycle and other vehicles. Such information will be useful to both novice summer residents and professional builders.

Unit from a motor cultivator

Any motor-cultivator that is out of order can be used to create a self-propelled cart with your own hands. In this case, you will first have to figure out the engine malfunctions (replace the belt or put new candles), and then proceed with the manufacture of the frame on which the ICE and the trolley body will be attached. It is best to use iron corners for this purpose, welding a rectangle of the desired shape from them according to pre-prepared drawings. Then the design will be more durable, and the self-propelled vehicle will be more reliable.

Self-propelled cart from an old tractor

If you have an old, unnecessary tractor that is still on the move, then making a self-propelled cart out of it will not be difficult. We simply remove unnecessary elements from agricultural machinery, for example, a driver’s seat and put in its place some kind of deep bath or a body made of wood. Such a unit is ideal for transporting heavy building materials (cement, bricks, etc.) over a fairly long distance. As an additional element, we recommend making a small metal plane on which the driver can stand.

Creation of drawings

Any work on making something with your own hands should begin with drawing up competent drawings, especially when it comes to a self-propelled cart. Without a schematic drawing in front of your eyes, it will be enough to simply make a mistake in the calculations, so do not be lazy to spend several hours so that later you do not have to redo all the work.

It should be noted that the drawing should be presented in two versions. The first one should show the body and the frame, which will be made from scrap materials. The second page of the drawing should be occupied by the internal combustion engine that will be used during assembly, as well as options for attaching it to the body and wheels.

List of required tools

In order not to be distracted while searching for the necessary tools, it is recommended that you acquire everything you need in advance. If something is missing, then you can use an alternative option (instead of a screwdriver with self-tapping screws. a hammer and nails), but this must be done wisely so that the quality of the product does not suffer. Here’s a list of the basic tools you’ll need:

• electric jigsaw and circular saw. for woodworking;
• angle grinder with discs and welding machine. for working with metal;
• a screwdriver or drill with a special attachment. for fastening a tree;
• a set of wrenches and screwdrivers. to remove unnecessary items from the internal combustion engine.

Keep in mind that this is just a minimal list of things that might come in handy in the process. It can be expanded if necessary. It all depends on what kind of cart you want to make.

Metal body and internal combustion engine from a moped

In this and the following sections, you will find information about the features of DIY garden carts assemblies. The options can be very different. For example, you can use an internal combustion engine from a conventional eighty cc moped, and also its rear wheel. In this case, there is practically no need to remove any elements. It will only be necessary to correctly attach the internal combustion engine to the metal body, with the manufacture of which there should also be no special difficulties. Also, as an additional element, you can use the braking system from the scooter by attaching cables from the pads to the handles.

Materials and tools

To work, you need the following tools:

• angle grinder for cutting parts;
• welding machine;
• welding electrodes;
• jigsaw;
• screwdriver;
• regular construction square for measuring angles.

In the manufacture of a trailed structure, the following materials and parts will be needed:

• metal profile pipes of square or rectangular cross-section;
• wheels and springs;
• duralumin sheets 2 mm thick;
• steel sheets;
• channel;
• metal corners;
• metal rod;
• fasteners.

All parts, especially if these are remnants of old metal products, are carefully inspected for damage, cracks, cleaned of rust, cut off.

How to make a cart for a tiller with your own hands: drawings and dimensions, photos, videos

Trolley trolley. trailed equipment for universal agricultural motor vehicles for transporting goods on personal and land plots. With the help of such a mechanism, garbage, animal feed, building materials, fertilizer, grain, inventory are transported.

The trailer and tiller adapter are homemade varieties made by skilled mechanics. The adapter is a longitudinal beam with its own chassis, driver’s seat and footrest. This module makes it possible to work the soil in a sitting position, as well as attach 2 equipment at once. in front and behind.

The trolley is a type of adapter with a difference in the design of the chassis.

A purchased cart for a tiller is expensive. To save financial resources, craftsmen make it themselves, design construction drawings, select the necessary materials. The process of creating such a useful vehicle does not take much time and is not difficult. Even a beginner, at least a little versed in technology, can handle it.

A brief overview will help you understand the question of how to make a tiller cart yourself with good performance.

Trolley making

In order to understand how to make a cart to the tiller with your own hands, you need to perform the following algorithm of operations:

• For the manufacture of a supporting welded rigid frame, take 5 pipe blanks, cut off the ends of an angle grinder.
• Press the clamps to the chipboard sheet and weld the joints of 3 longitudinal blanks with 2 perpendicular ones so that they create a lattice frame.
• Check the geometry of the structure with a regular construction square. The angles of the connected ribs must be 90 °.
• Install spacers between the tacked workpieces in the corners of the bottom and in the center, tack with welding.
• To the longitudinal pipes of the bottom, make tacks with a welding electrode 4 vertical racks in the corners.
• Check the perpendicularity of the corners, check the dimensions of the sides of the structure with the dimensions in the drawing of the cart for the tiller.
• Finally weld all the workpieces to each other, grind the welded seams, clean them of sagging and formations.
• The body can be made of plywood or wooden planks, while the corner joints are fixed with steel corners.
• Boards are mounted on the frame and bolted on.
• durable sides of the master are made of steel sheets. The sides can be hinged and fixed. Hinged sides of the body are considered more rational, because unloading cargo of large volumes is easier. The sides are also made of square or rectangular metal pipes. They are performed, like the frame, they are grabbed, the geometry is checked for strength and to avoid braces and deviations, they are finally welded, rigidly attached to the frame. The tailgate is attached with ordinary door hinges and equipped with latches.
• Take a metal rod with a diameter of 30 mm and a length of about 1050 mm to make an axle for wheels, connect it with a longitudinal hinge and corner supports. The length should be chosen so that the axle does not go beyond the limits of the wheels. Sharpen it to the required diameters of the bearings in the hubs.
• As a running gear, you can take a wheelbase from a scooter, stroller, wheelbarrow or other agricultural machinery. Heavy wheels from a car trailer with hubs are not recommended to be installed.
• For the manufacture of the drawbar, 2 profile pipes with a diameter of 25×50 mm and a length of about 1.85 m are taken, they are welded to the frame beam so that a triangular structure is obtained. For reinforcement in the corners, metal kerchiefs with a thickness of 4 mm are attached by welding, a plate with a thickness of 8 mm is attached in front of the trolley.
• Tipper technology provides for the installation of door hinges attached to the bottom of the beam and to the bottom struts.
• Sheathe the frame of the structure made with wooden boards, plastic or metal.
• The driver’s seat on a tiller with a trolley is installed ready-made or in the form of homemade boxes from a piece of chipboard and foam rubber sheathed with dermantin. Such boxes are necessary to hide inventory and materials.
• The machine’s parking brake can be used as a brake. Fix the brake pedal made of 6 mm thick plate on the footrest under the seat, weld 2 corners. Install the pedal in the front part, in the back. a plate with 2 holes for fastening brake cables, the ends of which are connected to a T-shaped plate with a rod.

In this way, you can make a trolley for a tiller with your own hands.

Trolley device

tillers and motor cultivators on trailers consist of the following basic elements:

• frame;
• body;
• hitch or drawbar;
• driver’s seat;
• steering gear;
• chassis.

To withstand heavy loads, a homemade tiller cart is reinforced with special stiffeners.

For a 1-axle trailer, a manual device is sufficient. A 2-axle tipper wagon with a heavy lifting capacity must be hydraulically operated against tipping.

With a lifting capacity of over 350 kg, the self-propelled cart is equipped with braking parts for safety. Mechanical brakes can be made by yourself. If these details are not taken into account, then when overloading during descent from a hill, the tiller’s trolley with its own hands will not be able to stop and overturn. In order for it to remain in the working position after disconnecting from the tiller, the stops are installed.

Basic information

Before carrying out work on the manufacture of a trailer, it is necessary to develop a detailed action plan and adhere to it.

The work plan for the manufacture of a trailer for a tiller is as follows:

• At the preparatory stage, it is necessary to familiarize yourself with the device of the mechanism, analyze its functionality depending on the power of the tiller.
• Sketch the structure. Self-made trailer diagram will greatly simplify the work.
• Calculate the dimensions of the tiller cart.
• Design a drawing of the trolley, on which to render the main units, parameters and dimensions of parts.
• Plan the principle of operation of the main and additional mechanisms, think over ways of connecting all nodes and parts, their functioning.
• Prepare a list of required materials and tools.
• Start the assembly and finishing process.

Depending on the ability to transport cargo, trailers are divided into 3 types:

• Simple 1-axle attachment for tillers up to 70 kg load capacity. Its design is simple and inexpensive.
• Universal cart with carrying capacity up to 110-120 kg. It is often used in the household.
• Trolley trolleys with a lifting capacity of over 120 kg. Such mechanisms are designed to move heavy loads, therefore, they have a more complex device, respectively, the cost of materials for the frame and cladding increases. The functionality of this technique is expanding.

Based on these parameters, the material is chosen according to its strength for the frame and finishing of the mechanism.

Do-it-yourself trolley for a motorized towing vehicle

A motorized towing vehicle (motorized dog) is a device for transporting goods, traveling through snow and wetlands. The towing vehicle itself has a caterpillar track and is complemented by a sled. A sleigh trailer is convenient in winter, provided there is a large snow cover, however, in summer or in snowless winters, using such a trailer is problematic.

Agricultural machinery manufacturers offer a wide range of trailers, adapters and carts, including those for a motorized towing vehicle. Some owners of such equipment create a cart with their own hands. Its device is practically the same as a tiller cart.

The main difference between a motorized towing vehicle, which dictates the features of the device of trailers, is a caterpillar track. These vehicles are ideal for off-road use, so the trailer must meet the same requirements.

Two types of trailers are recommended for motorized dogs: a loading platform and a skidder. Both options are difficult to implement, so it is better to adapt the finished trolley for the tiller. Drawings and dimensions for the trolley and tiller will be almost the same, so you can use any.

The main feature of the trailer for this type of equipment is the low pressure wheels. They have a high shock-absorbing effect and are excellent for off-road use. A trolley with such wheels can be used at any time of the year. This modification requires axle reinforcement from the bogie, as well as wheel attachment. All other parts of the cart can remain unchanged.

A wheelbarrow for a tiller do it yourself

A wheelbarrow for a tiller is an irreplaceable assistant in the household. Such a device allows you to transport goods (crops, garbage, building materials, etc.). You can make a trolley for a tiller with your own hands from auto parts or from individual materials. In both cases, welding and certain design skills are required. The wheelbarrow assumes the simplest design; any drawing of a trailer for tillers is suitable for its creation.

For the tiller Neva MB-2, a hinged wheelbarrow with an H-shaped coupling is suitable. This type of connection is universal and easy to manufacture. The hitching point of the wheelbarrow and the tiller is one of the most important units that receives a large load, therefore the materials for its creation must be strong, it is mandatory to check for defects (cracks, rust).

A wheelbarrow for a tiller consists of a frame, sides and wheels. If you add a seat and a steering column to it, you get an analogue of a mini-tractor. Any of the options for a wheelbarrow for a tiller can be made from improvised means, there are many photos and videos on the Internet with the process of assembling devices.

Do you use trailers, adapters and tiller cars?

Attachments

Buying a tiller without a hitch or with only one plow for plowing and turning the soil layer is in most cases impractical. A set of additional equipment allows you to significantly expand the capabilities of the unit.

In this case, it can be used for planting and harvesting root crops, for processing row spacings and hilling beds, for mowing hay, tedding it and picking it up. Trailed trolley with a seating position allows you to transport goods.

In winter, the tiller can be equipped with a front scraper and can be used to remove snow from the road. All equipment can be purchased, rather than using different homemade products. For the tiller “Neva”, for example, the manufacturer produces enough attachments.

However, often the owners still alter it for themselves. For some, the factory hitch is not powerful enough and does not withstand loads, for others there are not enough adjustments to adjust it to work in certain conditions, and still others are simply used to making the tool themselves.

tiller. affordable mechanization for field work

You can solve the problem of processing a vegetable garden by applying a tiller and using attachments to it. With the help of such devices, it is possible at a sufficiently high level to ensure plowing and cultivation of the soil, preparing it for planting the main crops, as well as harvesting. This saves time and labor costs, since manual digging and weeding even on six acres of a vegetable garden is not an easy job.

Homemade Power wheelbarrow lawn cart

When working in a confined space and with an abundance of various crops on site, the operator should have good two-wheeled handling skills. Do-it-yourself homemade hinges for the tiller are made taking into account the experience of their use for specific economic conditions. Although such structures have an unpresentable appearance, they ensure the fulfillment of the main tasks.

Tiller design features

Such an assembly consists of a drive, transmission, chassis and wheels. The tiller is controlled by levers and rods mounted on the steering wheel. For light and medium-sized units, the drive is usually a gasoline internal combustion engine. Heavier tillers are equipped with diesel drives.

Lubrication, ignition, gas distribution, cooling, fuel delivery systems and a starting mechanism are mandatory. They have their own characteristics depending on the type of motor used as a tiller drive.

The gearbox, clutch and gearbox (in some models also a differential) ensure the conversion of the engine shaft torque into the rotation of a pair of wheels. They can be pneumatic or weighted metal with additional lugs for work under load.

Tiller homemade mini tractors have a seat and an extra pair of wheels. They can be controlled or driven. Depending on the design, the tiller turns into a four-wheel drive unit with a drive on the rear or front axle.

DIY homemade products for the tiller

Complete equipment is not always suitable for business conditions. In order not to constantly cut off individual parts, not to weld stiffeners to strengthen the structure or additional brackets for fastenings, you can do everything yourself.

Even the plow and disc hiller are made by craftsmen at home. For this, one desire, drawing and material is not enough. Additional equipment will be required: a gas cutter, a welding machine, an angle grinder and practical skills in working with them.

DIY homemade products for a tiller can be made using spare parts from old cars. The trailer can be manufactured using the rear axle from the “passenger car”. If you throw out the gearbox and connect the axle shafts with a pipe, you get a reliable rear beam. Welding the frame and sheathing it with tin or board is not a problem. The springs can be taken from “Moskvich”. you get a reliable design with a decent carrying capacity.

A homemade scraper can be made from sheet metal 1–2 mm thick. If you weld stiffeners to the sheet curved along the profile, they can not only remove snow, but also be used as a bulldozer bucket for leveling soil or humus.

Mini tractors. homemade products from tiller. Self-propelled guns from tiller do it yourself

The benefits of a tiller for gardeners and summer residents are invaluable. Still, it cannot be compared with the mechanization of work with a full-fledged tractor. Anyone who had experience with a tiller probably thought about how to improve their single-axis drive.

Some craftsmen even decide to convert it into a miniature four-wheeled tractor. Currently, homemade tiller products can be found everywhere. Despite the fact that manufacturers produce quite a lot of attachments for them, our craftsmen alter them at their discretion.

Advantages of a mini tractor

The tiller is adapted for field work, but not everyone can manage it. For example, an elderly person who does not have good health will have to expend a lot of effort when maneuvering. Another point is the constant load on the legs. In order for the tiller to work the soil, he must be driven by the horns.

Anyone who has ever worked with a tiller on plowing, cultivation or other tillage, understands how much effort it takes to manage it. Hold during a jerk, direct in a rut, turn around, take back. At the same time, do not get confused in the control levers and do not go where you do not need to. often this is work in the sweat of your brow. Many tiller owners, having tried such mechanization, sell their units without adapting to their control.

Controlling a mini tractor is a completely different matter. Why walk around the field behind the machine, wasting energy, when you can operate it while sitting on horseback. The drive is the same, the speed is the same, but all this is sitting and no load. Tiller homemade products provide a sufficient level of comfort. Control levers under the hands, there is a brake.

An additional pair of wheels, set at a sufficient distance (1–1.2 m), provides reliable support. Another advantage is the ability to transport loads in a trailed trolley or a body mounted on a rear driven axle.

Homemade Tiller

Despite the fact that there is a sufficient choice (in terms of price and power) for small-scale mechanization on sale, there are sometimes original homemade products in everyday life. Not everyone can assemble a tiller from scratch with their own hands. However, a person who is familiar with technology, who has the necessary equipment and components at his disposal, can make it himself. In some cases, such designs can even compete with factory samples.

The materials for the manufacture of homemade products are usually parts of used motorcycles and all kinds of scrap metal. The engine can be used even from the Druzhba chainsaw. There are craftsmen who prefer motor scooter drives. Such motors have good forced cooling and can be used for a long time under loads even at minimum speed.

Mini tractors. Homemade products from Tiller

Manufacturing a mini-tractor “by eye” or even according to ready-made drawings, as a rule, implies the need for modifications after the first tests. Not everything can be fixed with just an angle grinder and welding.

Often there is a need for additional turning or milling work. Often, a design that looks perfect on paper turns out to be unusable after manufacturing.

For those who want to create a homemade mini-tractor from a tiller, but have no design experience, there is an affordable option. to purchase a ready-made conversion kit. It is not cheap, but all of its components are made in a factory. They are tested and precisely matched to each other and to the power plant.

This kit usually includes: a frame with mounts for the engine; secure seat; footrests with control manipulators; front beam with steering rods, wheel hubs and brake discs; protective fenders for wheels; hand-lifter attachment.

The owner, having purchased such a kit, can independently disassemble his tiller into its components and, according to the diagram, mount all the parts on a new frame.

Self-made self-propelled cart with a tiller engine

Homemade cart with a motor: photo and description of making homemade products.

Thinking, every gardener gardener knows that transporting goods, including building materials, is not an easy task with a garden wheelbarrow. Here is one craftsman who decided to make this work easier and made himself a cart with a motor.

Small-sized, maneuverable and easily controllable, you can do it yourself.

Materials needed:

• two wheels from a passenger car and one from agricultural machinery;
• engine from a tiller (a 6.5 hp gasoline engine is used here);
• rear axle from a passenger car;
• profile pipe;
• sprockets and chains from motor vehicles;
• wheel;
• tension rollers and timing belts;
• nuts, bolts and springs;
• sheet metal;

Here is a self-propelled cart shown in the photo.

The following shows the manufacturing process of the cart.

We take the rear axle from the car and shorten it, cut off the stockings and shorten the axle shafts.

The frame for the trolley can be welded from a profile pipe or channel.

We attach a large sprocket to the axle shaft of the differential drive gear. The engine will be installed on the frame cross members and the corner welded to the left in the direction of travel outside the spar opposite the cross members.

We install a small pulley on the engine shaft, put the belt drive on a large pulley with the required gear ratio. We attach a large pulley to the shaft on two bearings in a housing (pipe section) welded to the rack.
On the other side of the shaft we put a small sprocket, which we connect with a chain with a large sprocket on the semi-axle of the differential drive gear to ensure the desired gear ratio.

This design reduces engine speed and increases tractive effort.

To install the steering wheel, we will make a narrow frame from a profile pipe and attach it to the side members of the main frame using two inclined struts and two jibs welded to the near cross member.

At the end of the narrow frame, from the inside, we attach a wheel rotation unit consisting of an axle, bearings, a housing and a coupled sprocket. To the lower end of the axle we weld a cross member with a rack, at the bottom of which we attach the wheel axle.
On the other side of the narrow frame, mount the roller from below and connect it to the sprocket on the wheel axle with a chain. On top of the frame in the center, we weld the steering wheel shaft rotation unit, at the lower end of which we fix a paired sprocket that tightens the chain from the outside.

Now we will make a belt clutch. Under the lower branch of the belt, located closer to the wheelbarrow, we attach the tension roller to the bracket, which we weld to the axle and fasten with two supports to the narrow frame. On the other side of the axis, we attach the pedal, placing it on the left in the direction of travel. If you press it, then the roller, rising, presses the belt to the pulleys and includes a direct transmission.

Under the lower branch of the belt, located closer to the wheelbarrow, we fasten the tension roller on the bracket, which we weld to the axle and fasten with two supports to the narrow frame. On the other side of the axis, we attach the pedal, placing it on the left in the direction of travel. If you press it, then the roller, rising, presses the belt to the pulleys and engages a direct transmission.

Between the wheels, we create a support for the swing frame made of a shaped tube that can tilt forward. To it we attach a container made of sheet metal and thin shaped pipes with three vertical and one inclined side in front.

Well, the self-propelled car is ready to go! The cart is very convenient and easy to operate, we look

Body

It is hammered together from 20mm planks with steel corners attached to the corners. The trolley body is attached to the frame through three strong support beams made of 50×50 timber.

Trolley for a tiller do it yourself drawings, photos, videos

In the garden or in the garden, a tiller is one of the most useful things. With its help, you not only easily cultivate the land, but also transport a lot of necessary things: hay, fertilizers, potatoes, fuel. But how to do this if a standard tiller does not have a trailer? There is a way out. a do-it-yourself cart for the tiller is made, (the drawings are given below) is quite simple, and this will save a lot of money.

Simple do-it-yourself trolley cart drawings

The tiller trolley can carry a load of 400-450 kg plus the weight of the driver. She easily carries six or seven sacks of potatoes without overloading.

Tiller trolley drawing

• 1. bracket for tiller attachments;
• 2. console;
• 3. carrier;
• 4. footboard from planks20;
• 5. driver’s seat made of s20 board;
• 6. frame;
• 7. body made of s20 board;
• 8. support beam from a bar 50 × 50, 3 pcs.;
• 9. bolt М8;
• 10. a thrust ring made of pipe st.58 × 4;
• 11. a wheel from a motorized carriage, 2 pieces.

The carrier of the bogie structurally contains only a few parts, which are fastened together by welding. The most congested part will be the coupling of the drawbar to the turning part. Therefore, in this place you need to install additional stiffeners.

Swivel unit

console,
2. anthers,
3.6. bearings 36206,
4. case,
5. spacer sleeve,
7. distance sleeve,
8. washer,
9. nut М20 × 2.5,
10. oiler,
11. drawbar.
The driver sits on a semi-rigid wooden seat cushion in front of the body. The driver’s hands hold on to the levers of the tiller, and with his feet he rests on a wooden footboard framed from the corners on the drawbar of the carrier.

Wheel axle blank

For it, you can take a steel circle with a diameter of at least 30 mm. The axis is connected by welding with a longitudinal hinge and with corner supports. Select the length of the axle so that the wheels are under the body.

Wheels

They are taken from the stroller together with the hub assembly. Both ends of the axle are turned to fit the diameter of the hub bearings.