Hand mowel stalling gasoline stalling. The causes of the malfunction and their elimination

The trimmer for the grass works but does not mow the reason

If the lawn mower stops when pressing the gas, then the reasons may be the following.

• The most common option is a fuss of adjusting the carburetor, which occurs with significant loads on the drive, after a prolonged inaction of the mechanism or when it is used in severe conditions.
• The clogging of the fuel valve, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. Also, a tensile of the fuel hose can occur up to its rupture, caused by the action of a significant load.
• Clogging of the saapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

Checking the ignition coil on the spark

It is necessary to pull the wire out of the trambler. After that, the wire must be brought to a metal element and rotate the engine with a starter. If there is a spark, then the ignition breeder is out of order. If it is not visible, you need to proceed to check the coil.

If the problem is in the trimbler, you need to start checking with its contacts. Problems can cause oxidation, probes in the insulating layer or rotor malfunction. If you notice problems with the rotor, it must be replaced with a new element.

During the diagnosis of the ignition coil, check the state of the winding. Typically, the absence of a spark is caused by a short circuit inside this part. If you find its signs, we advise you to buy a new coil and install it on the car. Also, the ignition coil can damage overloads caused by faulty high.voltage wires or spark plugs.

The coil check is performed as follows:

• The car should be in a dry room;
• It is necessary to remove the dirt from the lid of the spark plug-distributor and remove it;
• crank the crankshaft of the motor so that the contacts of the trambler are in a closed position;
• turn on the ignition and bring the high-voltage wire of the distributor to the metal part of the motor by 3-7 mm.

It will also tell you whether the ignition coil in the replacement needs. The most suitable option is to test the coil on special equipment in workshops. This procedure checks the work of the coil in different modes.

To check the spark on the candles, they must be unscrewed

Pay attention to the state of contacts, the presence of soot or oil. All mud elements must be removed even before the diagnosis. Do not forget about the correct gap between the electrodes

Do not forget about the correct gap between the electrodes

If a discrepancy has been discovered, the side electrode carefully bends. Like the coil, the spark plugs can be checked qualitatively only on special equipment

Why will the chainsaw be stalled and zapayed when the gas is pressed

Chainsaws are quite reliable and simple design. Therefore, if you properly take care of them and process them on the basis of the recommendations of the manufacturer, then they fail, very rarely and various kinds of breakdowns are quickly eliminated. But if you are faced with this situation and want to personally repair your tool, without turning to the professionals for help, then we will delve into the information provided below.

In fact, it is unambiguous and accurately impossible to determine the reason why the tool does not start or stops when pressing gas, since a lot of factors affect this. But do not forget that, starting with the fact that the chainsaws are equipped with a simple two.stroke engine, conditions such as lubrication, fuel, sparks and air are important for its effective operation.

Therefore, the carburetor directly participates in the preparation of the fuel-air mixture, the filter cleans the air of dust, the ignition unit and the spark plug create a spark, and there is a lubricant in gasoline.

That is why you should look for the reasons for this kind of failure in a sequential order, starting directly with simple and gradually moving on to complex. And this is an important factor in the correct repair, since a person who, without hesitation begins to analyze the carburetor, leads him to risk. Since this type of unit should be repaired or adjusted directly in special workshops (read about the regulation of the carburetor).

There is no spark and chainsaw does not gain momentum

The chainsaw stops when pressing the gas due to the fact that neither spark. This can happen when there is no good contact between the tip of the candle and the wire (high voltage). However, if this type of connection works correctly, but there is still no spark, then the whole reason. This is an incendiary block (electronic)

It is important to note that details of this type cannot be repaired, so they can only be replaced

Do not forget that by studying the spark plug, you can get significant information about the breakdown of the chainsaw. Since if its surface is dry, then the reason for this is a cylinder, which is not directly included in the fuel. That’s why you will have to step by step by step by step by the entire spectrum of his presentation. If the candle is covered with black carbon, this means that the carburetor does not work properly, that is, it either supplies a lot of fuel or pours oil directly into gasoline.

If you put the cable instead of the fishing line, not having the opportunity to let it go, securely fix the two ends of the cable and cut them off with welding (a drop of molten metal prevents cable unturation). Such a tool clogs grass at a time. Cuts shoots in a thickness thick. Not so afraid of stones as a disc. However, there is a problem: when wear, pieces of cable threads break off, and these twisted wires remain at the place of mowing. The offensive on them can lead to injuries.

But pieces of cable left on the field. This is half the trouble. The fishing line for the trimmer, breaking off, weakens the dynamic shocks of transmission and engine, the cable does not give such an opportunity. Result. Quick wear of the brush.

Why is a Chinese lawn mower not developing momentum?

The trimmer for grass is gaining momentum, a very common problem and of course not always a familiar solution.

Also, the ignition coil can be broken in electrical equipment. In this case, the brush does not start or does not start and works with interruptions, and then stops, or does not start at all when hot.

You can check the serviceability of the coil in the same way as when checking the spark: unscrew the candle, lean it against the trimmer body for the grass. If there is no spark when you press the starter, or it appears each other, you need to change the coil.

Continuous work of the shieldcorse is indicated in the instructions for the trimmer for the grass. On average, kosim for 15-20 minutes, after which we turn off the trimmer for the grass and let it cool for 3-5 minutes. Weather conditions also affect the duration of continuous work. In hot weather, during skewing of high grass, thickets of weeds, under a large load, a trimmer for the grass overheats faster.

Many brush problems arise due to incorrectly prepared fuel mixture. In two.stroke engines, the lubricant is carried out with special oil (not ordinary engine oil!) Mixed with gasoline. If the oil does not mix with gasoline, the brush will quickly fail. Mix oil / gasoline in the proportion indicated in the instructions for the trimmer for grass. This is usually 1:40 or 1:50.

The question often arises: the proportion of 1:50 is how much oil and gasoline?

We identify the cause of the malfunction

To repair the lawn mower yourself, it is best to be guided by the principle of “from simple to complex”. First, check if there is enough gasoline in the tank. If the mower stopped starting after wintering, it is worth draining the old fuel and replace it with a new. Sometimes low.quality gasoline comes across, which can give a precipitate or even delay in the winter, and some gas mowers are very sensitive to fuel quality.

If there is confidence as gasoline, but the lawn mower does not show signs of life, the next thing you need to do is check the spark. To do this, remove the wire with a cap from the candle and twist it with a special candle key, which should go with the lawn mower. Then throw the cap on the candle, attach its threaded part to the metal part of the engine and ask someone to pull the starter. At this moment, a bright blue spark should appear, which is clearly noticeable even during the day. Keep in mind that you need to lean the candle against the clean metal surface of the engine, which is not covered with paint and which can be current.

Ways to eliminate breakdowns

Subsequent work is likely on the carburetor:

• cleaning and adjustment of the fuel supply valve;
• similar work with a valve producing redesigned gases and pairs (after burning fuel);
• replacement of the spring more weak on the entrance valve;
• restoration of the tension of the carburetor cable;
• replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
• changing the rotor damper disk;.
• Change of faulty wire or ignition coil.

Immediately after the start

Smelting Motokos or a trimmer for the grass after starting is justified by subsequent reasons:

• impressive of previously adjusted valves;
• first the wrong settings of the valve mechanism;
• clogging with deposits of the fuel supply valve;
• the hose is worn or poorly annexed.

Due to the violated method of injection of a fuel, a lawn mower or a trimmer for grass is very vibrated in work.

When pressing gas

If the lawn mower stops when pressing the gas, then the reasons may be the following.

• The most common option is a fuss of adjusting the carburetor, which occurs with significant loads on the drive, after a prolonged inaction of the mechanism or when it is used in severe conditions.
• The clogging of the fuel valve, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. Also, a tensile of the fuel hose can occur up to its rupture, caused by the action of a significant load.
• Clogging of the saapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

The gasoline trimmer for the grass starts and stalls

Why is a trimmer not starting for grass gasoline? Reasons and their elimination

Recently, a gasoline trimmer for grass has acquired the status of one of the main tools in the arsenal of summer residents. And this is not surprising, because a motorized braid for grass allows you to quickly put a personal plot in order. However, sometimes it happens that the trimmer for the grass does not start hot and even on cold. In such situations, you have to independently establish the cause of the malfunction. Let’s find out what to do if a trimmer does not start for grass. The reasons that most often lead to such troubles will be considered further.

Diagnostics strategy

Where to start the diagnosis of malfunctions if a trimmer is not started for grass? In situations where the tool stalls immediately after starting, it is worth examining the following units:

It is the breakdown of the above locations that most often leads to the fact that a trimmer for grass is poorly started. Let’s look at how to eliminate such troubles.

Checking the fuel mixture

Suppose you don’t start a trimmer for grass. In this case, the first thing is to check whether the fuel is enough in the tank, as well as evaluate the quality of the fuel mixture. To refuel a motorized unit, it is necessary exclusively high.quality gasoline. It is recommended to use fuel, the brand of which is not lower than AI-95. Refueling a trimmer for grass with fuel of unknown origin, not bought at a gas station, is fraught with frequent failures in the work of the tool. This can cause a breakdown of the cylinder-piston system. Repair in this case often exceeds the cost of the device itself.

Why is a trimmer not starting for grass gasoline? Incorrect preparation of the fuel mixture may also lead to this, which consists of oil and gasoline. The proportions in which the specified components are connected are indicated by manufacturers in the guide for the operation of a trimmer for grass. Preparing the fuel mixture is extremely not recommended in large volumes, that is, for the future. Indeed, with prolonged savings, there is a loss of the determining properties of the substance. Therefore, if a trimmer for grass does not start, it is worth draining the old fuel and use freshly prepared fuel mixture.

Read which trimmer for grass is better than rotary or vibration

Diagnosis of the candle channel

What to do if the used fuel mixture is in perfect order, but a trimmer for grass is still not started by gasoline? The reasons for the refusal of the mechanism may lie in excessive moisture of the candle channel. To diagnose and eliminate the problem, it is necessary to do the following:

• To twist the candle. Wipe it thoroughly, and then dry it.
• Drain excess fuel in the chamber through the corresponding candle hole.
• Clear the old candle if there is a dozen on its surface. Cope with the task will allow the use of a conventional ladies’ nail file or file.
• When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the lumen.
• Collect a functional block back.
• Try to start a trimmer for grass.

It is recommended to perform a candle channel to dry for at least half an hour. However, in no case should you resort to the calcination of its elements. After all, heating the spark plug can lead to its final corruption. Что предпринять, если обслуживание функционального блока было выполнено в соответствии вышеуказанным рекомендациям, но триммер для травы не заводится, искра есть при этом? In this case, it should be treated with gasoline threaded connection. The latter does not need to be saturated abundantly fuel. It should only be slightly moisturized. Resort to such actions should be to ensure the ignition. After all, no matter how much the candle gives a strong spark, in an absolutely dry chamber there simply will not be something to ignite.

The lawn mower stalls

Carburetor adjustment, well start

,stalling when pressing gas. My Skype: Ork.Vitek tel. 380979677418

The lawn mower stalls or suffocates when you press the gas

Even more information about the repair and choice of tools on our website www.Looktool.Ru, we are happy for everyone.

If even in this case a trimmer for grass does not start, it is worth evaluating the quality of the contact between the high.voltage wire and the candle. In the absence of a spark (in the presence of a reliable connection between the indicated elements), most likely, the problem is caused by breakdown of the ignition unit. In this situation, you will have to turn to the services of masters who will reinstall the knot.

Checking filters

Another common cause, due to which a trimmer for grass does not start, is the presence of a blockage in the filter area. To confirm the conjecture, just dismantle the indicated block and try to start the unit without it. If the engine of the trimmer for the grass has launched, most likely you will have to replace the air filter or at least perform a thorough purge of the old. In the presence of abundant contaminants on the surface of the filter element, it is necessary to use a new grid. Relying to such actions, you should not leave a suction pipe at all without a filter. After all, rush in this case can lead to the need to repair the entire piston group of the unit engine.

Cleaning the soundtress

Often the engine of branded models of trimmers stalls as a result of clogging of the soundtress. The main task of the specified component is to align the pressure in the fuel tank. In the case of contamination of the node, a vacuum is formed here, which significantly complicates the supply of fuel. Eliminating the malfunction allows the cleaning of the saapon using a conventional sewing needle.

Diagnosis of the graduation channel

The stable functioning of a trimmer for grass can be impaired as a result of laying dirt in the graduation canal or the formation of a blockage on a muffler grid. This problem most often occurs during the operation of older generation trimmers. The issue is being solved by dismantling the anti.diploma mesh and its cleaning.

How to prevent sudden breakdowns during the operation of a trimmer for grass?

So that the unit is always in a functional state, it is worth observing several simple rules:

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.

To store the tool in cold weather, you need:

• completely drain the fuel;
• disassemble the lawn mower, wash and clean all available components;

• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

The reasons for the weak.speed trimmer for grass

If users complain to the trimmer for grass, which does not gain momentum, this means that it works normally on idle, and when pressing gas does not develop the necessary power. This can happen as a result of a long downtime of the apparatus without activity. These problems are typical for gasoline devices, including the Husqvarna 128R, STIHL FS 38 and Hitachi different modifications.

Working with a trimmer, you need to monitor its behavior all the time. a drop in revolutions and unusual noises signal the malfunctions in the aggregate. Sometimes you give gas, and the trimmer for the grass swims. In such cases, the work should immediately be suspended, let the mechanism cool and start searching for possible problems. They can be of a different nature of both the technological plan and external factors related to the conditions and features of the operation of the device.

External factors

Several factors that are not related to its breakdown affect the reduction of revolutions:

• filter pollution due to the hit of particles of dirt and dust in it;
• use of poor.quality fuel;
• incorrectly prepared mixture (relevant for trimmers with two.stroke gasoline engines);
• pollution of the muffle of muffler particles of vegetation, soil elements and other objects.

In this case, in the second and third cases, the formation of a soil in the combustion chamber is formed, and the elements of the carburetor are clogged.

technical issues

The technical problems of the lawn mower mainly occur in the fuel and ignition system. You can cope with them yourself.

• Когда ручная косилка не заводится или глохнет, проблема может быть связана со свечой. The dark cargo speaks of poor carburetor adjustment and low gasoline quality.
• The reason for the incorrect operation of the trimmer for the grass may be clogged fuel hose. Filters are also often clogged.
• Another internal problem. the muffler is covered with soot. From this, the turnover of the grass for the grass falls strongly. Output. you need to clean the muffler.

What to do if a trimmer for grass stalls when you press the gas?

So why is a trimmer stall for grass when pressing for gas ? There may be several reasons for this problem.

• The carburetor was resolved after an unsuccessful wintering or after too intense use of motorcycles. The gasoline trimmer for the grass operates on the air-fuel mixture that the carburetor prepares it. With improper adjustment, this mechanism prepares a depleted mixture that is not capable of providing the engine with quite high speeds. You can understand about the problem with the carburetor by the characteristic vibrations of the lawn mower.
• You will learn about the clogging of the fuel filter by the fact that the trimmer for the grass starts and stalls. In other words, the flow of fuel is enough to start a motorcycle, but is no longer enough to maintain the engine in work. It may be possible to solve the problem with weakening valves on the filter. If not, you should rinse the filter in solvents and blow it with compressed air. If after and this is not solved the problem, then you should purchase a new fuel filter.
• If the engine stalls at speeds close to maximum, then perhaps the problem with the saope that regulates air access to the gas tank. If the fuel consumption is too fast, characteristic when you give gas, rarefied pressure is formed in the gas tank, due to which the fuel flow into the engine is reduced.
• The engine stalls when opening the damper. The problem, again, is associated with a carburetor, which, due to an excess of air, prepares a depleted air-fuel mixture, which is not capable of ensuring engine operation.

Why stalls the lawn mower: reasons and solutions

The reason why your tool abruptly stops working, namely the engine does not gain revolutions, breaks them off, or “stalls” in popularity, there may be more than one. Often this is to blame not only the engine itself, but also the adjacent systems, unit nodes, completely different details related to the preparation of the fuel-air mixture, its quality, transportation to the tool of the tool. Consider the most typical situations:

• He is not gaining momentum. The engine drive mechanics may be damaged or there were problems with the carburetor, but the main reason should be considered clogging of the air filter. To change the situation, it must be removed, cleaned, and if it is no longer subject to the latter, then change for a new one, promptly making an order on our website. Also, there will not be a turn of the braid for grass, if the cable from the carburetor constantly flies. disassemble the unit and firmly fix it, or buy a new one if cracks are found on the element, other types of deformations.
• At high speeds. The lid on the gas tank is clogged. it needs to be cleaned or new. often the reason is a sipped carb. We submit information on the correct adjustment of all screws in information articles. Check the quality of the fuel hose and change it to a new one if necessary.
• When heated. It occurs in moments when the fuel in the carburetor literally boils. It can also appear in the options if the carba damper is more rare, rotary type (not disk). The only option would be to replace the carburetor with a new. There is another option for a broken wire or ignition coil. In this case, change the element of the latter.
• Starts and stalls (immediately after launch). Solved or incorrectly adjusted carburetor is the main reason for this situation. Calm vibration will indicate an uneven supply of fuel, and competent adjustment of the node will help to correct the situation.

We hope you found the right answer to the question: why the lawn mower stalls, and all the proposed catalog details today, as always, are at your service. You need a piston trimmer for grass, a new carburetor, or the elements accompanying the operation of these systems. you will find everything in the open spaces of the Benzo SIP store.

What to do if the lawn mower stalls when you press the gas

Most often during the periods when the lawn mower stalls when the gas is added, the cause will be the air damper, more precisely, its condition: it clogged. Structurally, the part is located in the place where the resulting fuel is sprayed behind it, and, accordingly, the product collects all inclusions in low.quality gasoline. To eliminate the problem, you just need to clean it. The same situation can occur with a filter clogged, but it is eliminated similarly. Total, we specify the reasons for which the tool is led to the gas to the stalled state:

• a clogged air damper;
• The clogged filter is fuel, and when you give gas, this is especially noticeable;
• the air of the crankshaft shaft occurs;
• damaged gasket between the cylinder and the carb.

When you cleared, washed and blowing the elements, but again the lawn mower stall when you press the gas-replace them with new ones, check the quality of the fuel, as well as the literacy of the proportions of the cooked mixture. When opening the air damper, the tool will stall for the following reasons:

• Dosage carburetor.
• The appearance of cracks on the fuel hose caused air leaks.
• The occurrence of problems with the oil seals.

In the process, situations arise when the lawn mower at high speeds is subject to a similar sharp stop. It occurs for the following reasons:

• due to problems with the circulation of the fuel mixture;
• with air leaks;
• The fuel intake hose is poorly connected or cracked and cannot be used;
• stab or clogged the valve of the cover of the gasoline tank;
• The carburetor was resolved.

In most cases, nevertheless, the cause will be a carburetor and related filter, hoses. If you need cutting gear or trimmer heads, then our site will also offer them to buy them with gasoline tools and components for them.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

• Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
• A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
• The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
• Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
• Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

• First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
• Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
• Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
• Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.
• If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
• After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

• completely drain the fuel;
• disassemble the lawn mower, wash and clean all available components;

• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

At idle

At single speeds, the common reasons for stopping a trimmer for grass are as follows:

• reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel mixture;
• clogging of the throttle;

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.

To store the tool in cold weather, you need:

• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

Why the lawn mower is not started, we eliminate problems

When caring for a personal plot, summer residents at times are faced with the fact that the lawn mower is not started. There are many circumstances of the instrument failure. A trimmer for STIHL grass is poorly started. For proper diagnosis of interference, the owner of useful in the country’s divetor should know the device and mechanism of operation of its individual parts.

Since the gasoline trimmer for grass refers to complex devices, before work you need to closely study the annotation for operation. Very often it is simply ignored, or they get acquainted with it superficially. As a result, when the tool stalls or renounces the question, the question arises. “why the lawn mower is not started

?»A long seasonal break in work, improper storage and untimely maintenance of a trimmer for grass, will deliver a lot of trouble to the summer resident, to eliminate the reasons.

Additional tips

First of all, what you should remember when acquiring this kind of tool is that certain details of the saw must be changed to new ones after their service life (passport) is over. It is for this reason that the instruction should always be at your hand, since everything is described in detail there in detail.

Such details include: asterisk (leading), tire, part of the system (anti.vibration), as well as a chain. Since do not forget that if this “filling” is not changed at a new time, then these worn spare parts will negatively affect the rest of the chainsaw. It is for this reason that quite often make a check of the depth of direct production of teeth. Remember that it should not be higher than a week 0.5 mm.

Muffler, as the reason that the saw stalls at the load

Here is another reason why the chainsaw stalls when pressing the gas. muffler. It is this part that can interfere with the full operation of the tool in cases where it is contaminated with directly exhaust resinent sediments. To do this, you just just need to clean it on.