Hitachi lawn mower stall when you press the gas. Diagnosis and elimination of electric motor problems

Hitachi trimmer does not develop a moment

If the lawn mower does not start or immediately stalls after starting, it is necessary to sequentially check all the main nodes and assemblies. The test algorithm is as follows:

• Fuel tank (fuel quality);
• Candle and candle channel;
• Air filter;
• Fuel filter;
• Breather;
• Graduation channel.

These nodes are most often source of basic problems, which can be eliminated after a thorough inspection.

Check the fuel mixture

Before starting the engine of a gasoline braid for grass, check the presence, and the quality of the fuel mixture. Do not save, do not greedy and “do not smarter” in this matter. Repair or replacement of the piston group will cost you too much (sometimes up to 70% of the cost of a new tool). Prepare the oil fuel mixture strictly according to the instructions. Calculate its number from real needs. Excess gasoline left after work loses its qualities over time.

We diagnose a candle and candle canal

If the quality of the fuel mixture is not in doubt, and the lawn mower stalls when starting, then a flooded candle may be the reason. Here, a regular candle key is suitable for repair (every motorist has probably has a spare candle.

• We twist the candle and wipe;
• We thoroughly dry it (you should not bake it);
• Excess fuel in the chamber we drain through the candle hole and dry it;
• We clean the old candle from the carbon on a sugar or a ladies’ file;
• We set a gap with a distance of 1 mm (you can check with any coin);
• We return everything to place and try to start a trimmer for the grass.

If the working candle is working, the nest, where it is located completely dry, and the lawn mower does not want to start, lubricate the threaded connection with gasoline. It should be slightly moisturized. No matter what wonderful spark gives out a candle, there is simply nothing to light up in a dry chamber.

If the trimmer engine for grass still does not start, such a cause as the lack of spark due to weak contact between candles and a high-voltage wire should be excluded. If the connection is of high quality, and there are no sparks, most likely, you have “flew” the ignition unit. Here you can’t do without a master, t. to. The part is not repaired, but sold by a whole knot.

Diagnosis of the filters of the lawn mower

Another reason why the gasoline braid for grass stalls is an air filter. To exclude it, try to remove the filter and start a trimmer for grass without it. If it turns out, then you will have to change the air filter to a new one, or at least blow and carefully clean the old.

You can’t start a gasoline trimmer for grass due to contamination of the fuel filter. This is the next stage of our algorithm. Here we check the state of the filter element and, if necessary, change it with the new. When replacing, try not to leave a suction pipe without a filter, this is prohibited by any operating instructions. Rush can turn into the repair of the piston group of the engine.

Sapun and graduation channel

Often, “delicate” branded models of benzos are not launched and stall due. The main function of this element is to align the pressure in the gas tank. When clogging this node, a vacuum is created in the tank that prevents the supply of fuel. Eliminate the malfunction can be cleaned by cleaning the sounds. You can use a regular needle for cleaning.

The normal operation of the cos with internal combustion engines can be disturbed due to the entry of dirt into the exhaust channel or clogging of the muffler grid. There is such a problem on the models of the older generation. You can solve the issue with traditional cleaning and removal.

Hitachi CG22EAS-NB lawn mower

Hitachi gasoline unit will be an excellent assistant in the fight against low excess vegetation in small areas. The ability to install different types of cutting tools (fishing line for a trimmer or knife) allows you to remove both dry shrubs and the most soft grass.

The model has an improved New Purefire exhaust cleaning system, so there will be not so many harmful substances during operation in the air. A reduced fuel consumption will make it possible to mow for a long time without the need for periodic adding gasoline.

• Power. 0.86 liters.With./ 0.63 kW;
• Engine capacity. 21 cubic meters.cm;
• The volume of the gas tank. 0.44 l;
• Carburetor. Walbro;
• Type of drive shaft. hard.

A convenient Hitachi bike handle will be convenient for holding both right.handedness and left.handed. The upper engine placement will allow you to work even after rain, because moisture from vegetation will not fall into the “heart of the mechanism” and will not disable it.

A special launch complex S-START guarantees a very light and relaxed start, and a small weight (4.4 kg) will allow you to control the machine without much physical effort even to a schoolboy. A reliable protective casing will save the operator from the possibility of damage.

An enlarged start button will launch Hitachi without removing gloves. As for the gearbox, it belongs to a removable type, allowing you to turn the motor into a power unit. You can learn about the features of operation and the specifics of repair work thanks to the leadership presented on our portal, which describes many useful points in detail.

Why stalls the lawn mower: reasons and solutions

The reason why your tool abruptly stops working, namely the engine does not gain revolutions, breaks them off, or “stalls” in popularity, there may be more than one. Often this is to blame not only the engine itself, but also the adjacent systems, unit nodes, completely different details related to the preparation of the fuel-air mixture, its quality, transportation to the tool of the tool. Consider the most typical situations:

• He is not gaining momentum. The engine drive mechanics may be damaged or there were problems with the carburetor, but the main reason should be considered clogging of the air filter. To change the situation, it must be removed, cleaned, and if it is no longer subject to the latter, then change for a new one, promptly making an order on our website. Also, there will not be a turn of the braid for grass, if the cable from the carburetor constantly flies. disassemble the unit and firmly fix it, or buy a new one if cracks are found on the element, other types of deformations.
• At high speeds. The lid on the gas tank is clogged. it needs to be cleaned or new. often the reason is a sipped carb. We submit information on the correct adjustment of all screws in information articles. Check the quality of the fuel hose and change it to a new one if necessary.
• When heated. It occurs in moments when the fuel in the carburetor literally boils. It can also appear in the options if the carba damper is more rare, rotary type (not disk). The only option would be to replace the carburetor with a new. There is another option for a broken wire or ignition coil. In this case, change the element of the latter.
• Starts and stalls (immediately after launch). Solved or incorrectly adjusted carburetor is the main reason for this situation. Calm vibration will indicate an uneven supply of fuel, and competent adjustment of the node will help to correct the situation.

We hope you found the right answer to the question: why the lawn mower stalls, and all the proposed catalog details today, as always, are at your service. You need a piston trimmer for grass, a new carburetor, or the elements accompanying the operation of these systems. you will find everything in the open spaces of the Benzo SIP store.

Diagnosis of malfunctions

All the prerequisites why the lawn mower is not started can be systematized by the specifics of the operation of individual units. The service center is systematized:

• Motor malfunction (piston wear, bearing malfunction, crankcase crack);
• Fuel consistency supply malfunction. clogged pores of an air filter or a malfunction of a carburetor;
• the ignition system does not work;
• A malfunction of a mechanical disposition. a leak of hoses, broken wires under a braid, rupture of the tubes.

The user first needs to check if there is a fuel in the tank. Starting in agreement with annotation, putting the saw on the side. Set the air damper to the position “Closed”, pump up fuel, turn on the ignition and produce 3-4 sharp jerks by the starter. STIHL 250 chainsaw when pressed on gas stalls, stalls, she worked on gas. If the engine has earned, open the air damper. Stihl 250 chainsaw when pressed on gas stalls, what. The lawn mower is not started. we repeat the operations with a slightly open air damper.

If you are unsuccessful, we begin to find the reason for the refusal:

• check the quality of fuel;
• make sure the operability of the candle and the cleanliness of the candle canal;
• check the cleanliness of the air filter;
• Make sure that the fuel filter is not clogged;
• Check the cleanliness of the bastard;
• Clean the exhaust channel.

complex reasons will be detected in the diagnosis of a malfunction, leading to the overhaul of the carburetor. Such reasons include clogging of the internal channels of the carburetor, wear on it gaskets and violation of the tightness of internal halls with a vacuum loss. DIY lawn mowing repair, if it does not start, will require patience.

Asseting device and common malfunctions

The easiest way to give the lawn mower for repairs, allocating a certain amount of funds from the family budget, operational and high.quality repair with your own hands is no less simple and convenient to understand the design of the lawn mower and fix all the problems.

The massive and piece manufacture of trimmers is based on the use of generally accepted technology, the typical design scheme consists of certain elements and parts, it is important to know them when carrying out independent repair work:

• top part. The basis of the entire structure, where all important elements are collected, such as the starter, carburetor and the engine of the lawn mower;
• middle part. Hollow rod, inside it is a cable connecting the engine and gearbox, which sets the cutting fishing line for the trimmer. In this part there are mounts for the distribution of weight of the entire structure and a belt for fixing a trimmer for grass on a belt of a person using a trimmer for grass for its intended purpose;
• Bottom part. It has a gearbox and cutting elements that are hidden under a practical casing, which protects the user. The casing provides an increased level of safety, preventing large fractions of garbage, pebbles and glass in a person while working with a gas station.

The most common and often encountered, subject to independent correction of the breakdown of the unit can be called the following problems:

• engine malfunction, due to which the lawn mower is not started and does not work;
• enhanced vibration of the bar motorcosa, which complicates its targeted use;
• increased overheating of the gearbox, its accelerated heating during operation;
• slow and weak functioning of the cutting fishing line at insufficient speeds;
• the clogging of the starter grill causing the engine overheating and its refusal to work;
• rapid and frequent clogging of the carburetor due to the use of poor.quality fuel;
• clogging of the air filter in case of non.compliance with measures to care for the device.

All these problems can lead to the fact that the device will lose its ability to work before ordering the necessary spare parts for non.bosomeds should be carried out by a visual inspection and diagnosis of the device.

Special attention is required by individual spare parts and assemblies of the device, to verify them, you will not have to turn to a professional master, a complex of diagnostic measures will help to identify a consequence of the occurrence of a loss of performance.

The lawn mower stalls

When purchasing a lawn mower, you need to be prepared for the fact that, as in all other similar tools, it may also have breakdowns that will require repairs.

However, do not immediately run to the service center and pay a lot of money to the masters who convince you of a serious malfunction in the device.

The lawn mower stalls at high speeds

Perhaps the most common complaint related to gasoline trimmers sounds like this: “The lawn mower stalls”.

Of course, the reason for this may be a rather serious malfunction. However, most often the situation is much simpler than it seems at first glance.

To cope with such a problem, first of all, try to deal with its causes on your own, because, having found out the reason, it is much easier to fight the problem, and sometimes it is even self.destructive.

In fact, the reasons are when the lawn mower stalls at high speeds, there are quite a lot of these reasons.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

over, the lawn mower can stall due to poor fuel flow into the carburetor

Why then the device starts up, ask you?

The reason for this is that at first the fuel gradually falls into the carburetor and is enough for work with increased power.

However, then it is produced and at large speeds the engine begins to stall.

As for the carburetor, here the problem may also be that its body is too pulled.

The reason that the lawn mower stalls at high gas speeds may also be an air leak.

We are talking about the possible presence of a place through which air can pass during the heating process of the engine.

Among other things, do not forget to check the fuel intake hose. The problem may be that it is weak or cracked at all.

These are the main reasons why the gas mowl can stall.

The lawn mower stalls at high engine speeds

During operation, a situation arises when, when pressing the fuel supply key, the aggregate turnover begin not to increase, but to decrease. A malfunction of this nature can be caused:

Fuel hoses Motokos with filter

• etching of atmospheric air into the combustion chamber;
• problems with the circulation of a mixture of fuel;
• clogging the saapun in the lid of the fuel tank (cleaning the hole with a thin sewing needle);
• Incorrect carburetor adjustment.

When air sunses, when I operate ICE, it is necessary to check the tightness of the pipes and the integrity of the gaskets in the CPG. The problem with the circulation of the fuel mixture can be solved by the elimination of blockages in the fuel pipes leading to the carburetor. If a vacuum occurs in the tank and not receipt of the fuel mixture to the carburetor, it is enough to clean the soundtress with a thin needle and blow it with air.

The lawn mower does not develop speed.Another reason

The analogue of Husqvarnana develops the reason, the reason was very simple (watch in the video)

If you have done operations with the filter, but the work of a trimmer for grass working from gasoline remains the same, the benzotrimer does not gain momentum what to do?

Then you should try to extract the filter from the device in order to provide the so.called “relief” of the trimmer for grass. Why is a Chinese lawn mower not developing speed, the cause of Husqvarna. Should help.

The next and rather common problem when working with a gasoline trimmer is that it simply stalls and does not give any signs of life.

In this case, the problem may be as follows:

The last and most common cause of the breakdown of a gasoline trimmer for grass is that the cable that is located in the carburetor department was just sleeping.

Therefore, make sure that it will be well pulled, but not to the limit, otherwise with too much load on the gasoline trimmer for grass, this small cable can crack and then you will definitely have to contact the service center, and then also throw out many money into the wind.

A trimmer does not start for the grass for cold reasons

To begin with, we will analyze the situation when it is impossible to start the engine of the lawn mower to a cold. What does this mean? Surely Kosari came across a situation where a trimmer for grass starts on hot just perfectly, but you just have to make a short break, as the problem arises. This problem with the start of the engine after it cools. What could be the reason? Of course, no one excluded all the above factors, but if the situation is constantly found, then there is no need to check them. If a hot lawn mower starts well, and problems arise on the cold, then you should look for the reasons inside the CPH (cylinder-piston group).

To identify a malfunction, you will need to use a compressometer. We screw the compressometer into the hole instead of a candle, and after that we drive the starter handle. Measure the pressure inside the cylinder. compression. The amount of compression should be at the level of about 8-12 atmospheres. After the tool has warmed up (it is enough to work for 15-20 minutes), you should repeat the verification procedure. If the compression on the hot engine is below 8 atmospheres, then the CPH fault is appropriate. This means that the rings, the piston and the walls of the cylinder are worn out.

You can fix the situation by replacing CPG

When replacing it, it is important to take into account such a recommendation as abundant smearing of parts with motor oil inside the cylinder. This is necessary so that in the first minutes of starting a new cylinder with the piston, no formation of

With a decrease in engine compression, fuel consumption increases, and the productivity of the tool falls. You can work with such a tool, however, with each subsequent hour of work, wear increases. One day, the lawn mower will not be completely launched even with warming up.

It is interesting! You can warm up the engine of the lawn mower with low compression by pulling the starter handle. When warming up, the metal is expanded, thereby the compression increases.

Problems in electronics

In a modern car, all the processes that occur in the engine are controlled by a special computer computer. This system independently selects optimal modes and the ratio of gasoline and air in the fuel mixture.

For the mixture to be prepared correctly, the ECU collects data from a large number of sensors. So, if the car stalls when you press the gas (injector), then the throttle position sensor could fail, DMRV or coolant temperature. Determine whether sensors work correctly, you can use special diagnostic devices.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

• Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
• A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
• The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
• Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
• Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

• First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
• Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
• Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
• Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.
• If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
• After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

• completely drain the fuel;
• disassemble the lawn mower, wash and clean all available components;

• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

At high speeds

When a braid for grass stalls at high speeds, this is due to the following problems:

• clogging or clutching a valve located on the gas tank lid;
• The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
• problems with the circulation of the fuel mixture;
• atmospheric air
• The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.
• If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
• After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

Why stalls the lawn mower | Benzotrimmer | when pressing gas ? We solve this problem /al-ko FRS 4125

To store the tool in cold weather, you need:

• completely drain the fuel;
• disassemble the lawn mower, wash and clean all available components;
• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

If you stalled when heated

The lawn mower often stalls when heated. It looks like this. the tool starts, works “jerking” (not smoothly) and stalls quickly. This situation occurs due to boiling of fuel in a carburetor or incorrectly selected damper, which should not be disk, but rotary. In the latter case, if an error is detected, the part must be replaced.

The reason for heating the trimmer for the grass may be damaged ignition circuit or faulty coil. The broken node will need to be replaced with a new.

What to do if the lawn mower starts and stalls?

Now we will consider all the above problems described in more detail.

In principle, the reasons why the engine of motorcycles stops working when pressing gas can be a huge number. Here we will consider only the most common.

Perhaps the air damper just clogged. And to eliminate the problem, it will be enough to simply clean the air damper. The engine also stalls due to the clogged air filter. To clean it, the filter should first be washed in the solvent, and then blow the stream of compressed air.

A similar procedure should be carried out with the clogged fuel filter, which prevents the intake of the fuel in the proper volume with an increase in engine speed.

The engine can stall for other reasons. Firstly, the spacer is worn between the cylinder and the carburetor, and secondly, the crankshaft oil seals began to suck in air.

We have already indicated that in this case the problem is in the carburetor. In it, due to increased temperatures, gasoline begins to boil, which is why the air-fuel mixture ceases to form or its quality is critically reduced.

In addition, this problem may arise due to the fact that the carburetor is equipped with a rotary rather than a disk damper. If the problem has acquired a chronic character, then it should be solved radically. by buying a new carburetor with a disk barrier.

Most likely, access to the fuel tank is difficult or completely absent, which is why a reduced pressure zone is formed in it, due to which the engine stops receiving fuel in the required amount and because of this you stop working.

The engine at idle can stall for the following reasons:

News ONENEN ONENEN ONENY ONENY ONE ONE ONE

LSI and began to prepare not quite normal gasoline solution, which is why they began to fall on the drum;

You will need spare parts to eliminate most problems, and the Well Part will be ready to provide them with the best cost to you.

The lawn mower stall when you press the gas, how to eliminate the breakdown

The reasons why the lawn mower stalls is a huge number, we offer the most common of them, and we hope that you will find your own, and, of course, eliminate it. So, one of the situations is to clog the air damper, then the hole behind which the fuel is sprayed. If something got into it, then it can most often be quickly and easy to remove. This is the simplest reason, like a clogged filter. It needs to be washed in the solvent, and then get it well with compressed air. If it is not subject to repair, then order a new one in spare parts from the Kosikos store.

Similarly, when you press the gas, the tool stalls because the drive has clogged. The following option is possible: the fuel does not come in full, so you need to check or replace the fuel filter. To other possible reasons, the stalled motorcycles, when you give gas, should be attributed:

To all these reasons for which the mechanism stalls when adding gas, we will add several useful recommendations for the treatment of a motorcycle. First of all, before starting working with any equipment, you need to read the instructions. In this case, an important role is played by the consistency of gasoline and oil, correctly prepared by you, and also not to overheat the unit, and not leave gasoline for the winter when you simply will not use the machine.

In the full work of any tool, an important role is played by the coordinated work of all its components. And if in one it is a fishing line for a trimmer for motorcycles, then in the other a piston or carburetor. Motokos owners who want to use their tools at full power, you need to understand that the load on which the capacity of the machine is not designed may simply break the entire mechanism or its individual parts. Therefore, only competent and moderate operation involves the long.term effective work of any benchmate tool.

The trimmer stalls for grass at idle. the causes and their solutions

To common situations why a trimmer for grass or a lawn mower stalls, it should be attributed to its work at idle. Let’s immediately move on to the reasons:

• heating the gearbox and sleeping on the drum as a result of the fact that the gasoline solution is not prepared correctly. The required proportion is 1: 4;
• carburetor pollution;
• The throttle flashed;
• When opening the damper (if the experiment was carried out), the air flow makes a mixture of the “poor”;
• Ringing the carburetor;
• clogging of the air filter;

The insufficient amount of fuel that you need to work as a gas tool will entail a situation when at high speeds, with an increase. a trimmer for grass works and stalls in idle. In a situation with a carburetor. the device will stall for a cold launch and “on hot”

For any user, Motokosa. Professional and Amator, it is important to understand that any tool problem can depend on the petty flying of the part, the release of fastening or clogging, as well as on the global breakdown of the important part of the mechanism

Despite all kinds of problems, your device, nevertheless, needs such an obligatory component as knives for motorcycle, without which the exploitation of braids for grass is simply impossible!

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

When to contact the workshop

If the device is under warranty, at the first signs of incorrect operation, it can be safely attributed to a specialized workshop. Repair will be made for free, regardless of the nature of the damage, if it happened not due to the fault of the owner. In case of breakdowns in the engine, an ignorant person in technology, it is better to immediately contact a specialist. In any case, the degree of seriousness of malfunctions with the unit is determined by the user himself.

Summarize. Both gasoline and electric trimmers for grass are designed for many years of reliable work. Most of the problems described above occurs due to the insufficient attention of the owner to his assistant. Subject to strict compliance with the requirements from the manufacturer and regular maintenance, the manual mower will work rhythmically and without interruptions.

For what reason does an electric braid for STIHL grass do not develop full power

When using an electric trimmer for the grass, non.aviation problems may also occur. Here the reasons are completely different than that of fuel cos.

You can eliminate problems yourself

Eletric trimmer for grass does not develop the required power, because:

• The voltage in the network is below the required minimum for the device more than 10%;
• There was a failure on a smooth launch (if there is such a system);
• there was a malfunction of the brush node;
• The engine winding was burned;
• rotating parts sometimes jamming.

To establish voltage, you should first check its power. If it does not meet the norms, it should be increased using a stabilizer.

The repair of the smooth start system is carried out only in the service center.

With wear of brushes, you just need to replace them. When installing new ones, it is recommended to clean all the surfaces with which they contact.

To establish voltage, you should first check the power.

When burning engine windings, you need to change the electric motor.

Jamming of parts of rotation can occur for various reasons. To eliminate them, you should review the entire drive unit.

The last problem may also arise in another unit of this company. the STIHL prisoner, and the sharpening of the disk on the scissors will be its solution.