How much line to wind on the trimmer

How to properly wind the trimmer line onto the spool

Grass trimmers are indispensable helpers both in large and small summer cottages. The convenience of their use is a controversial issue, since it requires certain skills and physical training from the owner. the trimmer is hung on the shoulder using a special belt and in a few hours of work the hands can get pretty tired. But even in the process of preparing the unit for operation, difficulties may arise. For example, winding a line around a trimmer reel can be a real challenge. We will show you how to avoid this.

much, line, wind, trimmer

It often happens that fishing line is much easier to find than a ready-made reel of line. And the line will cost less than a ready-to-use bobbin. However, it is important to know a few basic rules for winding the line on a reel, which will help to avoid problems with further use.

Open the spool and carefully inspect the bobbin. you should see an arrow, it will indicate the direction in which you will need to wind the line.

Pass both ends of the fishing line into different holes and stretch to the end, and then. wind the fishing line (both ends) in one direction. an arrow will point to it.

Carefully insert the ends of the line into the spool, keeping the cord coiled. Lower the bobbin into the spool and close.

A few secrets of winding trimmer line onto a spool

To make the line break less during operation, wind less than the capacity of the reel itself. For example, if the coil capacity is 15 meters, you should wind 10 meters (that is, two ends of 5 meters, respectively).

When using a line with a figured cross-section, remember that its diameter should be at least 0.3 mm less than the “working” diameter of the trimmer. Such a discount is made so that the notches of the curly line rub less and the line does not break so quickly.

You need to wind both lines at the same time (both ends), avoiding overlaps. You will have to try and learn how to properly hold the tension of the fishing line: if you pull it, the line will overflow, if you do not pull it, it will twist. And you only need to wind the curly fishing line with gloves, otherwise you will get hurt.

Do not leave the ends too long, which is why the line often twists when cutting grass.

When mowing grass near obstacles (tree, fence, bush, fence, concrete), remember that line consumption will go much faster, since the line will cling to this obstacle. Take a bigger coil.

Installing Trimmer Line. Husqvarna Trimmer

If it is false for you to wind it alone, ask someone for help Practice shows that four-handed winding can be much more effective.

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these garden tools, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

How to wind the line on a trimmer reel: winding methods and video

Any garden owner knows how quickly weeds can fill an area. A trimmer will help to defeat them without undue effort. This incredibly useful device is an indispensable tool for trimming and mowing grass.

It is no secret that an ordinary lawn mower cannot be used everywhere. In contrast, the trimmer can handle even very difficult areas. This is especially true for those tools in which the cutting element is not a knife, but a fishing line.

Preparation for winding the line

Before the winding process, it is necessary to remove the spool with line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:

    Compact Power Trimmers.

Straight bar trimmer

This model provides the ability to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To mount the trimmer knife, it is necessary to align the hole of the reel and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the body can be easily unscrewed by hand in a clockwise direction.

Spool Trimmer Heads

The main elements of the trigger is the mowing head, which is a cylindrical body with a bobbin inserted inside. The fishing line (cord) is tucked into it. The heads differ from each other in the way of feeding and threading the cord. There are three types of heads in total:

  • Automatic. The line is then fed as the user decreases the engine speed. Automatic cord feeding is very convenient when there is a lot of work to be done. The disadvantage of such a head is the high thread consumption.
  • Semi-automatic. The use of such a head does not require the user to perform any complex manipulations. The principle of its operation is designed in such a way that the line begins to automatically lengthen while the trimmer is operating at full speed. You just need to lightly bang the head of the machine on the ground (this will remove the blocking of the line), and the cord will be pulled out of the bobbin due to centrifugal force. Then the line is cut to the required length with a knife, which is located on the protective casing.
  • Manual. To lengthen the cord, it is necessary to stop the apparatus. After that, the line will need to be pulled out manually.

Types of trimmer spools

Removing and disassembling the coil

The mowing trimmer head consists of a cover, a spring (not available in every model), a bobbin with a cord, and a cover. Before proceeding with the disassembly of the coil of the electrical unit, be sure to disconnect the trimmer from the mains. The disassembly method depends on the attachment of the mowing head. First option:

  • To remove the cover that covers the inside of the head, press on the latches (latches) that are located on both sides of the head.
  • Remove the cover, under which you will see the spool. remove it from the body. Some trimmer spools have a spring under the bobbin, which must also be carefully pulled out.
  • After removing the bobbin, you will see a screw in the center of the case. Unscrew it with a screwdriver.
  • After removing the fasteners, take the body of the part and, shaking it in different directions, remove the gearbox from the shaft.

In the second version, the trimmer head is screwed onto the gearbox shaft. To remove it, you need to fix the shaft. For this, such devices have a hole through which a thin screwdriver or metal rod is inserted. Brief instruction:

  • Insert a screwdriver into the special hole, then lock the shaft.
  • Grasp the body of the head and start twisting it. This should be done clockwise, since the thread on the shaft is left.

Winding the line to the reel

Preparation. remove and disassemble the spool

On most electric and petrol trims, you will need to remove the spool to replace the line. The FUBAG tool lets you skip this step. To make the instruction universal, we will still consider it in detail:

Secure the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod.

Unscrew the bobbin case. In our example. strictly clockwise.

Unscrew the cover according to the direction indicated on the body.

Remove the coil for winding.

The preparatory stage has been passed. You can proceed to winding the fishing line.

Which line to choose

Before you stock up on this material for refueling in the trimmer, you need to decide on the choice. After all, the usual so-called round fishing line is far from the only existing species. How to choose the most suitable one? First you need to determine the working conditions.

Selection by type. Round line is the most common. It will fit any coil with rare exceptions. This type of consumable is suitable for cutting fresh, juicy grass. But with the mowing of the so-called dead wood, such a species may no longer cope. It is pointless to mention attempts to mow bushes with this thread.

In addition to the usual type, there are others with sharp edges. Usually they are made with an asterisk or a square. The presence of sharp edges is the main feature and key difference of these threads.

It is due to this feature that threads of these types are able to mow dry weeds. But sharp-cut threads are not without drawbacks, the main of which can be called rapid wear and strength, which is noticeably inferior to the round type.

In addition to the already mentioned types of woods, there are also interesting and common varieties. Especially among them can be noted fishing lines, inside which a metal wire is stretched. This type of thread is often used in gasoline powered tools with an engine over 1.5 horsepower.

Metal-cored threads come in both round sections and sharp edges. Regardless of the type of section, such threads are the best suited for overcoming difficult-to-cut plants. Threads of this type can easily mow not only dry grass, but even small bushes.

The wires with a wire inside compare favorably with other types of consumables for their incredible wear resistance. Unfortunately, this feature has a more than noticeable impact on the price of this type. The cost of yarns with a core is much higher than the cost of other types of yarns.

Line selection

For the threading of the line into the trimmer head to be successful, it is important not to miscalculate with the choice of consumables. The thicker the cord you tuck in, the thicker and tougher the grass it will be able to cut. Often a universal line is used, the diameter of which is 2 mm. You can choose a diameter suitable for the mower in the following ways:

  • Refer to the instructions that came with the trimmer for line thickness information.
  • Pay attention to the bobbin itself. Sometimes information about the possible diameters of the fishing line is applied on it.
  • Another option is to try inserting the cord into the exit hole. If it easily goes through it, then the selected line diameter is suitable for use.

Trimmer reel

You can choose a cord thread according to the type of engine. If the line is too thick, then the resistance to rotation will increase. in this case, the engine will overheat and will soon fail. Helpful hints:

  • For an electrical device with a motor less than 500 V, a 1.3 mm thread is suitable. If you can’t find one, then you can use a 1.6 mm line. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
  • With a petrol trimmer, the shaft mower matters. For the folded version, a 2 mm cord is often used. If the shaft is straight, use a 2.4-2.5 or 3mm thread. The thickest line is installed on powerful devices. from 1.3 kW.

Pay attention to the type of section of the cord thread. Some popular options:

  • The most common round lines. They mow fresh grasses well, but they cope worse with shrubs, dead wood.
  • Twisted (spiral) cord is not very strong, but is good for thin young grass.
  • Serrated thread with sharp edges is ideal for large weeds in a neglected area.
  • You can mow your lawn more evenly with rectangular, star or square trimmer lines, but they are not very strong.
  • Strongest. two-piece inner-core round cord.

Types of trimmer line

Please note that you cannot use wire, metal strings and cables, as well as ordinary fishing thread instead of fishing line. The device will be dangerous to both the user and others. So the cable or similar products will gradually begin to work, as a result, their ends will unravel, and small pieces will scatter at high speed.

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these garden tools, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

A couple of tips

If the line was wound correctly by you, then when you press the bobbin button, the cutting element should be automatically pulled out. The line for your mowing device is one of the most important elements, without which the trimmer can lose all its functionality. You could say that the line (cutting element) is the heart of your mower. Therefore, when buying a fishing line, pay attention to its quality first. When purchasing a fishing line of a particular company, be sure to compare it with the quality of the old fishing line.

How to thread the line into the Stihl trimmer spool

The trimmer is one of the most common tools that you can use to quickly and easily cut grass, small shrubs, lawn grass and other weeds. It’s not a secret for anyone that in order for the mowing of grass to be successful, it is necessary to use the tool correctly and correctly handle individual cutting elements.

In trimmers, it doesn’t matter what fuel they use, special cutting attachments (knives, discs) are used, and some trimmers are supplied to the market in the heads of which such a cutting element as a fishing line is installed, and therefore many are wondering how to fill the line into the Stihl trimmer coil if there are no skills as such.

  • Cutting attachments in the form of knives can be sharpened, but the fishing line (also cutting elements), but tends to be consumed. Below we will talk about how to properly thread the cutting element into the Stihl trimmer spool. fishing line.

articles

Changing the line in the trimmer: 2 easy ways

A trimmer is a necessary and useful tool for a summer cottage and a private house. Many people own and actively use it, but not everyone knows how to replace the line in the trimmer, especially at first.

In this manual, we’ll walk through the entire replacement process step by step. Looking ahead, there are two ways to line the trimmer spool. There is no fundamental difference. the difference lies in the fact that in the first case one line will be refueled, folded in half, and in the second there will be two such lines.

Single-barbed trimmer spool

Single-barb lawn mowers reel

Many owners and specialists note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the trimmer reel.

After winding, you need to leave a free end of 15-30 cm to increase the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.

Method 2. two segments

Two coiled line lengths

fundamentally no different from the method The only difference is two wound pieces of fishing line, instead of one.

The end of each segment is folded

The end of each segment is folded.

Two special fixing sockets

There are two special fixing sockets on the coil (see picture above).

We start winding the line

They hook it with a hook formed earlier on the fishing line, and begin to wind the fishing line.

Winding is carried out in a special order

The winding must be carried out in the following order: first the lower line, i.e. the one that is closer to the fixing holes at the bottom of the coil, and only then the top one, i.e. the one that will overlap the bottom section.

The bottom line is reeling

The tips are cut into the holes in the trimmer spool body. They are pulled up until they click, which means that the line has come out of the latches.

The tips are threaded into the holes in the trimmer spool body

The coil is fastened into the body. The line in the spool has been replaced.

The line in the spool has been replaced

Preparation for winding the line

Before the winding process, it is necessary to remove the spool with line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:

    Compact Power Trimmers.

Straight bar trimmer

This model provides the ability to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To mount the trimmer knife, it is necessary to align the hole of the reel and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the body can be easily unscrewed by hand in a clockwise direction.

Method 1. how to properly wind the line or put it on a reel and choose the required length

To implement this method, you will need to first prepare a fishing line of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is an easy way to find out how much line you need to refuel to charge the reel. To do this, wind the rig inside the coil until it is level with the side protrusions. In this case, the rigging should not go beyond these extreme protrusions.

The thicker the equipment used, the shorter its length will be needed and vice versa, the thinner, the longer the segment will be needed.

The instruction on how to properly tuck the equipment into the trimmer or lawn mowers is as follows:

  • To begin with, a piece of fishing line that was prepared to be installed in a reel must be folded in half. In this case, one edge should protrude more than the second by 10-15 cm
  • After that, take the second end from the other side, and fold it in half. Move to it so that the measured protrusion of 15 cm is preserved
  • There is a slot in the inner baffle of the coil, into which the resulting loop should be inserted. The cut in the wall is shown in the photo below.
  • Next, we find out the direction of winding the line. If you wind the rig in the wrong direction, then it will not function correctly, and you will need to redo the work. To insert the line and wind it in the correct direction, inspect the surface of the spool. It should indicate the direction of winding (in 99% of cases, this direction is indicated). What the direction indicator on the coil looks like is shown in the photo below.
  • This arrow-shaped pointer can also have the designation, as in the example above “WIND LINE”, which means the direction of winding. If the pointer is missing on the reel, then you need to look at the head. There is a direction of its rotation on the head, and in order to properly wind the fishing line, wind it on the drum in the opposite direction to the indication of the arrow indicator. So, if the arrow is on the tip, then you need to wind in the indicated direction, and if it is not there, then you should wind against the direction of the arrow on the surface of the head
  • Having decided on the direction of rotation, you should start winding. Each end should be guided in its own groove. If there is no separator, then the equipment must be laid in the appropriate distribution order.
  • When almost all the fishing line is wound on a reel, you will need to do the following. place a short part in the hole of the side wall of the pickup, the protrusion of which should be up to 10-15 cm, and then similarly do the procedure with the other end, placing it in the hole on the parallel side
  • We insert the coil into the head, first passing the ends of the fishing line into the holes of the drum
  • We put the drum in place and, pulling the ends of the line, disengage them from the temporary clamps in the wall of the reel. After that, you can put on the cover until the latch engages.
  • At this point, the process of how to replace the fishing line on the trimmer is completed, and if necessary, you can only trim the ends (if their length does not suit), and install the assembled drum on the tool

With how to put the drum in place, no difficulties arise. There is also a second way, how to charge the mowing equipment in the lawn mower. What is the difference, and how is the second method of threading the line on the reel of lawn mowers carried out, we will find out in detail.

Method 2. how to properly put the line on the reel of lawn mowers with photo description and video

The second method differs from the first in that it is not a single piece of equipment that is charged into the coil, but segments from two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into a lawn mower’s line is the same as with the first method, and to make sure of this, below are detailed instructions:

  • There are two equal length pieces of material that you can use.
  • One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be secured
  • Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
  • The brace of the fishing line should be hooked on the bracket, and wind it in observing the direction of the arrow
  • The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
  • Manipulations with the second end of the fishing line are carried out in the same way.
  • The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the coil, the cover with the latches is installed

The above instructions on how to install a fishing line in the lawnmower will help not only correctly, but also quickly make the replacement procedure. Assembling the trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to conveniently fix the tool. Video instruction is presented below.

Step-by-step instructions on how to wind the trimmer reel and lawn mowers

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the reel. This information is usually presented on a tip, which will not allow you to make mistakes with the use of the appropriate equipment.

If there is information on the reel about the diameter of the line you can fill in, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the rig, it remains to figure out how to charge it. There are two ways to do this, but not all of them are applicable. We will consider both methods in detail, and depending on which models of lawn mowers and trimmers you use, you decide on your own which option is suitable.

How does a line head work on a lawn mower why you need to know how it works

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most drums have a pressure spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the trimmer head without a spring, i.e. on the head of the manual type. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the instructions described above.

How to change the trimmer line on a Ryobi 18 volt cordless string trimmer

The principle of operation of the semi-automatic trimmer coil is as follows:

  • Inside the head there is a coil, which is fitted on the slots, which prevent its free movement.
  • A spring acts on the coil, which presses it against the slots in the cover structure
  • A fishing line is wound on the tip, the length of which depends on the tool itself. Typically this length is between 1 and 4 meters.
  • During the performance of work, if it is necessary to increase the length of the line, the protruding part of the drum is pressed, whereby it disengages from the splines. In this case, the line is unwound from the drum, increasing in length
  • After releasing the required amount of fishing line, release the pressure and continue cutting the grass

The advantage of a tool with a line is that this consumable does not require sharpening, compared to metal discs. In addition, if a stone or a tree comes across on the way, the line simply breaks off, without adversely affecting the gearbox and engine of the tool, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to go on to consider the process of threading the line into the trimmer spool. After all, it is this moment that causes difficulties for most owners of special tools.

What you need to know about trimmer line

A fishing line is a consumable made of nylon that serves as a cutting device. By means of this equipment, the grass is cut, which is ensured by rotating the tool head at a high frequency. This material has a different thickness, which depends on its use on the corresponding tools, low-power electric (from 1 to 1.6 mm), electric from 500 W (2 to 2.4 mm) and gasoline trimmers with lawn mowers (from 2.4 to 3. 2 mm).

The more powerful the tool, the correspondingly thicker the cutting equipment should be. This affects not only the quality of the grass cut, but also the service life of the material. If you are wondering how to wind the trimmer coil, then it is time to change and reload the tool. With the onset of spring, this question is becoming more and more popular, so it’s time to figure out the step-by-step instructions for replacing the line in the trimmer reel.

Learning to properly wind the line on the trimmer reel and lawn mowers installation instructions

Private home owners know how essential a trimmer tool is. It can be gasoline and electric, and they differ in the design of power units. For cutting grass in areas where there are stones, trees and other obstructing objects, a fishing line is used as a cutting device. This consumable wears out during use, so how to wind the trimmer coil, we will consider in detail in the material.

How to remove the spool from the trimmer and remove the line

Initially, remove the line from the trimmer spool before threading it into the trimmer spool. A reel or aiming device is a device that sits inside the mowing head, bobbin or drum. There are different types of heads (depending on the manufacturer), but the principle of replacing the line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it.

The instruction on how to unscrew the manual head on the trimmer is as follows:

  • Turn the tool upside down and, if necessary, clean it from dirt. With two fingers of one hand, grip the cover latches (on the mowing head), which are symmetrically positioned to each other. After lightly pressing them inward, remove the protective cover from the drum
  • Next, remove the line spool from the drum shaft. It is mounted on a shaft without fasteners, therefore it can be removed with one hand.
  • The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with an appropriate tip or bit
  • To unscrew it, hold the drum base with one hand, and unscrew it counterclockwise with a screwdriver with the other.
  • After that, you can start dismantling. To do this, you do not need to pull it with all your strength, but by slightly shaking it to the sides, slowly disengage it from the metal shaft on which the drum is seated.
  • When reinstalling, fit the head into the square slots

This process is not difficult, and as you know, there is no need to dismantle the entire head if you know how the replacement is performed. When dismantling, consider the following nuances:

  • It is recommended to remove the head periodically to prevent corrosion of the threaded connection. If you never unscrew the screw, then if necessary, it will be difficult and even impossible to do this.
  • If the screw has a four-sided bore of the head, then for unscrewing it is necessary to select a screwdriver or bits of a suitable size in order to exclude the licking of the edges on the head
  • When assembling the unit, treat the threaded seat with lubricants, for example, grease or machine oil.
  • If the edges on the screw are licked, then special clamping pliers can be used to unscrew it.
  • There are drums that do not require preliminary disassembly. To dismantle them, grab it and rotate in the opposite direction of the clockwise direction

Knowing how to disassemble the drum, you should continue to figure out how to replace the trimmer line. The video below shows a detailed process on how to open the trimmer coil and disassemble it.

Tips and tricks on how to wind the line and what you need to know

There are some useful tips and tricks that will be useful to learn not only for beginners, but also for experienced mowers. These tips will help prevent negative consequences in the form of injury and malfunctioning of the mechanism. These guidelines read as follows:

  • It is necessary to install the cover until it clicks. over, this is 2 or more clicks, which depends on the number of latches. If one of the latch does not snap into place, the drum may jump out when starting the tool and injure a person.
  • Do not reel in the line with a strong pull, or more than you can insert it into place. It is better not to wind up the rig than there will be more of it, as this will lead to negative consequences in the form of the impossibility of unwinding it if necessary
  • If you own a tool not with two line leads, but with one (usually these are low-power units), then the winding process is performed in a similar sequence, as described above, only with the difference in the absence of a middle rim between the extreme bases of the coil
  • After replacing the material, it is necessary to first check the operability of the tool, and after that start mowing the grass. If you do not make a preliminary check, then the scaffolding can unwind and injure a person.

The result of the work done is as follows. after the replacement of the new material, the usual one is enough for an area of ​​up to 600 square meters, but taking into account the presence of a reinforcing layer on the fishing line. Conventional nylon materials last less, which is important to consider when working. Do not try to cut thick-stemmed grass with fishing line, as there are special metal discs or knives for this.