How to assemble cutters on a bright 105 walk-behind tractor

How to assemble cutters for a walk-behind tractor

How to assemble cutters for a walk-behind tractor and a motor-cultivator

Motoblocks and cultivators from Aurora, and in principle, like many other manufacturers, are supplied with cutters disassembled. Often, for owners of new equipment, the process of assembling mills becomes a problem. In this article, we will describe how to assemble working cutters from the details of this “constructor”. For the Aurora technique, depending on the model, the cutters are produced on axes in two sizes. Axle diameter for light vehicles is 23 mm, and for heavy vehicles 32 mm.

Cutters for light motoblocks and cultivators are easy to assemble. To do this, it is necessary to install the blades in special mounting slots and fasten them with bolts. Pay attention to the direction of the blade cutting edge. It should look in the direction of movement of the walk-behind tractor. In addition, each blade is marked. If the letter quotRquot is indicated, it means it is turned to the right, respectively, quotLquot is to the left.

Each next section is fixed with the previous one by means of a pin, and is blocked with a pin. The cutting disc must be secured with a bolt. Depending on the power of the technique, the number of cutters will be different. Their number can be 24, 32 or 40.

BCS Mowing Sulky attachment assembly and review – RMM0072

The number of blades can also differ and can be three or four per section. This is due to the number of mounting plates on the axle. If the axis of the cutter is straight, without offset relative to each other, then the number of blades will be three. For offset models. four.

Four-blade cutters are assembled sequentially, one left, one right. It will be easier to assemble the cutters if at the very beginning you divide the left and right blades into two parts, for the left and right cutters.

Three-bladed are assembled differently. The first blade is installed on the axle and fixed with a bolt. In the future, this bolt will have to be removed in order to fix the other blade. If the first one was installed outside the plate, then the remaining two must be mounted from the inside of the mounting plate. For three-blade cutters, the markings “L” and “R” are set separately for each side.

Cutters. How to assemble correctly? Motoblock Hopper 900MQ

Short tips and tricks for assembling milling cutters of a hopper 900 mq walk-behind tractor. With properly assembled milling cutters, the motob.

HOW TO ASSEMBLE A MOTOR BLOCK MILLER? INSTRUCTION BY OWN HANDS

Instructions for assembling a cutter for a walk-behind tractor. It is very important to correctly assemble the cutter, with the correct assembly of the cutter.

How to assemble a router bit to make it work ?

SUBSCRIBE! useful videos for TRACTORIST are coming soon ️ In the video we will show the assembly of active soil.

Vpiska and Friendzone: Maibie Baby’s orientation, who from the group wrote Doradura, Valera’s departure

How to assemble a milling cutter on a walk-behind tractor

You can buy a walk-behind tractor here: https://agrosad.com.ua/catalog/motobloki A large number of buyers of new agricultural machinery ask.

assembly of an active cutter: a motor-tractor; walk-behind tractor; mini tractor!

subscribe don’t miss new and interesting videos))) also follow the link where you can purchase such.

MILLS FOR MOTORBLOCK. OVERVIEW AND THEIR ASSEMBLY

This video describes in detail about milling cutters for a walk-behind tractor. You will learn about what cutters are. How to distinguish.

how to assemble cutters on a walk-behind tractor

How to assemble cutters on the Neva walk-behind tractor

Hello everyone, the channel with their own hands presents an opportunity to see firsthand how I collected cutters for the Neva walk-behind tractor.
In principle, there is nothing complicated about the assembly of cutters, but all the same for those who have a little doubt it will be useful to watch this video. Enjoy watching.

I would like to remind you that every full viewing of advertising is aimed at maintaining this channel, it is not difficult for you, we are pleased.
And yes, I almost forgot, do not forget to subscribe to the channel With your own hands on YouTube and in contact. By the way, who is signed in the contact will participate in the competition, the group is called: Do it yourself. Useful video for men.
=
All the greetings of the channel with their own hands represents the opportunity to see first hand how I milled cutters for the motor-block Neva.
In principle, there is nothing complicated, in the assembly of mills, but still for those who have little doubt it will be useful to watch this video.

I wish to remind you that each full viewing of advertising is to maintain this channel you will not difficult, we are pleased.
And yes I almost forgot do not forget to subscribe to the channel own hands on YouTube and in touch. By the way who is signed in contact will participate in the competition group is called: The hands. Useful video for men.
=
in contact with:
=
Music:
1. Vacation Uke
2. Beat Your Competition
3. The composition All Good In The Wood belongs to the performer Audionautix. License: Creative Commons Attribution (
Executor:

=
To improve the channel, I will accept any help as a voluntary donation in favor of new equipment for filming, therefore, no contracts are envisaged.

Webmoney: R997081599203
Yandex money: 410012791967875
thank

HOW TO ASSEMBLY THE MOTOR BLOCK MILLER CORRECTLY? Not everyone does this! Will work even on virgin soil?

It’s easy to assemble a milling cutter for a walk-behind tractor.
Do this and the cutter will work even on virgin soil.
We compare the capabilities of milling cutters of various motoblocks, the width and depth of cultivation, the shape of the knives.

How to assemble a milling cutter for a light walk-behind tractor! Youtube channel “Yurii81 Vorobiov”

My Youtube channel:

MILLS for motoblocks 105/135. Fixing factory errors.

My YouTube channel:
My page on Odnoklassniki:
My VK page:
My VK group:
MY
MILLING the soil with the hopper walk-behind tractor
Cultivation of soil under a steam diesel walk-behind tractor HOPER 1100 9DS MQ
Modifications of the diesel motoblock HOPER 1100 9DS MQ
Diesel walk-behind tractor HOPER 1100 9DS MQ Replacement of hitch bolts
Sowing alfalfa with barley. To help walk-behind tractor!
Trays for milling cutters of a walk-behind tractor
Test of self-made plates for milling cutters of a walk-behind tractor

MILLS ON MOTORBLOCK. OVERVIEW AND THEIR ASSEMBLY

How to assemble a milling cutter on a walk-behind tractor

You can buy a walk-behind tractor here:
A large number of buyers of new agricultural machinery ask how to assemble cutters for a walk-behind tractor or a motor-cultivator. Today we present a video instruction for assembling a rotary tiller.
The tiller of the walk-behind tractor and the motor-cultivator allows for cultivation. The width of the tiller depends on the type of equipment and engine power. Usually, the milling cutters of the walk-behind tractor are type-setting.
We are sure that this instruction for assembling a cutter for motoblocks KENTAVR, ZUBR, FORTE, WEIMA, BULAT, DTZ, ZIRKA, Iron Angel will help you.

How to assemble a milling cutter for a light walk-behind tractor!

Assembling the milling cutter of the walk-behind tractor.

Nothing superfluous: only assembly of cutters for a walk-behind tractor and a motor-cultivator

Watch the video instruction on how to assemble the cutters on the walk-behind tractor. The permanent technical expert of TMK reveals the tricks of assembling cutters on a walk-behind tractor, and also clearly demonstrates the process. The video shows the assembly diagrams of cutters for the right and left semiaxis. Oleg Bazlov shows how to determine the direction of the cutter and correctly install the parts on each of the axes. Find out the features of assembling a cutter on a walk-behind tractor in our video! Links to the tool in the review:
Motoblocks:
Motor-cultivators: We are in social networks:

HOW IT IS CORRECT TO ASSEMBLE THE MILL ON MOTOBLOKKENTAVRMB 2013B-3

# assembly milling cutter # Ukraine # Oleksandr Krivolap This is not an advertisement, this is our rural life. I share my experience in assembling a cutter for a walk-behind tractor KENTAVRMB 2013B-3, Before assembling a cutter for a walk-behind tractor, I studied the instructions for a walk-behind tractor KENTAVRMB 2013B-3. assemblies correct and incorrect and it is difficult to choose the right one, but the instructions for the walk-behind tractor are written clearly and understandably. HOW CORRECTLY TO ASSEMBLE THE MILL ON THE MOTOBLOCKKENTAVRMB 2013B-3. The left one I assembled, but I was wrong a little bit wrong. I will shoot a video on assembling the left cutter and pour it on the channel the other day. If anyone was helped by my video on assembling the cutter, I will be very glad. GOOD LUCK TO YOU FRIENDS.

How to assemble cutters on a walk-behind tractor

How to assemble cutters on a walk-behind tractor.

An improperly assembled set of cutters will greatly slow down the work or even make the work ineffective. This video will teach you how to properly assemble cutters for walk-behind tractors and cultivators (using the example of a set for the Patriot Pobeda walk-behind tractor).

Follow the news on social networks:

# MotoblokAgat #assembly of cutters #mills for a motorblock

Hello everyone! In this video, I will show you several ways to assemble cutters. I’ll tell you how not to assemble and show why these assembly methods are wrong. And of course I will show you how to properly assemble the cutters. Thanks for watching. Stay with me and there will be many more interesting things to come.

How to assemble a milling cutter for a walk-behind tractor with three-knife sections without errors

In this video, my son and I will assemble a milling cutter for a walk-behind tractor with three-knife sections, the most common way.

Collect milling cutters for a walk-behind tractor

And you correctly assembled the cutters for the walk-behind tractor?

How to assemble cutters correctly

Hello everyone today I will show and tell you how to properly assemble cutters for a walk-behind tractor, what are the nuances and what you need to pay attention to.
ALL PLEASANT VIEWING.
My VK
Motoblock:
Homemade quadric:
Renault kaptur:
Mini tractor 4×4:

# cutters # walk-behind tractor # garage # review # veima # niva # hopper # grousers # how to assemble a mill # cutter # garage48 # Bykhanov # Garage54 # homemade products # usman48

how to assemble cutters on a walk-behind tractor

Write any questions. on WhatsApp. 996555550533

Milling cutter assembly for FM 643, FM 653

How to assemble the cutters? Correctly assembled cutter video for the cultivator Tatra Garden HT 100, HT 80, HT 68

MILLS ON MOTORBLOCK. ASSEMBLY FOR 4 KNIVES

When buying a walk-behind tractor, many people start having problems with plowing the land. The MOTORBLOCK, then digs holes in place, then OPENING WITH MILLS goes, but not as deep as planned. How is it right to SMOOTH ON MILLS. We suggest you figure it out. Initially, the MOTOR BLOCK AND MILLS are disassembled. Therefore, there are times when the INCORRECT ASSEMBLY OF MILLS will not allow you to RUN the GARDEN correctly. By watching our next video, you will learn HOW TO ASSEMBLE THE MILLS ON THE MOTORBLOCK HOW TO SMOOTH ON THE MILLS? In the beginning, you need to figure out which cutters you have in the kit, most often there are saber-type knives. however, there are also goose feet cutters. CUTTERING will get you started with weed control. MILLING THE GARDEN is possible and necessary only with a properly selected walk-behind tractor. Knowing what kind of soil on the site you can start POWING THE GARDEN.
HOW TO SMOOTH WITH A MOTORBLOCK ON MILLS? Everything is extremely simple, you just need to assemble them correctly and install them on the # walk-behind tractor. SMOOTHING ON MILLERS will help fight weeds. After work, your GARDEN is clean and the cutters also need to be cleaned of soil, grass and clay. Only the right tool will make it easy to SMOOTH WITH A CULTIVATOR.
In our video we will answer your questions: HOW TO POLL WITH A CULTIVATOR, HOW TO POLL WITH MILLS, and yes, to the question, HOW TO PILL A MOTORBLOCK. All questions are important, necessary and we hope you will find answers to them in our videos.

This video shows the assembly of 4-knife cutters. What cutters are available and assembly for 3 knives, you can see in the video by clicking on the link

Secrets of assembling soil mills, cultivator, walk-behind tractor

Without knowing the secrets and not having experience, 99 out of 100 beginners will assemble cutters as we will show. Assembly of soil mills with 3 sections of 3 knives each. We assemble according to the factory instructions: For example, the Brado BD-850 cultivator cutters. # Milling cutters # Mounted # BradoBd850 # Cultivator # Motor-block # Motor-cultivator
–
Alteration of this configuration to the correct one:
Motor-cultivator Brado BD-850:

How to assemble a milling cutter for a walk-behind tractor

How to properly assemble and set up a milling cutter for a heavy walk-behind tractor.
Do-it-yourself motoblock and attachments:

How to assemble soil milling cultivators on the NEVA walk-behind tractor

This video. This is an instruction for the correct assembly of soil milling cutters (cultivators) on the NEVA walk-behind tractor. This process is quite simple, but for someone this video will be very, very useful.

How to assemble cutters on a cultivator

Cutters. How to assemble correctly? Motoblock Hopper 900MQ

Short tips and tricks for assembling milling cutters of a hopper 900 mq walk-behind tractor. With correctly assembled cutters, the walk-behind tractor cuts smoothly and the minimum load on the arms and the walk-behind tractor.
We mill effortlessly
And even a girl copes with milling the soil

# Motoblock # AssemblingMills #MotorblockMills

How to assemble cutters on a walk-behind tractor.

Assembling the cultivator cutters.

Why is the walk-behind tractor jumping. Correct assembly of the cutter

Correct assembly of cutters not only makes the walk-behind tractor work smooth and comfortable, it also prolongs the life of the walk-behind tractor, reducing shock loads. Shock loads are harmful to both the motor and the gearbox. they break bushings and bearings, eat up the teeth of the gearbox gears, and the body of the person driving the walk-behind tractor has a hard time. In this video I will show you how to assemble the cutter correctly, as well as what to do if correct assembly is not possible due to the incorrect assembly of the cutter. Enjoy watching!
A video about assembling and testing a walk-behind tractor can be viewed by clicking on the links in the tips in the video clip (in the upper right corner of the screen) or by clicking on the screensavers at the end of the video.

DIESEL MOTORBLOCK CENTAUR 10 HP | ASSEMBLY OF THE MILL TO A HEAVY MOTOR BLOCK. MILL CENTAUR 110

My walk-behind tractor:
Kentavr MB 1010DE-6
Weight 292 kg
Engine displacement 7.41 kW (10)
Max fuel consumption l / g 1,800
Engine starting system (manual and electric starter)

Also thanks to the guys who subscribed to the channel and support me with good comments and advice. without you this channel and these videos would not exist. THANK YOU SO MUCH.
. US 1000.10.01.2020
. US 2000.

Also my main projects. ️
✓Adapter for walk-behind tractor.
✓ Extra weight.
✓ Shovel blade.

welcome to my channel. I want to write right away that first of all I shoot the video not for instruction and criticism, but purely for myself, and who is interested in something, see.
On this channel, I will post a video about the Centaur walk-behind tractor and everything related to it (my impression, the work of the walk-behind tractor, improvements, rides on the walk-behind tractor, work from attachments and much more) so if you are interested, subscribe to the channel.

Help for new projects.
WebMoney
✓R336377888391
✓Z457434229877
✓U377083783115

# Motoblock # Centaur #Kentavr # KentavrUA92 # YuriNazarenko

How to properly assemble cutters for a walk-behind tractor.

The video shows how to properly assemble cutters for a walk-behind tractor, a motor-cultivator. Correct assembly of cutters guarantees long-term and trouble-free operation of the walk-behind tractor in your garden. Assemble the cutters correctly!

Collected cutters for the Forte 1050 walk-behind tractor

How to assemble cutters for a walk-behind tractor

How to assemble cutters for a walk-behind tractor

Cutters for the walk-behind tractor. Reassembled differently.

I looked closely and realized that I had assembled the knives of the cutters incorrectly. Now, I hope I put it together correctly. If you have any comments, write. I read all comments.

How to assemble cutters on a walk-behind tractor and a cultivator?

Up-to-date reviews of building tools, gardening techniques.

☞ Machines.
☞ Garden equipment.
☞ Power tool.
☞ Power engineering.

Subscribe and stay updated.

Surely in your free time you like to relax in nature? And even with a fishing rod!

# garden # tool # technique

Motoblock Bright M105A How to assemble three-knife cutters for a walk-behind tractor

ASSEMBLING HEAVY MOTOR UNIT ACTIVE MILL

How to put knives on a cutter for a walk-behind tractor 8 knives

Correct assembly of a new milling cutter for a walk-behind tractor

How to assemble cutters on a walk-behind tractor ron angel gt90m3 favorite

How to assemble cutters for a walk-behind tractor iron angel gt90 favorite. PRICE MAY DROP WE ARE TRADING CALL SITE. information can be found on the website. We are always glad to our customers. We deliver across Ukraine. Our warehouse is located in the city of Kiev. Company Electromotor Kiev. Contact phone 5000888

Assembling the motoblock Ant-4. How to assemble cutters on a walk-behind tractor, how to install wheels, steering wheel and controls.

Oleg Bazlov presents detailed instructions for assembling a motor-cultivator and milling cutters for the Muravei-4 walk-behind tractor at a reduced speed. The TMK technician shows and tells what is included in the delivery set, and also demonstrates all the stages of installing the walk-behind tractor parts and assembling the cutters with your own hands. In the video instructions, you can see how to properly assemble the cutter knives on the walk-behind tractor and install the right and left shaft on the equipment. Watch the video for a step-by-step guide, links to the tool in the review:
Motoblock with reduced speed Ant-4:
5% discount on the tool presented in the video with a promotional code. Ant-5We are in social networks:

How to assemble a milling cutter for a walk-behind tractor, laughter and sin.

How to assemble a milling cutter for a walk-behind tractor, laughter and sin

HOW to correctly assemble milling cutters of a walk-behind tractor / ASSEMBLY OF CHEVRON / on the example of Centaur MB 2060D

Where to see the MOTOBLOCK
A sequel on the work of cutters has already been released
Is it a joke, correctly assemble the milling cutters of the walk-behind tractor? In general, there is no difficulty here, but many people are confused by this question. Where to start assembling cutters, what types and types of assembly? And there are also many nuances about assembling a chevron cutter. I talk about all this in this video.
And this is the first part, how it all began

How to assemble a milling cutter for a WEIMA WM900M-3 walk-behind tractor

It is not difficult to install the cutter on the walk-behind tractor, but for this you have to first assemble it, having correctly organized the direction of rotation: the sharpened part should cut into the soil.

Assembling milling cutters brait walk-behind tractor

Changfu Brand Two Wheel Walking Tractor Assembling

Assembling milling cutters for a walk-behind tractor

How to assemble a cultivator on an Oka walk-behind tractor

A training video on how to assemble a cultivator for an Oka walk-behind tractor with your own hands

Wrenches for fastening nuts and bolts
Washers
Cultivator cutter
Nuts and bolts

How to assemble cutters for a walk-behind tractor

A large number of buyers of new agricultural machinery ask how to assemble cutters for a walk-behind tractor or a motor-cultivator. Today we present a video instruction for assembling a rotary tiller.
The tiller of the walk-behind tractor and the motor-cultivator allows for cultivation. The width of the tiller depends on the type of equipment and engine power. Usually, the milling cutters of the walk-behind tractor are type-setting.
We are sure that this instruction for assembling the cutter for motoblocks KENTAVR, ZUBR, FORTE, WEIMA,

Assembling milling cutters for the Shtenli 1900 pro walk-behind tractor

Assembling milling cutters of a walk-behind tractor. Preparing the walk-behind tractor for the season

Today we will assemble an additional set of cutters for the walk-behind tractor, talk about the quality of the purchase and get ready for the season. Sowing on the nose, life in the village requires you to do everything on time, then you will have a lot of free time for rest))) Vidio is more for beginners in the operation of the walk-behind tractor, I ask the old people not to throw slippers, but it is better if you said something wrong or missed, correct it me in the comments under the video)))
So much for rural everyday life, everything needs to be done in time for the season))) Otherwise, nothing, cultivation is on the nose)))

# walk-behind tractor # cutters # cultivation

Instagram:
support channel:

Friends, if you think that the author is worthy of your attention, you can support the channel with a ruble, for this the author will thank you in the next video.

HOW TO ASSEMBLE A MOTOR BLOCK MILLER? INSTRUCTION BY OWN HANDS

Instructions for assembling a cutter for a walk-behind tractor. It is very important to correctly assemble the cutter, with the correct assembly of the cutter, you reduce the load on the gearbox, your walk-behind tractor runs smoothly and smoothly, and the quality of plowing is also improved 2 times!
This cutter is suitable for air motoblocks and cultivators Centaur, Zubr, Forte, DTZ and others.

Call: 066-66-777-12 067-652-51-71

Before assembling the cutter, you need to unfold the knives into left and right
2. Which side of the cutter will cling to the hub of the walk-behind tractor
3. Determine which cutter will be left and which will be right

Assembling the first section
2. Along the guide, collect the remaining sections
3. Collect the next knives so that they repeat the direction of the knives of the previous section
4. Checking the correct assembly of the direction of the knives
5. Copying the assembly of the remaining knives
6. Assembling the left section. according to the same principle as the right
7. Copy the direction of the knives on the right section
8. Checking the correct assembly of the knives

HOW IT IS CORRECT TO ASSEMBLE THE LEFT MILL ON THE MOTORBLOCK CENTAVR MB 2013B-3

#assembly milling cutter # assembly of the left milling cutter # milling cutter # THIS IS NOT AN ADVERTISING SHARE YOUR EXPERIENCE,
As I promised to shoot a video on ASSEMBLING THE LEFT SIDE OF THE ACTIVE MILL ON THE MOTORBLOCK KENTAVR MB 2013B-3. I share my experience in assembling the Mills on the motoblock KENTAVRMB 2013B-3, There are many different assemblies of correct and incorrect ones on the Internet and it is difficult to choose the right one, but the instructions for the walk-behind tractor are written clearly and understandably. HOW CORRECTLY TO ASSEMBLE THE MILL ON THE MOTOBLOCKENTAVRMB 2013B-3. in the direction of travel.If anyone was helped by my video on assembling the cutter, I will be very happy. GOOD LUCK TO YOU FRIENDS

How to assemble cutters on a walk-behind tractor Bright BRAIT BR 105 Three-knife cutters for a walk-behind tractor Buy in Krasnoyarsk

How to assemble cutters on a walk-behind tractor Bright BRAIT BR 105 Three-knife cutters for a walk-behind tractor Buy in Krasnoyarsk

HOW TO ASSEMBLY CORRECT BUTTERS ON / FOR A MOTORBLOCK.

Why does the walk-behind tractor lead to the side? Why is the walk-behind tractor buried? ATTENTION. SPIRAL.

It is very easy to help the channel:
➥ Subscribe to the Malaya Mechanization channel
➥ Put it on. or. under this video.
➥ Write a comment under this video.
➥ Send this video to your friends via social networks.
➥ Watch the rest of the videos on the Small Mechanization channel
thank.
# Motoblock # Milling cutter # Milling cuttersFor Motoblock

How to assemble cutters for SK-1400 and SK-1600 cultivators

In this video, we tried to show how to correctly assemble cutters for the new models of SK-1400 and SK-1600 motor cultivators.

If you find this video useful. LIKE!

Contact phones: MTS (033) 633-26-26. Velcom (029) 125-26-26.

Our partner Oleg Nesterov:

How to properly assemble cutters on a walk-behind tractor! Drawing for screenshot!

Recheck your cutters according to the scheme given by the manufacturer!

Active cutters

The active milling cutter consists of a set of four powerful blades set at 90 ° to each other. There can be from two or more such sets on one axis. The number of additional cutters, as well as the size of their knives, depends directly on the performance of the walk-behind tractor. The knives of this cutter are in the form of curved strips, bent alternately in different directions. Their design and strength allow you to safely handle virgin soil, as well as areas where stones and roots come across.

How to properly assemble cutters on a walk-behind tractor?

Assembling the cutter can be difficult, especially if you do it for the first time and alone.

First, you should familiarize yourself with the structure of the cutter.

The drawing below shows its main constituent elements:

• rotor axle (it can be of different lengths, it can be one-piece and split);
• pin with a retainer;
• knives (right and left);
• structural fasteners (nuts, washers and bolts).

Also, do not forget to take into account the fact that the movement of the knives during operation is directed counterclockwise. Be careful when assembling the module. any deviation in the design will lead to the fact that the balance of the axis will be violated, the unit will skid to the side during operation.

We also offer you to watch the video, which tells in detail about the process of assembling cutters for the walk-behind tractor:

Installing cutters on a walk-behind tractor

It is better to install the cutters on the walk-behind tractor with a partner to avoid injury, fall or damage to the unit. Lift the walk-behind tractor before starting the installation. You can use the tools at hand as a support. If there are no such objects nearby, knock down two boards crosswise in the middle. Support the steering wheel with the resulting structure. Make sure the walk-behind tractor is secure. After that, you can remove the wheels and install cutters in their place.

Milling cutters for a walk-behind tractor: selection, operation, self-production

A milling cutter for a walk-behind tractor is one of the most common types of additional equipment for tillage. It is a set of special knives fixed on an axis. With their help, you can quickly and easily get rid of weeds, cultivate the soil on the site. In order to choose the optimal type of cutter for your walk-behind tractor, you should classify them a little.

Crow’s feet

The second constructive type of cutters is crow’s feet. The product got its name for the unusual shape of the cutting elements, reminiscent of the legs of a goose. They are triangular in shape and are located at the edges of the posts. The number of cutting elements and the size of this module also depends on the power of the walk-behind tractor. The more racks with knives. the better the processing.

This cutter is capable of processing heavy virgin and clayey soils, but in areas with increased vegetation and roots, the product is likely to clog.

Homemade milling cutters for a walk-behind tractor

In order to create a milling cutter for a walk-behind tractor with your own hands, you need to stock up on such tools and blanks:

• metal pipe (no more than 42 mm in diameter);
• blanks for cutting elements of the cutter (any unnecessary parts or pieces of metal will do. For example, you can use old car springs);
• welding;
• Bulgarian.

The cutting elements are adjusted to the required dimensions and sharpened if necessary. Then they need to be welded to the pipe in the appropriate order.

Experts recommend not to manufacture cutters with a diameter of more than 50 cm, as this will reduce the risk of breakage during operation. Below is a detailed drawing for making a crow’s feet cutter:

When using cutters, do not forget about safety precautions and rules for using the product. Before starting, the cutters must be above the surface of the ground, and their immersion in the soil must be slow and smooth.

Classification of cutters

According to the location of the cutters there are side and mounted. The side ones are installed on both sides of the walk-behind tractor, they work from the drive shafts of the wheels. In fact, with a similar arrangement, these cutters replace the wheels and set the equipment in motion.

The second type is a power take-off cutter located at the rear of the unit and does not participate in the movement. Motoblocks of the brands Celina, Neva MB-1 and MB-2, MTZ have just such a cutter device.

According to the design of knives, two types of cutters are distinguished. saber-shaped (active, standard) and the so-called crow’s feet.

How to assemble correctly cutters on a walk-behind tractor. manufacturing saber equipment

Immediately before the manufacture of saber-shaped rotor devices, we advise you to study the drawings that will tell you the correct procedure for assembling the equipment.

Any saber cutter for a walk-behind tractor consists of two interconnected blocks, each of which contains 12 cutters. The design of one separate unit includes 3 units, each of which is equipped with 4 cutting knives. The latter, in turn, are located in relation to 30 ° in relation to each other. The assembly of saber-shaped devices is as follows:

• First, make a stand using a 6.3 × 4 cm corner;
• Weld one of the ends of the rack to the flange so that later you can combine 4 cutting knives with each other;
• Connect all cutting elements of the cutter to each other by means of flanges and bolts with washers.

A rotary milling cutter manufactured in this way has high strength and stability, which will allow you to use it for processing soils of any density.

Which cutters are better for a walk-behind tractor. we decide on the choice

Many novice farmers find it quite difficult to decide on the right cutters for the job. In fact, there is nothing difficult about this. you just need to study and compare the qualities and characteristics of different types of equipment. The cutters available on the market are divided into 2 types:

• saber cutters. devices of this type are in the highest demand, it is these cutters that are included in the delivery set of many walk-behind tractors. Among the main reasons for the popularity of mills of this type should be highlighted the highest efficiency, the ability to cultivate any soil, including that previously untouched by agricultural machinery. High-quality models of saber cutters are made in 2 stages: first, products of increased strength are formed from carbon steel. At the next stage of production, knives are subject to prolonged heat treatment under the influence of high-frequency currents. The main feature of high-quality saber-shaped devices is the impossibility of welding cutting surfaces;
• cutters “crow’s feet”. equipment of this type appeared on the market relatively recently. In practice, hard soil lends itself to processing with such devices. free of hard weeds. The high efficiency of these cutters is achieved due to their specific shape. The latter also allows you not to harm the roots of the planted plants during the cultivation of the garden. Among the main disadvantages of this kind of devices, one should highlight their low strength and a lot of inconveniences during repair.

When buying any of these types of cutters, be sure to consider the type of soil to be processed before and after planting.

Self-installation of cutters on a walk-behind tractor

Self-installation of equipment on a walk-behind tractor is performed in exactly the same way, both for saber cutters and for devices such as “crow’s feet”.

In any case, the procedure is as follows:

• Place the manufactured cutters on a special wooden “goat”, about 0.5 m high;
• Gently tilt the walk-behind tractor at an angle of 45 °, and rest it on the opener;
• Place the “tragus” under the handlebar grip of the walk-behind tractor;
• Dismantle the standard wheels of the agricultural machine, and install homemade cutters instead;
• At the left and right outer ends of the cutters, securely fasten the discs for the cutters. they will significantly improve the movement of the walk-behind tractor with cutters and make it smoother and more stable.

After completing all the above steps, you can start processing the soil. During work, do not forget to monitor the reliability of the fastening of the plates, fixing the main and additional cutters on the walk-behind tractor.

Homemade milling cutters for a walk-behind tractor. the procedure for manufacturing equipment

The simple design of milling cutters for walk-behind tractors allows you to make such devices with your own hands. Below we will consider the correct procedure for the manufacture of different types of equipment for plowing the soil.

Production of crow’s feet cutters

Immediately before assembling this type of fixture, you will need to carefully prepare for work. With tools and materials you will need:

• steel pipe, 4.2 cm in diameter;
• steel plates for making cutting knives;
• welding machine;
• grinder with a set of discs.

The active crow’s feet cutter is assembled in the following order:

• For the manufacture of cutting elements, you can use the springs from the car. Cut them into equal pieces, and then weld them to a steel pipe that plays the role of a base;
• Sharpen the edges of the cutting elements and weld them to the base used;
• After assembling the equipment, start it and make the necessary settings. At the same time, keep in mind that after starting the walk-behind tractor, the equipment knives should hang in the air, and not touch the ground.

In order for the crow’s feet cutter to last as long as possible, it must be slowly lowered to the ground. Otherwise, the equipment may break.

Cutters for walk-behind tractor

Milling cutters are one of the most commonly used types of equipment for motoblocks. It is quite difficult to overestimate the role of milling cutters in agriculture, because these devices allow you to process the soil with high quality and fully prepare it for further planting with a minimum amount of time from the efforts of the farmer.

Do I need to sharpen cutters on a walk-behind tractor. we figure it out together

It is rather difficult to give an unambiguous answer to this question due to several factors. Firstly, the recommendations of the milling cutter manufacturer are of great importance. Some companies that make high quality plowing equipment do not advise sharpening cutting elements, as this will degrade the efficiency of the cutters and void the warranty for their service. Other manufacturers, on the contrary, recommend that you definitely sharpen the cutters before each season of operation of the walk-behind tractor.

The second important factor is the result that the sharpening of the cutters can bring. The only, but very important advantage that this procedure gives is ease in the cultivation process, because it will be much easier for sharpened cutting knives to go deep into the ground and plow it efficiently. The disadvantages of sharpening include the need to dismantle and install equipment on a walk-behind tractor every time. Another very important drawback is the ability of cutters to grind weed roots deeply hidden in the ground, which will lead to their intensive vegetative reproduction throughout the entire area of ​​the garden.

The third factor is the type of soil being cultivated. If a rotary tiller on a walk-behind tractor is used mainly for the processing of hard clay soils and virgin lands, then sharpening the cutting knives will help to plow such soil faster and better. If the soil in the garden is soft, then, as a rule, it is not necessary to sharpen the used set of cutters.

All of the above advice on the manufacture, installation and sharpening of devices are suitable for the operation of equipment in tandem with Neva MB-1, MB-2 walk-behind tractors, as well as agricultural machines of the MTZ, Celina brands and units of other imported and domestic manufacturers.