How to assemble the single -based Huter tractor.

24th March 2023

Huter GMC-7.0 (70/5/2) Operation Instructions online. Page 6

Instruction Huter GMC-7.0 (70/5/2) for the device the cultivator contains pages in Russian.

File size: 612.21 KB. Consists of 16 pages.

You can download PDF file of this instruction: download pdf

Observe extreme caution when changing the direction

Always keep a safe distance regarding other people,

Always check the cultivator before work to make sure all

handles, fasteners and safety shutters are in the working state and on the spot.

Always carefully serve and check your cultivator.

Follow the service instructions specified in this manual.

Always store the cultivator in a closed dry place, inaccessible to

Do not try to clean the mills during their rotation. First

Disconnect the motor and wait for a complete stop of the milling.

Do not let children or incapable of such work people,

Do not work with a cultivator in a state of alcohol or

Do not try to fix this cultivator yourself. For implementation

qualified repair contact the official Huter service in your region

Do not refuel the cultivator with fuel near the sources of open

fire. Before refueling, drown out the engine and make sure that it has cooled down.

Do not refuel the cultivator and do not work

Do not start the engine when the ignition system malfunction

Do not leave the engine on if you temporarily stop

Drown out the engine before moving the cultivator from one

Do not start the engine if there is a smell of gasoline. thirty. Do not work with the cultivator if the gas was spilled during

Refuelings. Before starting, thoroughly wipe the surface of the cultivator from randomly spilled fuel.

Do not work with the cultivator if the edges of the cylinder and muffler

Do not touch the hot muffler, and the ribs of the cylinder, since

Using fasteners, install brackets on the cultivator frame

Install the upper control handles using bolts with a nut from

Install mills using fingers and codes from the kit; four. Set the right and left side protection using bolts from

Install a snoker using a finger and a slap. 6. Install the support wheel.

Instructions for Huter GMC-7.0 (70/5/2)

one. Introduction 4 2. Main technical characteristics 5 3. Safety precautions 5 4. Assembly and adjustment 6 5. Oil level check 7 6. Engine launch 7 7. Cultivator cleaning and maintenance 8 8. Storage 9 9. Possible malfunctions and methods for their elimination 10 10. Unified service

Introduction Dear Buyer, thank you for purchasing products of the Hűter trademark, which are distinguished by reliability and high quality of performance. We are sure that our products will become your assistant for many years. We try to work with a motor.cultivator to be pleasant and

Main technical characteristics model type of engine power/engine volume, l.C/ cm3 transmission of the front/ reverse processing width, cm diameter of the milling cutter, cm volume of the fuel tank, l GMC-5.5 4 stact, one-cylinder 7.0/208 GMC-7.0 4-stroke, one-cylinder 7.0 / 208 1 forward / 1 ago

Observe extreme caution when changing the direction of movement on the slopes. 16. Always keep a safe distance regarding other people who work with you. 17. Always check the cultivator before work to make sure that all the handles, fasteners and

The cultivator is designed to work in the garden and garden. Carefully read the engine operating manual, special attention, paying the chapter, which describes the start and stopping of the engine. In order to avoid oil entering the combustion chamber while working, keep the engine horizontally. Tilts

Pull the starter handle until you feel resistance, then return it to its original position and sharply pull the handle on the handle. After starting, warm the engine for about one minute, opening the air damper as they warm up. Adjust the desired turns

Checking the spark plug (for malfunction) 1. Check the gap of the spark plug (0.7-0.8 mm) 2. Check the degree of wear of electrodes. 3. Check the presence of oil and other contaminants on the insulator. four. If necessary, replace the candle. eight. Storage attention! The danger of an explosion explosion

Possible malfunctions and ways to eliminate them. The malfunction of the engine does not start the engine works uneven cutters do not rotate increased vibration reason in the fuel tank, there is no gasoline. Old gasoline, pour clean and fresh gasoline, pour the old and pour into the tank into the tank

Unified Technical Support Email: Servis@Huter.Su site: www.Huter.SU Address of your service center:

Dear buyer! We express great gratitude to you for the choice of a motor.cultivator “Hűter”. He will last you for a long time. We have done our best so that this product satisfies your needs, and the quality corresponds to the best world samples. The manufacturer company establishes a calculated

Certificate of acceptance motor.cultivator “Hűter” _ No. _ is recognized as suitable for operation. Sales date _ I am a buyer/representative of the company

For notes: _ _ _

Instructions for Huter GMC-7.0 (70/5/2)

Unified Technical Support Email: Servis@Huter.Su site: www.Huter.SU Address of your service center:

Certificate of acceptance motor.cultivator “Hűter” _ No. _ is recognized as suitable for operation. Sales date _ I am a buyer/representative of the company

For notes: _ _ _

Huter-7500.

Hello lovers of motoblocks).I have the first one.axic tractor. I decided to cultivate the site mechanically.) There was no particular choice, since I do not know all the subtleties of these devices. One neighbor has an ancient one.like tractor, I do not know the name, the other has Neva. Both are not happy. I asked people, everyone is advised by OKU. But money is in a sawn.off shotgun, as always, and my plot is not large, hundreds of hundreds of power and something serious is justified to take.Scored in the search engine, the cheapest. A bunch of MB came out and look exactly the same, only the names are different. from 21 to 28. Only 23 on hand.And then one announcement in the store digital technique of DNS jumped out. Huter 7500.I read reviews everywhere like norms. The cost is only not very 27900. But this is my favorite store and there is a discount card. Ordered at a discount, the price immediately fell to 23203 r. Bought.They did not open in the store, as usual in this store. You will come home, look, you won’t like it, you will bring back within 2 weeks, we will return the money right there.Brought home unpacked. But there is no wheels in the picture. There are adapters to wheels, but there is no. There are also bolts for the front bandwidth, but there is no footboy itself. Milling cutters is true in the kit.I went to the store, no wheels I say. Take back. No, I will not give me I say. Call in the call, they said no data that should be in the box. Go to your seller and negotiate. He came again. They say either vese back or discount. Let’s a discount. Threw off another 5000.Total Unoa tractor cost 18,000.Now about the walk.behind tractor. Started, turns above average, are not reduced. Remove the tank, clamped the spring with a tank. Rearranged, everything worked. Dull, but he does not stall. The Stop Stop button is not active. Climbed to the coil, as if the wiring flew out of. Mom, fixed.The neighbor gave the soil.spaces, from the Neva, though they say they skid. He overshadowed the holes.Everything seems to be so far, who has read well done.Now in search of cigns and potato.rowing. And the wheels still need to be bought probably.

Device

Most of the models have 4 main speed transfers. 2 front and two rear, however, some modifications may contain a larger or smaller number of operating speeds. All Huter motoblocks are equipped with a steering wheel with anti.slip nozzles and the ability to adjust its height. Motoblocks work on gasoline, however, diesel machines are also found. All devices have a four.stroke engine, as well as a tank capacity, which is from 3 to 6 liters. In addition, the devices are equipped with a convenient speed switch, a gearshler gear and various motor cooling systems and the main nodes in the mechanism.

There are modifications of devices that are supplied with pneumatic wheels, most often a technique related to a heavy class is realized in this way. All units in the course of work publish a minimum of noise, in addition, the working one.based tractor practically does not vibrate. The working depth of land cultivation varies between 30 centimeters in depth with a width of 1.5 meters, but this indicator also depends on the type of milling cutter.

Non.mounted equipment

Each manufacturer offers, together with his products, use auxiliary components. As for the Chinese motor blocks of Huter, they can be operated with the following equipment.

Cutters. The assortment of these tools is quite wide, so the part can be selected specifically for a particular task.
Water pump. A very useful device that is relevant for use in large agricultural areas.
Ground.spaces. The necessary part that increases the momentum and patency of the technique in severe types of soil. The use of this detail in the offseason and winter is especially relevant.
Nozzle for removing the edges of plants.
Harrow. Tool thanks to which you can make furrows in the ground. Subsequently, they are used to sow crops or watering plants.
Hiller. Performs hilling of beds without using manual labor.
Mower. A tool that allows you to prepare animal feed, as well as harvesting grain.
Adapter. An auxiliary element that increases the maneuverability of the machine, and also makes it possible to use the unoic tractor together with the trailer.
Plow. The most popular tool that is used in conjunction with motoblocks. During the operation and cultivation of land, plows demonstrates much greater efficiency in comparison with the milling.
Snowman. This equipment can be manufactured by another manufacturer. Thanks to an additional device, a single.based tractor can discard snow over long distances.
Clutch. The part responsible for fastening the mounted and trailed equipment to the machine body.
Tears. Elements necessary for light equipment to ensure stability and good adhesion to the soil.

Preparation for work

Huter cultivator is usually implemented in a disassembled form. Therefore, before proceeding with the process of its operation, it is initially necessary to carefully familiarize yourself with the instructions and assembly. After that, you should tune the unit and adjust all its parameters depending on the configuration.

In order to start the Huter cultivator, you will need to perform a certain algorithm of actions, which consists of the following points:

opening of the fuel crane;
closing of the air damper;
the ignition is turned on;
installation of the switch lever for neutral gear;
turning the gas lever in a minimum position;
Pulling up the starter handle until the resistance arises with the further return to its original point and a sharp pulling out.

After the internal combustion engine starts, it is necessary to warm it within 1-2 minutes. This can be done through the gradual opening of the air damper. To adjust the number of engine speeds, the gas lever should be used.

If the Huter motor.cultivator is required, the gas lever should be turned to the minimum position, and then turn off the ignition.

Separately, it is worth paying attention to the fact that when starting a warm motor, in no case should you close the air damper. This can lead to a flood of spark plug.

Hunter Brothers. Sea Shanty

It is allowed in emergency cases to stop the motor engine by turning off the ignition. This applies even to those situations when the gas lever is in the maximum position.

The process of maintenance of cultivators involves checking the level of oil and fuel. Additionally, it is also required to pay attention to the adjustment of the milling plant and its council. After performing a particular agricultural work by the manufacturer of the device, it is recommended to clean all the elements of the unit from dirt, residues of land and dust. As a fuel when refueling internal combustion engines Huter, AI-92 gasoline should be used. The most suitable engine oil for the entire Huter lineup is 10W40 lubricants.

Description

The Huter brand itself has German roots, however, almost all production workshops involved in the production of components and assembly of motor blocks are concentrated in Asia. This territorial separation allows you to reduce the cost of devices, which significantly expands the circle of consumers of agricultural units. The concern is actively engaged in the manufacture of various agricultural equipment, and the first motoblocks went off the assembly line less than ten years ago, so in domestic stores such a technique appeared relatively recently.

According to the owners of such devices, the units are distinguished by a high level of quality and assembly, this feature is due to the presence of multi.stage quality control systems in the production of a system, which positively affects the operational period of German products. However, most of the nodes in the mechanism are not interchangeable, which negatively affects the maintainability of the technique.

Today, the Huter motoblocks have about ten modifications, all products are assembled according to European quality standards, in addition, existing models are modernized in order to exclude possible shortcomings.

Review of attached equipment

Huter cultivators perform the soil processing with milling cutters, aggregated with some hinged tools: plow, hip, potato.cutter, metal soil.bearing. Huter motoblocks with 7.5 liter engines.With. and 9 l.With. have great opportunities for operation with hinged tools.

Installation of the huts on the Huter motoblocks is carried out quickly and allows not only to effectively perform the entire complex of agricultural work, but also to convert the unit into a snow removal, sweeper machine, pump or lawn mower.

The most popular additional devices are: plow, rotary mowers, potato-adhesions and potato-drummers, harrows, mills and baking powers, a water pump, soil-bearing, various coupling, weighting adapters, an adapter with a seat, a minipric, a snowboard, a shovel-off, a household brush.

Features of operation, maintenance

New units are delivered to the sale in disassembled form, so the owner should first familiarize themselves in detail in the instructions with the stages of assembly and the implementation of adjustments.

How to get one.based Huter tractor

Open the fuel valve
Close the air damper
Turn on the ignition
Install the gearbox lever to the neutral
Gas lever turn to a minimum
pull the starter’s handle until the resistance, return to the starting point and then pull sharply.

The launched motor is heated for 1-2 minutes, smoothly opening the damper. The number of engine speeds can be adjusted by the gas lever. The engine stopped by turning the gas lever to the “Slow” mark and turning off the ignition.

In the case of starting the huter motor block with a warm motor, you can not close the air damper, since the spark plug will pour.

For an emergency stopping of a motor block, you should quickly turn off the ignition.

Huter motor work maintenance is to check the level of fuel, motor oil, perform the necessary adjustments of the milling plants, coupons. After work, they are mandatory to clean the unit from dirt, land residues, dust. The AI-92 gasoline is fuel for cultivators and motor blocks of Huter. Mark 10W40 is used as motor oil.

Huter GMC 9 walkover manual.0

HUTER GMC-5 motor cultivators operating instructions.5/GMC-6.5

Playing with kids tractors and new trailer to fix real tractor | Tractors for kids

Running.in, first start

Huter motoblocks are characterized by high.quality reliable components, so their running.in takes a short time. First, they start the engine in accordance with the instructions, let it work for about 20 minutes at idle. Then perform a patch.

In this mode: xx/giving out work within 2 hours. Upon completion, the first change of oil is performed, further replacement is carried out every 10 hours.

Basic malfunctions, repair

Huter cultivators and motoblocks are a solid technique, according to owners, they are not inherent in any typical problems in the work. Malfunctions in most cases arise due to violation of the recommendations of the manufacturer.

Malfunctions in the engine operation (not launched, working with interruptions) are associated with the use of old gasoline, improper position of the air damn, disconnecting the high.voltage wire from a candle or poor contact, pollution of the air filter, clogging of the fuel system.

In order to avoid malfunctions, the slopes of the huter motor block over 10 ° should be as short as possible.

Operation with a low level or without oil is not allowed, this leads to engine breakdown. To check the oil level, it is necessary to drown the motor, to allow the oil to be possible to take it to the crankcase for 4-5 minutes. Next, remove the pike-lid, wipe it dry and insert without twisting, back. At the mark on the probe, determine the actual amount of oil in the crankcase, if necessary, add.

Hyter motoblocks are quite widely common in and the CIS, compared to similar technology of other brands. Therefore, judging by the reviews, the spare parts are not easy to find on them. In the event of some serious problems, sellers of this technique often evade warranty obligations and are unable to help with spare parts. However, such cases are few and, perhaps, in the future they will disappear completely. In the meantime, the specialized Hüter centers and responsible representatives (and not just merchants) who can solve the problem with the walk.behind tractor in a short time.

Most often you can find restraint-gluing reviews about the Hüter GMC-7 model.5. In such a vein that the one-axine tractor regularly works 2 3 4 seasons, without any serious breakdowns, and copes well with its main function (cultivator). In the trunk of the sedan, the uniform tractor is unlikely to fit, only in the station wagon or SUV.

The assembly of a walk.behind tractor is characterized as quite high quality, without frank shortcomings and carelessness. However, many call the design quite a flimsy, and the quality of the metal. leaving the best. However, no one expected the quality of the premium class for such a price. And, despite its visible “flimsy”, this design still holds workloads with dignity, for several agricultural seasons.

Operating guide, which is attached to the Hyuter motornote, is very, very stingy on information. You have to get it on your own, from the video shows of other owners on the Internet. In fuel economy to Hüter GMC-7.5 no one has any complaints: gasoline consumption is practically no different from the declared by manufacturers and never exceeds two liters of fuel per hour of work, in any conditions and at any load.

Noise and vibration from the engine are quite large and sensitive. And they additionally increase when weakening fasteners of nuts and bolts. Therefore, you need to periodically ensure that all fasteners are well tightened.

There is a certificate of work by the Hyter Motoblock on a section of 18 acres, with primrose, an enchantment and a potato.cutter acquired separately. The owner of his compact equipment is satisfied: for three years of operation. not a single breakdown. The same tractor never exhausted, and the engine never worked at the limit. And, characteristic, it did not overheat (which often happens in other motoblocks). At the same time, the owner of Hüter GMC-7.5 notes that he does not understand technology at all, and this is his first one.based tractor.

As a plus, many users also note maneuverability and “responsiveness” in management of this technique. Wheels with a deep tread do not clog with dirt. In order not to damage the milling knives (do not bend them and break them), it is necessary to monitor whether they are clogged with stones, wire or weeds (roots) in the process. If such a winding has gone, you need to stop immediately and clean the mills.

Summing up reviews of the owners of motor blocks Hüter GMC-7.5 can be as follows. This is a compact agricultural machinery, not collected by the highest quality materials. However, the money of his one.time Hyter tractor is worth it, and works out it quickly enough.

Yes, some people were unlucky, and they got a defective product. They encountered problems in terms of spare parts and the quality of service for sellers and representatives of this brand. But, on the other hand, there are few such cases, and their percentage is small.

Basically, we are still talking about high.quality technology, which is working stably and without breakdowns for a number of seasons for a number of seasons. Hüter GMC-7 Unoa Tractor.5 For its class and its price. exclusively productive, functional and profitable, especially when used with primrose. Therefore, it makes sense to immediately acquire them, in addition to the walkover itself.

A few words about installing attachments

After assembling the knives, it remains to install the collected mills on a single.axle tractor using stoppers. For convenience, it is better to raise special equipment and fix it in this position. Next, you need to remove the wheels. Tarein the boiler to carefully put on a support shaft, fix the structure on the left and on the right with a glass. Check the reliability of the connection.

If the cutting of the cutter is completely team, then the installation can be performed sequentially the section behind the section.

The motor.cultivator is recommended only after the correct assembly and installation is checked. There should not be a backlash caused by a weak tightening of nuts, distortions when hanging equipment. Qualitatively completed work guarantees a long service life of equipment and equipment.

Operating principle

Preparation for cultivation

The same.based tractor comes in disassembled form, so first it will have to collect it. For this, the corresponding guide is attached. The procedure is disposable, and does not require repetitions. Then it is necessary to adjust the cultivator to your needs, after which you can start running in. Running.in. a process that allows internal details to work under local conditions. To some extent, this allows you to extend the service life of the entire structure

We draw attention to the fact that during the running.in the load on the cultivator should be no more than 50%. In fact, this is a trial operation, which lasts about 10-15 hours

This time is enough to evaluate the reliability of all components and assemblies of the machine. After the running.in, it is necessary to carry out a control technical inspection, pour new oil and fuel into the engine. The next day you can start full operation.

Description and technical characteristics of Huter motor cultivators

Products are still little familiar to our buyer. But it is worth noting immediately that all manufactured models of motor cultivators meet European requirements and can compete with well.known models of motorized equipment in the agricultural segment. All cars are strictly controlled at all stages of assembly by specialists from Germany.

German motor cultivators have established themselves in the market with their quality and practicality

Even the absence of a dealer network with service centers in the territory does not stop those who want to purchase this motorcycle engineering. Cultivators effectively cope with the treatment of soil using attached additional equipment: a plow, diggers for potatoes, soil for the wheel pair, mills, weighting, adapters and trailers. Fastening devices is carried out quickly and easy. The machine can be used for communal needs: remove snow, sweep the adjacent territory, mow grass.

It is important how to properly assemble (install) the “Goose legs” cutters on the motor.cultivator and whether it is necessary to hide them

All models are equipped with four.stroke single.cylinder gasoline engines with a capacity of 5 to 9 horsepower. When it is included in the work, you must first warm up the unit for no more than 2 minutes. The revolutions are regulated by the handle of gas.

If a motor cultivator is purchased in a disassembled form, it is necessary to carefully read the operating manual and adjustment before assembly. In order for the unit to work for a long time and without failures, it is necessary:

wipe it after each use from dust and dirt;
conduct periodic maintenance;
constantly check the level of fuel and lubricants.

In this video, we consider the Huter motor.cultivator:

It is recommended to fill in high-octane AI-92 gasoline as fuel, and semi-synthetic lubricant with a 10W40 indicator will serve as engine oil. Any new mechanical unit requires a short run.in. Huter motor cultivators are made of high.quality details, so at the first start it is enough to let him work no more than half an hour without loads. Then they are bent for 20 seconds and again for 30 minutes of idle. Alternating these actions, the work of a mini-tractor should not stop 2-3 hours.

After the running.in, you need to let the engine cool and be sure to replace machine oil with a new. During operation, the lubricant should be changed every 10 hours of work of the walk.behind tractor.

The reasons for the poor operation of the walk.behind structure:

violation of the recommendations of the manufacturer for the operation of the machine;
pouring old or low.quality gasoline;
The air damper is closed when it should be slightly ajar;
Air filter clogged;
the presence of garbage in the fuel system;
low level of motor oil or inaccurate determination.
Turn off the engine and let it cool.
Drain the oil into the crater.
With the help of an probe-lid, the level is precisely measured. To do this, the probe-cover is taken out, wiped and again lowered into the oil.
Further, a decision is made to pour additional volume to maximum.

GMC 5

The device has a 4-stroke engine with a capacity of 5 liters.With. There is only one speed. forward. The volume of the fuel tank is small and is 1.5 liters, which corresponds to one hour of work on light soils. The same tractor performs the following operations:

The width of the strip that can be passed at a time is 45 centimeters.

GMC 5.5

This model is improved by the presence of a second (rear) speed. All nodes are securely fixed on the support frame. The same.based tractor easily moves and maneuvers in close conditions. The processing width reaches 85 cm at a depth of 30. The power of the motor is increased by 0.5 liters.With. Managing the machine is easy and simple. gas, clutch, speed switching to the handles of a walk.behind tractor.

GMC 6.5

This model is a copy of the previous one, with the exception of the engine. The machine is equipped with a powerful engine of 6.5 liters.With.

This is interesting: Husqvarna Motorculture TF 338.

Sources:

https://manualbase.ru/files/page/6/Huter-gmc-7.0-7052-instruction-online.html
https://service-instruction.ru/manual/207744/Huter-gmc-7-0-70-5-2
https://service-instruction.ru/manual/207744/Huter-gmc-7-0-70-5-2
https://www.drive2.ru/c/579080889586155745/
https://stroy-podskazka.ru/motobloki/Huter/
https://ss-p.ru/remont/motobloki-Huter-osobennosti-i-soveti-po-ekspluatatsii.html
https://kalibrtractor.ru/spetstehnika/motobloki-Huter-osobennosti-i-sovety-po-ekspluatacii.html
https://myinstrumenty.ru/nasadki-i-rashodnye-materialy/kak-sobrat-frezy-na-motoblok/
https://allautopark.ru/motokultivator-Huter-gmc-5-5-6-5-7-0-kultivator-otzyvy-popularnye-modeli-instrukcia-po-ekspluatacii/

Articles assemble, based, huter, single, tractor