How to change a fishing line for a trimmer for a Patriot benzotrimmer.

Patriot fishing line for trimmer and coil: how to make them together

The main element of the trigger is a mowing head, which is a cylindrical case with a snut.inserted coil (bobbin). A fishing line for a trimmer (cord) is being refueling into it. The heads differ from each other by serving and refueling the cord. There are three types of heads in total:

  • Auto. Then the fishing line for a trimmer is supplied when the user lowers the frequency of rotation of the motor. Automatic supply of the cord is very comfortable when there is a lot of work to do. The shortcoming of such a head. Large thread consumption.
  • Semi.automatic. The introduction of such a head does not ask for the user of the implementation of some complex manipulations. The principle of its operation is arranged so that the fishing line for the trimmer begins to automatically lengthen while the trimmer for the grass works at its entire speed. For you, you just need to hit the car with the head of the car a little (this will remove the fishing line), and the cord will come out of the bobbin due to centrifugal force. Then the fishing line for the trimmer is cut to the desired length with a knife, which is located on a protective cover.
  • Control. To lengthen the cord, the car must be suspended. After that, the fishing line for the trimmer will need to be removed manually.

Preparation for replacement

For clarity, the mowing head (coil) was removed from the mower. To replace the fishing line, you do not need to remove it, everything is done locally. It does not take a lot of time.

We disassemble the coil of the trimmer for the grass, holds on the latches. Remove the lid by clicking on the latches. If your hands do not have enough effort, then use a screwdriver.

The mechanism of work is subsequent. When clicking on the button, the coil presses on the spring and comes out of the fixing grooves in the coil lid. Holding in this state, the coil can be twisted, adjusting the length of the fishing line. When the button is released, the housing spring returns the coil to the initial fixed state.

On the day of the coil, there are several holes for various diameters of the fishing line. They may differ from the manufacturer of a trimmer for grass. In some cases (for example, here) they are signed in others. No.

These holes are necessary to fix the fishing line when replacing it. Having wiped a fishing line for a trimmer to a bastard, the ends of the last are inserted into them. This is necessary so that the fishing line for the trimmer does not spin when installing the coil in the trimmer body for grass. In other words, this simplifies the substitution of the line.

There are models without indicating the cross.cutting expense of the consumer. Then, to find out what the largest diameter of the fishing line can be used, it is tried on the holes to remove the fishing line from the trimmer coil body for grass (see. Sketch below).

Installation on the holes of a linear output

The coil has two sections of the fishing line broken by the partition. They may not be. They are necessary only to distinguish and facilitate the winding of consumables.

At first, the required length of the loss is determined. The latter is wound into one of the coil sections, so as not to go beyond it. With all this, three mm was wound, the length was about two meters. Those. For 2 sections, a segment of four meters will come in handy, this is for the 1st method. For the second method, two segments of two meters each are useful.

Now you need to figure out which way it must be wound. For this, many trimmers manufacturers apply special designations to the coils, as in the figure below.

If there are no such designations, then it is necessary to direct attention to the coil body. There is certainly an arrow indicating the movement of the mowing head. The fishing line for the trimmer is wound in the opposite direction.

Is it possible to make a coil for a trimmer for the grass with your own hands

On sale there are a large number of trimmer heads (not automatic), which have a low price and good quality. But sometimes situations arise, for example, in the country, when the trimmer coil broke, and its repair is impossible, the store is far away, and you need to mow. In this case, you can quickly, literally in a few minutes, make a simple trimmer nozzle to fix the fishing line from ordinary plywood 10-12 mm thick.

  • Take a piece of plywood or textolite and draw a circle with a diameter of about 14 cm on it.
  • Cut the disk with a jigsaw or hacksaw for metal.
  • Drill a hole in the center of the disk, suitable in diameter to the gear shaft. Do not forget before installing a disk on the shaft, put a puck on it.
  • You can fasten small corners along the edges of the disk or make 1-2 holes on the opposite sides. They will serve for refueling fishing lines in them.
  • To fix the fishing line for a trimmer, you can screw several screws into the plywood.

Such a homemade mowing nozzle is fixed on the shaft with a nut. Twist or unscrew the nut without fixing the shaft will not work. To replace the cord, it will be enough to release the screws, insert a segment of the fishing line of the required length and press it again.

Also, a mowing nozzle for fixing the fishing line on it can be made from a metal sheet. How to do this can be understood from the next video.

How to remove a coil from a trimmer for grass and extract a fishing line for a trimmer

Initially, before filling the fishing line for the trimmer to the coil of the trimmer for the grass, it is necessary to extract it from there. Coil or tip is a device that is located inside the braid, bobbin or drum. The heads are of different types (depending on the manufacturers), however, the principle of replacing the fishing line on the coil has the same. First of all, we will figure out how to remove the head from the tool, as well as how to get a drum with a fishing line from it.

It is interesting!The replacement of equipment can be done directly on the tool, but if you do it for the first time, it is still recommended to remove the head, and study the detailed process of winding. After the technology is mastered, you can perform work on replacement on a trimmer of a motorcycle or a gas station.

Instructions on how to promote a hand head on a trimmer, has the following look:

  • Turn the instrument with the head to the top, and if necessary, cleanse it from pollution. Take two fingers of one hand by the cover of the cover (on the mowing head), which are located symmetrically to each other. After a light pressed inward, dismantle the protective cover from the drum
  • Next, from the rampart of the drum, the coil for the fishing line should be removed. It is planted on a shaft without fasteners, so it is dismantled with one hand
  • The main part of the drum is fixed using a screw, which must be twisted with a screwdriver with an appropriate tip or a bat
  • To twist it, it is necessary to hold the base of the drum with one hand, and the second to remove the screwdriver against the direction of the clockwise
  • After that, you can proceed to dismantle. To do this, you do not need to pull it with all your strength, but slightly shaking it, slowly remove it from the hook with a metal shaft on which the drum is planted
  • When installing the installation, the head should be planted in a tetrahedral slot

Read how to wind a fishing line for a trimmer trimmer for STIHL trimmer

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how replacement is performed. When dismantling, consider the following nuances:

  • It is recommended to remove the head periodically to prevent the corrosion of the threaded connection. If you never unscrew the screw, then if necessary to do it will be difficult and even sometimes impossible
  • If the screw has a tetrahedral boring of the head, then for twisting you should select a screwdriver or bit of a suitable size to eliminate the licking of the faces on the head
  • When assembling the installation, a threaded seat should be treated with lubricants, for example, solidol or machine oil
  • If the edges on the screw are licked, then for its unscruptions you can use special clamping forceps
  • There are drums that do not require preliminary disassembly. To dismantle them, you should take up it, and rotate in the opposite direction of the direction of the clockwise

How to open a self.supporting coil (spool) motorcycles.

Knowing how to disassemble the drum, you should continue to clarify the process of replacing a trimmer fishing line for grass. Below the video shows a detailed process how to open a trimmer coil for grass and disassemble it.

Instructions with a step.by.step description how to wind the coil of a trimmer for grass and lawn mower

In order not to make a mistake with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the coil. This information is usually presented on a tip, which will not allow us to make a mistake using the appropriate equipment.

If the information on the coil about what diameter the fishing line for the trimmer can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the equipment, it remains to figure out how to charge it. There are two ways for this, but not for all they are applicable. Consider both methods in details, and already depending on what models and trimmers you use, you are determined on your own which option is suitable.

It is interesting!The principle of how to wind a fishing line for a trimmer for a tip of motorcycles is appropriate not only for autonomous benzar groups, but also for electric trimmers.

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work

In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue and turn the lid a little, after which the lid is easily removed at the time of squeezing the tongue-fixer, you need to slightly turn and raise the head of the head of the trimmer for the grass to extract the winding drum.

change, fishing, line, trimmer, patriot

Step two: extracting a winding drum (coil) with a fishing line

The next step in the process is the exhaust drum with a fishing line from the inner region of the head. You need to turn the head with an open side to see a fishing line for a trimmer and a reel. On the side of the head, find two recesses (eyelets) through which the fishing line for the trimmer is bred outside.

You should release a fishing line for a trimmer from the holes by checking the drum. Then gently remove the coil from the head of the head. The winding drum of some models is installed on the spring. This moment must be taken into account by performing the operation to extract.

The procedure for extracting a coil of a trimmer for grass with a fishing line from the inner region of the head: 1. head assembly with a coil; 2. extracting neatly with a small axial turn; 3. extracted details of the old fishing line for a trimmer are completely removed from the coil. To remove the old fishing line for grass, you need to remove the forest from the loops and pull the free end. This method is removed by the whole old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

How to choose a fishing line for a trimmer for a trimmer for grass

The trimmer for the grass bought in the store is already ready to work. a standard nylon fishing forest is tucked into it. She cuts the grass, but does not cope with work poorly. only young, thin plants quickly fail and mows. She does not take old grass and weeds with stem stems or cuts off at all, wear out quickly. It grabs it for a short time, after which you need to replace the fishing line for a trimmer in a trimmer.

Як намотати волосінь на косильну головку тримера. Як замінити волосінь в голівці тримера.

It is not recommended to use a fishing fishing line for a trimmer, it is better to take a special thread with a fiberglass core. It is sold in construction stores. Stop your choice on an option that has a square or triangle in a section. their sharp edges will work like knives.

Fishing line consumption for a trimmer for grass using faceted and reinforced consumables will decrease by 2-3 times, performance will increase by the same amount compared to the circle of round section and fishing line not reinforced with fiberglass.

Purchase material with a diameter not less than recommended by the manufacturer. If the diameter is unknown, you need to look at the size of the holes on the outer body of the mowing head: the diameter of the working thread should be slightly smaller than the hole to pass through it freely.

Buy a sufficient supply of cutting thread (with 2-3 replacements), try to buy different options to compare which one is best in work.

Upon learning how much material is needed for one winding, focus on the length of the forest during the next purchases, so that there are no too short for winding pieces.

To replace the forest on a mechanical spit with your own hands, you need to disassemble the braid head and get the coil on which the working thread is wound.

How to remove a fishing line for a trimmer

To replace a fishing line for a trimmer in a trimmer, remove the head cover. To do this, press the fingers of the latches of fixers located on both sides of the lid, and pull the lid up. Access to the coil will open. After that, pull it out, pulling up the axis on which the coil sits. If the ends of the fishing line stick out from the holes of the head, then lift the coil along the axis and pull the remaining fishing line from the holes of the head. Now the detail does not hold anything and it is easy to remove and remove the remaining working thread.

The coil is divided into two parts by the central partition with a neckline. Different models of cobs differ in size, so you need to check how much you can wind the fishing lines on the bobbin. Its length ranges between 1 and 4 m.

How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction

Warranty production of the factory refueling of a trimmer for grass will inevitably require replacement of fishing line. Having a very approximate idea of ​​how to fill the fishing line for a trimmer to the coil of the trimmer for the grass on their own, beginners are reluctant to take this matter. However, with some skills, the development of this simple science does not represent any difficulties, and the presented instruction below will facilitate this process as much as possible.

Trimmer for grass is the necessary and useful tool for a summer cottage and a private house. Many own and actively use it, but not everyone knows how to replace a fishing line for a trimmer in a trimmer, especially at first.

In this instruction, we will analyze the entire replacement process step by step. Looking ahead, there are two ways to refill a fishing rod with a fishing rod. There is no fundamental difference. the difference is that in the first case, one fishing line for a trimmer will be refueling, folded in half, and in the second there will be two segments of these forests.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

change, fishing, line, trimmer, patriot

Trimmer device for electric grass. How to disassemble a trimmer for Bosch Art 23

LED lighting lighting device for lighting the aquarium inexpensive and harsh. Bosch Art 23 SL trimmer for grass when working. How to get a lawn mower. gasoline trimmer for grass.Starting a cool lawn mower. Trimmer for grass Electronic Skil 0735 AA. trimmer for grass Bosch Art 26 SL Full video

Trimmer for Forte EMK-360 grass, fishing line substitution. Malline for a summer residence from a gas balon on their own. How to wind a fishing line for a trimmer to a trimmer coil for grass. Trimmer for Bosch Art 26 Combitrim. Cheap trimmer for Bosch Art 23 SL grass. How to wind a fishing line for a trimmer to a trimmer coil for grass? Bosch Art 23 Easytrim Trimmer. Bosch Art 23 SL. How to assemble and start a trimmer for grass (motorcycle).four. Chickens for chickens.

This trimmer for the grass has no need to take a coil every time, it is very important to change the fishing line for a trimmer in an existing coil for a new ske. Bosch Art 23 EasyTrim Trimmer according to the annotation must have a fishing line for a trimmer with a width of 1.6 mm, but this unit is perfectly transferred and a fishing line for a trimmer with a width of 2.7 mm

And it happens that I wish to note that 2.4 mm fishing line will facilitate the mowing process

Bosch Art 23 EasyTrim Trimmer according to the annotation must have a fishing line for a trimmer with a width of 1.6 mm, but this unit is perfectly transferred and a fishing line for a trimmer with a width of 2.7 mm. And it happens that I wish to note that 2.4 mm fishing line will facilitate the mowing process.

Fix the reel support 16 so that it does not spin.

Turn the coil cover 14 counterclockwise and remove.

Draw the end of the latest fishing line in other words of the refitted coil through the hole

Install a coil with a lid 14 on the support

Now you need to take 5 meters of the latest fishing line and fold in half (to find the middle). In the middle part of the coil there is a recess (in some structures. a hole), for which you need to hook our fishing line for a trimmer. There is an arrow on the coil showing the direction of winding. Fundamental detail. if the coil has two.

Many owners of garden motos are perplexed by the question of substitution of fishing line in a trimmer head. In this case, it is transformed in the whole deed, capable of bringing into a non.working state not only a tool, at the same time mowing. To prevent a similar situation, we will analyze in a stages the process of replacing the cord (fishing line) in the nozzle.

change, fishing, line, trimmer, patriot

Remove the nozzle from the gearbox. For this purpose, you need to cooperate the lateral hole or the upper curly washer and excavation on the axis, stick the screwdriver and fix the shaft from scrolling. Then you can unscrew the nozzle. It should be kept in your head that the thread on the shaft has a left clipping, respectively, you need to unscrew the element, turning it to the right.

The subsequent step will be disassembling the case of this node. Usually the lid is attached through the holes-cuts using fixers. To open it, you need to drown the latch into the body and squeeze the edges of the lid. If the nozzle has an automatic or automatic line for feeding fishing line, it means that there is a spring that is when.

I wish to intend the current theme of summer residents and gardeners of the entire post.Soviet place “How to refuel a fishing line for a trimmer to a trimmer for grass”. Few trimmers auto industry in their own operating instructions answer this question. Therefore, ordinary gardeners are hard to figure out how to do it correctly.

Removing and disassembling the coil

The braid trimmer head consists of a casing, a spring (not in every model), bobbins with a cord, cover. Before proceeding to disassemble the coil of the electric unit, be sure to turn off the trimmer for the grass from the network. The disassembly method depends on the mounting of the mowing head. First option:

  • To remove the lid covering the inside of the head, click on the latches (latches), which are located on its two sides.
  • Remove the lid under which you will see the spool. remove it from the body. Some trimmers have a spring under the bobbin coils, which should also be carefully pulled out.
  • Removing the bobbin, you will see the screw in the center of the case. Unscrew it with a screwdriver.
  • After extracting the fasteners, take the case body and, shaking it in different directions, remove the gearbox from the shaft.

In the second version, the head of the trimmer for the grass is twisted onto the shaft of the gearbox. To remove it, you need to fix the shaft. To do this, in such devices there is a hole through which a thin screwdriver or metal rod is inserted. Brief Instruction:

  • Insert a screwdriver into a special hole, then stall the shaft.
  • Get the body of the head and start twist it. This should be done clockwise, t. to. Larva shaft thread.

Field winding algorithm

Depending on which model of the trimmer for grass is used, the type, thickness and length of the fishing line is selected. The diafle of the cord can be from 1.2 to 4 mm. It is not difficult to think of that the thicker you will refuel the cord, the more hard and thick grass it is able to cut off.

In order to find out which line of fishing line can be used on your mower, there are 3 methods.

  • Look at the information about the thickness of the cord in the annotation to the apparatus.
  • Look at the backpack itself. It can be given information about the likely dialects of the fishing line.
  • Put the fishing line for the trimmer to the output. If it passes into it without effort, then the cord of such a diameter can be used.

wound on a coil in a mowing head. Therefore, at first it must be opened (this was mentioned above). There are 2 methods of winding the cord.

The technical properties of the cord and the selection of diameter by the power of the trimmer for grass

If you take the packaging of the fishing line in your hands, then only two main parameters are indicated on it. this is the total length and cross section. Instructions on how to choose a fishing line for a trimmer for a trimmer for grass is not attached, so you have to find out from specialists. Finding a good specialist is not so simple, especially since every year not only new fishing lines, but also coils are produced every year.

Read how to properly release a fishing line for a trimmer from a trimmer for grass

The first thing to solve is the diameter, thickness or cross section of the cord. All this is one parameter characterizing the performance of work by trimmers, benzocouses, motorcycles and travo.shirts. What sections to buy a fishing line for a trimmer for your trimmer for grass? In order not to make a mistake, you should take with you a segment of the old cord, and provide it to the seller. Based on the segment you provided, the seller will give a similar cross section the cord.

This option is certainly reliable, but it is impossible to call it correct. Why? After all, the choice of fishing line depends not only on the head used, but also on the power of the tool used. To begin with, it is recommended to solve what diameter the fishing line for the trimmer can be used on trimmers and benzocoses, depending on their power parameters:

  • Electric trimmers for grass with power indicator up to 500 W. cords with a cross section of up to 1.6 mm are used.Such tools are designed to cut young grass in personalities
  • Gasoline and electrical units with power indicators from 500 to 1000 W. involve the use of cords with a thickness of 2 to 2.4 mm.Such units with consumables are used to prick thin and thick grass, as well as weeds. In trimmers for grass up to 1 kW, you can install a fishing line for a trimmer with a diameter of 1-1.6 mm, but at the same time it will be quickly wear out
  • Trammers for grass and lawn mowers with power indicators over 1 kW. allow the use of the cord with a thickness of 2.4 to 3.3 mm.Such fishing line can cut thick and dried stems, as well as thick thickets. If the consumable material with a thickness of more than 3 mm does not cope with the task of cutting grass, then metal disks with blades, teeth and knives are used

It is interesting!Manufacturers produce a trimmer fishing line for a trimmer with a diameter of more than 3.3 mm, only it is extremely rare, and exclusively on powerful gasoline units.

What types of forests I am

Frequent type of fishing line, which is actually suitable for all types of coils of the cord of the round section. This is an ordinary fishing line for a trimmer, applicable to mowing juicy grass, but it will be much more difficult to mow it with dry, and even more so it can not be couraged with a bush.

Usually, the diameter that can mow young grass does not exceed 1.6 mm. The thicker the thread, the more rough the grass it is able to overcome.

There are fishing lines with sharpened faces in the form of a sprocket or square, such an option is more adapted to mowing dry grass just due to the existing sharp faces, but it is more wear and tear and it is inferior in strength to the round cord.

There are fishing lines with advanced aerodynamics with appropriate dentes, scales and notches, a similar product makes less noise, but they use it only on benzos, since the output from the reel is difficult, it is used in most cases with discs, into which segments are inserted into which segments are inserted. The shortcomings of this product are its fragility.

Replacement of fishing line on a motorcycle

How to wind the cutting cord to the coil of motorcycles (trimmer for grass)

The gasoline is manual. Replacing fishing line In the coil

In this video, I show how simple and easy to wrap a fishing line for a trimmer to a handmade coil without the help of others.

In most cases, in gasoline trimmers with a engine of more than 1.5 liters.With. use cords with iron cable snuts. This thread is completely suitable for mowing dry grass and small shrubs. The presence of a core, positively affects the wear resistance of this material. The disadvantage of such a cord is its price, which is significantly larger than the above opponents.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

Бензокосилка ручная. Замена лески в катушке.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

How much fishing line is wrapped

How much fishing line should be charged on a rogue rogue? Experienced fishermen always wrap the fishing line for the trimmer not the length that will be needed to perform casts, but with a huge supplies. This is necessary to secure from possible breaks. Also, if a wicker cord is used, at the end of the season you can change the sides of the cord in places, rewinding it to the other side. There will be a savings in expensive expenditure material.

Typically, each coil indicates the amount of fishing line of a certain thickness that a spool can accommodate. Even a few values ​​are usually prescribed. For example, “0.25/200 0.30/150 0.40/100”.

If you need to wind a certain amount of meters, you need to calculate what length of the fishing line is 1 turnover of the squel. After that, you can approximately calculate how many revolutions of the handle must be done to wind a certain amount of fishing line or cord. But it must be taken into account that the number of revolutions of the coil handle never corresponds to the number of turns of the fishing line on the spray. For example, in most ore.coils, a fishing line for a trimmer will make 5 turns with one turn of the handle.

Magneto Design and a scheme of work

The transformation of rotation energy into a high.voltage discharge and the formation of a spark that ignites the fuel mixture. In the internal combustion engine, this detail is called Magneto, because in it alternating current is generated from the rotation of a constant magnetic rotor or anchor.

Magneto constructively consists of 2 windings: the highest and low voltage. The condenser with interrupter contacts are parallel to the latter. Whereas the conclusions of the winding of the highest voltage are connected to the candle and body. They are both wound on a core, between the poles of which a spinning magnet is installed, magnetized longitudinally.