How to change a vein in a motorcycle. How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction

How to wind a fishing line for a trimmer for a trimmer for grass: step.by.step guides and video instructions

A beautiful lawn will look truly well-groomed only if you regularly give up grass. For processing complex areas, a trimmer for grass is best suited. Any owner of the unit will sooner or later collide with the solution to the problem, how to wrap a fishing line for a trimmer to a coil, because from incorrect actions you can not only worsen the quality of the mowing, but also disable the equipment. Today in the Homius review, we will talk about all the ways and nuances of the replacement of fishing line and the features of the selection of consumables.

It is convenient to use a trimmer for grass for pumping small or complex areas, for example, near the hedge, between the beds and along the paths. Today, manufacturers produce a wide variety of gasoline, electric and battery models, which can be selected for any requests of the owners.

As a cutting element of a trimmer for grass, a fishing line for a trimmer is used. In the process of work sooner or later, its length will end, and then the owner will arise the question of how to properly replace and fix the thread tucked in the removable coil.

What to consider when choosing a fishing line

Before inserting and fixing the fishing line for a trimmer in a removable coil of a trimmer for grass, it is important to choose the right material.

Rating of the best models of gasoline trimmer for grass. Review of manufacturers and models, as well as useful tips from experts considered in this review, will help in a difficult choice among many models of devices.

By quality

Before you put a fishing line for a trimmer on a trimmer for grass, you need to pay attention to the cross section of the cord:

• Round cross.sections are the most common option. They perfectly give way to grass even in complex areas;
• A line for a trimmer with a spiral section is suitable for thin grass. It is not very durable and is not suitable for old thickets;
• The cord with zabrinki and sharp faces is chosen for mating by the weeds;
• A fishing line for a trimmer with a variety of geometric sections will help to mow the lawn more evenly, but the strength of the consumable material is low.

Important! The most wear.resistant consumables are a two.component fishing line for a trimmer with a round section, enhanced from the inside.

The owner of Motokosi should know that it is categorically impossible to use metal wire, fishing thread and a variety of strings.

Rating of the best electric trimmers for grass. In this review, we will analyze the criteria for choosing an electrochemmer, technical characteristics, as well as the most popular models and brands according to consumer reviews.

In size

Before winding the thread, you should pay attention to its size to the coil of the trimmer for the grass. Most often use a fishing line for a trim with a cross section of 2 mm.

You can choose the right diameter in the following ways:

• View recommendations in the manufacturer’s instructions for trimmer.
• Often manufacturers apply information about the cross.section to the bobbin.
• The cross section of the cord should be suitable for the diameter of the coil opening.

Important! The thicker the thread will be seasoned, the more rigid grass it will be able to mow.

You will need it

Making a cord cord holder

On the outer forming cup.shaped sleeve on the back of the ruler and marker, we plan two marks on the diameters perpendicular to each other.

Then, focusing on the first four marks, we transfer them to the middle of the side surface of the cup.shaped sleeve strictly vertically. We clamp the cup.shaped sleeve into a locksmith and in the marked places with the help of a core and a hammer, we set the drill points, which we do using a drill. Two anti.icing holes should be obtained in perpendicular diameters.

We clean the metal around all four holes, alternately processing them with a manual file. Over each of the four holes on the outside, we install and weld along the nut with a rounded top.

We clamp sequentially two bolts in a vice and directly under the heads, drill through the through holes with a diameter of a little more than two millimeters.

We steal nuts on them and lay both bolts with probably nuts into the annular recess of the cup.shaped sleeve inward symmetrically between the two holes opposite each other.

The location of the bolts should be such that the nuts on them are freely twisted and unscrewed from the head to the top of the holes drilled in them. After making sure that the bolts are laid correctly, we weld them to the sleeve on both sides.

We unwind a two.millimeter cable and pass it at one end through any of the side holes in the cup.shaped sleeve towards the bolt. We pass the hole in it with the rope and pull out the end of the rope out through the hole in the sleeve on the other side of the bolt, helping ourselves with nippers.

We set the required length of the elongated cord and, having measured the same size on the other side, snack the cord in the intended place with nippers. We do the same with the second “Usik”, and tighten the nuts on the bolts using an online key with an effort sufficient for reliable fixation of the “antennae” in a given position.

Typically, the ultrasound rope at large operating speeds quickly decay, lose their strength and begin to break under the influence of a huge centrifugal force. This worsens the work of a trimmer for grass, but what is even more dangerous, they can damage the legs of the operator or people nearby. Therefore, you should make a shell from the solder with a soldering iron along the entire length of the “antennae” from the cable. A soft solder, which has significant plasticity, in contact with the stems of grass and small bushes, extinguishes most of the impact strength and, thereby, protects the cable from destruction. So, a home.made working body of a trimmer for grass is ready.

Alternative way of charging fishing line in a reel

Drums of modern gas.coculuscs, 2 antennae, have a special eye in each of the channels. Thanks to the ears, it becomes possible to wrap the fishing line for the trimmer for each channel separately. For some, a similar method of winding the fishing line is preferable.

• Remove the lid and remove the drum. Usually the cover is fixed with a pair of latches. When the drum is disconnected, access to the spring will open. Do not lose it!
• We wrap a fishing line for a trimmer to one of the channels. Typically, a fishing line for a trimmer is wound against spool rotation.
• We fix the tip of the fishing line so that it does not unwind. Especially for this purpose, the corresponding connectors are provided along the perimeter of the very edge of the drum itself.
• Repeat all of the above operations with the second fishing line. It must be wrapped in one direction with the first cord.
• Collect a coil and put it on a motorcycle.

As a rule, such drums have a traditional hook on the central partition of the channels, and a separate eye in each channel. The user has a lawn mower with such a drum, it is possible to choose a drawing method. Each of the methods is good in its own way.

Below is a video, the author of which clearly shows the above method of refueling fishing. The display of the alternative method begins from the 8th minute exactly, the very first part of the video is devoted to the traditional method of charging the cord.

Types of fishing line for lawn mower/trimmer for grass

To date, a huge number of varieties of cord has been created. The fishing line for the trimmer is not only distinguished by diameter and length, but also by manufacturing material, surface structure and cross section.

But the main criteria for choosing fishing line are:

Almost always the main parameters of the fishing line are marked on the drum itself. over, many manufacturers indicate the parameters of the fishing line not an accurate value, but the range. For example, take a drum with the following parameters: length-2.5-3.5 (m), thickness-1.5-3 (mm). The range makes the law mower more universal. The wider the range of values, the greater the range of work will be capable of performing a mower.

When choosing a fishing line for a trimmer for grass, it is especially important to take into account the value of the diameter. With the growth of the diameter of the fishing line, its strength increases. A good thick fishing line for a 3-4 (mm) trimmer can be used for mowing already formed and stronger weeds. The fishing line is thinner, by 1.5-2.5 (mm), only the mowing of young shoots can be entrusted.

The diameter of the fishing line is directly related to the power of the lawn mower. A thick fishing line for a trimmer is permissible only on powerful and productive units. Typically, a fishing line for a trimmer 3-4 (mm) is placed on the gas mowers with an engine power from 1000-1200 (W).

Regarding the length of the fishing line, the longer the cord, the less often you will have to reload the drum. How else can you classify the types of fishing line for motorcycle.

Surveying and surface structure

The classic of the genre is a fishing line for a trimmer with a round section. Cord with a rounded profile has very solid reliability and durability. But the rounded cross section is well suited only for mowing young shoots, mainly with a thin stem.

If the operator is faced with the task of pumping a well.strong weed with a thick stem, and maybe even dry stem, then the rounded cross section of the cord in this case will be ineffective. For such tasks, a fishing line for a trimmer with the presence of sharp faces is well suited:

Of course, these types of fishing line have their drawbacks. The main disadvantage of the faceted cord is the exposure to rapid wear. Sharp faces tend to break intensively. When choosing fishing line, you need to consider the material. Ordinary cord options are created from plastic. The fishing line for the trimmer is more expensive on the basis of more durable synthetics.

Installation of two forests

Separate types of coils have two eyes, which allows you to fix 2 fishing lines, and not one dual. For this, a plastic cord is bent on the edge to get a hook.

Floor hooks are in a fixation hole on the coil. Next, a simple winding is carried out in the direction of the arrow. In the end, everything gathers in the usual way.

If you know how, then putting a fishing line for a trimmer is not difficult. When this is done only intuitively, you can escape for a very long time by catching the naughty ends of the fishing line, striving to unwind, until the coil rises into place in the head.

Learning to correctly wrap the fishing line for a trimmer to the coil of a trimmer for grass and lawn mowing instructions for installation

Owners of private houses know how necessary the type of tool is such as a trimmer for grass. It can be gasoline and electric, and they differ in the design of power units.

For injection of grass in areas where there are stones, trees and other obstructing objects, a fishing line for a trimmer is used as a cutting device.

This consumable in the process of use wears out, so how to wind the coil of a trimmer for grass, we will consider in detail in the material.

What you need to know about the fishing line on the trimmer for the grass

Fishing lines is called consumable, which consists of nylon, and serves as a cutting device.

Through this equipment, the grass grows, which is ensured due to rotation of the instrument head with a high frequency.

This material has a different thickness, which depends on its use on the corresponding tools of low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers for grass with motorcycles (from 2.4 up to 3.2 mm).

The more powerful the tool, the accordingly there should be a cutting equipment. This affects not only the quality of the injection of grass, but also on the life of the material.

If you ask the question of how to wind the coil of a trimmer for grass, then it’s time to change the reload of the tool.

With the onset of spring, this issue is becoming more and more in demand, so it’s time to understand the step.by.step instructions for replacing the fishing line in the coil of the trimmer for grass.

How to remove a coil from a trimmer for grass and extract a fishing line for a trimmer

Initially, before filling the fishing line for the trimmer to the coil of the trimmer for the grass, it is necessary to extract it from there. Coil or tip is a device that is located inside the braid, bobbin or drum.

The heads are of different types (depending on the manufacturers), however, the principle of replacing the fishing line on the coil has the same.

First of all, we will figure out how to remove the head from the tool, as well as how to get a drum with a fishing line from it.

It is interesting! The replacement of equipment can be done directly on the tool, but if you do it for the first time, it is still recommended to remove the head, and study the detailed process of winding. After the technology is mastered, you can perform work on replacement on a trimmer of a motorcycle or a gas station.

Instructions on how to promote a hand head on a trimmer, has the following look:

• Turn the instrument with the head to the top, and if necessary, cleanse it from pollution. Take two fingers of one hand by the cover of the cover (on the mowing head), which are located symmetrically to each other. After a light pressed inward, dismantle the protective cover from the drum
• Next, from the rampart of the drum, the coil for the fishing line should be removed. It is planted on a shaft without fasteners, so it is dismantled with one hand
• The main part of the drum is fixed using a screw, which must be twisted with a screwdriver with an appropriate tip or a bat
• To twist it, it is necessary to hold the base of the drum with one hand, and the second to remove the screwdriver against the direction of the clockwise
• After that, you can proceed to dismantle. To do this, you do not need to pull it with all your strength, but slightly shaking it, slowly remove it from the hook with a metal shaft on which the drum is planted
• When installing the installation, the head should be planted in a tetrahedral slot

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how replacement is performed. When dismantling, consider the following nuances:

• It is recommended to remove the head periodically to prevent the corrosion of the threaded connection. If you never unscrew the screw, then if necessary to do it will be difficult and even sometimes impossible
• If the screw has a tetrahedral boring of the head, then for twisting you should select a screwdriver or bit of a suitable size to eliminate the licking of the faces on the head
• When assembling the installation, a threaded seat should be treated with lubricants, for example, solidol or machine oil
• If the edges on the screw are licked, then for its unscruptions you can use special clamping forceps
• There are drums that do not require preliminary disassembly. To dismantle them, you should take up it, and rotate in the opposite direction of the direction of the clockwise

Knowing how to disassemble the drum, you should continue to clarify the process of replacing a trimmer fishing line for grass. Below the video shows a detailed process how to open a trimmer coil for grass and disassemble it.

Depending on the manufacturer, the heads differ structurally not only externally, but also inside. Most drums have a clamping spring inside (semi.automatic and automatic).

The instruction is presented above how to disassemble the head of the trimmer for grass without a spring, t.e. on a manual.type head.

The principle of dismantling a semi.automatic head with a spring inside almost identical above described instructions.

The principle of operation of the semi.automatic coil of the trimmer for the grass is as follows:

• Inside the head is a coil, which is planted on slots that prevent its free movement
• The coil is affected by a spring that presses it to the slots located in the design of the lid
• A fishing line for a trimmer is wound for a tip, the length of which depends on the tool itself. Usually this length is from 1 to 4 meters
• During the work, if it is necessary to increase the length of the fishing line, the protruding part of the drum occurs, through which it comes out of the hook with the slots. In this case, the fishing line for the trimmer is wound from the drum, increasing in the length
• Having released the required amount of fishing line, you should release the pressing, and continue to perform work on the injection of the grass

The advantage of the tool with a fishing line is that this consumable does not require sharpening compared to metal disks. In addition, if a stone or tree comes across the way, then the fishing line for a trimmer simply breaks off, without having a negative effect on the gearbox and the engine engine, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to proceed to the consideration of the process of refueling the fishing line into the coil of the trimmer for the grass. After all, it is precisely this moment that most owners of the Special Instruction causes difficulties.

In which direction to wind a fishing line for a trimmer on a trimmer

How to correctly wind a fishing line for a trimmer to a trimmer coil for grass

Many, having developed a factory fishing line for a trimmer on a not so long ago received by a trimmer, try to wrap the latest, but they can’t, because they don’t know how to correct the fishing line for a trimmer to the heel (bobbin) of a trimmer for grass. As if there is an abstract, but still does not come out. Let’s try to deal with this issue in this article.

So, in order to wind a fishing line for a trimmer, it is necessary, for a start, to remove the coil from a trimmer for grass. this will be more convenient. The removal method will depend on the type of trimmer for grass.

How to wind a fishing line for a trimmer to a mowing head of a trimmer for grass or motorcycle

The video carefully shows how to wind a fishing line for a trimmer to a trimmer coil for grass or motorcycle. The gas line is dressed

How to wind a fishing line for a trimmer to a trimmer coil for grass?

The answer to the question after the previous video.

than 200 types of trimmers in one place at the lowest prices. Press and look

Now, having removed and dismantled the coil, we proceed, in fact, to the winding.

Winding process

If your coil is created for work with only one antennae, then everything is very simple here.

It is necessary to rewind 2-4 m of fishing line (depending on the size of the coil), find the hole for the trimmer on the inside of the coil for the coil, stick one end of the fishing line there and start wiring the fishing line for the trimmer in the direction of rotation of the coil on the trimmer.

The inside of the coil is usually indicated with an arrow in which the side is to wind a fishing line for a trimmer. Having wiped a fishing line for a trimmer, we leave a small piece of it unnecessary to put it out.

We fix this piece in a special groove located on the inner part of the coil and created so that at the time of collecting the coil of the fishing line for a trimmer does not unwind. If there is no groove, then you will have to hold a fishing line for a trimmer with a finger, so as not to let it unwind during the upcoming collection of the coil. Further, we take the outer part of the coil and spread the outer piece of fishing line into the available hole, collect and put the coil back on the trimmer for the grass.

In the presence of 2 grooves, a piece of fishing line 2-4 m long is folded in half, we insert the loop in the groove at the groove at the place of 2 grooves, and wrap both ends of the fishing line at our own groove at once. Subsequent acts are similar to the previous option.

That’s all on this issue. How to replace a fishing line for a trimmer in a trimmer how to wind a fishing line for a trimmer for a thrima mowing head. Successful winding!

How to wind a fishing line for a trimmer?

The winding method depends on the type of coil, however, in any case, you first need to choose the right cutting material correctly. On the packaging or in the instructions for each model, the diameter and shape of the fishing line is indicated, it is very important to use just such material, otherwise there will be problems with winding.

The spider is collapsible

Here is the procedure that needs to be performed in order to change the fishing line for the trimmer:

• fix the gearbox of the trimmer for the grass to exclude the rotation of the head;
• Weaken the bolt that holds the fishing line for the trimmer, rotating it with the help of the mesture key counterclockwise;
• pull the remains of the string;
• Cut 2 pieces of a new fishing line of the required diameter, the length of each segment is 20–40 cm;
• Insert both segments into the holes of the coil so that they are separated in half;
• Twist the fixing bolt.

Spider Negrivable and Wind

Here’s how it is necessary to act in order to correctly wind the fishing line for the trimmer to the coil of the lawn mower:

• With your fingers, grab a fishing line for a trimmer passing along the inside of the coil and pull it out of the head;
• Cut a new string into pieces of the desired length;
• Insert the segment into the hole a little more than half the length, then wrap and remove it through the next hole;
• If the fishing line for the trimmer is thick, then you can make pieces of smaller length and, after inserting into the coil, wrap the edge of the string so that it enters the next hole by 0.5–1 cm.

Semi.automatic (collapsible)

Here is the procedure that needs to be performed in order to change the fishing line for the trimmer:

• Squeeze the latches to separate the upper part from the base;
• Remove the upper part and pull out the spool without losing the spring;
• Remove the remains of the old fishing line;
• Cut a piece of string 2-3 m long;
• Fold the segment by half;
• Insert the curved middle of the segment into the sloping of the spool;
• wind the string in accordance with the direction indicators on the rogue or upper cover;
• fix the fishing line for the trimmer on both sides in the slopes of the spray;
• Insert the rogue and the spring, passing both ends of the string through the corresponding holes;
• Install in place and fix the top cover;
• Pull alternately for each of the edges of the fishing line to remove the string from the latch.

Automatic (indiscriminate)

Here is the procedure that must be performed:

• Press the shock button and pull the remaining fishing line from the head;
• Transfer the button to the position of replacing the string, for which combine the tags on it and the upper cover;
• Cut a piece of string 2-3 m long, insert this segment into the reel;
• wind the string, rotating the button, the direction of rotation is indicated on the body.

Field winding algorithm

Depending on which model of the trimmer for grass is used, the type, thickness and length of the fishing line is selected. The diameter of the cord can be from 1.2 to 4 mm. It is not difficult to guess that the thicker you will refuel the cord, the more rigid and thick grass it is able to cut off.

In most cases, a universal fishing line for a trimmer with a diameter of 2 mm is used.

In order to find out which line diameter can be used on your mower, there are 3 ways.

• View information about the thickness of the cord in the instructions for the apparatus.
• Look at the squash itself. It can be given information about possible fishing line diameters.

The fishing line for a trimmer is wound on a coil in a mowing head. Therefore, first it needs to be opened (this was mentioned above). There are 2 methods of winding the cord.

The first way

To correctly determine how many meters of the fishing line are required for a specific coil, it is necessary to wind it on the bobbin so that the skein does not exceed the diameter of the sides. If the fishing line for the trimmer will look out beyond the edges of the coil, you cannot insert it into the casing. After you have decided on the length of the material, it must be tucked in a bastard, so do the following.

• It is necessary to fold the fishing line for double so that one end is 10-15 cm longer from the other.
• Please note that the bobbin is divided into 2 parts by the central side, from which charging begins. Find a groove on it and insert a cord into it, bent twice, putting a slight effort.

The second method

Some coils provide a second method of fixing the cord: you can charge 2 sections of the thread, instead of one folded in half. Fishing line replacement occurs according to the following algorithm.

• Before changing or charging a new thread to the coil, determine how many meters it will be required by the way discussed above.
• Bend one end of the cord in the form of a hook.

There is a very simple and quick way to replace the fishing line for motor.cuts without disassembling the mowing head, which you can see this video.

The ends of the cord sticking out of the holes in the casing can be cut to the required length, already when the part is installed in the trimmer. You can do this in two ways:

• By turning on the trimmer for the grass (when rotating, the ends of the fishing line will part on the knife, fixed for these purposes on the protective casing);
• Cutting the extra ends with scissors so that they do not touch the casing body.

The second method is used if I had to put a large diameter cord, and a trimmed knife cannot shorten it.

If the thread was charged into a mowing head, but the length of the protruding ends of the cord is insufficient, then before starting the device they must be lengthened. this applies to the head with manual adjustment. However, there are cases when using a semi-automatic mowing head, when, due to the insufficient length of the protruding ends of the cord, they do not automatically lengthen. In this case, it is necessary to turn off the unit (on the electric device you need to pull the fork out of the outlet), manually press the button located at the bottom of the part, and stretch a little fishing line. After this procedure, the cord will be able to advance again thanks to centrifugal strength, if you put the maximum spindle speed.

No matter how thick the fishing line for the trimmer you should remember: in order not to constantly interrupt the work and do not change the cord, you should avoid areas where a working tool can touch hard surfaces (stones, borders, thick dry branches, etc.D.).

How to choose a fishing line for a trimmer for a trimmer for grass

The trimmer for the grass bought in the store is already ready to work. a standard nylon fishing forest is tucked into it. She cuts the grass, but does not cope with work poorly. only young, thin plants quickly fail and mows. She does not take old grass and weeds with stem stems or cuts off at all, wear out quickly. It grabs it for a short time, after which you need to replace the fishing line for a trimmer in a trimmer.

It is not recommended to use a fishing fishing line for a trimmer, it is better to take a special thread with a fiberglass core. It is sold in construction stores. Stop your choice on an option that has a square or triangle in a section. their sharp edges will work like knives.

Fishing line consumption for a trimmer for grass using faceted and reinforced consumables will decrease by 2-3 times, performance will increase by the same amount compared to the circle of round section and fishing line not reinforced with fiberglass.

Purchase material with a diameter not less than recommended by the manufacturer. If the diameter is unknown, you need to look at the size of the holes on the outer body of the mowing head: the diameter of the working thread should be slightly smaller than the hole to pass through it freely.

Buy a sufficient supply of cutting thread (with 2-3 replacements), try to buy different options to compare which one is best in work.

Upon learning how much material is needed for one winding, focus on the length of the forest during the next purchases, so that there are no too short for winding pieces.

To replace the forest on a mechanical spit with your own hands, you need to disassemble the braid head and get the coil on which the working thread is wound.

How to remove a fishing line for a trimmer

To replace a fishing line for a trimmer in a trimmer, remove the head cover. To do this, press the fingers of the latches of fixers located on both sides of the lid, and pull the lid up. Access to the coil will open. After that, pull it out, pulling up the axis on which the coil sits. If the ends of the fishing line stick out from the holes of the head, then lift the coil along the axis and pull the remaining fishing line from the holes of the head. Now the detail does not hold anything and it is easy to remove and remove the remaining working thread.

The coil is divided into two parts by the central partition with a neckline. Different models of cobs differ in size, so you need to check how much you can wind the fishing lines on the bobbin. Its length ranges between 1 and 4 m.

We change the fishing line for a trimmer in a trimmer (lawn mower)

Many owners of garden motorcycles are at a standstill issue of replacing fishing line in a trimmer head. Sometimes this turns into a whole problem, which can bring not only the tool, but also the mower into the non.working state. To prevent such a situation, we will analyze in a stages the process of replacing the cord (fishing line) in the nozzle.

Remove the nozzle from the gearbox. To do this, it is necessary to combine the side hole of the lower curly washer and the excavation on the axis, insert the screwdriver and fix the shaft from the scrolling. Then you can unscrew the nozzle. It should be remembered that the thread on the shaft has a left cut, respectively, you need to unscrew the element, turning it to the right.

The next step will be the disassembly of the case of this node. Usually the lid is attached through the holes-cuts using fixers. To open it, you need to drown the latch into the body and squeeze the edges of the lid. If the nozzle has an automatic or semi.automatic fishing line, it means that there is a spring inside that can fly out when disassembling. Therefore, we hold all the details with a free hand and gently lay out on the surface.

Now we take a fishing line for a trimmer, measure 5 meters and cut off this piece. It is not recommended to wrap the cord, the diameter of which is greater than the value specified in the instructions for the tool. Otherwise you can get an increase in the load on the engine and increased fuel consumption. We fold a fishing line for a trimmer in half to find the middle and get such a “loop”.

On the coil, in the middle part there are 2 recesses located opposite each other (instead of the recesses, there may be holes). Capture the “loop” for one of the recesses and begin to wrap the fishing line for the trimmer counterclockwise. If the coil has two compartments, then the winding goes separately for each branch of the fishing line. We leave the last 15-20 cm cord free and clamp both ends through the recesses in the upper part of the coil.

We collect the feed elements (spring and washer) in the nozzle and remove the free ends of the fishing line in the holes on the case. We put on the lid, clicking the locks in the corresponding grooves. After that we pull the free course of the cord.

It remains to screw the nozzle in place, acting similarly to the first stage. Only now, to tighten the element, it is necessary to move it counterclockwise. Such a simple instruction will help you quickly replace the fishing line for grass, without spending special efforts on searching for other solutions.

As it turned out, the finalization is inherently very simple, and if you had everything necessary, took 10-15 minutes, no more. You just need to have an idea of ​​how to get to a drill and welding machine.

The use of the chain from the chainsaw not only significantly increased the effectiveness of the tool, but also reduced the costs of its maintenance. in any case, I will no longer need a fishing line for a trimmer for a trimmer for grass.

Safety is above all!

Do not forget about safety measures when working with a trimmer! The fragments of the bushes fly over a long distance and with great force. Use personal protective equipment. special mask, make sure there are no people and animals around.