How to change the brushcutter line on a STIHL ride-on lawnmower

STIHL gasoline grass trimmer how to refill your trimmer line. Changing the line for the trimmer in the trimmer (lawnmower)

First of all, for winding the fishing line is required to remove the spool (spool, bobbin) from the grass trimmer. specific actions will depend on the complexity of the configuration and type of the product itself:

• small electric grass trimmers with the working position of the motor and spool at the bottom usually have side keys on both sides of the reel. Pressing them simultaneously disengages the upper part of the bobbin together with the internal contents for winding the line, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the construction does not pop out and get lost;
• electric and gasoline grass trimmers with a curved boom without the possibility of installing a knife, usually have a spool with a special wing nut: in such designs, one hand should hold the bobbin in a fixed position, and the other counterclockwise rotate the fixing bobbin on the boom nut. After loosening the nut the entire bobbin is removed.
• electric and gasoline grass trimmers with the possibility of installing a blade on a straight bar (e.g. STIHL grass trimmers) have a hole under the reel. To immobilize the rod, a screwdriver or other suitable object is inserted into this hole and a slow rotation achieves a mutual arrangement whereby the screwdriver enters the hole and the bobbin is fixed. After that, the spool body is twisted clockwise (with the left thread) and removed from the grass trimmer.

For the second and third cases, the spools, depending on the design, are disassembled in different ways. For spools with a wing nut, the wing nut is unscrewed; for spools with latches, the latches are pressed and one part of the spool is released from the other part. If the bobbin halves are connected by thread, it is sufficient to turn them by hand in opposite directions until they are completely unscrewed.

A bobbin with two operating tendrils

In this type of bobbins should determine the number of grooves for winding the line lying on the inside of the spool:

HOW TO CHANGE A TRIMMER’S BOWL HOW TO CHANGE A TRIMMER’S BOWL HOW TO CHANGE A TRIMMER’S BOWL HOW TO CHANGE A BOWLER’S BOWLER

For both cases a 2-3 m trimmer line is used. In single-cable spools the line for the trimmer is pulled through the through hole, its ends (tendrils) are put together and aligned, and then reeled in the opposite direction to the bobbin rotation direction on the boom. an arrow inside usually indicates the correct winding direction. If there are fixing grooves, the ends of the fishing line are pushed through them or held by fingers of free hand, put into the through hole of the outer half of the bobbin, bobbin is closed and fastened to the rod of the trimmer product.

The difference in the winding of the line in dual spools is that initially a piece of line 2-5 m long is folded in half (to determine the middle fold), and the loop of the fold is inserted into a special groove between the grooves. both line tendrils are wound each in their own groove, fixing the tendrils and reel assembly is similar to the single groove version discussed above.

The first performance of this procedure may seem long and quite time-consuming, but with time and experience, this task will be solved much faster and easier.

The video below will clearly show how to tuck the line for the trimmer into the grass trimmer spool and properly wind it. this operation is not anything complicated and with some patience is sure to succeed:

Reel with one operating rod

The easiest option and uncomplicated sequence of actions:

• The size of the reel and the length of the original factory reel determine the recommended length of line for reeling. 25 m.
• One end of the line is pushed into the fixing technological hole located inside the bobbin.
• the line for the trimmer is wound on the reel in the opposite direction to the rotation of the bobbin on the trimmer product. as a rule, on the inside of the reel an arrow indicates in which direction the winding is carried out.
• A small section of fishing line is left free to exit. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin in working condition.
• The leftover end of the line is fed through the opening on the outside of the spool.
• The halves of the bobbin are assembled and put on the trimmer’s boom.

READ How to Clean the Air Filter on an Echo Trimmer

How to replace a trimmer line on a trimmer?

Replacing the grass trimmer fishing line with step-by-step instructions will allow even an inexperienced lawnmower owner in such matters to perform quite a complex job.

However, before you begin work on replacing the line on the trimmer, it is necessary to ensure the safety of the work. In particular, care must be taken to ensure that the lawnmower does not start accidentally or unintentionally:

• prevent spontaneous triggering,
• Remove the battery (if used),
• Place the tool on a suitable working platform.

Work on the replacement of the grass trimmer line is convenient to perform when the lawnmower is lying on the table, and the master, who performs the replacement of the grass trimmer line, has the opportunity to approach the tool from any side.

Step three: complete the head assembly

Pull line ends through the pair of oval slots on the reel. Replace both washers and spring (if any) with the new items supplied. Bend both ends of the line at right angles.

The last technical step in the process of replacing the line on the trimmer is to place the cap on the head and then secure it by applying pressure and turning it slightly.

Pass each end through the hole at the base of the winding drum. Set the spool in the inner area of the head with the spring in place. To put a cover, align it on the base and with a slight downward pressure with a small counterclockwise rotation, plant the cover on the tongues of locks. This completes the replacement procedure.

Step one: securing and laying down

Fold in half the end of the line. Place the workpiece over the spool on each side of each half of the winding zone. Wrap both halves completely around the winding drum. Pull the trimmer line through the loop.

Procedure for preparing the line engagement in the area of both spooling sections of the reel. The loops are placed in the specially made notches, and then the winding of the fishing line in each area is performed

Tighten the trimmer line just enough and fit the knot into the groove made on each side of the winding drum.

Removing the cover of the grass trimmer head

In the first stage of disassembly, the cover of the grass trimmer head is removed. Using models of trimmers “Black and Decker” and others as an example, to remove the cover is usually enough to apply some force to unclip the latch-fixator, which are located on the side of the head.

On some models of lawnmowers initially provides for the dismantling of the grass trimmer head, for which use the hexagonal key supplied with the tool. The head is usually held by two or three screws, which are accessed through the side holes of the back decorative cover.

The cover of the head, where the filament spool is installed, is usually held in place by a latch tongue. You just have to press the latch with some effort and twist the lid a little, after that the lid can be easily removed

While squeezing the latch release, you need to slightly turn and lift the cover of the grass trimmer head to remove the winding drum.

READ How to Properly Put on a line for a trimmer Grass trimmer

How to wind the line for the trimmer on the grass trimmer spool: methods of winding and

Any owner of a garden plot knows how quickly weeds can flood the area. Effortlessly defeat them with a grass trimmer. This indescribably useful device is an indispensable assistant in trimming and cutting the grass. It’s no secret that an ordinary lawn trimmer can be used far from everywhere. In contrast, the trimmer under force to handle even very difficult areas. This is particularly true for those tools, in which the role of the cutting element is not a knife, but a line for trimmer

Hand-held petrol mower. Changing the line in the spool.

In this video I show you how easy and simple to wind the line for trimmer on the handlebar spool without any help from others.

Changing fishing line in a trimmer: 2 simple ways

trimmer for grass. a suitable and necessary tool for a summer cottage and personal home. Many people own and intensively use it, but not everyone knows how to change the line for the trimmer in the trimmer, especially at first.

In this annotation, we will go over the entire swapping process step by step. Looking ahead, there are two methods of threading the line in the trimmer bobbin. No fundamental difference, the difference is that the first trimmer line is to be tucked in half, while the second line has two lengths of such line.

Changing a line in your trimmer: 2 easy ways

Grass trimmer. a suitable and necessary tool for the garden plot and personal home. Many people have and intensively use it, but not everyone knows how to change the line for the trimmer in the trimmer, especially at first.

This tutorial will show you the whole process step by step. Looking ahead, there are two methods of feeding lines into the trimmer bobbin. No basic difference in principle. The difference is that one line for the trimmer is used first, folded in half, and the second line has two lengths of trimmer line.

Algorithm for winding the line

The order of winding the line depends on the type of spool. with one or two tendrils, as well as with automatic cord charging.

On a spool with a single tendril

It is very easy to wind the line for the trimmer on the spool with one tendril. Depending on the brand of grass trimmer, these designs hold two to five meters of cord. The edge of the line in the bobbin should be tucked into a special hole or groove, then the string is wound to the side opposite to the rotation of the spool during work.

Tip! To understand which way to wind the cord, you need to look at the body of the bobbin. usually there are markings on it indicating the direction of the bobbin’s movement when working.

After the line for the trimmer is wound, you need to leave a small piece (15-30 cm), put it through the bobbin outlet and reassemble the head.

on a spool with two spool strings

With this type of bobbin, you need to inspect the inside of the spool and determine the number of grooves for winding the cords provided in it.

Important! If the reel has one groove, then both tendrils should be wound on a common groove, if two. then on separate tracks.

For winding a piece of fishing line of two to three meters in length is required. For single groove bobbins, thread the trimmer line into the through hole, align the whiskers, align it and wind it onto the spool in the opposite direction of its rotation when working. If fixing grooves are provided, you need to put the ends of the cord in them, then pull them into the exit hole, and then close the spool and put it in its previous place.

For twin-twist spools the difference is that a piece of line must be folded in half. Next, you need to charge the middle of the bend in the groove between the grooves, and then wind each of the pieces of line on its track, fix the tendrils and reassemble the bobbin the same way as a bobbin with a single track.

On a trimmer head with automatic threading

For auto-priming heads, you just have to wind and pinch the ends of the line, and the tool will continue to wind the line by itself when you turn it on. It is impossible to make a mistake here, because the coil itself recognizes how the tendrils should be located.

For your information! The advantages of trimmers with such a head include the convenience of laying the cord, and the disadvantages. the high cost and complicated repair.

Automatic line winding on spool

There is a variety of spools, in which the automatic mechanism produces winding without the aid of others. the user is only enough to correctly tuck the line for the trimmer. How to put lines in the grass trimmer reel? Video instruction. How to take the spool off the weed trimmer? How to wind fishing line for trimmer in order to tuck the line for trimmer. The line for the trimmer is passed through the hole on the inner part of the case, its tendrils are passed through the hole on the outer case without winding, the bobbin is assembled, and when you turn the winding button the line for the trimmer inside is wound without the help of others. In such a bobbin is unreal to make winding erroneously: the mechanism itself will determine the correct direction, as it can spin only in one direction.

Warranty exhaustion of the factory weed trimmer will inevitably require the replacement of the line. Having a very rough idea of how to tuck the line for the trimmer into the grass trimmer reel by themselves, beginners are reluctant to take on this task. However, with some skills, mastering this simple science does not represent any difficulties, and the following similar instruction will facilitate this process as much as possible.

Advance preparation

First of all, to wind the fishing line, it is required to remove the spool (bobbin, bobbin) from the grass trimmer. the specific actions will depend on the complexity of the configuration and the type of the product itself:

• Small electric grass trimmers with a working motor and spool at the bottom usually have side keys on both sides of the reel. When you press them simultaneously, the upper part of the spool with the internal contents for winding the fishing line is detached, while the lower part remains on the trimmer. It is desirable to disassemble the bobbin on a flat, smooth place so that the spring that goes into the design does not pop out and get lost;
• Electric and gasoline grass trimmers with a curved boom without the possibility of installing a knife, as a rule, have a spool with a special wing nut: in such designs, one hand should hold the bobbin in a fixed position, and the other counterclockwise rotate the fixing bobbin on the boom nut, wing nut. After loosening the nut the entire bobbin is removed.
• electric and gasoline grass trimmers with the possibility of installing a blade on a straight shaft (e.g. STIHL grass trimmers) have a hole under the reel. To immobilize the bobbin, a screwdriver or other suitable object is inserted into this hole and a slow rotation is used to position the screwdriver inside the hole and secure the bobbin. After that the spool body is turned clockwise (left-hand thread) and removed from the grass trimmer.

For the second and third cases, reels, depending on the design, are disassembled in different ways. In bobbins with a drum unscrew the drum, in spools with latches press the latches-fixators and one part of the spool is released from the other. If the bobbin halves are connected by thread, it is sufficient to turn them by hand in opposite directions until they are completely unscrewed.

How to wind the trimmer line onto the grass trimmer spool

Winding Algorithm

Lay the line for the trimmer according to the direction shown on the element body.

Insert the short end into the groove on the side of the reel.

Secure the long end in the opposite groove.

Place the spool with the line wound into the bobbin case.

Cut the ends of the line leaving 10 to 15 centimeters.

The filament change is complete and you just need to screw the bobbin onto the weed trimmer and you are ready to go.

What to do:

Before you disassemble the trimmer head, you must be sure to shut off the gasoline grass trimmer engine or unplug it from the mains if the grass trimmer is electric. Turn the grass trimmer upside down, placing it on the handlebars with the trimmer head “looking up” for easy disassembly. Press the latches on the sides of the trimmer head and remove the cover.

Remove the drum (spool) from the trimmer head and remove any residual fishing line from it (there may be a piece of fishing line remaining) and clean the cover, body and spool of soil and grass.

Buy your trimmer line for your trimmer head at your dealer’s service center, in a store, or at the market. The diameter of the line, the shape of its cross section, and the recommended brand cm. In the Owner’s Manual of your grass trimmer and by price level.

Measure and cut the desired length of line from the coil you bought (see “Length of line” on page 12). User manual for your trimmer, usually 15 m). Find the middle of the line by folding it in half.

With the loop formed, hook the trimmer line into the notch on the inside of the reel and wind one half of the line onto one side of the reel first, and then the other half of the line onto the other side of the reel. To prevent the ends of the wound fishing line from unraveling, secure them by inserting them into the notches on the edges of the trimmer head reel.

Insert the drum in the previously removed cover trimmer head and bring the ends of the line through the holes provided in the cover (usually these holes have a metal trim, as during operation have a strong shock and abrasion effects from chopping grass and constantly moving lines). Insert the cover with the reel wound onto the base of the trimmer head and snap into place.

Pull the line ends with both hands until it stops. If the working ends of the fishing line are longer than normal, they will be cut at the first revolutions by the cutting blade, which is usually located on the plastic blade guard of the grass trimmer.

How to wind a line for a trimmer on a grass trimmer reel. the second way

The methods differ in winding. in the second method, use a line for the trimmer of two pieces separately. At the end of the thread, make a bend in the staple as shown in the photo, and thread it into the fixing hole. Wrap two blades of the spool in this way.

• If you have a single-blade reel, look for a hole on the inside to catch the line. Insert the line for the trimmer in one of the ways above. Then wind it on the spool in the opposite direction to the movement of the spool on the trimmer. Leave a small piece of thread and assemble the mowing head.
• When you start the grass trimmer in operation, the excess line will be cut off with the sharp trimmer blade by itself.
• To avoid changing your trimmer line too often and having to stop working all the time, try to avoid touching the technique with hard objects during use.

First of all, to wind the fishing line, it is required to remove the spool (bobbin, bobbin) from the grass trimmer. the specific actions will depend on the complexity of the configuration and type of the product itself:

• Small electric grass trimmers with a working motor and spool on the bottom usually have side keys on both sides of the reel. Pressing them simultaneously disconnects the upper part of the spool with the internal content for winding the line, while the lower part stays on the trimmer. Disassembly of the bobbin should preferably be done on a flat, smooth place, so that the included spring does not pop out and get lost;
• electric and gasoline grass trimmers with a curved rod without the possibility of installing a knife, as a rule, have a spool with a special wing nut: in such designs should be one hand to hold the bobbin in a fixed position, and the other counterclockwise to rotate the fixing the bobbin on the rod nut, wing nut. Once the nut is disconnected, the entire reel is removed.
• Electric and gasoline grass trimmers with the ability to install a blade on a straight bar (such as STIHL grass trimmers) have a hole under the reel. To immobilize the bobbin, a screwdriver or other suitable object is inserted into this hole and a slow spinning motion achieves a mutual arrangement where the screwdriver enters the hole and the bobbin is secured. After that, the body of the spool is scrolled clockwise (with the left thread) and removed from the grass trimmer.

For the second and third case, spools, depending on the design, are disassembled in different ways. On reels with a wingnut, the wingnut is unscrewed; on reels with latches, the latch latches are pressed and one part of the reel is released from the other. If the bobbin halves are connected by thread, it is sufficient to turn them by hand in opposite directions until they are completely unscrewed.

Slowly completing the disassembly of the bobbin spool without losing its parts allows you to move on to the main task. winding the line in the bobbin. Technological features of the bobbin design and the number of working tendrils determine the sequence of operations.

SPOOL WITH ONE WORKING STRAND

The simplest variant and uncomplicated sequence of actions:

• The size of the bobbin and the length of the original factory-wound line determine the recommended line length for winding. 25 м.
• One end of the line is inserted through a catching technological hole inside the bobbin.
• The line for the trimmer is wound on the reel in the opposite direction to the rotation of the bobbin on the trimmer product. on the inside of the bobbin winding there is usually an arrow indicating in which direction the line is wound.
• A small section of the line is left free to be wound outward. it is fixed in a special groove on the inner side of the bobbin, designed to hold the winding when assembling the bobbin to the working condition.
• The leftover end of the line is passed through the hole on the outer part of the bobbin.
• The bobbin halves are assembled and put on the trimmer bar.

BOBBIN WITH TWO OPERATING TENDRILS

In this type of bobbin you should determine the number of grooves for winding the line lying on the inside of the bobbin:

For both cases a 2-3 m trimmer line is used. In single-cable spools the line for the trimmer is pulled through the through hole, its ends (tendrils) are put together and aligned, and then reeled in the opposite direction to the bobbin rotation direction on the boom. an arrow inside usually indicates the correct reeling direction. If there are fixing grooves, the ends of the fishing line are threaded into them or held by the fingers of your free hand, threaded through the through hole of the outer half of the bobbin, the bobbin is closed and attached to the rod of the trimmer product.

The difference of line winding in double-channel spools is that initially a piece of line 2-5 m long is folded in half (to determine the middle fold), and the loop of the fold is inserted in a special groove between the grooves. Both tendrils of the fishing line are wound each on its own groove, fixing the tendrils and reel assembly is similar to the above variant with one groove.

The first performance of this procedure may seem long and quite time-consuming, but with time and experience this task will be solved much faster and easier.

The video below will clearly show you how to tuck the line for the trimmer into the grass trimmer reel and properly wind it. this operation is nothing complicated and with some patience is sure to succeed:

If there is a summer cottage or a large plot of land near your individual house or cottage, then you need to use a lawn trimmer for the convenience of cleaning grass and weeds. If you think to choose between an electric lawnmower or a gasoline lawnmower click here and you will find a comparison of different models.

Over time, the trimmer line on the mower wears out and needs to be replaced. this can be done yourself. You need to choose this polyethylene filament depending on the model of the mower. It is also worth taking a look at the other parts of the machine. the blades of your Craftsman mower, for example, are also subject to wear and tear and can cause irreparable damage.

The design of the spool into which the line for the trimmer is inserted is very simple. But it differs depending on whether the spool works with one or two thread tendrils. It is important to pay attention to safety when changing the line in the spool.

Automatic line winding on the spool

There are many spools in which the automatic mechanism winds itself from the user need only fill the string correctly. Fishing line passes through the hole on the inside of the body, its tendrils without winding through the hole on the outer casing, the bobbin is assembled, and when you turn the winding button inside, the line winds itself. In such a reel, it is impossible to make the winding wrong: the mechanism itself will determine the correct direction, because it can only return in one direction.

Grass trimmer This is a handy and easy-to-use tool for cutting grass and trimming small shrubs and trees. As a cutting element, it often uses a trimmer line (string, cord), because it costs less than disc knives and is safer to use. With heavy use of the tool, you will eventually need to change your trimmer line to a grass trimmer. This process is the same for mowers from different manufacturers, whether Husqvarna or Mechs, with possible minor differences.

The string is not retractable

In automatic and semi-automatic reels, the cord is fed without stopping the grass trimmer. If it doesn’t, it does:

• The fishing line for the trimmer in the head is not properly wound, so the spool does not spin;
• The winding of the mowing line is uneven, so the cord gets stuck between the coils and does not come out to prevent this from happening, you need to carefully wind the thread, avoiding warping, return it to the twist;
• The ends of the cord coming out of the holes are very short, there is not enough centrifugal force to pull them out, so the line for the trimmer does not feed before turning on the grass trimmer, it is mandatory to adjust the length of the cord and lengthen it slightly, if necessary;
• The cord is stuck.

https://www.Artem-tools.ru/articles/kak-namotat-lesku-na-trimmer_327408/ https://www.Vse-dachi.com/kak-namotat-lesku-na-trimmer-pravilno.html https://san-lider.ru/leska/kak-pomenyat-lesku-na-benzinovom-trimmere-video.html https://ingener-pto.ru/2019/12/12/kak-pomenjat-lesku-na-jelektricheskom-trimmere/

Types of trimmer heads

The grass trimmer head is a cylindrical body, in which a spool (bobbin) is inserted with a fishing line (cord) tucked into it. This design can be installed on both gasoline and electric trimmers. Heads differ in the way they are threaded and fed, and come in 3 types.

• Automatic. The filament feed is performed after the user reduces the engine speed. Although automatic line feed is convenient if high volumes of work are performed, such bobbins have one disadvantage. high thread consumption.
• Semi-automatic. Using this type of head does not require the user to perform complex manipulation. The principle is that the cord is pulled in automatically while the machine is running at full speed. It’s enough to slightly knock the head of the grass trimmer on the ground (this removes the cord lock), and the line for trimmer thanks to the centrifugal force is pulled out of the bobbin and then trimmed to the desired length by the blade located on the protective cover.
• Manual. The cord requires the machine to stop, after which the trimmer line is pulled by hand.

Based on the above, semi-automatic bobbins are the best option. Also note that grass trimmer spools come in single-stranded (used only for trimming grass) and double-stranded, which are used for mowing tall grass and small, thin-stemmed shrubs.