How to cut a circle with an electrician in a sheet of metal. How to insert a file into an electrician

The master cuts out perfect circles with a jigsaw. How to cut a flat circle, having only a circular saw from the tools, how to cut an even circle from plywood

Any design, whether in your home, or in production, involves working with metal.

Often, during the operation of this material, the question may arise: how to cut a circle in ?

It deserves attention, since the complexity of the work process and the quality of its result directly depends on the choice of the right tool and technology.

Metal is thin, or thick and durable, so a variety of tools are used to cut it.

The choice of materials and cutting technology also depends on what diameter a circle is needed and how even it should be.

The use of a jigsaw

If there is a need for a perfectly even circle, you can use the electric to cut it.

  • First, the thickness of the metal is determined and the corresponding saw canvas is selected for an electric lobby.
  • Before cutting the circle in the metal with a jigsaw, the circuit circuit is planned on the working plane, which will be cut out.
  • Using a drill and a drill (in the diameter of the component from eight to ten millimeters), a hole is cut out from which work will begin.
  • The resulting gap is placed in the resulting gap and the cutting continues according to the intended.

Cutting using this tool does not take much time and effort. over, with the help of a jigsaw you can get a circle with perfect edges. But this tool is used only to work with the metal of the minimum or medium thickness (for example, 2. 3 mm).

The use of corner grinders

Corner grinder is used to work with metal of small thickness. A round hole can be formed with this tool, following such step.by.step tips:

  • Before cutting the circle in the metal of the corner grinder, marking is carried out so that its contours are clearly visible.
  • In the entire length of the scheduled drawing, short segments are cut out with a disk of corner grinder, which will ultimately combine.
  • The figure will be more similar to a multi.line than a circle. Therefore, after the end of the cutting, the product is processed and cleaned until the time, until the edges become quite even and smooth. For processing, you can also use an angular grinder. If the circle has a wide. You can sharpen the contours in a large disk.

When processing a cut circle with an angular grinder, you should be careful so that the disk is inside the hole and, at the same time, is located in the same plane with a working sheet.

How to cut a plywood jig?

Before cutting a circle of plywood, you should remember several general tips to work with this material. Drinking can only be done on dry material. Wet plywood has increased resistance, and when cutting, the veneer will begin to extend, which will lead to damage to the file or even the entire tool in the case of electric models. At the first signs that the teeth are not sharp enough or some part of the canvas is curved, the saw should be replaced.

When sawing plywood by an electrician, if possible, it is possible to place the main cut lines along the wn fibers.

This will contribute to the clean edges of the cuts. When working with a manual jigsaw, it is easier to lead a cut across the fibers. This will not protect from chips, but it will be less likely that the saw will pin the file or it will go along the scoop away from the intended line.

Before cutting a circle, you need to transfer its contours to the plywood. In this case, you need to try to ensure that areas with defects, chips, spots and knots get outside the cut out the cut out the cut. You can transfer the circuit to the plywood by circling it through copy paper by cutting a paper circuit for stroke or simply draw the desired radius circle. If necessary, the starting hole in the faner is made using a thin drill.

Today As An Electrician: Weird Pipe Bends

To cut a circle with a jigsaw, a canvas is inserted into the hole. The free end of the manual model is again fixed in its place using a clamp or fastener. The workpiece to the workbench is pressed by clamps, the cut is carried out according to the transferred line. When the circle closes, the central element is separated from the sheet and the edges are processed with sandpaper or file.

Before cutting out a jigsaw with an electric motor, you need to install a narrow file on it. There is a special improvement for this tool called a horror, it is installed in the center and starts work. When working on the tool should not be crushed, this does not contribute to a faster move. As a result of the pressure, a file of an electrician and even its fastening can break down and break down. If the circle that needs to be cut has a small radius, it is better to perform work in several approaches, since steep turns can break and bend the canvas.

Often, when repairing or installing various wooden products, you need to drill a perfectly round hole. In this article, we will try to illuminate all the methods that can cut out such a hole. Options will be considered using special tools, as well as without them.

A hacksaw with a very narrow canvas, a jigsaw, a drilling saw and a round file. these are the manual tools that can be sawed on a curve.

It is the narrow canvas that provides a hacksaw maneuverability, but for the same reason it is extremely difficult to lead. You must have a firm hand and an attentive eye to prevent deviations from marking. Do not try to work quickly. On the contrary, it is better to advance with small jerks. This will help to more confidently hold the handle of the saw and lead it exactly along a given line.

To cut small round or oval holes and “narrow” curves is better with the help of special tools. a drill saw and a round file, which also can be cleaned by rounding.

However, the most suitable tool for cutting rounded parts and holes should be recognized as an electronics. Its advantage is not only that the forces and time are saved. A set of interchangeable canvases with different teeth allows you to choose a canvas for sawing the blanks of almost any type, whether it be wood, plywood or wood-piece plate. In other words, electronics can be rightfully called a universal tool.

Cutting a circle in thick metal

In order to outline the exact contours of the figure that will be cut out of the metal, you should use the ruler, the marking circul and the marker.

At first, with the help. The necessary width of the circul connector is set so that it corresponds to the necessary diameter of the circle.

Then, on the metal plane, the central point of the circle is determined.

The contours are outlined from it with the help of a circul.

So that during the robots they are clearly visible, they should be drawn with a marker.

The use of a gas cutter

The circle in metal of medium thickness can be cut using a gas cutter. The work takes place in several stages:

  • The circuit circuit is planned.
  • The instrument burner is lit.
  • The burning torch is regulated.
  • Neatly and slowly with a torch is carried out according to the drawn drawing.

This method can cut a hole in the metal, which has about four or five millimeters.

Application of the welding machine

If there is no gas cutter in the home arsenal, you can use the welding machine.

It needs to be adjusted to the highest current level.

Then the burning arc is substituted to the contour and is held on it until the hole is formed.

Then you just need to slowly lead it in the drawing, until you get an even circle.

But the most important thing is to correctly adjust the tool power.

For example, if metal is used with a thickness of about four millimeters, you need a device operating at a power of about 150 amperes. If the metal is thicker. there will be more tool power.

To speed up the process. Better use thin electrodes. However, they quickly burn and need to replace. Because of this, there will be a need for frequent heating of the metal, since during the replacement of the electrode it will have time to cool down.

About how to cut a flat circle of metal with a cutter is shown at

Metal is the material for which the angular grinding machine was originally designed (corner grinder). Now, with its help, reinforcing rods, various metal sheets, pipes of various diameters, brick, concrete, stone, tiles and other building materials are cut. Due to the presence of a variety of nozzles, the angular grinder also allows you to polish and grind the surfaces of the products. Cutting metal with a corner grinder is one of the main, most common work. To reduce the likelihood of injury, it must necessarily be performed correctly, with strict compliance with the requirements of general and personal safety precautions.

The corner grinder refers to the category relative to dangerous power tools

You can get an injury from a scattering disk or a tool fell out of the hands. In both cases, the danger is associated with a high speed of rotation of the device electric motor.

To increase the efficiency of the corner grinding, expand its functionality, in practice use such Additional devices

Their use allows you to improve the quality of sawing of metal blanks, increase the accuracy of the process. The working conditions from the standpoint of security are also improving, its performance increases.

Using additional devices allows you to use the tool as a machine designed to perform different types of work.

To protect the cutting process as much as possible, work on metal with an angular grinding machine should be in compliance with a number of rules. They are conditionally divided into preparatory and main (workers) events.

Before cutting, it is necessary to carry out a number of manipulations.

If possible, the sawed material should first be fixed reliably, for example, in a vice to remove possible random movements. Hold the processed parts in the hands or is prohibited between the knees.

Drill saw

Neither manual nor electroplaw will help, if you need to cut a small one in the workpiece. with a diameter of less than 10 cm. hole. The jigsaw can also be useless if the workpiece is large. In this case, the most suitable tool is a drill saw. With her tip, she bites into a tree like a boiled and thus makes a “starting” hole for further sawing. Outwardly, the saw looks like a round file with the difference that its rod goes around the cutting edge in a spiral.

Burial saws are produced with interchangeable nozzles of various diameters, designed for wood processing, both soft and hardwood, as well as various materials from it.

The working organ of the drill saw is a metal rod with a cutting point, like a boumor, and a cutting edge that goes around the rod in a spiral.

This is what the narrowest of manual hacksaws look like. Thanks to the fasteners of the canvas in the hacksaw, you can change depending on the nature of the processed material.

Nozzle on the drill

One of the most popular and convenient options for cutting holes is a special nozzle for a drill. It is made in the form of a crest crest and has a rounded shape. With this nozzle, cutting holes occurs quickly, and they are quite even.

Nozzles are of different diameters, which allows you to cut the hole of the required diameter. If you have already prepared a hole, we can advise you to try yourself in optional trade.

Sverlo

You can cut a large hole and using a drill. To do this, it is necessary to mark the contour of the drilled hole in advance. Further, drill through the contour prepared in advance in a small drill. Further, with a jigsaw or a very sharp knife, cut off the holes, thereby connecting the holes. After which you can smooth out the circle with a skin of various grainness.

Chisel

You can cut the necessary hole in the same way with a chisel. Enough layer by layer to remove wood along the contour. This option is the least suitable for interior design. The hole should be even, which cannot be achieved by the use of improvised and unsuitable materials. The best option would be to use the crown on the drill. The hole is even and with smooth edges.

Thus, summarizing, it becomes clear that choosing a tool for cutting a hole is necessary based on your goals. If you need high.quality cut, then you can’t do without a special tool.

Any design, whether in your home, or in production, involves working with metal.

Often, during the operation of this material, the question may arise: how to cut a circle in ?

It deserves attention, since the complexity of the work process and the quality of its result directly depends on the choice of the right tool and technology.

Metal is thin, or thick and durable, so a variety of tools are used to cut it.

The choice of materials and cutting technology also depends on what diameter a circle is needed and how even it should be.

The use of a jigsaw

If there is a need for a perfectly even circle, you can use the electric to cut it.

  • First, the thickness of the metal is determined and the corresponding saw canvas is selected for an electric lobby.
  • Before cutting the circle in the metal with a jigsaw, the circuit circuit is planned on the working plane, which will be cut out.
  • Using a drill and a drill (in the diameter of the component from eight to ten millimeters), a hole is cut out from which work will begin.
  • The resulting gap is placed in the resulting gap and the cutting continues according to the intended.

Cutting using this tool does not take much time and effort. over, with the help of a jigsaw you can get a circle with perfect edges. But this tool is used only to work with the metal of the minimum or medium thickness (for example, 2. 3 mm).

The use of corner grinders

Corner grinder is used to work with metal of small thickness. A round hole can be formed with this tool, following such step.by.step tips:

  • Before cutting the circle in the metal of the corner grinder, marking is carried out so that its contours are clearly visible.
  • In the entire length of the scheduled drawing, short segments are cut out with a disk of corner grinder, which will ultimately combine.
  • The figure will be more similar to a multi.line than a circle. Therefore, after the end of the cutting, the product is processed and cleaned until the time, until the edges become quite even and smooth. For processing, you can also use an angular grinder. If the circle has a wide. You can sharpen the contours in a large disk.
circle, electrician, sheet, metal

When processing a cut circle with an angular grinder, you should be careful so that the disk is inside the hole and, at the same time, is located in the same plane with a working sheet.

How to cut a flat circle made of metal

How to cut a circle in metal: the best methods and valuable tips

circle, electrician, sheet, metal

Any design, for example, in your home, in production, involves working with metal.

Often, at one time of the operation of this material, the question may arise: how Cut the circle In metal?

It deserves attention, since the complexity of the process of performing the work is not the quality of its result does not directly depend on the choice of the correct tool.

Ways to cut a circle of thin metal

The metal is thin, as it is also called thick, not durable, a variety of tools are used to cut it.

The choice of materials from not cutting technology also depends on how much you can choose a studio, what diameter is needed a circle not how even he owes.

The use of a jigsaw

If there is a need for a perfectly even circle, use an electric jigsaw to cut it.

  • First, the thickness of the metal is determined by the corresponding saw canvas for an electric lobe is determined.
  • Ahead of time before cut the circle in the metal with a jigsaw, a circle circuit is planned on the working plane, which will be cut out.
  • By means of a drill is not a drill (in the diameter of the component from eight to ten millimeters) a hole is cut out from which work begins.
  • In the resulting slot, the saw blade is placed without cutting continues according to the planned drawing.

How to: Cutting steel trunking. containment UK electrician #shorts

Cutting with the use does not take away the long period not forces. In addition, by means of a jigsaw you will get a circle with perfect edges. Alas, this tool is used only for the metal of minimum or medium thickness (Two nettle. Three mm).

The use of corner grinders

Corner grinder is used when working with metal of small thickness. To form a round hole to form this tool, following such step.by.step tips:

  • Ahead of time before cut out Circle in metal corner grinding, marking is carried out so that its contours are clearly visible.
  • Short segments are cut through the entire length of the planned drawing, which will ultimately connect.
  • The figure will be more as a polyhedron than on a circle. Therefore, at the end of the cutting, the product is processed not cleaned until the time, until the edges are quite smooth not smooth. For processing, there is also an option to use an angular grinder. If the circle has a wide diameter, the contours are certainly a large disk.

How to cut a circle of corner grinding part 1

How to cut a corner grinder in a circle, without any adaptation photo in mine:.

When processing a cut circle using an angular grinder, you should be careful so that the disk is not inside the hole, despite this, is located in the same plane with a working sheet.

Cutting a circle in thick metal

In order to outline the exact contours of the figure that will be cut out of the metal, you should use the ruler, the marker is not a marker.

At first, using the ruler, the necessary width of the compass connector is set so that it corresponds to the required diameter of the circle.

Then, on the metal plane, the central point of the circle is determined.

The contours are outlined using the circul.

So that they are clearly visible in robots, they should be drawn with a marker.

The use of a gas cutter

The circle in metal of medium thickness is certainly cut using a gas cutter. The work goes in stages:

  • The circuit circuit is planned.
  • The instrument burner is lit.
  • The burning torch is regulated.
  • Neatly not slowly carried out by a torch on the drawn drawing.

This method is possible cut out a hole in the metal that has a width of about four in other words of five millimeters.

Application of the welding machine

If there is no gas cutter in the home arsenal, use the welding machine.

It needs to be adjusted to the very level of current.

Then the burning arc is substituted to the contour is not held by him until the hole is formed.

Then you just need to slowly lead it in the drawing, while it is impossible an even circle.

However, the most basic is to correctly adjust the tool power.

Nettle, if metal is used with a thickness of about four millimeters, you need a device operating on power about One ampere. In that case, the metal is thicker. the simply will not be the power of the tool.

To speed up the process of work, it is better to use thin electrodes. However, they quickly burn out do not need to replace. Due to this, there will be a need for frequent heating of the metal, since at one time he will have time to cool down the electrode.

What is really, how to cut a flat circle of metal with a cut, shown at

Highlight it do not press Ctrlenter to inform us.

How to cut a corner grinding of various materials

The corner grinding machine, which everyone calls the corner grinder, can not only grind, but also cut various materials using special circles. But in order to skillfully use these capabilities, you need to have knowledge and experience.

Many have a corner grinder, but most people do not know how to use it correctly and how to keep it. This leads not only to marriage in work, but also to severe injuries. Corner grinder is a rather dangerous power tool.

The circle should be installed by the pattern up and clamped by a special nut.

A person with the leading right hand holds an angular grinding of the handle with his right hand. In this case, the circle should be located on the left side of the machine, and the protective casing should close it on top. The rotation is so that during cutting sparks fly to a worker. If the corner grinder jams the circle and the corner grinder will break out of the hands, then it will not go to the cutter, but in the opposite direction.

The left hand holds the car by the handle, which is wrapped in a threaded hole on the case. There are somewhat for special cases of use, but the right position of the handle is only the upper.

Any design, whether in your home, or in production, involves working with metal.

Often, during the operation of this material, the question may arise: how to cut a circle in metal?

It deserves attention, since the complexity of the work process and the quality of its result directly depends on the choice of the right tool and technology.

How to cut a circle in metal as a corner grinder

How to cut a hole in the metal at home

In the metal, you can cut any holes exactly everything thanks to such modern cutting methods as plasma non.laser cutting metal.

Unfortunately, for home workshops, such high.precision equipment is a luxury if they have to use other methods, some where they are quite extraordinary.

Marking metal

The contour of the hole should be applied to the metal that should be cut. Cutting a round hole in the metal is not as difficult as drill a hole in the glass, but more troublesome. Marking is carried out using a marker, a ruler of a non.marking circul. For a hole consisting of straight lines, the markings are carried out by means of a line of not a marker. For marking a round hole, the circus is used. To make it better, it is more visible, it is provided with a marker.

Drill Crown

Drill equipment should include a nozzle-collar. With its help, you can make a hole in concrete, brick, artificial and natural stone, tiles.Nozzles differ from each other with cutting edges

Concrete crowns are equipped with special cutting elements.The diameter of the nozzle should be 68-70 mm, it is this size that has a divisor. For tiles, crowns with diamond spraying, carbide or winning. Carbido-wolframic, universal crowns are drilled holes in concrete and ceramic tiles.You can cut the holes under the outlet in the wall panel as a nozzle as for a tree, with teeth at the end.

The process of cutting the outlet hole is the same, regardless of the type of nozzle.The drill is converted into a drilling mode, the crown is applied to the mark on the wall or tile and the hole is drilled. At the time of drilling, the diamond line quickly heats up, so it is recommended to periodically moisten it in water.

A circular saw

Sometimes a circular saw is used for metal cutting. If you work with corrugated board, then the equipment must be included at low speeds. Otherwise, you can damage the polymer coating. For work you will need a partner who will hold the sheet. Among the advantages of this tool, one can highlight that the work is performed without heating, respectively, the protective coating on the profiled sheet you will not damage. It is best to use an aluminum circle.

To establish fast work with a circular saw, you need to prepare a pattern of plywood. The groove is not cut out in this sheet. This will be a kind of workpiece that allows you to save a galvanized or polymer coating on the sheet. An excellent tool for cutting metal is a two.disc saw. She, unlike corner grinders, leaves no torn edge and works much quieter. Unfortunately, not every master has a similar tool.

Crown for installing mounting boxes

The most common need to drill round holes in drywall is the installation of sockets. The invisible part of the outlet, a plastic round mounting box that is attached in the wall is called a socket. Distinguish between sockets for concrete, wood and drywall.

circle, electrician, sheet, metal

A drywall outlet is a plastic glass with adjustable plastic or metal plates. Thanks to these “paws”, the socket is fixed to the back of the drywall sheet. The depth of the mounting box can be 40, 50, 60 or 73 mm. As for the diameter, in a standard socket, this is usually 68-70 mm.

If you need to drill holes only for the installation of sockets, you will need only one crown. In this case, do not purchase a set of collapsed crowns. It is enough to buy one special crowned drill, with a diameter of 68 or 70 mm (depending on the size of your sockets).

To date, the diameter of the coronal drill on a plasterboard of 68 mm is the most popular sizes.

Properties of locksmith tools

The internal device of the electrolobian.

The jigsaw is intended for household and professional needs. The first species devices are small in power and are designed to carry out work in small volumes. The purpose of using special equipment is the professional orientation of the tool, its productivity and a long period of work.

Usually household appliances have a standard set of functions:

Electrician is used to finish surfaces, cutting out of uneven edges, openings of internal position, and furniture. The processed material is reliably fixed on the basis. Marks are made in advance, then the holes are cut. Roting vibrations of the shaft are converted into a progressive nature. The saw is fixed on the rod, its quality determines the period of use of the product. Choosing a device, preference should be given to round forms and thickened rods.

The jigsaw is distinguished by such positive qualities as:

Electrician external device diagram.

  • Cutting holes in any samples.
  • A simple device allows you to quickly replace the saw.
  • The ability to make a cut round or rectangular species.
  • Simplicity of use.
  • Does not require special knowledge and skills.
  • The presence of a significant number of saws with a different step border of action, the forms of the teeth allows for various types of work in the conditions of one device.
  • Reliable fixation of the sawn.out sample allows you to cut any distances from the edge of the product with a jigsaw.
  • The universal device allows you to drink to any depth.
  • At the time of work, the material is practically not damaged.
  • The shortened movement of the canvas provides a slowdown in the work of the device.
  • The possibility of injuries.
  • The probability of failure of the cord.
  • Checking the battery charging level.

Electrician has a system of built.in protection, pneumatics and electric drive.

The released new items are equipped with improved functions: reducing the number of vibrations, improving performance indicators, equipment of the device with convenient functions. Depending on the method of fixing the cutting part, there are saws:

A jigsaw in some way can replace a milling cutter, a hand hacksaw, a circular, a chain saw, a machine for grinding angles. The tool is necessary in any household, it allows you to carry out woodcarks.

The current entering the device from the network gives an impulse to the engine, setting it in motion. He, along with the gearbox, transfers the impulse to the gear, which fixes the stem. The circular action of the shaft is modified in motion of the working element of a reciprocal nature, moving up and down. Saws are fixed using screws or clamping mechanisms. Such fasteners help to change the canvases in a short time.

Rules for working with an electrician

To understand how to cut a circle in wood correctly, it is important to study the features of the workshop work. This carpentry tool helps to cut ovals, wave.shaped patterns, figures with uneven outlines, non.standard carved caskets, shelves with a through plan. In order for the interaction with the jigsaw to be organized and safe, it is important to adhere to the rules:

In order for the work with the jigsaw to go quickly and safely, do not forget to fix the product before work.

  • In order to avoid inconvenience, special stands should be prepared in the work. A slot is made to the middle of the backup, somewhat resembling a lock hole.
  • The stand is fixed with clamps or screws to the workbench.
  • At the time of work, you need to sit down, arrange the file strictly vertically relative to the floor and perpendicular to the surface.
  • The workpiece is placed in the middle of the stand, holding it with the left hand, with the right you can saw plywood. The location of the sawdust should be in the middle part of the hole of the background.
  • The tool does not tolerate strong pressure: a small touch and gradual movement up and down, and it will begin to work effectively.

Cutting a circle in thick metal

In order to outline the exact contours of the figure that will be cut out of the metal, you should use the ruler, the marking circul and the marker.

At first, with the help of a ruler, the necessary width of the compass of the circul is set so that it corresponds to the required diameter of the circle.

Then, on the metal plane, the central point of the circle is determined.

The contours are outlined from it with the help of a circul.

So that during the robots they are clearly visible, they should be drawn with a marker.

The use of a gas cutter

The circle in metal of medium thickness can be cut using a gas cutter. The work takes place in several stages:

  • The circuit circuit is planned.
  • The instrument burner is lit.
  • The burning torch is regulated.
  • Neatly and slowly with a torch is carried out according to the drawn drawing.

This method can cut a hole in the metal, which has a width of about four or five millimeters.

Application of the welding machine

If there is no gas cutter in the home arsenal, you can use the welding machine.

It needs to be adjusted to the highest current level.

Then the burning arc is substituted to the contour and is held on it until the hole is formed.

Then you just need to slowly lead it in the drawing, until you get an even circle.

But the most important thing is to correctly adjust the tool power.

For example, if metal is used with a thickness of about four millimeters, you need a device operating at a power of about 150 amperes. If the metal is thicker. there will be more tool power.

To speed up the process of work, it is better to use thin electrodes. However, they quickly burn and need to replace. Because of this, there will be a need for frequent heating of the metal, since during the replacement of the electrode it will have time to cool down.

About how to cut a flat circle of metal with a cutter is shown at

Noticed a mistake? Highlight it and click Ctrlenter to inform us.

How to cut a circle in metal with a gas cutter

Gas cutter is the best tool for cutting circles in metal. With this tool, you can work with both thin and thick blanks. This cutting method has the maximum performance and accuracy. We describe the technology.

  • Before cutting an even circle of metal using a gas cutter, mark the workpiece.
  • Light the burner.
  • Adjust the flame.
  • Slowly and gently cut the circle in the metal along the intended contour.

Фотография : резка металла газовым резаком

How to cut a circle of corner grinding. vdiweb.Ru

How to cut a circle in metal: the best methods are not valuable tips

At least what kind of design, for example, in your own house, differently in production, involves working with metal.

Often, at one time of operation of this material, the question may arise: how to cut a circle in metal?

He deserves attention, because the complexity of the process of performing work is not the quality of its result does not directly depend on the choice of the correct tool.

Ways to cut a circle of thin metal

Metal is narrow, or thick not strong, various tools are used to cut it down.

The choice of materials from not cutting technology also depends on the correct selection of the studio, what kind of diameter is a circle not as even it should.

The use of a jigsaw

If naturally the need for a completely even circle, use the electronic jigsaw to cut it.

  • At first, the thickness of the metal is not selected the corresponding saw canvas for the electronic jigsaw is determined.
  • In advance before cutting the circle in the metal with a jigsaw, a circle circuit is planned on the working plane, which will be cut out.
  • With the help of a drill is not a drill (in the diameter of the component from eight to 10 mm), a hole is cut out from which the work begins.
  • In the resulting slot, the saw blade is placed without cutting it lasts according to the planned drawing.

Rules for working with an electrician

To understand how to cut a circle in wood correctly, it is important to study the features. This carpentry tool helps to cut ovals, wave.shaped patterns, figures with uneven outlines, non.standard carved caskets, shelves with a through plan. In order for the interaction with the jigsaw to be organized and safe, it is important to adhere to the rules:

In order for the work with the jigsaw to go quickly and safely, do not forget to fix the product before work.

  • In order to avoid inconvenience, special stands should be prepared in the work. A slot is made to the middle of the backup, somewhat resembling a lock hole.
  • The stand is fixed with clamps or screws to the workbench.
  • At the time of work, you need to sit down, arrange the file strictly vertically relative to the floor and perpendicular to the surface.
  • The workpiece is placed in the middle of the stand, holding it with the left hand, with the right you can saw plywood. The location of the sawdust should be in the middle part of the hole of the background.
  • The tool does not tolerate strong pressure: a small touch and gradual movement up and down, and it will begin to work effectively.

Plywood (and to a lesser extent other sheet materials, such as a wood-piece plate or oriented-brown plate) has a significant decorative potential. If you have a fairly simple tool and certain skills, you can cut from plywood almost anything you want. But so that the details obtained as a result of such threads look quite presentable, the master should have several tricks in stock. It is about them that we will talk in our article.

Starting to work with sheet materials, many masters have only an idea of ​​how to perform a cut in a straight line. Therefore, the question of how to cut a flat circle from plywood can be at a standstill. Indeed, a regular or disk saw with the task of not managing. Figure sawing is most often made using such tools:

  • The simplest device that is used for cutting. With the help of a jigsaw, even the thinnest work can be done with your own hands, but for thick material or long cuts it is practically not suitable.
  • Electrics. Here you can use two varieties of devices: ordinary, with a vertically located file;
  • artistic, in which the steel canvas plays the role of the cutting element.

Ordinary electrician will be useful to you when working with Tolstoy. But if you are looking for a way how to cut letters from plywood or make other complex elements (for example, details of a children’s designer), then it is best to use a model with a strip saw.

Advice! Naturally, for each type of jigsaw there are several varieties of files and canvases. The correct choice of cutting element is a necessary condition for the high quality of the product.

  • In addition to jigsaws for curvilinear cut, you can use a furniture milling mill. Despite all the difficulty in managing, in terms of quality of the holes made, it many times surpasses most of the models of saws for plywood. With the help of a milling.

Also, do not forget about improvised devices, but we will talk about their use in the corresponding section.

Cutting from plywood has several nuances that the master must be taken into account:

  • Firstly, you can cut out only by dry material. High humidity leads to an increase in the resistance of plywood, therefore, with excessive effort, either the veneer begins or the saw will break.
  • You need to change the saw or cutting canvas immediately after the first signs appear that the teeth have swept.
  • If we cut out of plywood using an electrician, then to obtain cleaner edges the main cuts of the cut should be placed along the veneer fibers. But it is easier for hand files to work across the fiber: there will be slightly larger chips, but less the risk of pinching the file or its departure from the intended line.

Advice! Turning drawings for cutting from plywood to the workpiece, try to place the template so that the removed elements fall into areas with defects: knots, chips, spots, etc.D.

Why do you need a circle of plywood

Before you think about how to cut a circle in a faner. you need to clearly understand why it is needed. Both the resulting workpiece of a round shape and a plywood sheet with a hole of the correct shape can be used in the future.

Where a round blank of plywood can come in handy:

  • for the manufacture of various crafts and templates for them;
  • used as a basis for wall clocks;
  • applied for subsequent figure cutting or decoupage;
  • perform a stool seat, a countertop of a kitchen or coffee table, etc.D.
  • to create various souvenirs, for example, caskets, etc.D.

Also, cut the right circle of plywood may be necessary for the subsequent use of the sheet with the hole:

  • installations of a cut sink in the countertop;
  • obtaining a ceiling with a neckline for round lighting devices (spotlights or one chandelier);
  • for the production of furniture with decorative facades and other elements, etc.D.

When working with various types of wood, you always need to know the detailed variations of its processing. Before cutting a circle in a faner, you need to know all the options, because you often have to adapt to the situation. There are many options for performing such a venture, and they differ radically.

In order to cut a circle of plywood, you can use both professional tools and improvised means.

Electrical appliances or manual tools?

Determining the diameter of the future circle, it is necessary to take into account the dimensions of the working milling cutter.

The most popular option among all is an electrician. This tool allows you to cut not only circles, but also any other geometric shapes. The only minus is the need to form additional grooves in places of turns (angles), but when creating a circle, this is imperceptibly. It is very important to choose the right file, t.to. They are 3 types: tears on the left, tears on the right, tears from 2 sides. After the canvas is selected, cut the circle of any size.

Globzik ordinary manual. Before cutting a circle of plywood using this tool, you need to make sure that the work process is available. The main difficulty is a restriction (usually up to 30 cm) due to the physical structure, t.e. It won’t work in deep places. At the beginning of work, not from the edge, but directly from the center, the saw is refueled in the last turn.

Milling machine. A very convenient option, but requiring a rigid hitch with the surface, for which self.tapping screw is screwed into the center of the circle. A circle is made of any diameter, and very quickly. Sometimes there is not enough working handle, because of which all kinds of impromptu brackets have to be made, the role of which can be a channel, profile, bar, board and even a rope, but on a stiff coupling is much more convenient. This tool makes a fairly wide hole, so before starting work, you need to carefully conduct measurements of the future structure.

It is necessary to choose only sharp nails, and treat the edges of the resulting blank with large sandpaper paper.

Nails. A very popular way in cases where the work should be performed “already yesterday”, and the tools will not be soon. It is worth noting right away that the work eventually turns out rather rude, so it is used in the most extreme case. Only a hammer, 2 nails and a rope will be required. One nail is driven in the center of the hole, and the other is pulled on the rope for the required length (radius), after which a circle is carried out with a solid motion. Such circles with pressure continue until the circle is finally carved. At the very end, the nail is extracted from the hole, is turned over and carefully with a hammer is offered to achieve a more neat seam.

Strax and stationery knife. Everything is much easier here, because first you need to draw a circle (pencil), after which this circle is circled several times with a clerical knife under pressure. A feature of the stroke is the movement of not a knife, but a sheet of plywood, so as not to break the metal, and this action is repeated from 2 sides. Then a chisel is applied to the prepared seam and with non-strokes is brought to the opposite seam (2-3 strokes usually enough). At the very end with a hammer, a circle is knocked out, as in the version with nails.