How to cut a corner baguette without a chisel

How to cut a ceiling plinth: work with or without a tool

Any repair requires attention to the smallest details. On how well the finish is made, depends on the appearance of the room and its overall perception. To a greater extent, this applies to the ceilings, which in most cases are not perfect, so to hide all the imperfections (their and the walls), many owners use ceiling skirting boards, which give the rooms completeness. If the installation of baguettes in straight areas is not particularly difficult, the joints of the elements in the corners require maximum accuracy. Therefore, many owners who are planning, or have already begun repairs, are interested in how to cut the ceiling plinth, what tools can be used for this stage of the work.

The answer to the question of how to cut a ceiling plinth, depends on the material it is made of. Cutting is different, because the baguettes have different density. Therefore, the first thing to consider is the most popular materials, and at the same time the peculiarities of their cutting.

Styrofoam

Such products have the lowest price, because the material is very unstable to mechanical influences. Styrofoam is easily scratched, damaged by accidental impact. Pros. minimum weight, which simplifies gluing, easy processing, the ability to paint in any color.

This foam material consists of small granules, which are quite easy to separate from each other. However, they are the main disadvantage of such baguettes. They require a very sharp tool. Otherwise, the skirting may crumble, so it will be unsuitable for installation. This is true for both angular and straight cuts.

Styrofoam

This contender is more expensive, but it does not differ from the first candidate very much, since it is a “relative” of foam: it is produced from expanded polystyrene. This material also consists of small granule bubbles, but they stick together more densely. But Styrofoam will not tolerate a blade that is not too sharp, it will also crumble. Therefore, the craftsman needs to prepare no less than a sharp tool.

The main advantage of expanded polystyrene and polystyrene foam is their softness, which allows you to avoid gaps by pressing the workpieces tightly to each other and to the corners.

Extruded polystyrene foam

EPS is made from the same raw materials as conventional polystyrene foam, but in this case uses a different, more sophisticated technology. Ordinary EPS is produced using steam, which is run through the microgranules.

To obtain extruded polystyrene foam, the particles are mixed at high temperature and the same pressure, and then a foaming agent is added to the raw material. The size of the granules in this material is much smaller (maximum 0.2 mm), as a result it is less crumbly and more durable. you do not need a very sharp tool for its cutting, but bluntness of its cutting edge is not welcomed.

Polyvinyl chloride

Plastic skirting boards (PVC). another type of ceiling products. They are usually purchased for finishing bathrooms. If we consider the topic “How to cut a ceiling plinth”, in this case they are exceptions, because they use special, ready-made corners to dock them.

In general, these baguettes can be cut with a stationery knife, a metal hacksaw, or a sharp kitchen tool. As PVC products do not restore their shape due to the lack of elasticity, it is not recommended to put a lot of pressure when cutting them.

Polyurethane

This is another representative of polymer products. It is characterized by high density and lack of disadvantages of previous competitors. It is easy to cut, so the tool should be sharp, but there are no maximum requirements for its sharpening. Skirting boards of polyurethane do not crumble, no deformations, with the honor to bear almost any pressure.

Wood

This traditional material is cut with the usual carpentry tools: for example, a jigsaw, hand or electric. Work the places of the cut with sandpaper or a file. Since such products are more expensive than other baseboards, the work requires accuracy. A serious mistake can be made easily, but there is no way to fix it. The consequence of negligence will be the purchase of a new moulding.

An ideal tool for cutting wood would be an electric mitre saw. Its biggest disadvantage is the high price, especially of high-quality models. On the other hand, buyers have the opportunity to find an inexpensive tool that will do a decent job.

Tools used

First about how to cut a polymer or wooden ceiling plinth, how to do it correctly and quickly. In this case, 2 tools will be required for the work. a plier and a cutting tool.

What to cut baseboards with?

As for the latter, the choice depends on the material of the baseboard:

• Styrofoam products (all polystyrene) involve the use of a sharp office knife;
• Polyurethane baseboards are usually cut with a metal hacksaw;
• wood requires the “active” involvement of a jigsaw or saw.

The second potential tool for polyurethane is the same office knife. The reason is the rather low density of the material. Another alternative is a sharpened kitchen knife. A special requirement for it. not too thick a blade.

A metal hacksaw is a possible substitute for a wood jigsaw. The blade that has the smallest teeth is optimal. Otherwise, the tool will get stuck in the material, and in such conditions it is extremely difficult to make a flawless cut.

Chisel and its self-made

The chisel is the second indispensable tool for working with baseboards.

What is it?

Not everyone may know what it is. This is a device that allows you to cut any workpiece at different angles (45-90°). It is a groove, consisting of the bottom and two sides, in which slots are made for tools. At the bottom of it lay the material, and in the slots are inserted a hacksaw (knife, etc. д.). After sawing the baguettes with it you get almost perfect blanks.

The mortar is a necessity for trimming any skirting boards, as a 45° angle is required for the joints of the elements. Otherwise, the connection of the parts will not work: or there will be a gap between the adjacent skirting boards, or they will simply need to be trimmed again, because it will be impossible to join the adjacent products.

Yes, the remaining hole can be masked with some kind of compound. However, this option is still not the best. The filler may soon change color a little, and this discrepancy will become very noticeable. However, even here there is an exception.

How to make a chisel?

To make it yourself will need to find a board length of about a meter or more, or a sheet of plywood (chipboard). You still need to prepare:

• From the selected material cut 3 parts with a width of 200 to 250 mm, their length. 300 mm (400, 500 mm). With the help of self-tapping screws they are connected in the shape of the letter “U”.
• Using a protractor, make marks on the upper parts of the sides, corresponding to an angle of 45 ° (if necessary, and 90 °).
• Then a hacksaw is used to saw the holes through so that the grooves reach to the bottom of the tool.

Drill the prepared holes with a rasp, so that a jigsaw or a hacksaw can easily enter them.

Baseboard planking plier: basic rules for use

Everyone will be able to understand how to cut the corners of the ceiling plinth. For the process to go smoothly, you should familiarize yourself in advance with the main ways to create beautiful and even billets.

The main rule of work is to observe the slope of the angles. If the baseboard is fixed to the right, the corner will be cut from the left side, and vice versa.

The plane is a handy tool for fast workpiece processing

Polyurethane ceiling plinth: what is it, advantages and disadvantages, what it consists of, what kinds there are, how to choose, step by step installation of the baguette, coloring, restoration methods, average cost. in our publication.

What is a plier, how to use this tool

Beginning repairs in the apartment, many people wonder how to cut the corners of the baseboard on the ceiling. It is important to familiarize yourself with the rules for using the equipment. Chisel is a device consisting of walls with side cuts and the bottom. The part that needs to be processed is laid in the middle and corrected with a file.

The main question. with what to cut a plinth plastic. The result should be a perfectly even angle of 45 degrees. Sawing the fillet is fast and easy if you use a ready-made saw, or make it from available materials. The tool for reliability is placed on the floor and held by the left hand. The hacksaw should be positioned in one of the oblique lines, depending on whether the corner should turn out. right or left.

For beginners it is best to fasten the tool to the table, so it will not come off during work

• pencil to draw a thin, barely visible line for the trimmer;
• Tack put the side of the tape in the jig and determine the angle of the cut;
• Hacksaw should pass exactly along the marked line;
• The second fillet is turned and cut from the other side, so that the angle formed when combining the two parts.

Before gluing it to the ceiling, the tack should be sanded down.

Stucco from polyurethane: what is it, what are the advantages and disadvantages, the main types, composition, manufacturers, the main selection criteria, the stages of independent installation, options for use with photos and cost.

How to make a chair by yourself?

If you want, the jigsaw can be made and at home. It can be made of wood or iron. The size of the workpiece does not play a special role, but the wider it is, the more accurate your cuts will be. However, if the width will be greater than the length of the hacksaw, which you will cut skirting boards or boards, it will be extremely inconvenient to saw, so do not take too wide a workpiece.

First, a transverse straight line is marked in the center of the workpiece. Then at a distance of 1/2 the width of the workpiece from the intersections of straight lines with the edges of the workpiece are made marks. Then these marks are connected crosswise, as shown in the picture.

Wooden chair fastened with self-tapping screws

Next begins the process of marking the side walls of the jigsaw. Place them on the already marked out base and make marks, referring to the marking of the base. Then draw straight lines from these marks across the entire wall.

Then begin the process of assembling the jigsaw. The walls should be attached to the base with screws, if the device will be made of wood or particle board, or with corners and bolts, if it is made of steel. Only after installation, saw cuts are made in the jigsaw.

Making a Wooden Chisel

There are two ways you can make a wooden tool:

• First option. Prepare three pieces of wooden boards. If they were not at hand, you can use slats made of wood or plywood. Use a hammer and nails to hammer a U-shaped figure out of the boards. On the sides of the resulting product are marked the corners necessary for the work and make cuts along them. The result is a semblance of a jig in which holes are made with a hacksaw. The skirting boards are inserted into them and trimmed.
• The second variant. It is a combination of a paper template and a tree. You will need two boards or strips. From them, a figure in the form of a corner is assembled. A line equal to the angle of the cut at 45 or 90 degrees is drawn on the cotton canvas. Before you make a corner from the ceiling plinth, you can draw any angle. in this feature and there is an advantage of a homemade tool before purchased ready-made device. The skirting board is placed against the jig and pressed with the left hand. The template is placed in the place where the cut will be, and cut the baseboard, according to the line drawn on the paper.

There is another way to replace the store floor joiner. It does not involve making a tool from either wood or paper. To do this, you will only need to take any objects that form a corner. For example, it could be a wooden countertop. Before trimming the baseboard, you should carefully take measurements. To outline the corner of the fillet, which is located inside, the length should be measured from it.

There are nuances in how to make the outside corner of the ceiling skirting. in this case, for its wording should be guided by the fact that the tack will protrude into the room at a distance equal to the width of the product. In accordance with all the described calculations and make the marking of the baseboard lines.

In case of failure, you should not despair, because you can always redo the work with mistakes by filling the empty space with putty. When the ceiling plinths with corners will be installed in their places, the ceiling will get a neat and finished look.

Cutting corners without a chisel

Not everyone has the opportunity to buy professional cutting tools. Yes, and the expediency of such a purchase is rarely justified, as spending money on a jig that will be used only once is not the best solution. It is possible to cut the skirting boards without it. There are several alternative ways to make the right corners.

Manual preparation of the template

The first and most common variant of trimming the fillets without the use of a jig is based on the use of a paper stencil. To implement this method you will need to prepare the following tools and materials:

Important! To create a simple blank, it is necessary to use thick paper. An excellent solution is the use of cardboard. From it, a template is cut out, on which the cutting will be performed.

We enclose the skirting board on a cardboard blank and cut it with a hacksaw. Some masters perform marking on the product itself. In this case there is no need to use a template.

The second option is to make the cutting tool yourself. For this you will need to prepare three boards that have the same dimensions (50×15 cm). Next, it is necessary to dock them together. The two side boards, which are the walls, should be fixed to the transverse board at right angles. In the next step, it is necessary to mark an angle of 45 degrees on the walls. The necessary measurements can be taken with a simple square. Ready-made tool will allow for a short period of time to formalize all the corners in the room.

The third method involves the use of improvised means. In this case there is no need to design a template. It can be replaced by an ordinary table, which will need to be moved to the wall. To the corner formed in this way, it is necessary to attach the fillet, and then conduct its marking. In the end, the part is cut with a hacksaw or a construction knife.

Cutting an indirect angle

Not always the walls have a perfectly flat surface. In this case, the installation of ceiling plinths is very difficult, because few people know what to do in such a situation. The most preferred solution to cope with such a problem is to mark the corner on the spot.

For marking you will need to prepare an ordinary pencil. Before you start, it is recommended to read the video, which describes the nuances of trimming the baseboards. The first step is to apply the skirting board to two walls (one at a time). Along its edge it is necessary to run a line for the trimmer, which is marked on the ceiling. The point that corresponds to the intersection of the lines is marked with a pencil.

At the end you need to connect the point with the bottom edge of the fillet. Next, trimming is made. During the work, it is recommended to use a ruler. If the work was performed correctly, the resulting corner will repeat the relief of the wall.

In order to cut the right corner of the ceiling plinth with your own hands, it is not necessary to use a professional tool. There are other ways that do not require anything complicated from the master. The most important thing in such work is the correct marking. Before you start cutting, you must make sure that you are doing everything properly.

What recommendations on cutting the corners of ceiling plinths can you give?

Skirting boards. fillets

To do it correctly, it is important to strictly follow the existing recommendations and rules of finishing works. And then the result will please you.

In the attachment of the fillet (so called this element) there are no difficulties: virtually all varieties of products are attached to a reliable glue.

In order to hang a ceiling plinth, even inexperienced repairmen have no difficulty. Worries them quite another thing: how to properly trim a ceiling plinth? Virtually every room, no matter how intricately shaped, is equipped with corners.

And in these internal corners of the individual elements of the skirting board must be nicely and evenly docked. And in rooms of especially complex configuration will have to fiddle over the outer corners. Let’s try to figure out how to be in each of these situations, and how to cut the right part with the available tools.

Baseboard materials and cutting methods

First of all, let’s try to determine what can be used to make a fillet, and what particular material is better to cut.

On sale today you can find products made of foam (polyvinyl chloride), wood, polystyrene foam and polyurethane.

Perhaps some of the cheapest are baseboards made of foam plastic, which is a fragile, soft and brittle material.

Even the fingers of the hand can leave dents on them, they are easy to form creases and defects. It is difficult to cut a nice and even corner of a PVC baseboard.

Inexperienced craftsmen can go to waste because of this reason. Also, this polymer has high electrostatic properties, which explains its ability to collect dust.

It is best to cut this type of plinth with a hacksaw or a sharp construction knife.

Styrofoam products are also inexpensive, although this material is more durable analog of the traditional foam.

They can also be cut with a sharp tool.

Extruded polystyrene foam

Skirting boards made of extruded polystyrene foam are a bit more expensive, they are somewhat denser and more difficult to cut. But they are much less likely to crumble and break.

Therefore, it is more convenient and easier to cut them. For this purpose it is convenient to use a hacksaw or a sharp knife.

Polyurethane skirting boards for the ceiling are currently probably one of the most expensive.

But they justify their cost: moisture-resistant, quite strong and dense, quite elastic.

Located over the kitchen stove baseboard can warp and even crack a little.

They are perfectly cut with a special knife, without forming a crumb. But these products are very sensitive to temperature differences.

Wooden skirting boards for the ceiling. it is quite heavy and dense products, hard and durable.

They are well amenable to processing with a special fine-toothed hacksaw. You can also use a reliable metal blade. So how to trim a ceiling plinth correctly?

Prefabricated corners

Note that every craftsman has the opportunity not to pore over the exact cut and fit corners.

In a construction store you can buy a factory-made corner piece, in which you can easily insert the prepared edges of the skirting board.

It is sufficient to measure the required length of the workpiece, and cut it at right angles.

All defects and imperfections will be hidden by this special element. But such a convenient way to use is not always possible, because the standard sizes of such factory corners can differ markedly from the size of the baseboard itself.

These corners will stand out for their disproportionality, and it will not look very neat. But if the design of the room and the size of workpieces allow you to use this method, you should not neglect it.

Trimming a fillet

Trimming with a power drill

How to evenly trim the corner of the ceiling plinth with it?

The chisel is an uncomplicated tool used by carpenters. It can be used to cut any workpiece at the desired angle.

It is usually a wooden, metal or plastic tray, which is made for cutting at an angle of 45 ° and 90 ° special vertical slots.

There are complicated designs, which in addition to the named corners also have a hole to make a 60-degree cut.

A special plane is available for professional work. Its swivel mechanism allows you to fix the cutting blade in relation to the workpiece at any given angle.

Inner corner

The prepared skirting board is put against the ceiling and the required length is marked off.

Then this same plank is inserted into the joiner exactly as it will be positioned on the ceiling. This must be pressed against the far wall of the machine. Hold the skirting board in this position with the left hand.

The blade of the hacksaw should be in such a position, so that its angle is 45 degrees, and the handle is as close as possible to the hand. Trying to avoid exerting pressure on the saw, we carefully cut the workpiece.

Next, the skirting board must be cut off a mating strip. It is also placed at the far wall of the tool, held and pressed, this time with the right hand.

A similar position to the previous procedure for the hacksaw. its handle is brought closer to the hand at an angle of 45 degrees. The skirting board is cut.

Then the finished, already cut slats are docked together. the accuracy of fit is checked. It is believed that for better orientation, when making the inner corner, it is better to start cutting from the front of the product. Places of cuts usually need to be adjusted with a file.

Outside corner

The correct way to observe the dimensions more accurately is to begin by marking the inner corner first, and only then move on to the outer one.

Otherwise, it may be that the entire length of the plank is not enough.

The strip is attached to the ceiling, the size made marks. Holding the ceiling plinth with the left hand, the ceiling plinth is pressed against the nearest wall, the handle of the hacksaw is close to the hand. The workpiece is cut.

The counter strip is pressed against the nearest wall, holding it with the right hand. The blade of the hacksaw should be at an angle of 45 °, the handle of the tool is close to the hand of the master. A piece of the workpiece is cut off, and the corner is accurately joined.

Such processing edge details with mash is good if the angle between the walls is flat and straight (90 °).

If its performance leaves much to be desired, then it is worth using a different method.

Marking on the ceiling

The method with the marking on the ceiling allows you to cut a corner exactly and straight. It has one disadvantage. it is quite inconvenient to hold the baseboard plank by weight during the procedure.

In all other respects with this method you will be able to mark the angle for cutting even more accurately than other methods.

When the skirting board is applied to the intended place of installation, all size deviations and inaccuracies are noticeable and immediately taken into account.

Cutting a corner

First take a pair of blanks, then cut them at right angles. With the end of the slat against a perpendicular wall, we put one slat. We draw a trimmer line on the ceiling along the contour of the baseboard. We remove the first slat, then, in the same way, pointing at the end of the wall, we put the counter slat. Exactly the same way we mark the contour of the line for the trimmer.

The intersection point of two separate lines is the mark at which to cut the workpiece. Each plank is placed against the surface again, and the point of the future cut is marked on both of them. From the found point to the other edge of the baseboard slat draw a trimmer line. Baseboards cut to the previously made marks, neatly connect, place in the place of their installation.

This method allows for more accurate processing internal corners.

Ways

There are two of the most common methods of correctly, easily and comfortably cut perfect corners for baseboards. The first involves the purchase of a special scratch saw with a large number of notches on its perimeter, which help cut the corner correctly and evenly. The second option. it is the cutting of corners without the help of a jigsaw, about it today and we will talk. This process for beginners is quite difficult and laborious, in addition, the presence of a pitching rod does not guarantee 100% relief from this work, be prepared for the fact that the first time you may not succeed.

There are several ways to create corner joints without the help of a jigsaw.

One of them is to apply the markings directly on the ceiling. First we will need two pieces of baguette, cut at an angle of 90 degrees. It is not necessary to take two-meter bars at once and try to cut them, you can cut two pieces of 15-20 cm for easier holding them with one hand in the position you need. Further we put them in the next order to the ceiling and spend a 5-centimeter line for a trimmer on the ceiling to the end of a baguette, tightly pressing a skirting board. After to an opposite corner we put the second molding, and we do the similar action, and in a place of an intersection of a baguette and earlier made line we do a neat notch with a pencil on a baguette. Repeat the same with the second skirting board, making a similar notch at the intersection of the baguette and the drawn line.

Now we can cut the molding at the desired angle, to do this, use a construction knife or a hacksaw, depending on the material from which the skirting boards are made (below we will tell you what materials are used to make moldings, and how best to cut them). To cut the corner correctly, place the baseboard on a table or chair, and make a cut from the point you marked on the ceiling to the opposite corner of the baseboard. After that you can safely join the corners and glue. It is necessary to consider that this method is suitable for adjusting only internal corners, it will not work for adjusting the outer corners.

The second way is to trace a sheet of paper or plywood under the chair, to do this you need to draw two parallel lines, then from one line to perpendicular to the other, so we will get the markings for the right angle. For the marking under 45 degrees you should use a clerical triangle or a protractor, passing through the perpendicular two lines under 45 degrees relatively to the parallel lines. Then, as with the plinth joiner, we put our skirting board along the line and trim it to the necessary angle.

The third way. is to make a primitive crosscut with their own hands, which will not become less effective. To do this, take three planks or slats and knock them down in the shape of the letter “U”, make slits at right angles and two slits under 45 degrees. This way you will cut corners without the “help” of a chair.

The fourth method is quite rare and inventive. it consists of intricacies with heavy paper or cardboard and a small bar. For this bend a sheet of cardboard at the desired angle you want, take a small bar, which will serve you as a template for trimming the corner. Press the prepared piece of cardboard against it, hold a knife or hacksaw strictly vertically and carefully cut the block at the desired angle. To trim the baseboard, simply place the plank on top of the baseboard, press down firmly and cut along the cut line of the plank.

The fifth way is to buy special fittings with ready-made ceiling corners: internal and external. Unfortunately, there are many variations in the design of the baseboard, special inserts may not be found under your baseboard. But generally very convenient for those who do not want to engage in sawing corner joints.

But also if your home corners are irregular, then prefabricated blanks or a wire cutter will not help you. Because there are only 45, 60, and 90 degree joints you can cut. In that case, cut the edge of the baguette by eye at an angle of 45 degrees, and trying on your corner, carefully trim it, so you can achieve a nearly perfect connection, with only one thing. there may be a lot of such trimming and trimming.

How to properly cut corners at the ceiling plinth. How to cut a corner with a power drill

In rooms with even corners and walls, cutting ceiling skirting boards with a wire cutter is usually not very difficult. The tool looks like a U-shaped trough with saw guides made at 90 and 45 degrees. Placed inside the device required to cut the element, insert the saw into the guides. In the process of cutting baguette should be firmly held in place, to avoid defects. It is rather difficult to cut the skirting board, as it is necessary to achieve its simultaneous adjacency to two planes. If the width of the baguette is small, it is more convenient to press it to the near side. ” How to cut ceiling baseboards. tools and cutting rules “.

How to cut the corner of the ceiling plinth, if the outer corner is decorated:

• Before you cut the corners of the ceiling plinth with a wire cutter, a 45 degree angle file is made.
• The chair is set in a comfortable position. This will make it possible to determine the exact location of the baseboard: first of all, this applies to the edge of the product, which will be adjacent to the ceiling. To avoid confusion, it is most convenient to place the right-side plank on the right, and the left-side. on the left.
• The surface is pressed against the bottom surface of the chair. In this case, the second part is lifted, being the closest. It should be so put on the wall with a jig so as to avoid its wobbling during the work. In this arrangement, the front side of the product is turned to the opposite side.
• It is necessary to make a cut at an angle of 45 degrees from yourself. If done correctly, folding the two halves results in a nice outside corner.

Once the correct sawing of the ceiling plinth in the corners is completed, both pieces should first be attached to the ceiling “dry” to check the geometry of the match corner. If necessary, adjustments are made by trimming with a knife. Small gaps are easier to cover with putty, which, after drying, must be processed with sandpaper. As for the inner corner, it is much easier to make.

The procedure how to cut the ceiling plinth in the corners of the interior type is much like the above described. The first thing to do is to determine the side that will be adjacent to the ceiling. It is laid on the bottom of the jigsaw. The reverse side is leaned against the near wall. After the sawing of the plinth on the ceiling is finished, the obtained fragments should be dryly attached to the corner, checking the quality of the junction. If necessary, it is adjusted. After that the installation of one and the second skirting board on the mounting compound. Small gaps in the corner can be filled with a special putty.

Different materials and their special features

The most durable material compared to the other two listed below, the merits of which are hardness, impact resistance and the ability to withstand certain mechanical loads. However, wooden skirting boards (another name. tacks), glued to the ceiling, is also relatively easy to handle. they can be cut (for this purpose, a wood hacksaw), to cover with varnish. Wood will add warmth to the interior. Of the disadvantages can be called a higher cost than that of foam. However, the appearance of wooden fillets retain longer than that of foam plastic.

Styrofoam. Perhaps this material is the most unstable. it is not resistant to mechanical damage, scratches and even minor impacts. Of the pluses. light weight, the ability to paint in different colors and ease of handling (it can be cut with a stationery knife. but very carefully).

Styrofoam. This material can be considered a kind of foam, although its strength characteristics are somewhat higher (extruded polystyrene foam is more dense than foam plastic). As for processing. styrofoam is also easy to cut with a regular sharp knife, and also has a small weight, which is an important factor when taking into account the load on the walls.

Step by step instruction

When installing a ceiling plinth first you need to prepare the surface before pasting skirting boards, it must be grinded from minor irregularities, then you must primer the adhesive places to create maximum adhesion between the adhesive and the wall or ceiling. Primer is suitable for the same as that used for gluing wallpaper or ceiling tiles.

Before gluing it is recommended to take a small piece of baguette and practice cutting the corners, so as not to spoil unnecessary.

So, you are all prepared, and it’s time to start the process of cutting corners. To create an inside corner, the first of the above methods will work great for you. If you have a flat wall, you can cut off equal pieces from the baguettes, and from them cut corner joints, then just glued them accurately at the stop long strips. These manipulations will facilitate your work when trimming and prevent the baguette from bending or breaking.

If the walls have imperfections, and you are worried that the place of gluing will then be visible, you can adjust the corner on the floor, and then glue.

When cutting the outer corner, remember that the inner corner rests against the wall, and the outer corner, on the contrary, protrudes over it. Similar to the method described in the first method, you can try. The only difference will be that the output of the baseboard outside the wall is needed to the width of your baguette trim. After trimming strips at the correct angle and joining them, you may need to adjust the angle by hand, since the corners of our homes are often not nearly 90 degrees. The rest of the methods we described will allow you to make the outer corner more easily. Just as with the inside corner, it is better to practice first. this will make your work easier and reduce the skirting waste.

Before gluing the skirting boards, you need to make sure that the connections fit exactly. Modern mounting adhesives seize very quickly, so you have almost no time to fix a mistake, and tearing off the baseboard. and the possibility of breaking it, and the need to re-clean the surface of the skirting and the wall of the glue. It is better to remove excess glue immediately with a small clean rag or sponge so that no traces are left.

With proper patience and proper trimming you can achieve a “seamless” joint, and your baguette will look solid, which will simplify its further painting and eliminate the need to use finishing putty to smooth out the joining seams.

Some useful tips to facilitate the work and its preparation

Here’s how to choose the right tool for your corner trimming. This section also contains useful information on how to join baseboard segments in corners.

Choosing a corner forming tool

The most economical option is to buy a simple plastic chisel. It is a plastic block with eight working slots. This tool is designed for only two operations: 45-degree, 90-degree, and 22.5-degree trimming. The angle of 90 degrees is useful, for example, if you need to cut into the middle of the molding jack.

Some attachments come with an eccentric retainer. They are preferred, because it is easier to work with it. the skirting board is clamped in the right position and does not move in the process of cutting. Accordingly, even if mistakes happen, they are minimal, and adjusting the angle will not be difficult.

What to cut plastic skirting boards with: a simple plastic diagonal jointing jig

If you have to make repairs in your own home, it might make sense to buy a more serious tool. a one-plane rotary plier. It is designed to cut at an angle of 15, 22.5, 30, 36, 45 and 90 degrees. The design of such a jigsaw includes 2 clamps. for clamping in the horizontal and vertical planes, as well as a limiter, which allows you to trim the workpieces to the same length. The hacksaw will be built in here. If you do not understand how to cut a ceiling plinth. the video review below will help you.

How to cut a skirting board in the corner: a rotating diagonal plane

How to file a ceiling molding contains a detailed description of the rotary jigsaw, and information on how to use this tool.

This will come in handy in your work

As you noticed, the text mentioned marking with insulating tape. This is the most convenient way to mark blanks, as a pencil is not always visible on the floor plinth, and with the ceiling plinth its lines are sometimes difficult to reconcile. Bright same pieces of tape very well visible, and when they disappear need to remove just one movement of the hand. Traces of glue after removal of such marks do not remain.

What is the best skirting board??

Before you can properly cut corners on the ceiling skirting, you need to get it right.

Tip: The ceiling skirting board will look harmonious if its width is chosen correctly. The higher the walls, the wider the baseboard should be.

The most durable, moisture-resistant and elastic are polyurethane tacks and it is not very easy to cut a corner of such a ceiling plinth. However, all these positive qualities “overlap” one major drawback. they do not withstand sharp temperature fluctuations, which does not allow their use in all rooms.

For example, in the kitchen, where there is a gas or electric stove, polyurethane baseboards will retain their original appearance for about a week. After that, with frequent cooking, when the hot air will be then raised to the ceiling, then lowered, they will begin to deform, spoiling the whole “picture”.

Skirting boards made of other materials also have their disadvantages.

For example, products made of polyvinyl chloride have an increased electrostatic conductivity and if during the work on their surface appear dents, it will be impossible to remove them. With the slightest mechanical impact, polystyrene and polystyrene ceiling plinths break.

If we talk about what kind of ceiling plinth for stretch or conventional ceilings is better, the exact answer is probably impossible. Since each of them has its own positive and negative qualities. Therefore, all the same, you have to make a choice, depending on the financial resources at your disposal, and on the conditions under which the tack will be used.

Types of ceiling decorative plinths

Before you start installing baseboards, you need to buy them, and to do this, you should have information about the range of these products.

Baseboards are made of different materials, namely:

To have an idea of each type of decorative ceiling elements and choose the right product, you must have at least their brief characteristics:

• Baseboards made of PVC, have a reasonable price, but this material has the ability to accumulate static electricity.
• Polyurethane molding is distinguished by its high quality, durability, moisture resistance and elasticity. Its main disadvantage is insufficient resistance to sharp temperature drops, and for this reason polyurethane products should not be installed in rooms with high humidity.
• Wooden fillets are subject to high temperatures, moisture, and weight.
• Baseboards made of polystyrene are characterized by moisture resistance, good quality and attractive appearance, but they break under mechanical stress.

In addition, the baseboards differ in other parameters. width, length, relief and shape. Their use in rooms of different sizes depends on these characteristics.

For example, wide products look harmoniously in high rooms. There are nuances in how to cut wide ceiling plinths. The matter is that these profiles are joined at an angle of 90 degrees. To make a precise cut, you use a wire cutter. But when the corners of the room deviate from the standards, the work is done manually.