How to cut a gas -pile stump correctly. Gross work on a private site

How to cut a chain.fingered tree: sawing technology

Valka of a chainsaw trees requires a strictly observing safety regulations from the performer.

• use the corresponding working uniform. To do this, wear dense fabric clothes, protective glasses and gloves, as well as shoes with nonsense sole. Many experts also advise using Berushi, but in practice they do more harm than benefits. Often because of them, the dwarf does not hear the creak of a falling tree, which is why he does not have time to run away from him at a safe distance;
• check in advance, pull and sharpen the chain. In a properly stretched headset, the guides of the teeth will not jump out of the grooves when the chain is pulled from the upper part of the tire;
• Do not blame the tree in strong winds. it can change the trajectory when the trunk falls.

Before you bring down the trees with a chainsaw, you need to calculate the places of their fall in advance. In order not to damage nearby objects, large branches need to be cut off the barrel. It will also be necessary to clean the territory next to the tree. To do this, you need to clear the shrub, and remove all the necessary tools from the area. As a result, the territory around the tree should be completely cleaned, so that during its fall, the downshire can freely leave it.

Another important point. there should not be power lines near the tree. If they are, and the tree needs to be urgently tapped, then before work it will be necessary to clean the other side of the barrel that is located next to the wires. The contact of the latter with the branches should be completely excluded.

To blame the tree with a chainsaw, you should act in this order:

• First you will need to make the first cut. Its depth should be about 1/4 of the total diameter of the barrel. The incision itself should be located approximately at the level of the roller belt, and delve into the barrel at an angle of 45 degrees;
• Then you need to make a lower cut. It should be located at the level of the knees of the roller, and go horizontally to the place where both cuts will be connected. As a result, the roller should get one continuous incision located at an angle of 45 degrees. In this case, the tree should not be completely cut, otherwise the operator will not be able to predict the direction of the fall of the barrel;
• At the finish stage, you need to make a gross drink. Immediately before that you should make sure that there are no people or animals nearby. The last cut should be done from the side opposite to the direction of falling. It should be located about five centimeters from the previously made lower cut, strictly parallel to the last.

The main thing when cutting is attentive and speed. You should carefully choose the scraps of the cut to ensure the optimal trajectory of the fall of the tree. As soon as the barrel begins to fall, you will need to immediately extract a chainsaw from it, drown out its motor and run away as far as possible.

Flone a tree

When all the cuts and bags are made, it is time to start directly to the roll of the tree. We strongly recommend doing this together or three (depending on the size of the tree). The person who finished making should be made to the side and gives a signal to assistants. Those on the command pull the ropes and try to tie the tree into the intended area.

Naturally, if the tree does not give in, you can push the barrel with your hands or deepen the cut.

If the tree is thin, and you can cope with it yourself, it is still desirable to use the rope for insurance. To tie a tree on the principle of a lever, pushing it with a thick stick at a height of 3-4 m from the side of the gross drinking.

Manual shorting

A fairly laborious process consisting of many stages. Despite the fact that for its implementation you will not need heavy equipment, it is worth enlisting many auxiliary tools. The process occurs in the 3rd stage:

• The first stage is to dig the comel and the root system. With the help of a shovel, scrap or picks around the stump, the volume of the earth is removed sufficient to remove it. The roots should be exposed. Performing this operation alone can take a long time.
• The second stage is the collapse of the roots carried out using an ax at the highest possible distance from a comel. In the process, the roots vibrate, because of which the actual force of the ax of the ax may be much less than the expected. Then you can resort to cutting them through a chainsaw or hacksaw.
• At the last stage, the stump is pulled out by means of scrap, jack, winches, tali or tractor. Do not forget about the stumps of the roots that go separately.

It is worth considering that if the tree is quite large (from 30 cm in diameter) and heavy, it is impossible to endure it on its own. For loading and export, you will have to use a tractor or manipulator. Also, the stump can be burned, but a lot of time will take this action, up to several years for complete destruction.

Mechanized backing

This method requires much less effort and time. To do this, you will need an excavator, hinged devices or any chopper. This method of combating stumps will be more effective not only in comparison with independent rooting, but even with the work of the brigade that digs out a manually.

Nevertheless, mechanized wrinkling is more expensive than manual. Not every farm will find the necessary equipment, therefore, first of all, it will have to be invested in it. In the case of rental, it is worth making sure that the type of equipment you have chosen is suitable for the territory where work will be carried out. For example, the use of a wheeled excavator or tracked technique is excluded in areas with a garden or landscape design due to an overwhelming.weight of a huge weight of tools.

What laws regulate stump burning?

Even in cases where the stump is located on a section that is in private ownership, when it is burned, the following laws and regulatory documents must be taken into account:

• Article 11 of the Federal Environmental Protection Law “from 10.01.2002 N 7-ФЗ-citizens are entitled to a favorable environment and clean air if the burning of the stump is carried out in violation of the established norms and rules, then a fine is due to this.
• Clause 218 of the Rules of the Field of the Federation. Open Fire can only be used in accordance with certain requirements, most of which are set out in this document describes the procedure and rules for using open fire, including security measures.

The main problem when burning stumps is not associated with a ban on bonfires, but with the need to observe safety precautions.

Safety precautions are reduced to the following requirements:

• The height of the fire shaft (the rules are talking about digging a hole for burning garbage, but since the stump cannot be lowered below, it is necessary to cover it with a firewall) 30 or more see.
• The minimum distance to any buildings 50 m, to deciduous forest 30 m, to coniferous 100 m.
• A plot with a radius of 10 m around the stump should be cleaned of dry grass and any branches, and dig the perimeter of the circle or sprinkled with non.combustible substances.
• Keep funds at hand to extinguish a fire, that is, water, sand and fire extinguishers.

Despite the fact that the law does not oblige to warn the neighbors about breeding fire, we recommend that they do not open windows or doors during the burning of the stump and do not feel discomfort due to smoke.

In addition, we recommend visiting the nearest Ministry of Emergencies and inform them of the time of burning stump. The Ministry of Emergencies will be able to check the correctness of the implementation of preparatory measures and give permission to breed fire.

In case of receipt of official permission, control organizations will not be able to make claims.

Types of burning

There are three main ways to burn stumps that differ in purpose and execution:

Superficial

For him, the stump is covered with firewood and a fowline, then set on fire. As a result, only the aboveground part and a little underground part are burned.

This method of burning is not suitable for combating bacteria and combating sprouts from the remains of roots. The main condition for the complete combustion of stump is the use of firewood whose diameter is not inferior to the diameter of the stump near the ground.

Active combustion time is 2-5 hours, then another 5-10 hours remains the danger of fire from burning coals.

Complete

To burn the stump in the ground, they dig a hole around it to free the roots, which are then chopped off and used as fuel. For the complete combustion of such stumps, it is necessary to put firewood into the pit, the size of which is no less than the size of the stump in the lowest part.

The combustion time is the same as that of the previous method of burning, and the danger of fire from coals remains 10-15 hours.

Chemical

This method allows you to burn even deep roots without digging them. To do this, lay selitra or urea in the stump and leave for 1-2 years so that the reagent is poured out of the wood.

You will find the method of impregnation and the number of reagents in this article. After impregnation, the stump is set on fire using a small amount of kindling. The combustion time is 30–90 minutes, after the end of burning there is no danger of fire, because the wood completely burns, leaving no coal.

How can you cut a tree

Corner grinder is used as a universal tool with which you can solve a variety of problems. The corner grinder is cut everything: metal, concrete, ceramics and so on. Is it possible to cut a tree with a corner grinder?

Arguments against

This tool was not intended for wood files, and its design is not optimized to perform this task. What does this mean in practical terms?

• The woods are soft, and the disk of corner grinder can stall in it. As a result, a corner grinder is able to practically fly out of your hands, and where specifically it will fly. no one will predict. It is possible that specifically in you.
• When working on wood, a disk of corner grinder is very overheating. What else can you saw full.bodied bricks? 4641 22 than cutting a tree close to the wall ? As a result, he loses his strength characteristics, becomes fragile and brittle. In such criteria, the smallest skew or excessive pressing can lead to the destruction of the disk. How can you cut bricks- Mastergrad forum. And the disk that has been raised at large speeds is approximately the same as Shrapnel.
• There are no specialized wheels for wood saws for Bulgarians (if only the Chinese standard). “Craftsmen” use non.core wheels or try to adjust the disc from the circular saw. Due to the high speed of the corner grinder, both approaches can be regarded as complete ignoring safety precautions with all the ensuing consequences.

For corner grinding mash (corner grinding). Bosch Carbide Multi Wheel. 2 608 623 013. A small test.

? yet

You can cut a tree with a corner grinder, but at your own peril and risk. If this is a one.time operation, then the desire to use an improvised tool is clear. But even in this case, it is easier and safer to get a normal knife on wood anywhere.

If the need to work on wood often arises or the scale of the task is great, then it is advisable to purchase a specialized tool. Great option. electrician.

That, at all without options?

A way how to saw a corner grinding tree, and not risk your own health, is. Many are worried about the question: how to cut a tree correctly? The tree can be cut using an electric and manual saw. It only consists in the corner grinder to remake under the circular saw.

This involves a hard tool mount on a bed with guides. The processed material according to the guides is supplied to the corner grinder in the same way as the circular saw. Similarly, you can make a pendulum saw from an angular grinder.

In both cases, the use of the sawing disk is supposed to. Naturally, when working with such a tool, all possible protective equipment should be used.

But this method also has a number of obvious shortcomings:

• Technical complexity;
• The corner grinder is still not a circular saw. they have a different speed speed and power;
• This approach does not eliminate the risk of disk destruction from overheating;
• Start button on corner grinding, and the material must be served through the guides from the other side. That is, you will need to either squeeze the start, which is dangerous or working together.

Theoretically, it is possible to cut a tree with a corner grinder, but it is strongly not recommended. This is a gross violation of safety precautions, and is fraught with serious injuries. Even the corner grinder does not have complete universality, so it is better to use a profile tool.

What to consider when rolling trees near the house

To blame the vegetation, including large.breasters, growing around the houses is quite difficult. Such an event involves a special technology. The following factors may indicate the need for logging:

• The stem part is located more than 45 degrees;
• The plant has a high and thin barrel;
• there are cracks and hollows or rotten areas.

Located at a close distance of the building and structures, electrical communications and engineering networks often very limit the area of ​​work. In this case, the roll is most often given to the entire roll, but in parts, through suspension and lowering of already sawn elements. This option implies the mandatory attraction of special equipment or binding and the descent of cut fragments using a nearby trees.

After cutting, a stump remains, which is most often removed by means of a stroke, which allows high.quality alignment of the soil surface on the site. To reduce labor costs for such events, it is recommended to fill up the trees, hitting the roots. Such a henchman is not performed directly, but at an angle to the direction of growth of the root. You need to dig out the roots with a shovel, having previously removed the bark from the upper part of the roots and surrounding the soil, which will reduce the risk of an ax during the cutting process.

Valka of trees using an ax and a conventional saw has been used recently less and less, due to the presence of electric and chainsaw owners of suburban real estate. Nevertheless, in particularly difficult cases, it is advisable to seek help from specialists who, using special equipment, perform such work very quickly and as efficiently as possible.

Basil when possessing proper power can cut off any tree trunk, which is enough for the length of the cutting part. It is necessary to carry out the work very carefully, adhering to all the rules

Particular attention should be shown when there is a risk of unpleasant situations due to too thick, icy or contaminated wooden array. It is necessary to take into account all the factors that can complicate the work and use the chainsaw neatly, constantly monitoring their actions and the work of partners. In the article we’ll talk about how to cut a chainsaw tree correctly. scheme and instructions

In the article we’ll talk about how to cut a chainsaw tree correctly. scheme and instructions.

How to saw branches

We proceed to sawing branches, and you need to do this only when the barrel is lying on the ground in a horizontal position. The lower branches that rest against the ground due to the severity of the fallen wood need to be cut at the very end. The process of proper sawing of the branches of the chainsaw has the following view:

• You need to start work from the bottom of the barrel, moving to the top
• When all the branches are removed, you need to make the cut of the barrel on top
• After that, the saw must be drowned, leaving inside the barrel
• Drive the wedge into the hole to avoid biting the tool
• Perform further finishing

For proper sawing of the barrel, you need to start from the beginning of the crown of the tree. In order not to jam the tire of the tool, always work, observing the instructions. Often, even experienced sawmills are faced with the fact that the saw jams between the two trunks. In this case, you do not need to try to free it by fidgeting and twitting on yourself. this is how you can break the tool. Drown out the saw, find the support to slightly raise one part, and free the tire of the tool. It is problematic to do this without a partner, so never work in the forest yourself.

How to blame a tree in the right direction?

Any specialist knows that to bring large and young trees are completely different works. But there are nuances that must be taken into account in both situations.

How to blame trees in the right direction?

A size equal to half the diameter of the tree is required. It can be done from the side of the inclination, or on the other side on which you want to “put” a massive tree;

Creation of a cut from the opposite side, followed by a roll;

In a collision with large trees, it is necessary to make an inclined upper cut. Be sure to take into account the cut angle. 60 degrees. With the cut of the stem part, 1 is enough?4 parts of the diameter;

It is necessary to make a lower cut in a horizontal form. Sprinkled converges with the upper cut. Thus, we will have a side log house;

We go to the second horizontal file (it is above the previous one). Sprinkled is done strictly on the other side;

In the 2nd cut, you need to insert a wedge. As soon as finished, we take the scapula and fall the tree.

The best time for such work is the period from November to December. In these months there is no large amount of snow, but the earth is already frozen. When working with a chainsaw, you need to keep it strictly with two hands, without leaning on a tree with a second hand!

How to blame a tree if at home?

If you are a beginner, perform work on a roll of trees (especially large ones) near the nearest houses is not recommended. There are many factors related to such a roll of trees.

The tilt of the stem part should not be allowed less than 45 degrees;

The plant will have both thin and high barrel;

There may be rotten areas, cracks, hollows, which can be visually seen.

If there are many houses, engineering networks, communications next to the tree, then for work we will have very little space (otherwise something can be offended). Therefore, experts in such circumstances prefer to blame trees in parts. That is, the element is cut, suspended, then descends. Without special equipment and professionalism, such works should not be done! The descent of the sawn parts of the tree occurs using other trees located nearby. they are needed to bind fragments of wood.

What to do with stump?

To eliminate it, as a rule, a feeding is used. Thus, it will be possible to get rid of the stump without “digging up” the soil and leave an even earthen surface. To take less time and effort to the roll of trees, it is recommended to handle roots. The procedure is carried out at an angle and strictly to the direction of growth of the root. To quickly dig the roots, use a shovel. But from the visible part of the roots you need to remove the bark. It is advisable to stand the soil, otherwise it will be difficult to work with an ax, since it will become dull.

Today it is extremely rare to use a classic saw, an ax for such work. Since with the help of electrical equipment the rolls of trees can be carried out much faster. With compressed deadlines, you should contact specialists. Since the work is performed promptly and as efficiently as possible can only be with special equipment and skills to work with such equipment.

How to cut a tree on chocks correctly

It is much easier to cut the trunk of a fallen tree than to cut down the tree in the bud, but there is a certain risk here. For example, incorrect cutting of trees can lead to a tire in the trunk and then you will have to use a jack or lift the barrel with crowbar, which will take a lot of effort and time. In order to avoid such situations, it is necessary to evaluate the position of the barrel in advance and first cut it in those places where there is stress.

It is better to cut the barrel from the crown, gradually moving towards the comal.

The cut can be both upper and lower. The upper cut is performed until the barrel begins to fall and squeeze the tire, after that, if possible, it is necessary to finish the barrel from the bottom. If there is no possibility, then a few more are made next to the first ree, as long as the tire stops squeezing.

After the barrel is cut into several large parts that can be rolled, they are sawn into flasks with the upper ree.

Safety precautions

In order for the cutting of the tree to be safe, the following rules must be followed:

• Use shoes on thick ribbed soles. it will provide more reliable adhesion to the ground and wood barrel, and will also allow you to confidently stand on the stairs or any protrusions.
• Use a suitable shirt or jacket with long fastening sleeves and not too tightly tight.fitting pants that are tucked into boots or tied in the manner of sleeves. Starting to work, it is necessary to fasten clothes for all the buttons and make sure that nothing dangles anywhere, otherwise it can tighten it under the chain of the chainsaw, which will lead to severe injuries.
• When working with a chainsaw, it is necessary to put on protective glasses or a transparent shield, thanks to which unsuccessful chips or sawdust will not fall into the eyes.
• On the eve and during the cutting, do not take narcotic, psychotropic or alcohol.containing drugs, because they slow down the reaction and violate the coordination of movements. In addition, many of them reduce adequacy, therefore, under their influence, it is difficult to correctly assess the condition of the tree and choose the right method.
• Do not proceed to work, if there is at least a slight malaise, because reactions slow down in this state, and attention is scattered.
• When cutting branches, it is necessary to stand so as not to be on a cut.off area. Before cutting off a branch or piece of the barrel, it is necessary to calculate the trajectory of the segment several times, and take a safe place on the ground in advance.
• If you need to move up, then insurance must be fixed in two places. This will allow even when transferring the insurance point to a higher area not to remain without protection.
• Regardless of the complexity of the roll of wood, you cannot do this work alone. In case of injury or some kind of emergency development of the situation, Partner will be able to provide first aid or call for help.
• If the wind speed exceeds 2 m/s, then you can not blame large trees, if it exceeds 5 m/s, then you can not carry out any work related to the rise to a height. At the speed of wind of 8 or more m/s, you can not cut down even small trees.
• You can not cut down trees during a weather change or with rain. In the first case, there is a great probability of the sudden appearance of gusts of wind, and in the second, the soil and the surface of the tree become more slippery.
• You can not perform any work in the dark, because it is necessary to clearly see both the overall picture and each separate detail.
• Before cutting, it is necessary to notify everyone who lives in houses next to the place of work, so that none of them accidentally find themselves in a dangerous zone.
• You can not use a chain with a dumb chain, it is especially dangerous to unilateral damage to the chain. In this case, the tool will not be cut directly, but deviating towards more sharp teeth. with a high degree of probability, this will change the direction of the fall of the branch or barrel, as well as their behavior at the time of the separation.

Where to put cut branches and trunks?

After removing the tree, there are branches and trunk or pieces of the barrel, which must somehow be disposed of.

Here are the most popular recycling methods:

• Burning is ineffective and often illegal, so you can get a fine. We recommend carefully reading articles (burning of foliage) and (burning stumps), in which there is information about the requirements of the legislation regarding the use of open fire in their sections.
• Making firewood. even a rotten tree can be cut and fraught with firewood. Despite the fact that they will be less effective than fuel from healthy wood, for some time they will be able to drown a house or cottage, so it will be possible to save a little good firewood.
• The manufacture of chips is one of the most universal methods of disposal, because a lot of useful things can be made from the chip. Read more about the use and manufacture of this material here.
• Take out to the landfill. for the tree you will have to cut into the pieces convenient for loading, as well as pay for the services of the landfill, on which the solid waste is disposed of. Sometimes branches and trunks are taken to spontaneous landfills that pollute the landscape and pose a serious threat to nature. In addition, there the wood will quickly turn into combustible material, and there will be even small fire to be enough to get a large fire.
• Make poles and poles. cut branches and pieces of trunks are well suited for the manufacture of pillars and poles, which can then be used in the garden. From them you can make greenhouses, trellises for growing vegetables or fence. Also, from them you can make the frame of the walls of turntables.
• Crafts. branches and pieces of the barrel are well suited for the manufacture of crafts and home.made furniture. In this article, we talked about how to make crafts from stumps and roots, but in the same way you can process other parts of the tree.

What is a stump, and what does it interfere?

PNI is the remains of trees that appear after cutting down or as a result of a barrel fracture under the influence of external factors, such as wind, car pressure, etc. D.

When the tree trunk falls, a stump remains in the ground, which consists of aboveground and underground parts.

The aboveground part is the widest fragment of the barrel, turning into comel (underground part). It consists of the same wood as the barrel, therefore, has the same properties. The comel differs from the upper part in that the fibers in it are located not evenly (vertically), but go to the sides, forming the roots.

The aboveground part of the stump is covered with bark, while the underground is almost completely devoid of it. The shape of the roots depends on the type of root system, and the thickness is on the age of wood.

Root systems are the following types:

In the blasphemer root system, the roots are thin, directed in different directions, as well as up or down, so that the tree effectively opposes even strong winds.

Rod root system.These are one or more powerful vertical roots that go back 2-10 meters.

The surface root system consists of long horizontal roots lying at a small depth.

Stumps interfere with construction and agricultural work. In addition, the surface roots even after removing the barrel absorb water-in winter it can freeze, which will occur frosty soil flowering that can damage the foundation and walls.

During plowing, superficial roots can damage not only a plow or a harrow, but also a tractor. And if the tree was cut down during the sanitary cutting caused by pests living in wood, then the comel and roots will be potential forklines of diseases.

When clearing the territory under the landing of cultivated trees, it is necessary not only to dump/cut off old plants, but also maximally extract stumps and roots from the ground, which in the spring can give a new shoot.

Given the high survivability of wild trees, this must be done before the seedlings are planted, because after fighting the shoots it will be very difficult.

Rooting methods on the site

All feeding methods can be conditionally divided by the degree of complexity into:

In addition, they can be divided by impact on stump/roots, that is:

Manual

With manual shorting, the comel and the root system are digging, then the roots are chopped off and the stump is pulled from the pit with:

The main advantage of manual shorting is that all work can be done without attracting heavy equipment. To dig a hole, one or more workers with shovels are needed, on solid or dry soils, picks may be required. Then the roots are cut off at a maximum distance from the comel, using axes for this.

Unwaster workers can not always cope with this, because the roots vibrate, which is why the shock effect of the ax is noticeably less than the expected.

In such cases, the roots can be cut with a hacksaw or chainsaw. You will find a more detailed description of this background method here.

To some extent, manual shorting can be attributed:

These methods also do not require attracting heavy equipment, so they can be carried out by several people.

Chemical destruction

With the help of various reagents, you can both kill the root system (it will slowly rot), preventing this by the appearance of a new shoot, and completely destroy the roots along with pests or pathogens living in them.

Preparatory measures are the same for any active substance. in the aboveground part of the hemp, holes are drilled into which the reagents are filled up and a small amount of water is added.

Then the holes are covered with a cork of wood, clay or plasticine and left for 1-2 years.

Below we have listed substances that are most often used for chemical destruction of stumps:

• ammonia or potassium nitrate (impregnates wood, making it very fuel);
• urea (kills, then loosening the wood);
• iron or copper sulfate, as well as table salt (kill wood, as well as all pests and pathogens of diseases located in it).

After the reaction ended, the wood impregnated with the nitrate is set on fire, and it burns even underground.

Wood residues impregnated with sulfate, urea or salt can either be burned, having previously digged the roots as much as possible, or crushed with the help of a chopper of stumps. To obtain more information, we recommend reading this article.

Burning

Preparations for burning are carried out in the same way as for manual shorting, that is, the comel and roots are dug, then the remains of the tree are laid down and set fire to.

As a result of burning, most pathogens and pests living in wood and roots die, but this effect does not apply to deep and long horizontal roots.

Therefore, to combat pests, it is better to use other methods. In addition, using this method, it is necessary to comply with the requirements of various regulatory acts regulating the application of open fire.

over, even in cases where the burned stump is located on a private territory, because the spread of smoke and a high risk of fire do not depend on the form of ownership. You will find more detailed information about these regulatory documents, as well as the procedure when burning stumps here.

Growing mushrooms

This method is used in cases where there is no need to completely remove the roots from the ground, and for the destruction of the stump can be spent several years.

The mycelium penetrates even the most distant roots, extracting not only nutrients from them, but also lignin, so wood becomes loose.

Когда грибница извлечет из древесины все питательные вещества (об этом говорит прекращение плодоношения), старые пень можно убрать, разрушив его легкими ударами как молотка, так и ботинка, после чего перекопать вместе с землей.

After all, even after growing mushrooms, there are many substances necessary for the regeneration of the soil in it. You can read about this in more detail here.

Explosion

Exligence is used when laying roads through the forest, as well as in cases where for any reason it is impossible to use heavy equipment, and manual shorting takes too much time.

The advantage of explosive shorting is that you can simultaneously blow up many stumps, cleansing large spaces.

After the explosion, the territory is cleaned with the help of a gatherer’s gather. The disadvantage of this method is in the need to involve a professional explosive technology that has admission to storage and use of explosives.

Mechanized

Removing or destruction of stump using mechanisms does not require such physical effort as manually, and also takes much less time.

Thanks to this, one vehicle with the necessary equipment will be more effective than a team of workers who struck the stump manually. Mechanical rooting can be attributed to the digging excavator and loosening using hinged devices.

This type also includes the effects of various crushers (grinders), which can be divided into 3 types:

The main disadvantages of any mechanized backing is dependence on good roads and the ability to bring equipment to the place of work.

In addition, you first need to seriously invest in equipment, including attachments, which is why the cost of such services is quite high.

The launch of the chainsaw

Before the starting procedure, the fuel mixture and grease for the metal circuit should first be poured into the corresponding compartments. Check the tension of the circuit, if necessary, tighten it. After that, you need to put the chainsaw on an even, stable surface, at a certain distance from the dressing site (for fire safety purposes). Then you should take the front handle with the left hand, and put the right leg on the back.

Then you need to press the ignition button, put forward a throttle and twine several times by the starter handle. When the chainsaw motor gives out a flash, the throttle is pushed back, and the starter handle, on the contrary, is pulled out to the maximum. This movement must be repeated until the engine starts.

The next step: you need to turn off the chain brake and press the gas several times so that the chainsaw is warming up. Also, the master should check the supply of lubrication to the chain. To do this, the saw must be brought to a clean paper sheet. The appearance of an oil spot on the sheet will mean that everything is in order and lubrication is enough.

If the chainsaw has already worked for a certain time and was simply drowned out, then its launch is carried out according to a simplified algorithm. that is, only the starter handle is used, and you do not need to touch the throttle.

Tool care and its maintenance

The master, among other things, should also properly care for his chainsaw. After each use of its use, the remaining fuel must be drained into a separate container, and the tool itself is cleaned of sawdust and garbage.

Check the tension of the chain of the chainsaw is also necessary constantly. Such a check is simply carried out. you just need to pull the upper medium links. If the chain is with some effort, then it is stretched normally.

The condition of the chain itself, tires and leading stars also need to be controlled. You can use only a chain with sharpened sharp teeth. It is necessary to monitor the level of pollution of the air filter (if it is too contaminated, this will lead to problems with the start).

The owner who provides high.quality leave for the chainsaw, undoubtedly extends her service life.