How to cut a stretch ceiling under the LED tape. Installation of the plinth

options for installing light and soaring lines in a stretch ceiling.

Light lines in suspended ceilings at present, called in the trend. It is no longer enough for many to glue the LED tape around the perimeter and get the original backlight in the form of a soaring ceiling.

I would like some variety in design and the presence of flooding light not only around the edges, but also throughout the area of ​​the room.

When using a sufficiently powerful LED tape, you can get a full, uniform lighting of a room without a chandelier and any other lamps on the ceiling.

We will not consider some complex figured constructions, to create which requires appropriate experience and dexterity.

Consider the simplest options for light lines that you can perform yourself.

For example, one or more soaring lines from wall to wall, dividing the ceiling into sectors.

Either the second option is separate segments of the lines in the middle of the stretch fabric that do not reach the walls at all.

In this case, you will leave less material, and the installation itself will be much easier. The functionality of the lighting will not suffer at all.

Such simple linear constructions are ideal for independent installation of luminous ceilings.

How does work begin? First of all, it is required to find the lowest point on the ceiling, taking into account the presence of air ducts, cable channels, distribution station, etc.P.

Next, measure the wall profile along the perimeter of the wall, on which the main canvas will be pulled.

At the bends and corners, carefully cut it and form the appropriate blanks in size and geometry of your room.

Apply the profile to the wall and first fix it on a painting tape. Check the horizon on the laser level, drill holes for the dowel.

Score them and fasten them around the perimeter of the baguette.

After all these works, in a normal situation, one could pull the canvas. But do not forget that we will have light lines in the middle of the ceiling.

Therefore, they need to prepare the appropriate profile for them and, if necessary, embedded.

To the main ceiling, the profile is attached to the oeinated corners.

It is not advisable to use suspensions, as they are unlikely to be able to ensure sufficient hardness of the structure.

If your canvas is quite large, then you can use wooden bars as mortgages. The design will be more reliable.

The light fishing line for a trimmer itself is assembled on a special profile, which has a fixation of the harpoon of the canvas on both sides.

There are many options, here are the main manufacturers and varieties.

Used only under a stretch ceiling. There is a problem with the creation of complex design and figure drawings.

The light transformation element here is the stretch ceiling itself.

This manufacturer is widely used PF 3645 or PF 6838.

With it, the ceiling is easy to divide into sectors, or create rectangular structures.

You can choose a narrow or wide version for two tapes.

Disadvantage. it is quite problematic to make a high.quality light segment in the middle of the ceiling. It is mainly used for installation from wall to wall.

On its basis, you can collect four types of product:

He jokes with all other profiles in a lightweight. At the same time, the screws in it are screwed into the technological cavity and are not in the visible zone of lighting.

how to fix the LED tape. to the ceiling, in the kitchen in the headset, to drywall.

After you have determined what type of LED tape you will use for your backlight, mounted the wires to connect it, the following important question arises. but how to secure it securely.

Let us consider in detail the five main methods and frequent errors made in this case.

Taping manufacturers, as a rule, have provided one of the most common ways. installation on the adhesive layer located on the reverse side. It is hidden under the protective shell and to get to it, just pick up the tip with a knife and pull off the protective film.

Roughly speaking, there is already a double.sided tape. On one side, it is glued to the tape itself, and the other, you stick it on the corresponding surface of the ceiling, walls, kitchen cabinet.

The surface can be either smooth or even or rough. Due to its flexibility, the tape should stand normally on any of them, whether it is a convex arch or other elaborate figures.

If you doubt reliability, then just apply a little varnish or paint to the plane. They leve all the base as they should.

If you did not guess with the trajectory or highlight and began to tear it off, then the second time to glue it on the same layer, you will not succeed. Therefore, always first mark the markings.

And if the tape has already been peeled off or it must be removed and transferred to another place, what to do? Then use the second method. additional double.sided tape.

It is better of course to first apply it in the right place, and only then, glue used it or a new tape to it.

It would seem, why come up with something else, if there are already such simple methods provided for by manufacturers. However, as practice shows, after not quite long time, the backlight fixed by this method begins to fall off and peel off.

Before gluing on any surface, it must be correctly prepared:

You need to do this a few minutes before the direct installation. Only after that one can hope that the backlight will sag for a long time and will not fall off.

The second point is the quality of adhesive tape. Choose specimens that have a snake icon on the back.

This is the most famous world brand that produces not only adhesive tape. Even the Scotch brand itself is just a small part of the company.

At the same time, the presence of such a sign does not guarantee that you will come across a quality product. To fake and write only two letters, for Chinese craftsmen it is not difficult.

In addition, always pay attention to the date of manufacture. Even high.quality specimens from eminent brands (Philips), having spent several years in cold rooms, can easily lose their original properties.

And you will puzzle your head, it seems to be a “sn”, and for some reason it is poorly glued.

What to do to an ordinary user and is there a more reliable way to mount LED strips? Of course there are, and most of the installers and electricians have long been using it for a long time.

It consists in the use of ordinary superglines. Thanks to him, your tape will be fixed reliably and will not disappear, even when the service life of the LEDs comes out and they will lose their brightness.

It is best to use glue in the form of gel.

It would seem, as such a small bubble can be enough for a few meters? Secret in installation technology.

For reliable contact, it is not necessary to apply glue over the entire surface at all, it is enough to evenly put the drops every 5-10 cm and all. The rest of the work will be done by factory tape.

The glue is applied to the surface itself.

Why this cannot be done, read below, where installation errors will be considered.

These are the two most simple, reliable and inexpensive methods of installation and fixing LED tape from all available. However, it is suitable primarily for small power models, such as SMD 3528 or SMD 5050 to 14W/m.

They can be fixed directly on the wall with wallpaper, ceiling or wooden base of lockers.

With heat dispersion of 6 to 10W, the surrounding air calmly copes. But from 14W, there is already more significant heating and an aluminum profile will be required here, acting as a cooling radiator.

Methods of lighting with LED ribbon

Two methods are distinguished: installation under the canvas of a stretch ceiling coating and above it.

Backlight mounted in a specialized box.

In the first case, they create a box of drywall, it is mounted on the wall, the tape is attached to the lower wall of the box, which goes parallel to the base ceiling. The width of this zone reaches half a meter, and the height is twenty centimeters.

White satin stretch ceiling with stars #Shorts

In order for the diodes to shine exclusively on the PVC film, a narrow-size bar is attached to the inner lower wall of the box, which closes the LED-extension. It is located parallel to the wall. Directly above the ribbon with diodes, a canvas made of PVC is mounted. The result is a tension two.level ceiling, where the canvas is illuminated from below. The first level of the ceiling with LED backlight is the canvas. The second level is a drywall box where the LED tape is located.

A distinctive feature of LED lighting is that the backlight extends exclusively to the edges of the stretch ceiling. The center with such installation remains dark, but if necessary, the tape can be installed above it, and the diodes in this situation are fixed on the main ceiling surface and shine from above.

LED tape allows you to create a variety of figures, to emphasize the geometric forms of the ceiling. Due to this, the design of the room changes.

Installation of the LED lighting device directly for the ceiling

In addition to the first option, there is also the possibility of fastening the LED tape directly to the walls, but the ceiling canvas should be partially transparent.

Methods differ only in the place of fastening of the tape with diodes, and the principles of organization are similar.

Choosing a tape with LEDs

White and colored ribbons are presented on the market. The former decorates and emphasize the interior design, but the best option is the use of blocks with colored diodes, which you need to choose depending on the mood.

Broad.free use in the design of the ceiling has found such tapes as SMD 3528, SMD 5050. The first option is smaller, with one crystal in Diode. The second is longer, with three crystals.

Important parameters when choosing: The density of the location of the diodes per 1 linear meter and their power.

Совет! Не приобретайте мощные светодиодные ленты, так как возникнет риск перегрева. Особенно если монтаж осуществляется над натяжным потолком. Это обусловлено тем, что воздушные массы над полотном PVC будут чрезмерно горячими, что провоцирует риск перегрева ленты, блока и сгорание диодов.

The ribbon with diodes requires low voltage, which is 12.24, 36 and 64 volts. The power supply is required such that can provide low power. Pay attention to its power. In the block, it should be 25% higher than in all ribbons.

Nuances

Check out some nuances so that there are no difficulties.

  • Before starting installation, calculate all the cost of work if you plan to invite specialists to do the work. So you can make sure that the savings will be significant if you do everything yourself.
  • After the protective layer is removed, gluing should be carried out quickly. Do not forget that before this you need to fully prepare the surface so that it is clean and without any defects.
  • When cutting the profile pieces, this must be done in specially marked places.
  • When you connect the power supply, follow the polarity. If you use a connector, then it has all the necessary designations.

It doesn’t matter which installation option you choose, the main thing is that you observe the sequence. With a competent approach, you will get chic lighting under the ceiling coating.

Installation recommendations

When installing the LED tape on the ceiling, there are some important points, subject to which you can make both the result and the process better and more pleasant.

Translucent stretch ceiling with backlit installation

  • For installation for the ceiling, you must have a project, t.e. You need to think through all the details before the purchase of all the necessary components.
  • Installation is carried out using Velcro. Please note that the sticky layer should be located on the back of the tape and protected by a special film. Before starting installation, select the suitable for the slopes of the pvc corner. It is attached to a poverty with small screws. This is done due to the fact that a sticky strip will be peeled off from drywall, and the final fixation is fixed to PVC. This is especially true for suspended ceilings, since the design will have to be removed further with a small repair.
  • Sold the wires with all caution, since the material is the basics of plastic, and the LEDs themselves poorly experience overheating. For this purpose, a special flip paste is best suited. Regarding the solder itself, he was able to prove the form of the PO-61. It is very important that the melting temperature does not exceed 160 degrees. If you have small experience in melting small details, trust this to a professional. it will be more reliable.
  • We do not recommend connecting more than 3 meters of tape together. In a large mass, the conductive path is not always able to withstand a large voltage, and for this reason the section, which is more than 3 meters in length, attach other wires to the controller.
  • If the installation of the LED tape on the ceiling is carried out with your own hand, be sure to follow the polarity of the wires.
  • Cutting and pruning the tape should be carried out along certain lines, which, for convenience, are originally noted even in the manufacture at the enterprise, and for this purpose it is best to use pieces-mittens or sharp scissors.
  • Do not forget that the color of the backlight also plays an important role, since it is able to have a psychological effect. The yellow-green light will soothe and relax, and red, on the contrary, irritate; yellow is considered a neutral shade.

Installation of the profile for LED tape. 3 types.

The LED profile in the backlight performs two main functions:

The LED tape is warming in the process of its work and the more it heats up, the faster the crystals in LEDs degrade. That is, the tape will lose brightness much earlier than its warranty period.

Therefore, for her it is necessary to maintain a certain temperature mode of operation. This is achieved by heat sink from the surface of aluminum profiles.

The groove is specially created on the surface, and the profile after immersion in it is obtained at the same level with this very surface.

Since the main function of the LED profile is heat removal, a very important parameter to which should be paid to the area of ​​its surface.

The higher they are, the better. Therefore, during installation, be sure to maintain free access for air to each side.

For example, when installing a patch profile, at least one surface (lower) is already isolated. Therefore, it is necessary to make special spacers on it.

It can be plastic or metal elements. It is best to use factory fasteners for this.

The main thing is to provide air passage under the substrate.

If you can’t do this, buy products with high sides-15-20mm. Then it will be possible to fasten closely.

There are also profiles that are included with a removable base. In them, at first the base is attached to the surface, and the profile itself is already inserted into it. Between them and the necessary gap is provided.

The rules for creating gaps applies to sides. You cannot mount them, which is called back to another surface.

High sides, in addition to better cooling, have another advantage. Thanks to them, inside you can easily place special connectors to connect the strips of the tape.

With low sides, you will have to remove the upper closing cover from the connector. And insert the connector itself on the side, first stiffing it a little with a file.

stretch, ceiling, tape, installation, plinth

Based on the foregoing, it is best to use the overhead profiles. Other species in any case will be closed from the air from any of the sides.

As soon as the mortise profile is inserted into the groove, it immediately isolated three sides. Only the area of ​​the upper protruding side remains, and this will clearly not be enough.

It is recommended to choose models in which this site will be as wide as possible. Firstly, the best cooling, and secondly, you do not need to cut the groove in furniture with an accuracy of a millimeter. You’ll make a mistake and the profile will just fail there.

In fact, cutting species perform only one function. decorative. For powerful LED ribbons in the absence of voids and gaps, it is better not to use them, the maximum for tapes up to 9.6 W/meter.

The same applies to angular models. When you put them in a corner, then immediately isolate it on both sides.

Therefore, such profiles are not advisable to use precisely as a heat sill when working with bright and powerful LED ribbons SMD 5050, 5630, 5730.

Several varieties of aluminum profiles from KLUS, components to them and dimensions:

To all profiles you can choose special polycarbonate dialogue. Polycarbonate has high mechanical strength and is not subject to destruction from ultraviolet radiation.

The glow angle of 120 degrees LED tape and it without any screens simply illuminates the space in front. At the same time, with low.power diodes, you can visually observe the pronounced points of the glow, and sometimes the dark gaps between them.

How to install LED tape on the ceiling in a plinth

Training

Before fastening Duralight, it is necessary to carry out a number of preparatory measures:

  • Calculate the exact number of materials;
  • Decide what type of lighting will be used, take into account the brightness of the light source, decorative elements;
  • Choose a power supply. In this case, the required voltage, power, humidity in the room is taken into account;
  • If it is supposed to change colors and intensity lighting with LED ceiling tape. It will be necessary to purchase a controller.

Next, the surface is prepared for work at the place of fastening of the tape. First, the inside of the baseboard, the ceiling, or drywall is degraded with solvents (acetone, white spite, alcohol), all defects are removed.

We collect the tools that will be needed in the work:

  • ladder;
  • pliers;
  • soldering iron and solder from lead and tin;
  • hacksaw;
  • roulette;
  • simple pencil or construction marker;
  • electric drill.

Installation of a plinth tape

The tape is attached to the ceiling only once. If you confuse something, make a marking incorrectly or make a mistake when connecting the elements, it will be difficult to fix the flaw. Therefore, at each stage it is required to observe attentiveness.

Initially, a project is drawn up, according to which the ceiling structure will be assembled:

  • If the length of the tape is more than 5 m, the sequential connection cannot be used. Each source of such a length is connected to a separate power supply. Then, upon failing of one section, the rest will work properly;
  • Before installation, it is necessary to check the real power of the diodes, which may differ from the declared manufacturers;
  • For installation, only even base is selected. Otherwise, the device will overheat.

First, a decorative skirting board is fixed under the ceiling. The surface of the wall should be even, dry and clean.

  • liquid nails for light polystyrene cornices;
  • special adhesive compounds;
  • Self.tapping screws if the skirting boards are made of wood.fiber plate or wood;
  • plaster for attaching frizes to concrete overlap.

The laying of the plinth starts from the angle of the room. To get even joints, the masters advise using a special tool in the work. a knock with which it will be possible to cut a filler at an angle of the required value. When the baseboard is installed, the joints between neighboring elements are sealed with sealant or putty.

Duralyite is attached to the surface until the skirting board is installed if:

  • The distance between the ceiling and the frieze is small, does not allow you to securely fix the device;
  • high.side skirting board;
  • The tape will be laid in the groove on the front side of the baseboard.

In other cases, the installation of diodes is carried out after fastening the cornice.

The main rules for the installation and connection of lighting:

  • the tape can be cut only in places indicated by “scissors”;
  • Using the soldering iron, you need to monitor the contacts so that they do not overheat. If you do not want to mess with the soldering iron, purchase special connectors. With their help, individual elements of the tape are connected into a holistic system. Connector connectors are round or flat. Choose parts in accordance with the type of mounted device;
  • If a one.color tape is attached, the duralite is directly connected to the PSU, then to the network. When installing a multi.colored device, the BP is first connected to the controller, and then to the LEDs.

On a note! You can not install BP in space without air access. You can equip for him a place behind the baseboard or build a niche from drywall.

It is more convenient to connect the ribbons on the floor, to check the performance there:

  • Determine the length of the Duralite, make individual parts using connectors;
  • Connect the device to the controller (if the device with a multi.colored glow is used). On the controller there are connectors for connecting red (r), green (G) and blue (b) wires. Black wires are connected to the TT terminal;
  • Connect the controller with the power supply;
  • Check the quality of the chain. If everything is in order, go to the installation of the system for the ceiling.

To fasten the tape on the back of the product, the protective layer is removed, and the adhesive side is applied to the surface of the wall, ceiling or skirting board.

Options for using the tape in the lighting of the ceilings

Installation of LED backlight under the stretch ceiling is possible in several main ways. The choice depends on the original design idea of ​​the owners of the room, as well as the height of the room and the distance to which it can be reduced for the device of the lighting system.

Single.level stretch ceiling with LED backlighting along the perimeter

A single.level stretch ceiling with LED backlighting around the perimeter is the most popular way to use the tape. Visually it seems that the ceiling soars in the air. A soft glow helps to tune in to rest and creates an atmosphere of calm and comfort. The brightness of the backlight can be adjusted. The LED tape is attached behind a special ceiling baseboard slightly below the ceiling level, and the stretch fabric is suitable for both glossy and matte.

Stretch ceiling with LED ribbon

Stretch ceiling with LED ribbon stacked inside, allows you to create a unique light pattern. With one pressing of the switch, you can turn a room into a disco hall, light a starry sky or please children with images of the heroes of your favorite cartoons. For patterned backlight, it is necessary to use a tensioned sheet that transmits light rays. The glossy film in this case will not work, since it is absolutely opaque. It is better to opt for matte canvases.

Two.level backlight

The lighting ceiling illumination with LED ribbon is also possible when creating two.level structures, the perimeter of which is made of GKL. In this method of installation, the tape is hidden in the resulting drywall box. There you can also place a power supply and other necessary equipment. It is not recommended to use glossy tensioned fabric: the tape and all accessories will be reflected in it, as in the mirror.

A translucent stretch ceiling

Another interesting way to install the backlight under the stretch ceiling is the use of a special light transformed stretch fabric. Produces it, for example, the French company Clipso. Such canvases have a smaller thickness compared to fabric or PVC models and pass the light well, which allows LED lighting to play the role of the main lighting in the room. Unfortunately, a ceiling of this type will cost quite expensive.

Try to use in the design of the ceiling LED ribbons of different types that differ in color, the number of LEDs per square meter. This will create several lighting zones in the room and diversify the interior.

Peculiarities

Stretch ceilings personify lightness and airiness, so you should carefully approach the choice of lighting. Using dynamic backlight, you can get a clear supply of light in any room. At the same time, try not to overdo it, since the balance between smooth and “cutting” light should be observed.

The LED tape has the features that you should familiarize yourself with the purchase:

  • Optimal lighting. LEDs shine at an angle up to 1400 degrees. This quality makes it possible to cover a large area;
  • saving. Small light bulbs can replace the usual lamps, consuming a small amount of energy;
  • Long.term operation. The manufacturer guarantees 10 years of work;
  • LED tape quickly pays off. Despite the high cost, this type of lighting is able to recoup itself in 1.5 years due to savings on electricity;
  • Using a dimmer, you can control the brightness of the backlight;
  • Uniform lighting. Silent lamps using one movement can illuminate the room for full brightness.

If you decide to use the option with the LED ribbon under the stretch ceiling, remember that the lighting should be created for comfort. Many users choose LEDs as a decorative component. They will also be useful if you need to set accents on some room objects, visually increase the room or zone space.

A wide selection of colors expands design capabilities.

Which one to choose?

The organization of lighting the stretch canvas can occur using the following options:

  • Using contour scattered backlight. This element forms a continuous strip of light. In it, LEDs can be located on the shelves and shine up. A similar method is considered the simplest, but with its help you can realize many creative ideas;
  • directed backlight, where the lamps are on the slopes that are located along the ceiling. This feature forms “rays” diverging on the main ceiling canvas;
  • Point lighting. Another name is “Star Sky”. Such diode backlighting consists of LEDs, the luminous flux of which looks from the ceiling to the floor. The installation of the “starry sky” has some difficulties, so installation work should be given to specialists;
  • Installation of curly elements. In it, LEDs will be located in special ceiling. Elements should have a small size.

To choose the right LED lighting, consider the following nuances:

  • The number of LEDs. LEDs in tapes are located with a certain density, which affects the cost of electricity and the degree of brightness of light. The ribbons in which 30, 60, 120, 240 elements are present are popular. As a rule, small elements have a more frequent location compared to large ones;
  • Power level. With this parameter, you should decide to correctly choose the power source. Calcurning power consumption is simple: if the consumption level of each LED is 0.04 of the watt, a tape of 60 elements requires 2.4 W for a tape. When using a 10-meter circuit, the formed number must be multiplied by 10. As a result, we will get a 24 watts value;
  • voltage level. Most of the power sources function on direct current, the value of which is 12 volts. There are also more powerful devices on sale, with a power of 24 volts. For such elements, a reduction transformer will be required;
  • Color solution. Many users choose white backlight, but manufacturers offer a variety of options. In modern ribbons there is the possibility of changing the color scheme, which can be changed based on the mood of the user;
  • Lighting control can be carried out using an IR remote or ordinary smartphone. These devices allow you to change the lighting parameters, control the level of brightness and color.

Beautiful examples in the interior

To choose your option to illuminate the ceiling with LED ribbon, you can turn to the examples of a beautiful design from a photo gallery.

  • A classic example of focusing ceiling protruding tape lighting, combined with spotlights.
  • Flexible ribbons favorably emphasize the curly lines of the two.level ceiling, emphasizing the guest space of the living room.
  • The allocation of the complex design of the dining area with a table-standing table looks unusual, while it is not without harmony.
  • Reception of combining LED backlight and spotlights due to different shades allows you to create a bizarre ceiling composition.
  • An unusual version of the built.in tape lighting with the effect of lightning on the ceiling looks spectacular.
  • Accenture of a multi.level ceiling space by lighting of different colors creates a unique effect.
  • Highlighting a small fragment of a stretch ceiling with tape lighting creates the illusion of the realism of the image.

In this video you will find a master class on installing the LED tape, and useful tips that will help to avoid typical mistakes.

Advantages and disadvantages

The advantages of LED backlighting can be said a lot, its advantages.

  • safety;
  • simplicity of installation;
  • durability;
  • the possibility of embodiment of any design solutions;
  • visual attractiveness;
  • economy.

The disadvantages of the system are associated with a short service life of LEDs-5-7 years, because of this it is recommended to choose a more repair-free installation of LEDs below the suspended ceiling, otherwise the repair will require dismantling the entire structure. When installing lighting on the wall, a decrease in the height of the room from 10 cm occurs, which is significantly for standard multi.apartment housing.

Recommendations and tips

When choosing a installation method, focus on the height of the room, instead of a multi.tiered structure, it is better to mount a soaring ceiling that visually increases the height.

The sky with clouds looks great in small apartments of the stretch ceiling, the canvas with such a seal will also increase the visible height of the room.

When determining the number of crystals per meter of tape, focus on the type of lighting:

The color temperature also takes into account the purpose of the room: the cold glow is suitable for the bathroom or kitchen, warm light. for the living room, bedroom, hallway.