How to cut an angle on a ceiling plinth

How to cut a ceiling plinth without a joiner? For work a well sharpened pencil, a small piece of baseboard, a box cutter (for polystyrene or polyurethane) or a metal saw (for other materials), a ruler are needed.

You need to put the baseboard to the corner and draw a fishing line with a pencil along the outer edge, then put it to the other side of the corner and also mark. As a result, on the ceiling will get a cross, the center of which will mark the place where the planks of the ceiling plinth should converge.

Place a section of the skirting board where you will glue it. With the end in the wall, transfer the desired mark on it. It is possible to cut the corners of ceiling plinths without a joiner.

How to cut?

To properly cut the ceiling plinth in the corners with the use of a plank, you need to meet several requirements, namely, to prepare a carpentry machine with certain parameters and the plank. It is necessary to remember that plinths, moldings are made of different materials. woodworking products, modern polymers. It makes sense to list the characteristics of each material.

• Wooden strips are very strong and heavy. Therefore, you should prepare a sharp hacksaw.
• Foam moldings are quite fragile. During processing, they crumble, making the process difficult. It is recommended to trim the corner with a sharp knife.
• Products on the ceiling of PVC the same is not characterized by high strength properties. It is better to cut such strips with a hacksaw without pressing too hard.
• Tacks of extruded polystyrene foam do not crumble, trimming corners of this material takes less time. A construction knife or a hacksaw can be used.
• Cut corners from polyurethane moldings is also not a serious difficulty. This material is well cut with a sharp knife and does not form crumbs.

To properly cut the outer or inner corner of the baseboards, you must first perform a marking. attach the product to the ceiling and mark with a pencil a thin scythe line. In order to cut the fillets at a certain angle with a wire cutter, you must follow detailed instructions, which can be obtained from an experienced carpenter. Beginners first of all it is recommended to practice on an unnecessary piece of wooden workpiece, so as not to spoil the decorative element. Try to make both inside and outside corners, to achieve a good cut in order to avoid mistakes in the future.

Try to make the inside corner first, then the outside.

• Lean the skirting board against the joint on the ceiling, and measure the required length.
• Place the skirting board in the carpentry machine, facing outward.
• Press the strip against the wall.
• Hold the molding with your left hand and take the hacksaw with the other hand.
• Choose a 45 degree position.
• Decide on a comfortable cutting position.
• Start cutting without exerting too much pressure on the cutting tool.
• Immediately saw a mating fillet.

After finishing the work, the obtained planes should be docked on the floor and the accuracy of the sawing should be checked. Carefully work out any irregularities with sandpaper. Now you need to make the outer corners. Why is it so important to make the inner corner first, and not the other way around?? Justified step will not allow you to make a mistake with the measurements. In the opposite case a force majeure situation is possible, when the tack may be insufficient in length. Therefore, the second stage. the formation of external corners. How to make beveled edges with a carpentry machine?

• Take a skirting board, put it to the ceiling and mark dimensions with a pencil.
• Place the decorative material in the jigsaw and press it against the wall with your left hand.
• Take the hacksaw with your right hand and choose a 45-degree slash position.
• Cut along the marked line.
• When cutting, do not apply too much pressure on the hacksaw, so as not to spoil the decor.

Also saw down the bevels in the mating strips.

How to properly make the corner of the ceiling plinth

Installation of skirting boards (or ceiling plinths) can be a real challenge, even for those who already have experience in repair and finishing works, because the main task is to connect the edges of the ceiling plinth in the corners of the room so that there were no gaps and slots. Besides, quite a few apartments built in Soviet times are distinguished by perfectly flat walls and corners, which complicates the task at times. The question arises: how to properly file the baseboard and make an even, neat corner at home? Let’s look at several ways.

Ceiling plinth or batten serves as a final element in the design of the interior of the room.

It is worth noting that ceiling plinth, or as it is also called, ceiling mouldings are made of different materials, so not all options, will be equally effective for different types of plinths.

The main goal is to properly cut the left and right ties. Connection must be tight, excluding the formation of gaps. Using foam ceiling baguette, the deviation is easy to correct due to the softness of the material. If you’re dealing with plastic or wood, it’s worth the effort. In any case, you must start from a corner, so you will have the opportunity to correct any inaccuracies if necessary.

How to cut a corner without a joiner

It is possible to cut a corner and glue a skirting board without a joiner. Let’s tell you how not to spoil the look of the baguette.

• On any solid base draw a fishing line.
• From the mower line make an indent of 10 cm and run another line.
• At right angles draw a line through the parallels.
• From the line on each mowing line we make a 5 cm mark and connect the opposite points with lines.
• The mowing line with the parallels will eventually form an angle of 45 degrees.

Thus we get a homemade plank, and now we need to determine the slope and make the cut of the skirting board.

• Boards we attach to the ceiling and determine the direction of the cut for accurate and correct installation.
• For the inside corner, the top edge should be shorter than the bottom.
• For the outer corner the top edge must be longer than the bottom.
• Cutting the baguettes should be mirrored.
• For the skirting board, which will be located on the right, a cut must be made from the left side. For the trim, which will be on the left, the cut is on the right side.
• We lay the skirting boards on a homemade jig along parallel lines and, taking into account the direction of the angle, make a cut according to the marks.

To make the cut without roughness and splinters, you need to carefully advance the knife in one direction.

Cut the inner and outer corners of the skirting boards

Evenly trim floor moldings is no more difficult than ceiling moldings. Only we choose the tool for trimming according to a material which we will saw. The actual sawing process is also similar, but for the handheld circular saw, it has a slightly different method of marking.

To cut a wooden floor molding by means of a wire cutter

It is necessary to measure the distance from the edge of the baseboard already glued on the wall to the top of the wall corner. Now take a new piece of molding and postpone on its lower edge the length equal to this distance. Put a point with a pencil or put a piece of masking tape on it. Repeat this procedure for both the outer and inner corners. In the jigsaw, we place pieces of baseboard from left to right for the left side of the corner, and from right to left. for the right. At the same time, press them as in the figure to the side of the trimmer closest to you.

How to cut the corner of the ceiling plinth laying the workpiece in the jig:

• For the outer left one, match the mark on the baseboard to the leftmost slot. For the outer right. with the extreme right.
• For the inner left match the mark on the baseboard with the rightmost slot. For the inside right corner. from the leftmost point.

To clarify: the slit is the one on the side that is closest to you.

Cutting the skirting board at an angle: the red line marks the place of the cut

Floor plinth: inner and outer corners “by hand”

Moldings for the floor, as a rule, rather wide and thick, and therefore here finding only two points, as for the ceiling baguettes, can not do. To trim the inside corner at first we put a point on top of it at a height equal to the width of the baseboard. in the picture it is a point in green. From there, to the left and right, we mark off a distance equal to the thickness of the baseboard. points 1 and 2.

We enclose the left piece to the wall, and from point 1 draw a fishing line along it, perpendicular to the wall and on the edge we put a point. Repeat with the right side, but draw from point 2. In the picture the point is marked with the number three. From there across the skirting board, run a fishing line to the opposite edge. Now connect the green point with points 3 and 4. we get a fishing line and an angle at which it will be possible to saw the molding.

How to cut the skirting: in the corners, the necessary marks are made

Important: trimming outer corners is easier to do than inside corners. On the left and right sections exhibit points: A. mark the top of the corner of the wall; C. point of intersection of the lines, which is obtained by drawing the left and right sections of the skirting across the floor; B. from point C across the molding is drawn a line to the opposite edge.

Connecting these points with each other with a line gives us the line that will be used to make the cut.

What is it made of

The first plinths for ceilings were made of gypsum. Its various elements are cast in specialized molds. Gypsum baseboards are still being poured. However, due to the high cost of the product, its heavy weight and brittleness (it is not easy to install), it is almost never used in apartments and detached houses. In connection with it plaster moldings are cast, as a rule, insignificant parties for repair-restoration works or the elite cottages.

In ordinary living quarters practice other materials:

• Styrofoam. It is a very fragile material, and should be handled with care. Its advantage. availability to most consumers.
• Polyvinyl chloride (PVC). The cost of products made of it is not high, but with it, as well as with foam, you need to work carefully.
• Extruded (extrusion) polystyrene foam. Baguettes made of such material are strong and reliable, their price is higher than the previously described products. They are not easy to break, they do not crumble when cut.
• Wood. Wood makes the strongest type of such products.
• Polyurethane. It is used to make strong ceiling ties. They have a big disadvantage. polyurethane products hardly react to temperature fluctuations and are characterized by susceptibility to heat or cold. These features should be taken into account before trimming ceiling tie in the corners.
• Rubber. Elastic and soft material is practiced mainly as a supplement to the suspended ceiling. it covers the gap between the canvas and the wall.

How to make a corner on the ceiling plinth without a stool?

Every person in his life has faced with the repair in one way or another, and we all saw the ceiling plinth or baguette. In construction stores a huge number of different options ceiling plinths from thin width of 1 cm to a huge “carved” in the Victorian style. They are all designed to make a clear distinction between the ceiling and the walls, to complete the interior, to hide defects and joints. Any ceiling molding is in the form of slats, and to joint in the corners it must be properly trimmed. about this today and will be discussed in this article.

Preparatory work

First of all, it is necessary to perform a number of preparatory works:

• buy the necessary materials and prepare the tool;
• Remove extraneous objects and furniture, providing free access to the walls;
• Clean the surface of the walls and ceiling of dust, and in the absence of wallpaper, tiles or panels to cover with primer in 2.

If you were planning to glue a colored skirting board, it is better to paint it at the preparatory stage.

How To Cut & Install Crown Moulding

Ceiling plinth. batten

To do this correctly, it is important to strictly follow the existing recommendations and rules of finishing work. You will be pleased with the result.

In the attachment of the fillet (so called this element) there are no difficulties: in fact, all varieties of products are attached to a reliable adhesive.

In order to hang a ceiling plinth, even inexperienced repairmen have no difficulty. Worries them quite another thing: how to properly cut the ceiling plinth? In fact, almost every room, no matter how intricately shaped, is equipped with corners.

And here in these internal corners, the individual elements of the skirting board must be beautifully and evenly docked. And in rooms especially complex configuration will have to fudge over the outer corners. Let’s try to figure out how to be in each of these situations, and how to cut the right piece with the tools available.

Baseboard materials and cutting methods

First of all, let’s try to determine what the baseboard can be made of, and with what particular material is better to cut.

On sale today you can find products made of foam (PVC), wood, polystyrene foam and polyurethane.

Perhaps some of the cheapest are baseboards made of foam plastic, which is a fragile, soft and brittle material.

Even the fingers of the hand can leave dents on them, they easily form creases and defects. It is quite difficult to cut a nice and even corner of the PVC baseboard.

An inexperienced craftsman can throw away a large amount of purchased material for this very reason. Also, this polymer has high electrostatic properties, which explains its ability to collect dust.

It is more convenient to cut such a skirting board with a hacksaw or a sharp construction knife.

Products made of expanded polystyrene are also inexpensive, although this material is more durable analog of traditional foam.

They are also machined with a sharp tool.

Extruded polystyrene foam

Skirting boards made of extruded polystyrene foam cost a little more, they are somewhat denser and it is more difficult to cut them. But they are much less likely to crumble and break.

Therefore, it is more convenient and easier to cut them. It is convenient to use a hacksaw or sharp knife for this purpose.

Polyurethane skirting boards for ceilings are currently probably one of the most expensive.

But they are worth their price: moisture-resistant, quite strong and tight, quite elastic.

Baseboards above the stove can get warped or even crack a little.

They are perfectly cut with a special knife, and do not form crumbs. But they are sensitive to temperature fluctuations.

Wooden plinths for the ceiling are quite heavy and dense products, hard and durable.

They can be sharpened very well with a special fine-toothed hacksaw. You can also use a reliable metal blade. So how do you cut a ceiling plinth correctly??

Prefabricated angles

Note that every master has the opportunity not to pore over the precise cutting and fitting corners.

In a construction store you can buy a factory-made corner piece, in which the prepared edges of the baseboard can be easily inserted.

It is enough to measure the necessary length of the blank, and cut it at right angles.

All defects and flaws will be hidden by this special element. But such a convenient way to use is not always possible, because the standard dimensions of such factory corners may differ markedly from the size of the baseboard itself.

Such corners will stand out for their disproportionality, and it will not look very neat. But if the design of the room and the size of blanks allow you to use this method, then you should not neglect it.

Those who have to use one of the methods of trimming ceiling plinths, the following tips will be useful.