How to cut glass mosaic on a grid

Features of laying mosaic on a grid

Laying mosaic tiles on a mesh is much easier than installing a similar option on a paper backing.

When laying the mosaic on the grid, you will see a picture that should be folded into a panel. And when stacked on paper, the drawing will be hidden until the paper is cleared

• first you need to unpack the mosaic and lay it on the floor in the desired order. This will facilitate the process of laying on a vertical surface;
• then you need to make the markings on the wall. You need to start laying from the largest surface from bottom to top;
• preparation of tools and mixing of the composition is necessary. The glue or mortar mixture is mixed twice, then applied to the wall surface in portions sufficient to adhere one sheet. Thanks to a properly mixed solution, the mosaic is easier to install. Depending on the type of glue, it dries for about 15 minutes;
• glue is applied with a notched trowel and a mosaic sheet is applied, focusing on the marking of the mowing line.
• after applying the glue, the sheet is pressed to the surface and smoothed with a rubberized float. If necessary, correct its position, checking the horizontal position using a building level;
• the seams between the tiles are filled with glue when pressed, its excess is removed with a damp sponge;
• the mosaic dries up in about two to three days.

Ceramic mosaic and porcelain stoneware

The ceramic mosaic is a smaller version of the usual tiles. It comes in different textures, colors, glazed or has a matte surface. Ceramic tiles on a grid are unpretentious in maintenance and do not require special conditions during installation.

The porcelain stoneware mosaic tile is highly durable and durable, it can be used for cladding the floor in the bathroom, toilet, and it is also used for pool bowls.

Which glue is better to use

The glue is chosen depending on the type of mosaic, it can be:

• standard. used for laying opaque types of mosaics. It contains Portland cement, sand, and special additives. Can be used for walls made of concrete, stone, brick, is the most affordable and versatile glue;
• white. its composition is almost the same as the previous version, only white pigment is included here. It is used for transparent tiles;
• polymer glue is used for curved, broken surfaces, it provides better adhesion;
• glue with the addition of construction PVA, it is suitable for laying mosaics on a wooden surface.

The consumption of special adhesives is approximately 2 kg per 1 sq. m. To apply glue, a set of tools is required: a notched trowel, rubberized float, level. For opaque mosaics, tile adhesive can be used.

Materials for creating decorative surfaces

The mosaic can be used not only for wet rooms, but also for the living room. A fragment of a wall, a fireplace, niches can be faced here. Mosaics with decorative inserts are used. The use of a mesh under the tiles will greatly simplify the installation process.

Preparation of the base

The base for the tiles must be leveled. Mosaic is not suitable for facing exposed surfaces. Any inaccuracy in the wall will be visible after the adhesive has dried. Sequence of work to prepare the foundation:

• clean walls from coating and construction dust;
• cavities must be plastered, cracks that need to be filled with plaster must first be expanded and cleaned;
• check the horizontality and verticality of the surface using a building level;
• to level the base, an elastic compound must be used, it will also protect against the formation of mold and mildew on the surface during operation.

Working with modules made of natural stone

There are two types of modules: hand-pricked and factory-shaped. Depending on the complexity of the work, the desired option is chosen. For manual production, special nippers are used. Industrial modules are of different types, the most durable are 10 mm thick. Elements with a thickness of 6 mm are also produced. They can be made of natural stone: marble, travertine. Natural stone colors create interesting and pleasant combinations.

How to glue a mosaic on a grid, expert advice

Mosaic has been used since ancient times, when the installation process took more than one year. Now manufacturers produce mosaics on a grid, and its installation takes much less time. Patterns made of small elements: glass, ceramics, mirrors, metal, natural stone are used to decorate walls and ceilings in bathrooms and bathrooms. A mosaic on a grid can serve as the main type of cladding, or be a fragment, for example, a rectangular panel or used for cladding a work surface in a kitchen.

How to grout joints

After the glue has dried, it is necessary to perform the following operation. rubbing. Grout for a mosaic on a grid is selected not only by color, but also by the purpose of the room. For a bathroom, toilet, kitchen, deep penetration compounds with epoxy resin are suitable. This grout is durable and withstands mechanical and chemical influences. You can rub the joints on the inner and outer corners with this compound. The only drawback of epoxy grout is that it is more difficult to work with and requires experience to apply. Epoxy grout comes in a variety of colors, and there are glitter options as well. They look very decorative and match solid color mosaics. After the adhesive dries, the grout is applied with a rubberized spatula. The larger its working surface, the more convenient it is for them to work. Excess grout is removed with a damp and well wrung out sponge. Then the surface must be wiped with a dry cloth. If the grout dries on the surface of the mosaic, it will be very difficult to remove it.

It is important to apply the grout in small areas in order to have time to remove the residues before it dries.

How to properly glue a mosaic on a grid, secrets for craftsmen

Any interior of the house, be it a kitchen, be it a bathroom, bedroom, corridor, pool, can be decorated with mosaics. Quite often, the mosaic is supplied already glued to the grid, which allows you to work quickly. But how to properly glue the mosaic on the grid so that all the rows are even and beautiful, we will try to explain on the pages of our website.

How to prepare the surface for laying the mosaic on the mesh

The surface on which it is planned to lay the mosaic on the mesh in the future can be absolutely any shape, the mesh can be laid on any curved surface, but you must follow some general rules that apply to the wall or floor before applying glue.

Here’s what to do with the surface before laying:

• Make sure the surface is level. It depends on this parameter how ideally the laying will be then done. Differences on the surface cannot always be stretched due to the thickness of the glue; it is best to plaster and rub the surface. It should be borne in mind that if the deviations and distortions of the surface are large and cannot be eliminated by plaster, then it is best to break the old base and make a new one using drywall.
• Make sure the surface is clean. All dust and dirt must be removed. If sanding was performed, then the accumulated dust must be removed with a vacuum cleaner and clean rags.
• Don’t forget to prime. Always prime the surface before laying any similar material, this will increase adhesion and adhere to the surface. Deep penetration primers are most effective at this stage of preparation.

After these conditions are met, you can start applying glue to the surface and then lay it. Sticking a mosaic on a grid is a rather difficult process and it is better to entrust these works to professionals.

How to prepare mesh mosaic adhesive

Mosaic glue differs from the tiled version, since it is necessary to use a two-component composition. It is this glue that can reliably glue the mosaic on the mesh to the base. Find the right adhesive before reading about how to glue a mosaic on a mesh.

These are the glue options that can be used in the work of the master stacker:

• Standard glue, cement-based, as for tiles. Such a mixture is not suitable for use in the pool, since only a highly qualified specialist will be able to select all the necessary ingredients for this type of glue. This option can be used for opaque ceramic and natural stone mosaics for installation on the wall in the hallway or for the kitchen apron. The method of gluing the mosaic on the ceramic mesh corresponds to how it will be described below.
• A solution based on individual ingredients that mix independently. For its manufacture, cement, fine sand and water are used. Similarly, this mixture is suitable for ceramic and natural stone mosaics, but not suitable for glass mosaics.
• Adhesive with latex additive. Usually it is white, which visually immediately differs from its purely cement counterparts. It is used for laying mosaics on a grid in the pool and wet areas, for example, in showers and toilets. Two-component glue for mosaic on a grid is the most effective option, but also the most expensive.
• Glue with polymers, it consists of polymer components, after mixing and laying, such glue becomes like stone, it hardens very strongly and can firmly hold the mosaic to the base. Glass mesh mosaic can also be glued with resin adhesive.
• Other options. Manufacturers of adhesives do not sit idly by and are constantly improving adhesives. Therefore, you can also find glue with an inscription. for glass mosaics or for natural stone mosaics. It is also worth paying attention to the recommendations made by mosaic manufacturers, since it is clear that the manufacturer is interested in his material being presented in the most presentable way.

Features of the mosaic fixed to the grid

Another of the original solutions is a mosaic. pebbles, on the mesh it is assembled in large fragments with gaps between elements of different sizes.

There are different types of nets, but the best ones are polyurethane-based nets. It adheres very well to mosaics and can be installed in a damp area. The cheapest mesh option is gauze. This type is the most common among domestic mosaic workshops. This option is suitable for gluing on the wall, but for floor use it is better to use it for areas with low traffic. In places with heavy traffic, the mosaic on the fabric mesh can loosen and fall off very quickly.

The mesh on the mosaic is fixed only on the back side of the material. This is a dramatic difference from the paper-formed mosaic mesh.

What types of mosaics are being made today:

• Ceramic mosaic. It can be produced as separate tesserae, or the material is sawn from tiles of a standard format. Manufacturers use only the highest quality material for cutting, which is why this type of mosaic is quite expensive. Ceramic mosaic on a grid can be laid in any area of ​​the house on a simple cement mortar, provided that the ceramics itself is intended for floor use. I would also like to note that ceramic tiles, mosaics on a ceramic mesh are well combined and designers often use this installation option when creating an interior.
• Glass mosaic or glass mosaic. Such material is baked in specialized factories from a special fir, consisting of ground glass and dye, after passing through firing in a chamber or conveyor or continuous oven, the material acquires high strength and is absolutely not afraid of water. There are options with a translucent structure, which allows you to paint over the back side with different paints and get a very unusual design of the material. Glass mosaic on mesh is mainly used for wet areas, especially in swimming pools.
• Natural stone mosaic. This is perhaps the most impressive mosaic, as in addition to the beauty of the mosaic itself, natural aesthetics are added to the material. Taken together, this is all the charm of this option of finishing material for framing the bathroom. Most often, such a mosaic is made from granite or marble.

Mirror mosaic on a grid is a decorative design option and does not belong to finishing work. Decorating is considered in other interior design work.

Rules for laying mosaics on a grid

The master must definitely know how to properly lay the mosaic on the grid with his own hands. This experience should be acquired not in theory, but in practice. Well-known manufacturers even issue special certificates to craftsmen who have been trained in this craft and have proven their skills on real projects. Unfortunately, in our country such masters can be counted on one hand; self-taught masters often do this. If your interior is dear to you, try to find and hire a real mosaic expert.

At the same time, you, as an observer, should be aware of the main stages of installation:

• Layout. The mosaic on the grid is laid out on the surface in order to have a clear picture in color matching. If the master skips this stage, then in the middle of the work, a surprise may await him, there is a mesh of a different format or color.
• Numbering. After the material is laid out, it is best to number it, so it will be easiest to correctly lay the mosaic on the mesh on the surface.
• Assembly. After laying out, the material must be folded back into the boxes in the reverse order.
• Markup. Mark the surface, roughly as when laying tiles, using a lacing or laser ruler. This is the last step before styling. It remains to disassemble the stage of how to glue the mosaic on the mesh to the base. The size of the mosaic on the grid is usually 32.7 x 32.7 cm, so you can make a preliminary design project for laying the mosaic.
• Styling. After that, you can start laying the mosaic on the mesh. The mosaic is laid on the wall from the bottom up. First, glue is applied, a spatula with a large notch is leveled on the surface, and then the mosaic is glued onto the mesh. The piece to be glued must be gently leaned against the glue and fixed, then you need to tap the surface evenly with a special flat spatula so that the mesh is finally and evenly fixed. Then you will have to repeat this with all the other meshes to be laid. Even special styling crosses can be used between the seams so that the width of the gaps between the individual meshes is the same. Be sure to check the immersion depth of the mosaic in the solution, the mesh should go completely into the solution, while the mosaic should rise above the glue. After all the grids are glued to the surface, you need to leave the time recommended by the glue manufacturer for complete drying. It is impossible to walk on the laid mosaic on the mesh all the time the glue is setting, this can be done only after the glue has completely dried and the mosaic is finally fixed.

The stone mosaic on the grid has a large thickness, so the consumption of glue will be greater than the consumption when laying glass mosaics.

Which mesh meets the standards

Of course, you should not lose sight of this moment. In addition to the base, it must be securely glued to the mesh and mosaic.

This can be verified quite simply. Take the net in your hand and move it easily. The mosaic should not fall off the grid. Even in the sagging mode, the tesserae should remain on the grid and should not fall off.

If the mosaic falls off the grid, then this means that the adhesive composition has dried and become unusable, or the material itself has been exposed to an effect that has torn it off the grid, for example, in case of improper storage.

If the tesserae fall off the grid, then the material should be replaced from the supplier, or asked to re-glue and bring it into line. If you use such material, it is more likely that the masters will have difficulties in laying and your interior may begin to ripple. In manual mode, laying the material exactly is quite problematic and not many mosaicists can do it. Even an art panel needs to be able to properly prepare for transportation and handover for installation. You can see how to put the mosaic on the net in the package in the photo. Two parts of the panel are laid face-to-face through the gasket and then rigidly fixed in the package. A lot of studios do it like a blooper, although it is very important for the entire installation process.

Small mosaic on the grid is produced quite rarely, this is due to the fact that its attachment to the grid is too difficult.

Please note that nowadays marble mosaic on a grid is quite often forged and instead of natural stone, porcelain stoneware with a marbled surface is used, this material is cheaper than real marble. To protect yourself, ask the seller for a certificate for the material and shop in specialized stores.

How to Cut Metal and Glass Mosaic Tile

Finishing work when laying

As soon as the mosaic on the mesh sticks to the base, you need to clean its surface from the remnants of the adhesive solution and start grouting.

Jointing mixtures can be divided roughly like adhesive mixtures, depending on the base:

• Cement;
• Latex;
• Epoxy (a waterproof hard layer is created);
• Mixed.

Marble mosaic on a grid requires special care when grouting. The marble is porous and the grout can penetrate the material or discolor the edge.

Mosaic pliers

In order to correctly cut with pliers, you should take them in the cutting hand, while with the other hand (index, middle and thumb), hold the mosaic firmly and motionlessly. Next, you need to place the mosaic between the two surfaces of the nippers. Now, having covered the tile with the blades, about half, make a break. The direction of this break is set by turning the pliers in one direction or another. To make the applied effort stronger, hold the wire cutters at the ends of the handles. First, it is advisable to practice on a rough mosaic, and only then move on to the main samples.

How to cut mosaic on mesh without chips

In this article we will tell you about the methods of cutting (splitting) mosaics.

How to cut a mosaic

Novice mosaic masters often have a question. how to cut (chop) a mosaic, with what tool. Even experienced craftsmen cannot always answer this question. Even now, there are still builders who use a conventional “angle grinder” as a cutting tool. But with such a tool, apart from the mosaic, you can cut something else, something “necessary”. Sometimes ordinary glass cutters are used to reduce the cost, but you can’t do much with such a tool, and it’s not convenient either.

Professionals who value their time and the quality of the work performed should have a high-quality professional tile cutter that can cut mosaics as well. But this option will result in a pretty penny, and it will be problematic to perform curly elements on them.

Like this tile cutter with a mosaic mat, you can cut quickly and a lot, but this type of cutting is not suitable for artistic splitting.

Therefore, for those who do not know how to cut a mosaic, we hasten to share a list of tools and methods designed specifically for this lesson. Almost any master can learn this, whether he is a beginner or a skilled worker with experience.

Roller cutters (tongs) for mosaic

Roller cutters (pliers) for mosaic is the most convenient and functional cutting tool. This tool can combine the functionality of a glass cutter and, in fact, the mosaic cutters themselves. Outwardly, this tool is somewhat reminiscent of a modern can opener. The tip of the pliers consists of two strong, sharply-sharpened discs. A piece of mosaic is inserted between these discs, and by squeezing the handles, under the influence of force, the discs cut the mosaic in half. If you practice well with this tool, you can make not only straight cuts, but also curly cuts, giving the mosaic a different shape. When the cutting rollers become blunt, they just need to be turned a little, having previously loosened the screws with which they are pressed against the pliers body. When the desired position is selected, retighten these screws.

It is worth noting that when working with any of the above tools, you should follow safety measures. Because, for example, using roller cutters, when cutting, a fragment of the mosaic can please the performer in the eyes. Therefore, when working, wear protective glasses, and gloves can be worn on your hands so that the fragments do not fall under the skin. Thus, you will protect yourself, and you will be able to act confidently and accurately.

There is a whole line of specialized ones specifically for processing. Such a tool will be especially useful when making mosaic panels or decors. Since in this process, the mosaic chips are constantly being cut and crushed into smaller pieces, which must be skillfully folded together.

Mosaic cutting is a real challenge, especially for those new to the craft. Glass or stone can behave completely unpredictably, break into pieces that are not planned in shape and size. Special mosaic cutters can help in the correct processing of the mosaic.

There are several types of them. Some are for cutting mosaic chips,

others for splitting (preliminarily draw on the chip with a glass cutter,

and then they just break with the help of specialized forceps)

One of the most popular and essential tools is the roller cutter. They are also different in design, but they have the same principle. One of the most convenient are the cutting pliers with the mosaic fragments catcher.

A very handy invention. During the cutting of the mosaic, fragments like “bullets” can bounce in different directions from the cutting site. Such a bag, located on one side, prevents them from scattering in different directions. On the other hand, the piece will simply end up in your hand. Also, a traditional set is almost always used: this is a chisel knife and a hammer. This kit serves for more detailed processing. A chisel knife is driven into a block or paneled in order to use its cutting edge as an auxiliary surface (see figure), and give the desired shape with a hammer.

Ceramic tile cutting tool

can be cut with an ordinary roller. We mark it with a soft pencil or marker, then put the tile on a flat hard surface and, pressing evenly on the glass cutter, roll it from the far edge of the tile towards ourselves so that a visible strip remains on the enamel.

Only one incision is made. To break a tile along the cut line of the mowing line, you need to place a match or a small nail under it and lightly press on both sides of the mowing line.

good for when the volume of work is small and you do not want to spend money on tile cutters. However, it is difficult to perform a large amount of work with a glass cutter. In fact, if you need to cut at least a dozen tiles, then it would be nice to “splurge” on a manual tile cutter.

The difference between a tile cutter and a glass cutter is that the cutter wheel is larger in size (1.5 cm in diameter), which allows you to cut to a greater depth. Itself is similar to tongs, as it is equipped with a device that allows you to break the tiles after making an incision.

And with a glass cutter and a manual tile cutter, it is good to cut n. Of course, you can try to cut tiles intended for laying on the floor with them, and it is quite possible that you will succeed, but for floor tiles (and even more so, if it is) it is better to purchase a stationary tile cutter. It allows you to cut tiles with less loss and more precision. Hence the intermediate conclusion: if there is a need to cut floor tiles, it is better to immediately purchase a stationary tile cutter.

The cutting technology is somewhat different from cutting with a manual tile cutter: the tile is marked, installed on the base, tightly pressed against the stop ruler (the tile cutter itself would also not be bad to rest or screw on. there are holes for fasteners in it), cutting is done from oneself in one motion with a slight pressure on the tile; the tile at the end of the cut is broken by light pressure on the lever using the angle located on the lever. Little tip: craftsmen apply a few drops of machine oil to the cutting wheel. and cut is easier and the cut is cleaner.

with a diamond blade makes perfectly straight cuts with smooth and slightly rounded edges, in contrast to the sharp edges obtained with simple tile cutters. Hence, the best quality of the cut tiles, the ability to use to obtain curly cutouts, the ability to cut pieces less than 5 mm, you can cut tiles and porcelain stoneware of any hardness.

Another obvious advantage of electric tile cutters is the cleanliness of work. dust and tile particles settle in the water tank and do not pollute your environment. Cutting tiles with an electric tile cutter does not present great difficulties, however, it requires compliance with safety measures. standard protective equipment is required: gloves, glasses.

Such a tile cutter is more useful for professionals. it costs quite a lot, takes up a lot of space. So, if you are not going to make money with it, you shouldn’t take it.

Along with tile cutters, tiles can be cut with an angle grinder.

can also be used for both straight cuts and curved cuts. The disc is used with diamond plating. An angle grinder cuts tiles as well as a tile cutter, but since it is a hand tool it cuts less accurately and leaves jagged edges. Big minus. a lot of dust.

The angle grinder is a very dangerous tool and must be handled with extreme caution. When using this tool, you must have protective goggles, headphones, a dust mask and be very careful.

An angle grinder is the best option for cutting tiles at home. In addition, it is useful for other types of work.

To drill a hole in a tile, special drills or crowns of different diameters are used.

Mosaic making. Roller cutters.

All sorts of tales are often told about how to cut a mosaic. Human fantasy is limitless. nippers, tile cutters, etc.

It’s simple. cut with an angle grinder.

It is better, of course, to do this with the help of “DREMEL”. But this is another tool in an infinite cost chain.

The impeller blade must not “hit”. This happens in Bulgarians who have worked for more than 2-3 years. You can cut with any circle designed for cutting ceramic tiles.

The success of the cut depends on the type of mosaic, and on what material the mosaic elements are fixed. It is better, if possible, to cut the mosaic on the grid. Even when broken, the pieces remain anchored to the grid of the sheet.

There is such a type of mosaic (or rather the back side) that it is difficult to cut. Some elements burst in half when cutting, due to the relief of the back side.

A glass mosaic sometimes comes across, but the glass is somehow strange, Chinese. Cuts without problems like plastic.

Cutting mosaics with large mosaic elements, especially in the middle, is excellent. When the line of the cut is moved to the edge, the narrow part often splits.

The basic rule when cutting is gradual. First you need to mark the cutting line with the cutting wheel (during the first pass). Then evenly and gradually deepen into the glass surface along the entire length of the cut.

To make a smooth cut, you must lay a guide along the intended mowing line. These can be long lengths of ceramic tiles. After several cuts, the guide must be changed. the edge of the tile is grinded with a cutting wheel, and the evenness of the cut is disturbed.

Working with a glass cutter

Since not all people succeed in cutting glass mosaic from glass, it is worth dwelling on this issue in more detail.

It is important! Old glass is much more difficult to cut along the cut line without breaking it, as it becomes brittle over time.

How to cut glass so that there is as little waste as possible? An old, dull glass cutter can be thrown away immediately, since it will not be of any use. You only need a high-quality tool that can be used to cut glass mosaics. As a rule, when performing work with a good glass cutter, there are no problems with cutting chips.

Rules for working with an oil glass cutter. video

The conceived design can be very diverse, so even at the planning stage, you need to decide on the size and shape of homemade chips. The simplest and most popular square mosaic.

As for its size, here you need to take into account not only how the glass mosaic will look in the interior of the room, but also whether it will be a monochromatic coating or it is planned to create a certain pattern, because a certain pattern will be clearer than a smaller tile is used.

Depending on the selected size, a mowing line is cut through an equal distance on the glass with a glass cutter, as shown in the video.

Master’s tips. how to properly cut glass with a glass cutter, video tips

It remains to cut the strips to make chips of the same size.

Types of glass mosaics

The very process of laying small fragments of a mosaic is very tedious, and now there are not so many specialists of this profile. Nowadays, mosaic tiles are very popular, because their installation is performed many times faster, but it will not work to create an individual pattern from it.

You can purchase a ready-made mosaic (chips) or cut it out of glass with your own hands, and lay out the intended pattern from it. Let’s consider these points in more detail.

Glass mosaic in the interior photo

Many centuries ago, people learned to decorate their homes with mosaics, creating real masterpieces. For example, during the excavations of one of the Roman villas, a mosaic picture was found laid out by a talented master in the 3rd century AD, and it has been perfectly preserved to this day, which indicates the durability of this facing material.

Nowadays, glass mosaic is very popular. an affordable, durable and reliable material with a wide variety of colors and shades.

What glue to use

In the building materials market, you can choose the right glass mosaic adhesive that will meet your requirements. Since the glass mosaic is transparent, the glue for it is selected white.

A suitable shade of glue can be used to glue the colored chips. It is better not to use a gray compound for gluing transparent or translucent material, as it will change the perception of the coating and can even completely change the perception.

Transparent silicone is used when creating stained-glass windows.

Cutting Glass Mosaic Tile WITH NIPPERS (So Easy!)

There are also other criteria worth paying attention to:

• Adhesion. Purchased mosaic glue should hold the glass well.
• Resistance to temperature extremes. If the mosaic will be used outdoors or in a room in which the temperature changes rapidly (for example, a bathhouse), then you need to choose a suitable glue.
• Moisture resistance. There is a lot of humidity in the bath, bathroom or sauna, so simple tile adhesive cannot be used in such rooms.

Broken glass

The process of making a tile from a piece of glass is not difficult, but it is an unsafe activity, therefore, precautions must be taken, as small and sharp fragments can fly apart on impact.

A piece of glass must be wrapped in a thick cloth, put on the floor or table, and with a hammer blow in the center, break it. In this way, ray-shaped fragments are obtained, from which you need to choose the suitable ones, or adjust to size with nippers.

Broken glass for mosaics is very sharp, so it is necessary to work with details with rough construction gloves. When adjusting the tiles to size with wire cutters or a pry tool, take care of protecting your eyes from flying fragments of broken glass.

Laying glass mosaic

Many people paid attention to how just one dropped out element from the mosaic cover spoils the whole view. To prevent this from happening in your case, consider how the glass mosaic is laid.

We talked in detail about the process of installing mosaic tiles in the article “Which is better. mosaic tiles or mosaics”. We will not repeat ourselves, so we will dwell in detail on the stages of stacking individual chips and homemade glass elements.

Mosaic (chips)

If you want (and know how) to create something original, you can purchase glass pieces for mosaics of all kinds of colors and shades. A real artist can make a masterpiece of them, but those people who do not have such talents can lay out a simpler pattern, as in the photo.

It is important! The work is painstaking and interesting, but to complete it you need to have a lot of patience and a lot of free time.