How to cut the ceiling plinth outside corner

How to properly zazazat corners ceiling plinth. a detailed instruction

The most difficult work in the installation of the ceiling plinth is considered the fit and match corners. For the beginner, this case is troublesome, spoils a lot of materials on the method of trial and error, which can never lead to anything. And on the question of how to properly trim the corner on the ceiling plinth, and we will try to answer.

In order to cut the foam ceiling plinth, use a box cutter.

Based on the ways we will need such tools and materials:

The chair is a very simple and useful tool, which is a kind of tray with walls cut at different angles.

In most cases it is indispensable, because it reduces the likelihood of errors when trimming and a great time-saver. It does not cost much, but it gives you a properly fitted joints, and in the end. a beautifully decorated room.

A box cutter or a metal saw is needed if the room’s corners are not straight, which is often the case. Then the method of marking will come to our aid.

Cutting a skirting board in the outer and inner corners.

Most often we are faced with the need to cut the inner corners of the ceiling plinth, and they are particularly difficult. But there are a couple of secrets that will help us handle this properly. So, if we use a wire cutter, then we need to put it in such a way that its bottom was pressed against the wall just over the right slot with a mark of 45 degrees, and the entire long part of the leaf was on the left.

If it’s easier. the ceiling skirting needs to be placed upside down (the part of the skirting which will be close to the ceiling, in the jig is at the bottom, and the part that will be glued to the wall is at the top). So we made a left hand corner. For the right side we will turn our canvas so that its longest part is on the right, place it a little farther to the left of the slit with a 45 degree mark and also neatly cut.

If you don’t have the crosshairs handy for some reason, but you really need to, you can draw them on the table. To do this we draw two parallel lines along the table at a distance of about 20 cm; connect them in the middle at a right angle and draw two more lines that would intersect with the connecting one at a 45 degree angle (the intersection point of the three lines should be clearly in the middle of each). Further we put a baguette to a necessary line and cut on the same principle, as on a jointer.

Chairs. a device for easy and quick cutting of baseboards.

Another way to cut the ceiling plinth correctly. it is with the help of marking.

It is resorted to when the corners are oblique or blunt. Marking do so: it is necessary to attach a ceiling plinth in that position in which it will be glued, and to spend a pencil on the ceiling a fishing line for a trimmer of its inner edge. Then we attach the second cloth from the other side and do the same manipulations.

Then we attach one cloth at a time and on each skirting board we mark the intersection point of the inner edges of both cloths. Well, it’s a matter of small things. we spend a trimmer line between the marked point and the opposite edge and cut. This method is very useful when all the angles in the room are different, and templates and devices do not fit.

Outside corners are less common than inside corners, and they are much easier to trim. Now we will do the opposite of what we did when we trimmed the interior.

Initially we need to mark where our corner will begin, and for this purpose we put a ceiling plinth to a wall with a marking: now the point of intersection of ceiling plinths will be the upper point of their adjacency, we mark it a simple pencil and we can begin a plinth preparation: for preparation of the left-hand side we place the plinth in a jig so that the baguette top pressed to the wall, bottom. to the bottom, and the long edge was on the right. Again we cut along the slit with a 45 degree mark. The right-hand corner is prepared in the same way, only the long edge of the board will be on the left.

In the case of rounded corners, no devices will not help us and have to do everything by eye.

The easiest way to form such a corner is to cut the skirting board into several parts of about 5 cm each, trim all the parts on both sides and check the joint in place, adjust if necessary and glue them one by one. The pieces that will join the baseboard at the beginning and end of the rounding, leave one side flat. It is important not to mix up the pieces, so you can number them with a simple pencil.

• Do not be afraid that there may be gaps in the joints on the ceiling plinth, because they are easy to putty and after drying and painting are invisible. The exceptions are ceiling plinths made of wood. even putty in tone can be noticeable.
• Try the cuts on the floor, because it is easier than on the stepladder. Do not glue on the skirting boards until you are sure you have trimmed them correctly.
• Do not be upset that something does not work, and the cuts have to be adjusted a few times, have patience and everything will turn out.

As the saying goes, afraid of the eyes, and the hands do! If it is well to think through every movement, there is nothing terrible in the independent trimming of the baseboard, and beautifully decorated room will please the eye of the owner and his guests.

Quality repair involves careful and accurate attention to detail.

Finishing the work with the ceiling, you need to decorate it well. for this purpose, ceiling skirting boards are used. As a rule, the installation of plinths does not cause much trouble, have to tinker with the corners. Let’s consider in detail how to cut the ceiling plinth in the corners, talk about different ways, give useful recommendations

Ceiling plinths of any material can be cut using one of the following methods. They are suitable for all except for plastic: such decorate, using ready-made corners.

The need to trim the baseboards

Installing ceiling plinths (another name. fillets) should be performed by the correct technology. However, there are no difficulties in it. the vast majority of baseboards are mounted with glue. It is enough only to properly lubricate the product and hold it in the right place for a while.

But with how to properly cut the ceiling plinth in the corners, there are questions. When equipping the ceiling there is always a need to handle corners. but their value can have both a standard value (e.g., right angle), and a certain deviation. The latter case is possible if the room has a complex shape, or if the repair was not possible to level it.

Skirting boards must be joined perfectly straight, regardless of the corners of the room. In addition, it is often necessary to cut the skirting boards on the outer corners. To properly carry out such work, you need to stock up on the right tools and understand how to cut the corners of the ceiling plinth at home.

Skirting boards made of foam is one of the cheapest options. However, the advantage in the form of low cost is offset by a large number of disadvantages. In particular, the foam itself is quite fragile and soft material that is very easy to break. Even if you just squeeze such a product in your hand, it can deform.

Because of the low strength of the processing of foam baseboards is very difficult. If the experience of cutting such parts is not enough, then most of them in the process of work will fall into disrepair, so all the benefit of the cheapness of the skirting boards will be leveled. To cut the foam fillets usually use a hacksaw or a well-sharpened knife.

Installation of external corners for the ceiling plinth

To understand how to properly cut the ceiling skirting boards for arrangement of outer corners of the room, it is important to remember that such corners are not common, only in those areas that are equipped with niches or all sorts of protrusions. Mount the outer corner for the skirting board must absolutely follow the same pattern as the inner one (read: “How to make a corner from a ceiling plinth”). The only difference is that the left plank of the skirting board must be cut through the left-hand notch in the jigsaw, and not through the right-hand notch.

In the same way the right baseboard should be cut. It is placed in the jig to the right, pressed to the bottom and side edge, and then carefully cut through the right-hand groove with the hacksaw. “How to cut a ceiling baseboard corner. proven ways and methods”.

It is important to remember that when fixing the baseboard to the outer corner, it is necessary to ensure that its lower part corresponds to the edge of the wall corner.

Trimming the ceiling plinth in non-standard corners

It’s no secret that in many living spaces, especially those being built today, the corners are far from always straight. So, in modern houses, equipped with bay windows and walls of complex configuration, the corners can be, for example, rounded or blunt.

The use of a plough in such a case will not work, so how to properly trim the ceiling plinth for non-standard corners, should take place as follows:

• The baseboard should be tight to the left wall tight to the ceiling, that is exactly how it will be fixed finally. Using a simple pencil, you need to run a trimmer line along the top edge of the baseboard plank.
• Do the same thing, fitting the baseboard to the corner on the other side.

So, we can conclude that it is quite possible to cut the skirting board for the ceiling yourself, it is only important to follow all the instructions clearly and use the necessary tools for this. If in the process of work there are any questions, it will be better to ask for help from the experts, who can always provide a photo of the skirting board options and videos on their installation on the ceiling.

How to cut a ceiling plinth correctly. it is useful to know

• A plier for the ceiling skirting board;
• A hacksaw or a construction knife;
• pencil.

• For cutting the left-hand corner, the skirting board must be set in a jig so that its longer part was on the left, and the part that is planned to cut. inside the jig itself, and it must go into the right slit at an angle of 45 degrees.
• The skirting board must be pressed to the bottom of the tool with the side it will be fastened to the ceiling, and with the side it will be set on the wall. to the side edge of the chair.
• Using a hacksaw or a construction knife, you need to cut the material with a hacksaw. In this case, before you can properly cut the ceiling plinth, you need to fix it tightly in this position.
• The second skirting board should be inserted into the jig from the right side and bring it to the groove at an angle of 45 degrees.
• Next, you need to repeat all the same actions as with the left plank.

• The skirting board must be pressed tightly against the left wall, that is exactly as it will be fixed finally. Using a pencil, run a trimmer line along the upper edge of the skirting board.
• Do the same, fitting the skirting board to the corner on the other side.
• Next, you should take both skirting boards and take turns to attach them to the same corner on both sides, and then transfer to them the point that is formed by the intersection of the lines.
• The mark must be docked with the baseboard corner on the other side.
• Then the baseboard must be placed on a hard surface and pressed against it with the side it will be fixed to the wall, and then trim the corner along the line with a vertically held construction knife.

Response to the post “The price of repair in one room

I did in a crumb-unit 28 meters. Was able to take a fully finished in January.

It was like this. To strip everything down to the ceiling and bricks, to make anew on the approved and coordinated re-planning with the design project.

Different were counted. For example, one foreman said 150002500 (rough materials) per square meter, the other plus or minus a kilometer in a million with nothing.

As a result, decided to do through a firm. Counted the estimate 410 without roughage 15% on top of contingencies (happened, as expected). Drafts were supposed to be 200-250. Bottom line. On all estimates, I paid 715 with roughing materials. I’ve bought quartzvinyl, ceramic tile, light sockets, plumbing fixtures myself

I was very satisfied, I got exactly what I wanted. I won’t overload the answer, but if you want to. I show you pics of the was / is

How to install a chemical anchor? HILTI and others VIDEO!

To mount the building from metal structures, you need to fix the columns on the anchor group. In this case we will consider the installation of chemical anchors. This is the most common and easiest option. details and consider in the article. Whether it’s HILTII or any other anchor. They all have a similar composition. epoxy resin and two-component compound (resin hardener). When you mix the two components is fast hardening, which provides solidification for 180 minutes (in these 3 hours, typed the maximum strength of the composition).

Chemical anchor is:General term, so called steel studs, bolts and rods that are attached to the base, with a synthetic resin-based adhesive system and a second component. hardener (for rapid curing).

Himanker is very effective for heavy loads, as it forms a very strong bond between the metal element and the base material (usually concrete, brick, etc.), which is very difficult to apply.).

The first thing to do is to make a marking at the places of installation of the anchoring group, for this you will need a metal ruler, which will need to mark the axis of the columns and installation.

Mark the place for the holes of anchors, to fix the columns.To speed up the process, I made a template on which to apply the location of drilling and size of the base of the columns. The template is cut out of plastic. It was cut out with a router according to the dimensions in the project on a scale of 1:1

Making a 1:1 scale stencil (for the base)

The stencil. it is a convenient and quick way of marking, I practice it on all new objects,

A convenient and quick way of marking out the base of the columns and future holes

DrillingDrilling is done with a drill, not a core, in order to save money (the core is more expensive). The diameter dimensions are 2-3 mm larger than the diameter of the stud itself. If you touch reinforcement, it’s only then that you need a diamond core bit. You can call a crew that specializes in drilling with diamond core bits, on average they charge from 300 to 750 for each hole.

The depth of installation and the thickness of the base can be considered according to the test table from HILTI, all standards are based on STO 36554501-0482016.

The first method. with a drill bit

Professional power plier with a rotary hacksaw

The chisel usually looks like a tray with vertical holes for the hacksaw. It can be made of wood, metal or plastic. This tool represents the oldest and simplest carpenter’s tool, designed for cutting wooden parts at 90° and 45° angles. There are types of such a device and for professional work, with a rotating mechanism, in which the cutting tool can be rotated and fixed in any position.

How to cut a ceiling plinth properly

Ceiling corners are divided into interior and exterior, the method of joining them slightly different.

If necessary, you can make a jig with your own hands. You will need three scraps of plywood or boards of equal size. First, they are applied in the form of an inverted “U” and make a marking of the corners. Then according to the markings cut notches under the hacksaw almost to the bottom, and the boards are twisted.

Inner corner

• Measure them correctly.
• Set the baseboard plank in the jig so that this position is exactly the same as the placement on the ceiling.
• The skirting board must be pressed firmly against the opposite wall of the jigsaw. Hold and press with your free hand.
• Put the hacksaw at an angle of 45° in the special hole and cut the piece.

When cutting soft materials (PVC, Styrofoam) use a metal hacksaw or an ordinary construction knife. Then the work will be neat and with smooth edges.

Outer corner

• Measure the length of the skirting board from the nearest wall to the outer corner, leave a pencil on the wrong side of the line for a trimmer, marking the desired length. It should be taken into account that the edge (its upper part) should come out a little bit.
• The skirting board is moved in a chair and cut off.
• The adjacent strip must also be measured to a surplus and cut out mirror to the first piece.

Try on the ceiling plinth: the junction of the parts must be perfectly straight. If you have not succeeded and the joints are uneven, you can trim the edges with a regular knife until the perfect join.

The second method. without additional tools

For the inside corner, you can use the easiest way to perfect the joint. by marking on the ceiling. One more example of how to cut a corner beautifully and evenly.

The end result is an even 45° angle if you run a trimmer line from the intersection point to the edge of the piece. Note that the above method of marking works only when the corners are perfectly flat.

The nuances of trimming internal corners

Work on how to make the inside corner of the ceiling plinth, begins with the fact that the product is attached to the ceiling. This is necessary to measure the required length of the part.

When the measurements are completed, place the skirting board in the prepared skirting frame. And place it so that the position of the product is exactly the same as on the ceiling.

It is necessary to hold the baseboard with the left hand and make sure that it is tight to the wall of the device. The piece, which is intended for installation on the ceiling, should be located at the top, and the lower part is pressed to the bottom of the wood cutter.

The blade of the hacksaw is turned at a 45 degree angle and begins to cut. The tool itself is held as close to the left hand as possible, and when cutting do not press hard on it. Once the inner corner of the ceiling plinth number one has been cut, proceed to work with the adjacent product. Cut it similarly, but in reverse, as if in a mirror image.

If the fillets are made of polystyrene foam or PVC, the work should begin on the front side, so that the result is more accurate.

Creating the outer corner

Before you make the outer corner of the ceiling plinth, you need to make appropriate calculations and measurements to perfectly cut the product. To do this, measure the distance the piece occupies from the corner on the outside to the nearest wall.

On the back side of the product, draw a trimmer line, outlining the required length, remembering that its top slightly protrudes outward. After completing the measurements and calculating the outer corner of the ceiling plinth, proceed to further work.

Tutel is placed in the jig and neatly cut off. The adjacent baseboard is measured, just like the previous one, remembering to leave a reserve. It is necessary to cut in a mirror reflection in relation to the first segment.

Skirting boards. fillet

To do it correctly, it is important to strictly follow the existing recommendations and rules of finishing works. And then the result will please you.

In fixing the fillet (so called this element) there are no difficulties: in fact, all varieties of products are attached to a reliable adhesive.

In order to hang a ceiling plinth, even inexperienced repairmen have no difficulty. They are worried about something else: how to trim a ceiling plinth? Virtually every room, no matter how intricately shaped, has corners.

And here in these internal corners, the individual elements of the baseboard must be beautifully and evenly docked. And in rooms of especially complex configuration have to fiddle with the outer corners. Let’s try to figure out how to be in each of these situations, and how to cut the right piece with the tools available.

Baseboard materials and cutting methods

First of all, let’s try to determine what the baseboard can be made of, and what a particular material is better to cut.

On sale today you can find products made of foam (PVC), wood, polystyrene foam and polyurethane.

Perhaps some of the cheapest skirting boards are made of foam plastic, which is a fragile, soft and brittle material.

Even your fingers can leave dents, creases and defects on them easily. It is quite difficult to cut a nice and even corner of the baseboard based on PVC.

Inexperienced craftsman a large amount of purchased material can go to waste for this reason. Also, this polymer has high electrostatic properties, which explains its ability to collect dust.

It is best to cut such a skirting board with a hacksaw or a sharp construction knife.

Styrofoam products are also inexpensive, although this material is more durable analog of the traditional foam.

Can also be worked on with a sharp tool.

Extruded polystyrene foam

Skirting boards made of extruded polystyrene foam are a bit more expensive, they are somewhat denser and more difficult to cut. But they’re much less likely to crumble and break.

Therefore, it is more convenient and easier to cut them. A hacksaw or sharp knife is handy for this purpose.

Polyurethane skirting boards for the ceiling are currently, perhaps, one of the most expensive.

But they are worth their cost: moisture-resistant, quite strong and dense, quite elastic.

Placed over the kitchen stove, the plinth can deform and even crack a little.

They are perfectly cut with a special knife without crumbling. But these products are very sensitive to temperature changes.

Wooden skirting boards for the ceiling are quite heavy and dense products, hard and strong.

They are well amenable to processing with a special fine-toothed hacksaw. You can also use a sturdy metal blade. So how to cut a skirting board properly?

Prefabricated corners

Note that every craftsman has the option of not having to pore over the precise cutting and fitting of corners.

In a construction store you can buy a prefabricated corner element, in which the prepared edges of the skirting can be easily inserted.

It is enough to measure the required length of the workpiece, and cut it at right angles.

All defects and flaws will hide this special element. But such a convenient way to use is not always possible, because the standard sizes of these factory corners can differ markedly from the size of the baseboard itself.

Such corners will stand out for its disproportionality, and it will not look very neat. But if the design of the room and the size of blanks allow you to use this method, you should not neglect it.

Trimming the baseboard

Trimming with the use of a wire cutter

How to evenly trim a ceiling plinth corner with it?

Pliers are simple tools used by carpenters. With its help it is possible to cut any workpiece at the desired angle.

It is usually a wooden, metal or plastic tray, which is made to cut at an angle of 45 ° and 90 ° special vertical slots.

There are complicated designs, on which, in addition to the named angles, there is also a hole to make a 60-degree cut.

For professional work a special plane saw is available. Its swivel mechanism allows you to fix the cutting blade in relation to the workpiece at any given angle.

Inner corner

The prepared skirting board is put against the ceiling, the required length is put aside.

Then this same plank is inserted into the mortiser exactly as it will be positioned on the ceiling. It must be pressed against the far wall of the attachment. Hold the skirting board in this position with the left hand.

The blade of the hacksaw should be in such a position that its angle is 45 degrees, and the handle as close as possible to the hand. Trying not to press the saw, we carefully cut the workpiece.

Next, the skirting board must be cut off the mating strip. It is also placed at the far side of the tool, held and pressed, this time, with the right hand.

Similar to the previous procedure, the position of the hacksaw. its handle is close to the hand at an angle of 45 degrees. The skirting board is cut.

Then ready, already cut planks are docked. accuracy of fit is checked. It is believed that for better orientation, when making an inner corner, it is better to start cutting from the front of the product. The places of cuts usually have to be further adjusted with a file.

Outer angle

The right thing to do, in order to observe the dimensions more accurately, is to start measuring the inside corner first, and only after that move on to the outside corner.

Otherwise it could happen that along the whole length of the plank is not enough.

The strip is attached to the ceiling, and marks are made according to the size. Holding with the left hand, the ceiling plinth is pressed against the closest wall, with the handle of the hacksaw close to the hand. The workpiece is cut off.

The counter slat is pressed against the nearest wall, while holding the right hand. The blade of the hacksaw should be at a 45° angle, with the handle of the tool close to the hand of the craftsman. A piece of workpiece is cut, the corner is neatly docked.

Such processing of the edge of the parts with a mash is good in cases where the angle between the walls is flat and straight (90°).

If its performance leaves much to be desired, it is worth using another method.

Marking on the ceiling

The method with the marking on the ceiling allows you to cut a corner exactly and straight. It has one disadvantage. it is quite inconvenient to hold the plinth plank by weight during the procedure.

In all other respects, with this method, you can estimate the angle for cutting even more accurately than with other methods.

When the skirting board is applied to the proposed place of installation, all size deviations and inaccuracies are immediately visible and taken into account.

Cutting a corner

First you need to take a pair of blanks, then cut them at right angles. Perpendicular to the perpendicular wall at the end of the strip, we put one strip. We outline on the ceiling line for a trimmer on the contour of the baseboard. We remove the first skirting board, then in the same way, pressing its end into the wall, we put a counter skirting board. Mark the line for the trimmer in the same way.

The intersection point of the two separate lines is the mark at which the workpiece is cut. Each skirting board is placed on the surface again, and the point of the future cut is marked on both skirting boards. From the point found to the other edge of the skirting board, draw a line for the trimmer. We cut the skirting boards accurately to the marks we made earlier.

This method allows you to process inside corners more accurately.

Trimming a skirting board without a joiner

Agree, not everyone can find a joinery tool in the economy, and buying it only for the baseboard is not a good idea. But you still need to trim the corners, because the neatness of the ceiling finish is at stake. What to do in this case?

You can actually do without the joiner. There are even two ways to trim the corners of the baseboard without special tools: by resorting to marking on the wall and using a drawn false wood trimmer. Start with the first one.

Do the work as follows. For the inside corner:

• Place the plank to the ceiling, which will be installed to the right of the corner. Run straight trimmer line along the outside edge of the skirting board.
• Apply the plank to the opposite side of the corner and also draw a trimmer line on the ceiling.
• The place where the two lines meet, mark with a cross. Place the trimmer at the corner, transfer the mark to the corner, and then extend a trimmer line carefully to the lower corner of the molding, this is the line you will trim the baseboard on.
• Use a hacksaw or office knife to cut the necessary corner.
• Apply the trim strip to the right of the corner. Draw a trimmer line on the ceiling along the baseboard further from the corner.
• Apply the baseboard to the left of the corner. Draw a trimmer line along the plank to the mark where it intersects with the first line.
• Draw two marks on the plank: the first is the intersection of the lines on the ceiling, the second is where the corner of the room passes. Connect the two marks. you get a fishing line for the baseboard trimmer. Now all that’s left is to cut the corner and, if necessary, correct the gaps.

Trimming a corner with a false chair

The third method of trimming the corner of the baseboard is not quite usual. using a kind of false chisel. You can make such a “tool” in two ways.

The first is to draw a jig. To do this, you can use regular heavy paper or cardboard: draw two parallel lines on the sheet and, using a protractor or a simple angle, set off the corners with the required degree. The corner is cut in much the same way as in the case of a joiner’s plank cutter: lay the skirting board against the “tool”, make the necessary marks and make the cut according to them.

The second way. to make a prototype of a mitre made of three wooden boards: connect them in an oblong shape of the letter “U” and perform notches in 45 and 90 degrees. The same protractor can also be used to mark corners.

A plane made of wooden planks

Cutting the corners of the skirting boards without a notch, it is very important not to miscalculate with the length of the strip and directly to the degree of notch. To avoid mistakes, at first it is better to cut blanks 10 cm longer, then try on the dry to the ceiling, and only after that adjust until you get the desired result. In addition, let’s not forget that not all bathrooms have ideal angles of 90 degrees. you can’t do without making adjustments to the products anyway.

Advice. Fix the ceiling plinth trim to the ceiling only after adjusting to her corner of the next baseboard blanks. It is best to try the cuts on the table instead of under the ceiling itself. it will take more time, but the cut lines will be neater.

Thus, we have several ways to cut the ceiling plinth: with a joiner’s chisel, without a chisel, using a kind of false chisel. Whatever variant of execution of the corners you have not chosen, it is important to do everything accurately and precisely. only then you will get a really effective tool for the final design of the ceiling, thereby making the interior of your bathroom aesthetically complete.