How to cut the ceiling skirting board inner.

How to cut a ceiling plinth in the corners

The quality of the ceiling decoration greatly affects the appearance of the room. Therefore, they try to do everything perfectly, or very close to this. The final bar is a ceiling plinth during the design. They give the finish a finished and holistic view. The strips themselves on even surfaces are mounted simply: on a special glue of white color, but problems arise with the design of the corners. Without knowledge of how to make the angle of ceiling plinth correctly, a lot of material spoils. About how and how to cut it in the corners and tell.

The very first skirting boards on the ceiling were made from gypsum. They were cast in special forms, then on the solution was installed on the ceiling. Called such figured jewelry fillets. Today you can see them infrequently: they are expensive, and outwardly almost no different from cheaper options. And the name is almost lost.

The most popular ceiling skirting boards from polyurethane or polystyrene are most popular today. They are inexpensive, look wonderful, easy to install, have a wide range of profiles and drawings. The width can be from 5 mm to 250 mm. They are used in almost any rooms decorated in any style. Exception. wooden houses with the corresponding interior. Here, most often use wooden products. the style dictates its conditions.

Part of the assortment in a specialized store

There is also a similar plastic finish. It is mainly installed in bathrooms. But even in wet rooms, you can without fears to mount polyurethane planks. they are not afraid of damp.

Cut the ceiling plinth in the corners of any material one of the methods described below. Only plastic skirting boards: such an angle can be arranged only using ready.made corners.

Than and how to cut off

Work with skirting boards from different material involves the use of different cutting tools. When working with a ceiling skirting board made of wood, it is more convenient to work with a wood saw. All the rest, including plastic ones, made of polystyrene and other polymers, are better cut by metal canvas. It turns out a more even cut, less a burr. Saws are usually used when working with a stupid.

Correctly decorated corners look attractive

When working with pairs of foam without special devices, they cut them with a good stationery knife. Its blade is quite thin and even, the cut is smooth, not obsolete. If you work with a polyurethane or polystyrene with a saw, do not press hard: you can mate.

In general, in order to get a little to the tool and material, take some piece and practice it: cut, saw, cut. So there will be fewer problems when working.

Possuts knock: Basic rules for use

Everyone will be able to understand how to properly cut the corners of the ceiling plinth. In order for the process to go smoothly, you should familiarize yourself with the main methods of creating beautiful and even blanks in advance.

The main rule of work is to comply with the inclination of angles. If the baseboard is fixed on the right, then the angle will be cut off on the left side, and vice versa.

Knock. a convenient tool for quick processing of workpieces

Polyurethane ceiling skirting boards: what is the advantages and disadvantages, of which it consists of, what species are, how to choose, step.by.step installation of baguette, coloring, recovery methods, average cost. in our publication.

What is a knock, how to use this tool

Starting repairs in the apartment, many are wondering how to cut the angles of the skirting board to the ceiling. It is important to get acquainted with the rules for using equipment. Fetling is a device consisting of walls with side cuts and bottoms. The part that requires processing is laid out in the middle and adjusted with the help of a file.

The main question is how to cut a plastic skirting board. The result should be a perfectly even angle of 45 degrees. The taller sawing is quickly and easy to use the finished knock, or to make it from the available materials. The tool for reliability is placed on the floor and held with the left hand. The hacksaw must be placed in one of the oblique lines, depending on which angle should turn out. right or left.

It is best for beginner masters to fix the knock on the table so that it does not jump off during work

• With a pencil, a thin, barely noticeable fishing line for a trimmer is carried out;
• The filler is laid by the side in the knock and determine the angle of the cut;
• The hacksaw should pass exactly along the indicated line;
• The second filler is rotated and a cut is made on the other hand, so that when combining two parts, an angle forms.

Before gluing on the ceiling, the fillets should be treated with sandpaper.

Polyurethane stucco molding: what is, what advantages and disadvantages, main types, composition, manufacturers, main selection criteria, stages of independent installation, options with photos and cost.

How easy and easy to make an even angle on a ceiling plinth without using a knock. Even a beginner will cope.

With your own hands

Most often, minor defects still remain.

In this case, the problem is solved usually mounted it just just with his own hands.

Problems arise only when connecting angular compounds.

It is not always possible to make an even angle. And if there is also no special tool, then you can generally come in despair.

There is a simple way to cut angles and without a knock. Which? Consider below.

To smoothly join the planks of the ceiling plinth in the corner, you need

First of all, you need to mark the markings.

We will produce it directly in the corner at the site of the future attachment of the baseboard.

To do this, we apply one bar close to the corner and on the ceiling with a pencil we draw a small fishing line for a trimmer along the skirting board.

After that, from the opposite side we apply the second strip and also draw a fishing line for a trimmer.

At the place of intersection of two lines, put a point.

At this point, the plinth slats from the ceiling will converge. Let’s call her upper cutting point.

Now this point needs to be transferred to the planks of the plinth.

Again, pressing one plank of the baseboard into the corner closely and mark two points on it:

We do the same with the shuffle of the plinth from the opposite side of the corner.

Marking on the strips is applied, you can proceed to cutting the angle.

We place the strips alternately on a solid flat surface and make a cut with a knife on the applied markup.

Then it remains to attach cut strips in the corner and be convinced as the resulting cut before further fixation.

All three methods I described work, the choice depends on what kind of tool you have in stock and what are your professional skills. If after watching the video you still have any questions, welcome in the commentary than I can, I will help.

If you are not confident in your abilities, then both floor and ceiling skirting boards have docking elements allowing you to do without trimming.

How to cut a baseboard in the corners without a bunny

It seems that dealing with the stupid is simple, but the corners are not always equal to 90 degrees. This method will help solve the problem of proper pruning of the baseboard in the corners quickly and without unnecessary troubles.

The procedure to correctly cut the skirting board in the corners without the same:

• Attach a plinth close to the corner.
• Draw a fishing line for a trimmer with a pencil at the top of a plinth.

How to cut the corners of the ceiling skirting board without a bin

According to the text of the article, we will figure out how to correctly cut the corners of the ceiling plinth in the presence of a special tool. a little. Obviously, this useful device is not found in every individual, but for its purchase for a one.time repair. the enterprise is incomprehensible.

If so. let’s try to find out what is initially how to cut the angles of the skirting board without a bunny.

Our goal is to achieve such impeccable angles

For starting to study the materials where our experimental.

To realize, just as and what to cut, it is better to know the density and other features of the material.

• Styrofoam. The cheapest and most weak material; in general, mechanical strongness is not very necessary and necessary, which decorates the ceiling.
• Extruded polystyrene foam is somewhat denser and a bit harder is treated. However, specifically a bit: if necessary, it is cut by a common knife.
• Wood. more severe material in processing. To cut it, only a hacksaw will have to be used.

Tip: it is better with small and frequent teeth. This will make the cut much more even. The metal canvas is also suitable.

Kryzaovka for metal is suitable not so much for wood

At what angle to cut the ceiling plinth? If the passage, if we try to decorate the right angle with a ceiling baseboard (you will not find other corners in many multi.apartment buildings and the main component of personal houses). 45 degrees.

A right angle, broken into two similar sectors.

How to cut the baguette of a ceiling skirting board without chose if you have not 90 ° angles

How to cut a ceiling baseboard at an angle?

In most cases, a light carpenter tool is used for cutting at an angle. a hook. He is a design of duralumin, plastic as it is also called a wooden tray with grooves directing the canvas of the hacksaw at certain angles to the axis of this tray.

How to cut angles with this tool?

• We fix the baseboard in the tray in the same section of the position in which it will be installed on the ceiling. Align it on the side that will cling to the ceiling.
• Cut with a free hand along the guide. For wood, as already mentioned, a hacksaw is used. Case for metal, of course, cut both polystyrene and polystyrene foam. Today, polystyrene plinth foam in other words can be cut off with a knife; But he is obliged to be very sharp. In another way, the material will crumble under the blade.
• A wooden skirting board before attaching to the wall, perhaps, will have to be adjusted with a ratfoll. To fit skirting boards made of softer materials, a sharp knife is again used.

How to cut a ceiling plinth in the corners? An ordinary tool is useful to us. knocking

How to cut a ceiling plinth in the corners? A regular tool is useful to us. knocking.

The cutting of corners is very ordinary for itself; Fear, but, enormous efforts. The foam is just crumbling. Well, a wooden skirting boat with excess interest just split.

How to make the correct inner angle of the baseboard or baguette at home without

One of the simple solutions is to make an analog.

• We make a simple tray of 3 planks.
• Cut it at an angle of 45 degrees. The angle can be marked with a transporter or student.

Read repair electric spaces with your own hands video

It’s not at all difficult to do it yourself. If you have to adjust many corners for you. this work will pay for itself

Many are a tray and without a slot. Make a template of the angle of paper or cardboard (this is especially fundamentally, if the angle is not exactly 90 degrees) and draw a fishing line for a trimmer, why you will have to navigate.

Glide together under the right angle of the plank (in this case, just cost 2, not 3).

• Inbate a ceiling plinth for other tensioning ceilings in an impromptu tray in the same section of the position in which it will be attached to the ceiling.
• Put the tray along the edge of the template.
• Cut the baseboard, taking into account the fishing line for the trimmer drawn on the template. Keep a knife or hacksaw strictly vertically.

The improvised tray will come in handy and then, but you will like it completely at least. Use a table simply moved to the wall or angle between the wall and the floor.

How to cut corners with such a strange inventory?

• Mark on the ceiling, wall on the plinth itself future corners. These are the ends of an imaginary strip that will dissipate both skirting boards.
• Install the skirting board in the tray for sure because it will be fixed to the ceiling in the bedroom or other room, and cut it, guided by the risks applied. The knife on the other canvas of the hacksaw again keep strictly vertically.

How to cut a ceiling plinth in the corners with the least set of tools? Just. Only a pencil, a knife and an eye are needed

How to cut the baseboard in the corners with the least set of tools? Just. Only a pencil, a knife and an eye are needed.

Read how to change the oil pump on the Echo chainsaw

As a result, some tips that may be needed for you before the installation of a ceiling plinth.

• To measure the plinth bar between the 2nd corners, adhere to the usual rule: for the inner angle, the length is measured specifically from it, for the outer corner-from the point that is defended from it deep into the room width of the baseboard.
• Strengthen the plinth bar to the ceiling and wall no earlier than adjusting the angle of the subsequent bar adjacent to it. Trying sections is much more convenient on the floor, and not on a stepladder at the ceiling.
• Get ready to make the slices a couple of times. Stell yourself.
• Do not be afraid to quit small cracks at the corners: they just plunge. The exception is from wood ceiling skirting boards from generous species of wood: due to the texture, even the putty selected in tone will be visible.

Even if you cut the skirting board by weights on weight, the remaining cracks can be hidden by putty

Take into account: in general, all the troubles with the adjustment of the skirting boards of course simply avoid. For angles, inserts are often sold, which are connected to the axis cut perpendicular to the axis with a plinth.

How to cut off a corner with a bunker

In rooms with even corners and walls, cut a ceiling skirting boat with the help of a bin, as a rule, it is not very difficult. The tool has the form of a P-shaped gutter with the guides for a saw at an angle of 90 and 45 degrees. By placing an element that requires cutting inward, inserted into the guides of the saw. In the process of cutting, the baguette must be held tightly in place, in order to avoid defects. It is quite difficult to cut off the baseboard, since it is necessary to achieve its simultaneous fit to two planes. If the width of the baguette is small, then it is more convenient to press it to the near side.

Which one to choose in the store

When choosing a device, you need to focus on its functionality (at what angle and what planes to cut the workpiece) and the volume of work performed. Simple, P-shaped tools are bought if you have to install a floor or ceiling skirting board on their own, rotary are intended for masters. If you need complex, in 2 planes of cut, then the non-professional will have to buy a turning point.

When buying, you should pay attention to the following characteristics:

• the material from which the device is manufactured;
• the width of the base;
• wall thickness;
• the presence of a cutting tool in a set;
• the number of slots (the more there are, the better);
• the presence of clamps (latches);
• how free the progress of the saw.

You can buy a simple device without a hacksaw for 87-820. The cost of a swivel was starting from 1300 to say how much an electric tool costs, even approximately, difficult. The screening of is huge. You can buy a end saw and for 6 thousand And for 25 thousand.

“Fit 41255”. The model is made of durable plastic. There are slots at angles at 22.5, 45, 90 and 135O for vertical cut and 45O for inclined sawing. The price of the tool starts from 335

“Stanley1-20-112”. Material. solid shockproof plastic. Saws can be done at an angle of 22.5, 45 and 90O vertically and 45O horizontally. Allows you to make very accurate cuts. The cost starts from 770

“Zubyr15375-75”. Made of impact-resistant technical thermoplastic resin (ABS-plastic), which allows you to maintain the size of the slot for a long time. You can buy for 220-340.

FIT PRO 41321. Professional turning. The bed can be steel, aluminum or plastic. The saw is delivered in the kit. Costs from 3500 to 6700

About skirting boards and difficulties of cutting angles

A practical decor element. a ceiling plinth or filler. can be made of:

• polyvinyl chloride is the most affordable in price;
• polystyrene foam. have a low cost;
• Polyurethane. cost an order of magnitude more expensive than the rest;
• polystyrene. cost a little more than polystyrene and polyvinyl chloride foam.

A wooden filler who gives the interior of strict elegance is very popular. To make a cutting angle on a wooden skirting board, you should use a hacksaw with frequent small teeth or a hacksaw for metal.

Advice! If a moisture resistant and durable ceiling skirting boards are needed, then you should choose a polyurethane filler. It is important to remember that it does not at all take out sharp fluctuations in temperature. it is quickly deformed, so it is not suitable for use in the interior of the kitchen.

Each of the materials used for the manufacture of skirting boards has its advantages and disadvantages. For example, polystyrene and polystyrene foam. easily break, polyvinyl chloride have increased electrostatic.

Regardless of the material from which the skirting board is made, its cutting on the corners has its own difficulties, since the walls of the room do not always have angles of exactly 90 °. Sometimes, especially in old buildings, the walls can have an angle of 88 ° or 92 °, so by cutting the baseboard at an angle of 45 °, when docking, it will definitely be a gap. To avoid this, use the presented way.

Before gluing the plinth, it is necessary to check if there is a gap in the corners

Working solutions for preparing baguettes without

Another option for cutting the bar is to create a certain design of dense cardboard and wooden bar. First step: you need to bend the cardboard at the angle that you measured in the corner of the room. Then, to the wooden bar designed to cut off the angle, press the cardboard and draw a fishing line for the trimmer along which you need to cut the bar. this will be your template. To cut off the filter, put a wooden template on top of the bar, and cut the required angle along the bar.

The last proposed version of the cutting of the fillets without chusla is the most accurate and simple, but somewhat costly. This is the acquisition of special accessories, which includes ready.made internal and external angles for masking inaccurate cuts. This method has one drawback: the appearance of ceiling strips has a lot of options, so the angles from the set may not be suitable for your cornices. You can buy a ceiling plinth and a set of corners to it in any construction store-the manufacturer usually accompanies its ceiling cornices with such sets.

Actual proposal in the construction market is the Kindecor skirting board from foamed polystyrene, made using extrusion technology. Therefore, Cindecor Ceiling strips have no shortcomings of the cornice PPU. The cost of cornices is much lower than polystyrene or other analogues.

But in old houses with “floating” corners, such sets are unlikely to be useful. in the kit you will find only corners at 45

How to rectify the situation? You need to approximately cut the end of the baguette. an angle of about 45

, and then, for several examples, cut the angle to the required value in place.

When cutting the baguette and forming the outer corner, use the following method:

• Press the baseboard to the right side of the corner so that the bar protrudes around the angle at least to its width;
• With a pencil, mark the fishing line for the trimmer on the ceiling;
• Press the baseboard to the left side of the corner so that the bar protrudes around the angle at least to its width;
• With a pencil, mark the fishing line for the trimmer on the ceiling, mark the intersection point of these two lines;
• Copy the marking on the bar, connect the points with a line, cut the baguette along this line;
• Check the evenness of the cuts by applying prepared baguits to the outer corner;
• Before gluing a ceiling skirting board without bunks, eliminate errors (irregularities, chips, clearance, inconsistencies) on the surfaces of the fillets.

Materials for the manufacture of ceiling skirting boards

What options are possible?

To begin with. a few words about what ceiling plinths can be made from.

The classic material for the manufacture of such elements of interior decor has long been gypsum. It was from it that the various details of the stucco moldings decorated the halls of rich houses and palaces. Gypsum skirting boards, as a rule, had intricate reliefs and different sizes.

Gypsum skirting boards are produced today, but due to considerable cost, heavyness and fragility, it began to lose in popularity to products from other materials

Today, real gypsum products of such destinations are usually made to order, as they have a fairly high cost both in manufacture and installation. Most often they are cast in small batches for restoration work when restoring architectural monuments.

However, the appearance of gypsum fillets is still attractive, as it is an excellent completion of the decoration of premises made in various styles. Therefore, in our time, customers are offered a wide variety of analogues from other modern, cheaper and light materials. polystyrene foam and polyurethane. They perfectly imitate natural gypsum fillets.

Ceiling plinths made of polystyrene foam. by visual perception after completion of the decoration from gypsum, it is almost impossible to distinguish

Such fillets have a number of undeniable advantages. this is small weight, which greatly facilitates their installation, a wide range of relief drawings and width of the strips. They fit perfectly into different design solutions of both classical and modern interior design styles.

The manufacture of wooden skirting boards decorated with carvings is a very time.consuming process, and this affects the cost of such products

It is impossible not to say about wooden skirting boards, since they are quite popular for rooms lined with natural lining, which never goes out of fashion.

Skirting boards from this natural wood or from composites based on it have their advantages. this is durability, the possibility of repeated repainting into various shades and colors, as well as high reliability of fastening on the surfaces.

Wooden skirting boards with various relief drawings are made to order. The disadvantage of wooden fillets can be called their high cost, since very often they require handmade work of the master.

Cutting the skirting board made of any material, as well as adjusting its corners according to the same methodology. The difference can be in the use of tools for marking and cutting, in the methods of attaching fillets to the surface of the wall or (and) ceiling.

Features of cutting skirting boards from different materials

Due to the fact that the materials from which the fillets are made react differently to the effects of cutting tools on them, before proceeding with the cutting of the baseboard, you should familiarize yourself with some features of the process. This information will help to avoid random damage to products.

• The wood can be called the most durable of all of the listed materials used in our time for the manufacture of decorative ceiling strips. Therefore, with its cutting, there is a greater resistance, due to which burrs and chips can easily form on the cut. Wooden skirting boards, especially those that have a small width, must be cut with a hacksaw on wood with small teeth or an electric jigsaw, also with a “delicate” file.

• Polistyle foam (polystyrene) is the most fragile of all these materials, so it can easily begin to crumble. It is best to cut it with a sharp stationery or construction knife. When conducting the cutting process, it is not recommended to press the filler with a blade, since the cut area can be served, which will spoil the appearance of the bar. The work must be done extremely carefully, not in a hurry, not allowing either deformation or cringing on the cut.

Installation of these products must also be carefully done. Polistyal planks are not devoid of elasticity, but it is not so expressed that it would allow skirting boards to completely repeat the shape of an explicitly uneven surface. And with a strong press on the baseboard, it can just break.

Given the shortcomings of polystyrene foam, it is best to purchase strips with a margin, in case of damage. The low cost of such fillets allows you to do this.

• Extruded polystyrene foam is more durable and reliable, it is easily cut and not crumble. It is much easier to cut a baseboard from this material, since burrs or shells rarely form on it. However, as well as polystyrene, they do not have sufficient flexibility, so they are problematic on the curved area of ​​the surface.

Cutting products from this material can be made using a sharp knife or hacksaw for metal, a canvas with small teeth.

• Polyurethane. Both strict and flexible skirting boards are made from it, so they can be fixed to a not very even wall or a curved section of the finish (for example, when framing the arched vault, column, etc.P.).

You can cut flexible products from this material only with a sharp knife, and strict ones. just like extruded polystyrene foam. The cost of polyurethane skirting boards is quite high, so the negligence or errors made can cause considerable unnecessary costs.

How the corners of the ceiling plinth are adjusted

Preparatory work

Before moving directly to work on the formation of angles, it is necessary to take some preliminary measures consisting of the organization of the workplace and the preparation of the necessary tools.

• Ruler, roulette, construction square, pencil.
• Augoter or transporter.
• Chancellery or construction knife with replaceable blades.
• Hacksaw with small teeth.
• Flow.
• Laser level. desirable, but optional.

The knock is not an expensive complex device, so it can be purchased even if it is required for one repair. It will even be good if this tool complements the standard set of home workshop. Fetling is a kind of box, in the walls of which the guide cuts for cutting are made, made in both sides at an angle of 45, 60 and 90 degrees. The tool can be made of plastic or wood. In its bottom part, holes are often provided for attaching it to the workbench. to ensure immobility.

Ways to form angles

As a rule, ceiling skirting boards have a complex embossed surface. It is she who creates difficulties when forming from two of its segments of a right angle without leaving the gaps.

In addition, the corners in the premises of apartments and houses are quite often different from the straight lines, that is, from 90 degrees, which also complicates the adjustment of the skirting board. And it must be cut so that there are no gaps at the junction, otherwise they will spoil the appearance.

Another nuance that is important to consider when cutting the planks is the location of the corners. As you know, there are two of their types. internal and external. Most often, only internal corners are present in the standard rooms of modern apartments. External corners are characteristic of rooms with one or more turns, for example, an entrance hall or a corridor, or in which there are niches or protrusions.

Trimming the baguette for the design of external and internal angles is slightly different among themselves.

Scheme of internal and external angles

There are several ways to achieve an ideal or almost perfect angular joint of the baseboard. In one of them you can use the stupid, in the other to use the laser level, thirdly. marking using a square and ruler. The simplest of them is the first option, but its use is possible only if the neighboring walls of the room form an angle of 90 degrees.

Using the stir

Before starting work, you will have to monitor the perpendicularity of the walls in the corners to measure to make sure that it makes sense to cut the skirting board by the strules. Control is carried out using a large square or a special tool. an angular. Augoter is a professional tool, and not everyone has it, but you must have a square in your household.

Augoter. a device that allows you to accurately determine the size of the angle

If it turns out that the corners are still straight, or are not very different from the desired 90 degrees, then you can safely cut the strips at an angle of 45 degrees, laying them in the stupid. It will be better if the knock is pre.fixed to the countertop. If you allow displacement during operation, then in the cut plinths serious errors may occur, entailing the inaccurate of the joint.

So that the skirting boards perfectly coincide with each other at an angle of 90 degrees, their edges should be cut in a mirror display at an angle of 45 degrees. They can be cut both separately and at the same time, a package.

• When choosing the second option, the strips must be folded together with the back side to each other, and then fix it in this position in several places with stripes of painting tape. If the skirting boards are not fastened, then when cutting a package of their displacement cannot be avoided.

• If the decision is made to cut each bar separately, then they are laid and cut alternately, but when cut, they are laid in the opposite direction. That is, one baguette is cut off on the left guide cuts of the stir, located at an angle of 45 degrees, and the second. on the right.

• The next step, two cut slices must be combined with each other. First, the check is carried out on the table, and then installation is carried out under the ceiling in the trimmed corner. Only by applying the baguette to the place of future installation can you see the real picture. If small errors occur, then the ends of the baguette segments should be adjusted using a sharp knife.
• Only after the strips are ashamed as much as possible, they can be fixed to glue.

As for the difference in the performance of cuts made using rushed for different types of angles (external and internal), it is well shown on the submitted schemes below.

Demonstration of examples of cutting cuttet using the internal and external angle of ceiling plinths

If you carefully study the schemes, you can see that the cuts are made from different sides of the edge of the baguette, that is, for the inner angle, the hacksaw is installed at an angle of 45 degrees from the main surface of the bar to its edge (if you look from top to bottom), and for the outer corner. on the contrary. on the contrary.

Making a bunker or template

If the corners in the room were even, but there is no stir at hand, then such a device or a simplified option. the template can be made independently. You can make it in several ways.

First option

If the knock is required for constant work, and there is no opportunity to purchase it for some reason at the moment, then you can make such a tool from plywood or well-processed board. For this purpose, you will need to prepare three wooden details. The walls should have a size of 500 × 100 × 15 and 500 × 80 × 15, and the bottom part is 500 × 200 × 20 mm. Different wall height will contribute to a more comfortable cut of details. A peculiar box without end walls will be assembled from the parts.

Ready.made corner elements

In order not to trim the ceiling skirting boards yourself, you can use ready.made solutions. In any construction store you can find factory products, already at the factory made at a certain angle. Such an angular element allows you to combine the edges of the plinth, simply cut off at a right angle. Corner details allow not only to connect a filler in the corner of the ceiling, but also to hide the defects of the cut at the edges of the parts.

Unfortunately, this method is not relevant in all situations. The dimensions of the angles produced at the factory are adjusted to certain standards. but the skirting boards themselves are far from always complying with the standards. Of course, such details can be combined, but the result will look unaesthetic. If there are no angles of the right size on sale, then you still have to engage in pruning skirting boards on your own.

Wood

Ceiling skirting boards made of wood differ from analogues. The wood has a fairly large weight, which affects the mass of products from it. The skirting boards are ultimately quite dense, very resistant to mechanical damage and solid, which allows you to not be afraid of random deformation during installation or cutting.

To cut a wood filler, it is best to take a fine.toothed hacksaw designed specifically for thin work with this material. However, a good option for metal is a good option.