How to cut the platbands in the film. Video: how to cut the wood -fiber panels wall stove

How to cut dates from wood.fiber slab for door passages cutting platbands

To change the size of the door leaf, the following tool is required:

• Cutting tool. Depending on the material of the door and the degree of shortening are used: a hacksaw, a hacksaw for metal (suitable for plastic), corner grinding, a rubbish, a milling mill, a circular saw, an electrician.
• Clamp. It is necessary to fix the canvas during operation.
• Hand tool for refinement: carpentry knife, chisel, files, hammer, screwdriver, Kerner.
• Sandpaper for finishing processing.
• Measuring tool: roulette, metal ruler, square.

Depending on the design of the door and the coating, consumables should be prepared in advance:

• Glue. PVA, carpentry, epoxy, special glue D2 for wood, “moment” or other varieties.
• Wooden bars and rails of different sizes.
• Maslar tape and metal guides for the direction of cutting tools.

To restore the external coating of the canvas at the pruning site, you will need varnish, veneer, brown tape and other materials. You can fix errors and minor defects using putty.

Most often, doors shorten in height. For this, first of all, it is necessary to determine which side it is better to do. from below or from above. The decision is made after careful measurements and taking into account the location of the loops, which is undesirable to rearrange.

If the groove is not in the box, but the opening is very deep and does not overlap with a simple dose, you can choose any of the options below. If you want to clarify something, contact me!

The selection and installation of dobges on interior doors in 4 versions

Cutting technology and the cutting tool used depend on the size of the cut strip.

• To shorten the canvas by 0.5 or less, the professionals use a fugging machine or electric fugus, but at home they are rarely available. You can use a regular rubbish (fugan). With a decrease in height, an electric jigsaw or hacksaw with small teeth is more often used. In the end, the end is polished
• With the size of the cut within 0.5–1 cm, manual circular saw is used. When cutting with an electrolobian or hacksaw cut, it turns out uneven, which requires subsequent strict. This circumstance should be taken into account when cutting, taking a supply for strict.
• Reducing the size of a hollow (frame) canvas by 1-3 cm requires preliminary reinforcement of the structure. You will have to partially disassemble the canvas at the pruning site, and install the enhancing bars, fixing it with glue or brackets. Cutting itself can be carried out by the same tools as in the previous case.
• When cutting the frame bar with 3-5 or more cm, it is necessary to strengthen the frame. The width of the rack is restored using an additional beam, which is firmly fastened to the remnants of the previous structure and is associated with perpendicular elements. The new design is carefully enhanced by glue. An extra strip of wood.fiber plate is sawn off with a hacksaw or an electrician. At the ends of the wood.fiber slab, a chamfer is cut off. The place of cutting the canvas is polished.

Profiles

If you look at the dilutions in the section, you can also find differences. There are two types of them: simple and type (or telescopic):

• Simple ones have a rectangular cross section and are a regular even bar with or without decorative coating on the front side. Their standard thickness is 10-16 mm, the width varies from 30 to 200 mm for different manufacturers, and the length corresponds to the height of the door frame-from 1900 to 2300 mm. Иногда простые доборы выпускаются с неотделанной торцевой кромкой.
• Telescopic premise for the door: what is it, you can understand if you know how wall panels or boards of lining are interconnected. At one long end, he always has a groove, but another groove, a straight edge or a comb another.

note! Such submission can only be installed in boxes with a groove cut at the factory and framed by Mr.

If you want the door block to look like a monolithic structure and not be lost in the opening, it is recommended to purchase additional panels. If you want to clarify something, contact me!

Cutting methods of laminated wood-bruise without chips

Speaking laminated wood-based stove at large enterprises in woodworking is carried out on a special format-sprinkle machine. Small workshops producing furniture also acquire this, but it is expensive, therefore, as a home tool is inappropriate. If the question arises of how to cut a laminated wood-bruise plate without chips, then as alternative methods for cutting, you can choose sawing using a hacksaw, circular, milling cutters for laminated woody plate or electrician.

Using a hacksaw

Drinking a wood-brown stove without chips with a hand hacksaw is not easy to also saw a laminated wood-brown plate with a jigsaw. Although this is a cheap and affordable way.

First you need to cut a fishing line for a trimmer with a knife, draw with a nail or awl, and then stick the masking tape, to protect the upper laminated layer. Then at an angle of 30 degrees carefully, without pressing, cut the material. The selected hacksaw saw should be with small teeth so that the cut is as even as possible.

The hacksaw can leave damage, which is eliminated using a tape grinder, exhibited perpendicular to the subsequent outskirts.

At the final stage, it is worth treating the sections with sandpaper with a flexible profile.

Electric

Often for cutting, laminated wood-based plate is used by an electrolobian. The main condition to carefully cut off the stove. small teeth.

The electrolobian saw will not be able to replace the disk saw, t. to. It is mainly used as a cutting tool for small sections of plates. They need to work without strong pressure, smoothly and not too fast. If the cutter of the laminated wood-brown plate has no experience, then small chips may appear on the back, but with practice the quality and appearance of the saw will improve.

Circular saw

If the question arises, how to cut the wood-based slab and which tool to choose, then the circular is quite suitable. It is also often called a disk saw. This is a disk tool mounted on the table. Many are interested in which disk for the circular saw to use. The circular disc is needed with small teeth. Cutting is better than when using a jigsaw.

For greater accuracy, you should mark the guides, and also not work at too large speeds.

With the help of a cutter

The milling cutter is used not only to cut the plates, but also when drilling holes, cutting grooves, creating edges, etc. P. With it, you can perform a figured cut. The tool is used with the jigsaw. The plate is first sawn with a jigsaw, and then a milling cutter with a bearing is used, giving a cut the necessary depth. How to drill, cut and saw slabs with a milling cape are known to professional sawing men. Using this tool, the cut is absolutely even and neat. However, this is very time.consuming, requiring increased attention and special skills (for example, setting a template for a cutter to a drilled or other surface), the process that without experience is better not to take such work, and order the sawing to specialists. In some workshops, such a service is provided. The main supplier of wood mills is Topvoltage, ordering their tools from them, you can do this with delivery.

Cut formatically cutting machine

The use of the sawing machine guarantees the accuracy of the saw and the complete absence of chips. Such machines are used in production and are considered specialized equipment.

• Carriage. Allows the movement of the mobile table, but the plate is fixed in the right position.
• Saw node. It has two flat metal disks: the first makes preliminary cutting, the second. drains completely through.
• Stanin. The mechanism is fully relied on on it. Eliminates vibration and adds stability, which is important for the quality of the cut.

Three desktops: 1st: location of the knot. 2nd (mobile): supply of plates for sawing. 3rd: maintaining sawn parts.

Types of sawing machines depend on the time of continuous work:

When setting up the machine, they matter: the depth of the cut; plate position; The corner of the cut.

• The plate is motionless to the table (mobile carriage);
• The workpiece is positioned according to the size ruler and the saw node is launched;
• когда диск наберёт нужную скорость, стол будет двигаться вперед вместе с плитой-заготовкой и попадать на него.

The use of format-sprouting machines is advisable for mass production, and not for isolated cases. For a one.time independent use, you will quite select the tool easier or order a cut to specialists.

Drinking with cutting

• Tire. the ruler is fixed to the plate using a clamp on the marking line;
• along the line, a cut is preliminarily made on one side with a depth of about 0.1-0.3 cm;
• Further on the other hand, the plate is cut completely through and through.

If everything is done carefully, then no chips will appear.

Programs for cutting

You can make a laminated laminated wood-piece stove from a sheet in special programs on a computer. Among the most famous of them: “Astra cut”

In the program file, an order that may contain several products that have a set of parts, the parameters for which are set by the user. Based on information on the cutting of the edge of the plate, such as cutting, cut width, through cuts, etc. P. The program generates the cutting card. Then the specification, sketch and other technological documentation will be automatically formed. The program includes reference information about materials, operations, edges and details.

Suitable for those who are constantly engaged in the work on cutting a wood-based slab. This program:

• supports multiplayer regime;
• systematizing and sorting information;
• Sort orders for archival, planned and active;
• saves information about materials and so on;
• takes into account the remainder of the material.

In the editor you can see which part is laid correctly, and which is not the remnants of both significant and not very. The user can change the settings for ease of work.

The editor window is divided in half: on the left. sheets for cutting, on the right. columns in order to set parameters to future details: the amount of color and size and size. The program includes the “rotation” mode in three versions:

1st: The program itself has a part during rotation; 2nd: all the details that are the same, rotate together on the sheet; 3rd: Details do not rotate.

The cutting map is created using the “Calculation” command. If you repeatedly set this command, the program will offer new options that can be changed manually: rotate and drag the details.

Universal Rezak

The universal cutting is called differently. He has many manufacturers. When we bought our tool one of the leading manufacturers was Bosch.

The tool is notable. But having bought it, to do something else, you can no longer.

The cutter, unlike all other tools, makes oscillatory movements.

We use mainly two main types of files: wide. 25mm40mm and narrow 10mm20mm.

Very often during installation, you need to cut the PVC panel in place. Often this can only be done by the Boshevsky Rezak. You can’t crawl into complex places any other tool.

The cutter greatly simplifies the work and accelerates it. You can cut wall products along and across. You can even cut the upper or lower layer of the panel.

Let’s talk about the minuses. The price of the tool and consumables go off the way to it. For example, a jigsaw file will cost 100r, and a cut for a cutter in 800r. Files quickly become unusable.

Cutting panels at home

Handle a sheet with a hand-cutting plate or a laminated wood-bearing plate. True, at the same time, you are unlikely to avoid the appearance of chips and burrs, but you can try to reduce their number and size.

There are several rules that should be followed by cutting panels of the wood-based slab:

• Cutting sheets must be done on a flat solid surface. For sawing large panels, two large tables can be adapted (their height should be the same!);
• In order to exclude the appearance of chips, stick a sticky tape or good masking tape along the cut line, which will hold the edges of the laminated layer;
• For sawing with a hand saw, select the canvas with Melim tooth. The teeth of the saw should be sharpened well. You need to conduct a saw with a slight pressure, at an acute angle to the surface, constantly controlling its position;
• for cutting the plates of the wood-brown slab and laminated wood-bearing plate using an electrician fishing line for the cutting trimmer should be scratched or even cut. It is best to use a sharp knife to cut out a durable layer of laminate;
• Install a file with a small reverse tooth;
• Select the maximum speed of the jigsaw, turn off the “pendulum”;
• Fasten a flat rail along the cutting line and lead a lobby strictly along it;
• the jigsaw should be tightly pressed to the sawing surface.

All these recommendations help to properly cut and cut the wood-brown slab, but chips, nevertheless, cannot be completely avoided. Therefore, if it is so important to get a perfectly smooth, even fishing line for a trimmer of cut, without chips and traces of a saw, you should contact specialized workshops, where you will cut out any figure for a moderate fee from a sheet.

How and what to saw plywood and wood-bruise without chips: straight and curly cut.

The end saw is an “domesticated” and a strongly reduced copy of the horizontal machine. To cut a wide sheet of wood-brown plate or laminated wood-bearing plate on it will not be possible, but it will fully cope with small details.

Ensuring a perfectly clean cut

For most parts, it is enough to reduce the size of chips to 0.2-0.5 mm. Such minor irregularities of the overwhelming edge are not striking, if desired, it is easy to eliminate them by removing the chamfer with an emery bar or covering up with a wax pencil. It is also possible to polish the end with sandpaper, if during cutting a sufficient allowance value was given.

Nevertheless, even at home, it is really possible to achieve the quality of the cut, comparable with the result of the work of the cutting machine with two high.speed discs. This is possible only when the tool is moving along the guide rail, in extreme cases, on a temporary stubborn bar.

First, you need to make two gaps with a depth of about 0.5 mm on both sides of the part to indicate the thickness of the saw. On the edges of the cut line, you need to scuff two furrows under an even ruler. This is done either by a segmented or oblique boot knife (for wood-brown stove and wood without covering), or a sharpened drill or a winning cutter (for laminated materials).

The depth of the furrows should be at least half of the thickness of the outer layer, heterogeneous in relation to the main array of material. This method requires a high accuracy of comparing the furrows and cutting line, but only in this way it is possible to provide a perfectly even trimming end that does not require additional processing.

This is done either by a segmented or oblique shoe knife for a wood-bruise plate and wood without coating. either a sharpened drill or a winning cutter for laminated materials. If you want to clarify something, contact me!

How to cut the platbands on the door correctly?. Doors, partitions

We will show you how to put door platbands, how to work with a gun, explain various nuances of work.

Marking and trimming platbands

First of all, before installing, the platbands must be torn. We take four platbands and end. The center of gravity of the platband can be determined by putting it on the finger. When the Reika balance, we determine its center of gravity. Cut and carry the platbands to the door.

Any door has a radius of rounding. There are straight platbands, but very rarely.

Here we put the platoon flush, even a little shifting it inside the door to hide what is under it.

You need to install the platband from the place where the radius ends:

Put two marks above the door. We do this by eye, but you can measure this roulette.

The angle will turn out at 45 °, that is, the mark will be at a distance from the edge of 5-7 mm. It is impossible closer, because there is a loop here, and closer to the beginning of rounding, it will not allow you to make a mark. Focusing on the radius, we make a mark with a knife.

On the other hand, there is a response, and it is also not to move it closer. Do not forget to numb the platbands.

We remove garbage from under the platbands so as not to cut off more from the rail than required.

Where the radius is over, put the mark. We measure similarly and on the other hand.

From the part of the inputs, everything is much easier. Again, we do not flush, but a little with a displacement. We put the mark not along the good, but a little below.

Accordingly, the same thing on the other hand is 1 mm below:

Similarly, we make marks on the platband. not flush, but with a slight displacement. We carry out the trimming of platbands under 45 °.

There are situations when the wall is not entirely flat. in some places it performs, and then when installing the platbands, a non.storage is obtained. Sometimes it happens that the platbands must be a little overwhelmed when they are not flush, but shifted inside. That in such cases it is necessary to do? Imagine that we have a wall on the right, and on the left is the door. It is necessary to nail the platband to it.

If we cut down the plane, then when nailed the corners will disperse. How to deal with it?

Here we have a hole of about 2 mm. If we fill it out like that, we must also cut off, that is, make some kind of lining.

Our wall rises by 2 mm, and we must put some 2 mm high under the corner.

If the gap is obtained from the back, then the front is the platband without cracks in front. This is if the door is drowned inside the opening and it turns out on a ledge. In such cases, it is necessary to take into account the rear gap. the protrusion of the wall. Then we saw off long rails.

Installation of platbands

Now we will work with a pneumatic microshpiller. a gun, the air into which is supplied from the compressor. With it, we will attach the slats to the wall with special nails. hairpins.

Dried foam should not be ripped off, but cut off with a knife.

We apply foam to all other platbands:

The foam will create a certain layer, and the platband will not hang out. Since the wall is not entirely flat, all irregularities need to be compensated by foam. You can wait up to three minutes so that the foam forms. A small film will allow the rake to stick quickly.

A guideline is rounding on the platband. The corners of the upper rail, of course, are better not to beat, but to put long rails, and already determine the position of the upper one. where to lower, where to raise. We had a small tubercle under the platband, but it is practically not visible, and the discrepancy between the platbands is small.

Net up one nail below. Then we have frozen foam, which does not allow Reyke to hang out, but where it hangs, we fasten. We advise you to score nails after 20 cm. It is better not to score them at the eye level, otherwise such a nail will be too noticeable. In our case, this is a microshpilka, it can be lubricated with wax, then it will not be visible at all. It is advisable, of course, to fasten the platbands from the ends.

However, there is one important point. since the pistol uses lubricants such as oil, then when firing on light wallpaper, air is released, and an oily spot will fall on the wallpaper. Therefore, when you nullify, put a piece of paper. The microshpilka is good because it breaks easily. If the microshpiletor is not pressed when firing, the gun leaves and, accordingly, a hat remains, which does not clog, because it is very thin and bends.

In such cases, we clamp it with pliers and tear off with rotational movements.

It makes no sense to pull it out, because there is a hole, and you will never score a hairpin in this hole.

Nuances when installing platbands

Here we have either the platbands are slightly different, or the master did not set the corner of the corner. Such irregularities can be rounded with a hammer. it is only good that the client does not see this.

This is how the angle is rounded so that the tip is not visible. Therefore, it is better to cut the angle first, measure 90 °. If it turned out a little less, finalize with a saw.

Let’s say a few words about the oily spot on light wallpaper. It is not visible on the dark wallpaper, and the whites can be seen very well. Suppose this is our wall, we shoot. and here is our oily spot:

Now let’s talk about nails on nailed platbands. This nail is practically not visible, but it is, and some do not like it. In such cases, take an acrylic putty, pick up the color of a tree and apply it to a nail. It is advisable then to remove acrylic, and completely, since it may turn slightly when it dries.

In fact, all these holes are visible at the time of acceptance, and after operation of the doors after 1-2 months, you simply will not see these holes. Try to remove acrylic right away, otherwise it will be difficult to wash it off then. Another moment from practice. Wooden platbands are, of course, cool, but not practical. It is better that the platbands are made of wood.fiber slab.

The tree has one feature. from a change of humidity it turns it.

If the wooden platband is beaten on a premium without foam, then over time, after six months, especially in the off.season, it begins to twist and the run of the angles begins. Plates made of wood.fiber plate to such climate differences do not respond. they will not lead them.

Another moment in relation to nails. For white doors, never add Hi-Gear to the gun, no other grease. Shoot the gun somewhere so that the whole grease comes out, otherwise there will be a black spot on white and bright doors, which will be very noticeable in contrast.

How to cut the platband with a bunker

The main advantage of the struck. it was marked in advance angles. Due to this, performing manipulations is not so difficult.

Cocking the platbands along the rushed lines can be as follows:

The slots are quickly shaken under the influence of the saw, so this is a one.time tool, but the price will allow you to stock up for the future.

This procedure can be very tiring, but necessary and effective. However, despite all your efforts, certain gaps between the platband and the frame may remain. In this case, it makes sense to use silicone or acrylic sealant of the corresponding color. Some suggest using fugu to seal such cracks. Be that as it may, it makes sense to remember that it takes time to solidify these materials. That is why, in order not to get the frame and platbands, pushing them with preliminary painting tape.

Accuracy and quality

Formato-sprouting machines for sawing laminated wood-bearing plate and wood-brown stove have high quality cut, which allows you to reduce subsequent costs for the processing of cuts (grinding, elimination of chips and burrs, and so on). That is why on such machines you can carry out a cut of any complexity and configuration, which means almost inexhaustible opportunities in the production of furniture. Fantasy children’s furniture, convenient countertops of computer tables, curly end.to.end carved jewelry in the door of the kitchen facades. all this is possible when using machines.

There are two types for cutting panels:

• Vertical, which are a strong strict vibration.resistant welded bed (frame), installed vertically with a backward deviation by 50 °, with guides located above and below, along which the saw beam moves. It is a bracket for a saw block, which moves along the beam down and up, and also rotates by 90 °, which allows you to make both vertical and horizontal cuts. The accuracy of the cut is amazing. For sawing a laminated wood-brown slab, as well as solid, wavy or porous plates, a special cut node is used. The speed of rotation of the saw reaches 15 thousand revolutions per minute;
• Horizontal, consisting of a table for a slab, carriage for moving a saw along a saw mechanism and the actual saw mechanism consisting of one or two cutting nodes. The cutting nodes themselves are equipped with the main and corrugated saws. The principle of action is simple: the main saw is deeply cut through the stove is the wood-bruise plate, and the subceptive accurately and clearly cuts the lower edge (veneer or laminated surface). The saw node can also be tilted to 45 °.

How to choose the installation option and what tools need to be prepared for work

There are two ways to fasten the planks: on the crate and directly on the wall. Assess the condition of the kitchen. If there is very little space in it, it is better to plaster, primed the walls and choose the second option, as the first takes away the tangible area.

If the room is medium or large, you are lucky. You can do without serious additional work and mount wall panels on a wooden frame. Even the wallpaper is not necessary. True, if there are many fat spots or even mold on the surface, it is better to process it. Another advantage of the technology is that you can hide the wiring inside.

List of tools

• Brows, rails or metal profile, if you make a crate.
• Primer, plaster, brushes, spatula, etc.D., If you need to close irregularities.
• Insulation, if necessary. Foam or other thermal insulation material is suitable.
• A hammer.
• Electric.
• Electric screwdriver.
• Hacksaw.
• Pencil or marker.
• Building level and roulette.
• Stapler.
• Liquid nails or dense glue for wood. Sometimes sheets can be attached to them.
• The square.
• Brackets and nails.
• Klyimers for wood.fiber slab.
• Self.tapping screws.
• Self.tapping screws or dowels for a crate.
• Ladder.
• Skirting boards, platbands, corners.

This set of tools is suitable for both plastic structures and for elements made of wood-fiber slab, wood-bruise.

Safety precautions

Do not forget about safety precautions!

When cutting plastic panels, especially using an electric tool (jigsaw or corner grinder), is highly likely that sawdust and fragments will fly away from the material. Therefore, it is worth in advance to purchase protective glasses and gloves that protect the eyes from injuries, and it is recommended not to remove them until the end of the work.

Regardless of what tools you decide to use, the above tips will help you avoid the mistakes of most inexperienced finishes and create a cozy interior that will please for many years.

How to cut the plastic panels along and down, cut the holes Dmitry Korneev, blog low.rise country

Regardless of what tools you decide to use, the above tips will help you avoid the mistakes of most inexperienced finishes and create a cozy interior that will please for many years.

Not every corner grinder is suitable for cutting panels. She must be small so that you easily hold it with one hand. The large corner grinder cannot be used.

The thinnest disk 0.8 mm, 1 mm or a maximum of 1.2 mm is installed in the corner grinder. The disc is used for metal.

The corner grinder gives an amazingly even cut, without a zazubrin and, as they say, the people are “snot”.

Corner grinder does not tear plastic. No matter what part of the panel you cut and in what weather. Both in the cold and in the heat. using a corner grinder, you will get an even cut.

Using a corner grinder from the wall panel, you can cut down literally millimeters.

The disadvantages belongs to the fact that it is heavier than the jigsaw and even more so the knife. But the biggest minus is the corner grinder gives a lot of fine dust. She gets to all places.

Installation of a wood.fiber plate only at first glance may seem difficult, in fact, the whole structure is assembled similarly to a children’s designer and even one who has never picked up an instrument in his life is able to radically change the situation. If you want to clarify something, contact me!

How to cut a wood.fiber slab panel at home?

The universal cutting is called differently. He has many manufacturers. When we bought our tool one of the leading manufacturers was Bosch.

The tool is notable. But having bought it, to do something else, you can no longer.

The cutter, unlike all other tools, makes oscillatory movements.

We use mainly two main types of files: wide. 25mm40mm and narrow 10mm20mm.

Very often during installation, you need to cut the PVC panel in place. Often this can only be done by the Boshevsky Rezak. You can’t crawl into complex places any other tool.

The cutter greatly simplifies the work and accelerates it. You can cut wall products along and across. You can even cut the upper or lower layer of the panel.

Let’s talk about the minuses. The price of the tool and consumables go off the way to it. For example, a jigsaw file will cost 100r, and a cut for a cutter in 800r. Files quickly become unusable.

How to bend the panel of wood.fiber slab?

It is far from always necessary to clad only a straightforward surface, in the presence of imagination, in the room you can create decorative elements of a semi.oval or round profile that significantly diversify its style, but what to do with panels of a wood.fiber slab, having only a rectangular profile?

As it turns out, the bending of this finishing material is quite possible, but subject to the use of the thinnest panels, with a thickness of not more than three millimeters and only for painting.

For bending, you will need a template, it can be made with your own hands, in this capacity any material that can convey to the panels the radius of the circle equal to what has a lined surface.

Since the wood.fiber plate has a structure in its density located between plywood and cardboard, then for bending you will need to soften it. This can be done with alcohol glue, water.based solutions such as PVA are not useful here, the product may swell from them.

A layer of glue is applied to each panel with a gear spatula, after which it is laid in a stack when the pile is typed, it is tied at the ends, laid on a template, after which the endings are pulled and fixed with force.

Drying lasts two days, then the panels are disconnected, polished and stained.

You will also be useful to a video on how to mount a wood.fiber plate panels

Handle a sheet with a hand-cutting plate or a laminated wood-bearing plate. True, at the same time, you are unlikely to avoid the appearance of chips and burrs, but you can try to reduce their number and size.

There are several rules that should be followed by cutting panels of the wood-based slab:

• Cutting sheets must be done on a flat solid surface. For sawing large panels, two large tables can be adapted (their height should be the same!);
• In order to exclude the appearance of chips, stick a sticky tape or good masking tape along the cut line, which will hold the edges of the laminated layer;
• For sawing with a hand saw, select the canvas with Melim tooth. The teeth of the saw should be sharpened well. You need to conduct a saw with a slight pressure, at an acute angle to the surface, constantly controlling its position;
• for cutting the plates of the wood-brown slab and laminated wood-bearing plate using an electrician fishing line for the cutting trimmer should be scratched or even cut. It is best to use a sharp knife to cut out a durable layer of laminate;
• Install a file with a small reverse tooth;
• Select the maximum speed of the jigsaw, turn off the “pendulum”;
• Fasten a flat rail along the cutting line and lead a lobby strictly along it;
• the jigsaw should be tightly pressed to the sawing surface.

All these recommendations help to properly cut and cut the wood-brown slab, but chips, nevertheless, cannot be completely avoided. Therefore, if it is so important to get a perfectly smooth, even fishing line for a trimmer of cut, without chips and traces of a saw, you should contact specialized workshops, where you will cut out any figure for a moderate fee from a sheet.

The selection of panels for interior wall decoration depends on many conditions:

• What are your material resources?
• What tasks are solved by highlighting the capabilities of the material.
• What decorative load will the cladding in the design project collide.
• How important the additional properties of the plate will be for this room: moisture resistance, fire resistance.
• Does the protective (decorative) coating of the plate value in accordance with hygienic standards have?

The best choice of wall panel (780 kg / m³), ​​in appearance and assortment that corresponds to the tastes and capabilities of the owner.

Sphere

In rooms with constant humidity. bathrooms closed pools. the material shows increased fragility.

The wood.fiber plate of the panel has found its application in various areas, in construction, for the manufacture of cabinet furniture, in the design of the premises, the manufacture of arches, partitions and much more.

Maybe you want to know how to make an interior arch yourself? Read here.

Make your methods of fastening wall panels made of wood.fiber slab

The most common stunt is the alignment and simultaneous design of the walls. They are covered with boards of wood.fiber slab.

Wall plates can be attached to the wall in two ways:

On a wooden box

The panels are attached to a wooden box with a section of 20×40 mm. on horizontal logs with locks. Why drive small cloves into the corner of locking grooves. For accuracy, a metal drummer is used, which allows you to clog cloves on the cover itself.

On a metal profile

For fastening the panel for a metal profile, the following deliveries:

• SD profile (3 m) for racks;
• UD profile (3 mm), guide;
• straight suspension;
• additional levels and angles for joints;
• corrugation (self.adjacent) for wiring.

Walls of wood.fiber plate do not require special preparation, if if necessary they are additionally insulated.

Determines the position of the sheets (laid plates, strips) on the wall.

Marking wall levels, screws and nylon threads for guide profiles UD implemented. Open wiring zones are displayed on corrugation.

Construction of a metal profile frame for wood.fiber slab:

• The UD profile is attached to the ceiling and floor dowels (wide side to the surface);
• suspensions under SD profiles are attached to the walls using fasteners;
• SD profiles are attached to the ends of the floor and ud ceiling profile; fixed in suspensions with a step of 60 cm; The vertical position is checked by turning;
• Additional horizontal profiles are installed using crab compounds on vertical racks in places of a possible blow: at a distance of 60-70 cm from the floor and between them.

Fastening MDF panels to the frame using clamps and small screws, in the sequence: panel, groove at the end, fastening with screws to the profile. The corner joints are covered with additional details made of PVC.

The first panel is additionally fixed with screws in places that will be hidden at the end of the work: to the floor (under the basement) and to the ceiling (under decorative trim).

This video is a good example of how you can decorate the wall with panels of wood.fiber slab with your own hands.

Without a frame

The fastening of frameless panels to the “liquid nails” has become even easier. The adhesive consistency should ensure adhesion and filling out unevenness on the wall. Successful adherence to the technology is enough instructions on the tube.

Primer. A prerequisite for the process. Application of glue to the panel is carried out carefully and in stages.

It should be glued in two stages, after the initial pressure on the wall, the panel breaks (for weaving glue) and again (after five minutes) you must constantly glue the panel. The entire process is controlled by the level of construction.

The panels must be cut evenly and accurately to ensure aesthetic joint of the joints.

to prevent damage to the front surface when cutting the plate should be placed on the desktop with a glossy side up.

For a docking in the corners of the walls, use an additional element, on sale. A special corner for external or internal angles.

Wall decoration with panels made of wood.fiber slab. A simple task for anyone who has experience with tools and is not afraid to acquire new skills. The result will delight you and your family.