How to cut the side trim on a door evenly

Trim on the door: The easiest way to make a 45° cut. even without experience

Often during the repair you may encounter a situation where it is necessary to saw off a piece from the part, at an angle of strictly 45 degrees. Usually this is needed to connect two parts at right angles, 90 degrees, such as: door trim, baseboard, furniture and more. An experienced craftsman, professionally engaged in repair work, can often do without special devices, and practically by eye is able to evenly and clearly cut the necessary part. But if you are a novice repairman, and you have a desire to do the job as efficiently as possible, without damaging expensive parts, then you just need to buy a plier. a special device that allows without special tricks to saw off the material at a given angle.

For work you need to have: a plane, a hacksaw, a protractor with a pencil, a piece of wood, an electric screwdriver with screws or a screw clamp.

How to make a proper butt joint

If after gluing a part of the baguette remained some distance to the corner, you need to think about how not to make a mistake. a small margin of error does not hurt. At first it is better to cut a piece with a good margin of about 10-15 cm. Then, having cut off a corner by any convenient method, make its fitting on a dry surface. To do this, place the bar to the ceiling and mark the point where the boundary of the shortening will pass. Trim at a right angle.

Equally important is the correct joining of the corners. Ready-made skirting boards are usually fixed at an angle smaller than 45 degrees, so there may be inconsistencies trimmed edges and the appearance of gaps. Here, the initial trimming of the corners is followed by a dry, possibly exact joining of the skirting boards already on the ceiling itself. Problems usually arise when using wood and plastic materials.

After finishing the rough joints of the fillets, they should be glued or screwed, and then, if necessary, use putty and then. seal all the existing seams.

Easy installation of door trims with your own hands (3 important tips, without which you can not)

Doors are considered the face of any room. At the same time, they can not always really decorate the appearance of the entrance structure, if they will not be installed decorative elements. Trim strips help to provide the door frame with aesthetic appearance, hide all the defects and are considered to be the final accent in the repair. That is why before installing them it is important to understand the correct and accurate preparation of the strips on the entrance elements and to understand the details of the installation process.

The installation of the skirting board is carried out at the end of the renovation

What is a door architrave: materials of making

Decorative elements, which main purpose is to cover defects appeared after installation of the door, are called architraves. Such trim panels create a beautiful frame for the door leaf, close gaps and nuances between the wall and the frame. They should be chosen according to the texture, width, and color, but necessarily according to the door leaf. Materials for making architraves can be wood, plastic and wood-fiber board.

It is possible to decorate an opening without door trim. But otherwise a necessary element.

Facing the door construction with trim panels and architraves

If there is a difference in the installation of door trim from different materials?

Experienced craftsmen give preference to door products made of laminated and veneered Fiberboard or PVC. They are practically unaffected by external influences, have a long service life and are extremely durable. In this case, depending on the material of manufacture, the installation of door trims will be different. Wooden structures can be mounted on liquid nails or mounted with thin nails without nails pins.

If you will use nails with nail heads for installation, the fasteners should be slightly sunk, and their locations should be sealed with acrylic sealants in tone.

Liquid nails for mounting are used only if the walls are leveled. Otherwise gaps will appear. Plastic panels are usually fastened with glue. It is desirable to glue flexible door molding to walls with minor irregularities. As for the fiberboard, which looks almost indistinguishable from wood, it is more difficult to install. Holes for nails are drilled in them beforehand in order not to damage them. And the holes are not made through, but with a diameter of about 1 mm.

Installing the 45-degree trim. the principle

This butt joint with end trimming is the easiest and most common. It involves trimming the joints of the individual parts of the door set at an angle of 45 degrees. Thus it is possible to install any shape of trim. Finishing door openings with architraves allows you to completely hide the jamming places, as a result the design looks beautiful and harmonious.

Installing door trims at an angle of 45 degrees

Installing door trim at an angle of 90 degrees. the principle

Such a notch is used when the shape of the door trim is flat and looks like a rectangle in the cut. In this case the position of the joints does not matter. The joining of the strips is performed at right angles to one another, and the upper edgebanding must be installed between the two side bandings. Thanks to this manipulation is much easier to perform further trimming and adjust the joints.

Installing the telescopic trim. principle

In cases where the walls are uneven the best solution will be telescopic casings. Such strips have a ledge, located perpendicularly to the front surface. It fits snugly into the frame groove or arch support. Finishing with a telescopic element consists in installing the blank of the required length into the groove.

How to cut the door trim properly

Carrying out repair work in the apartment. Owners are often faced with the need to renew doors. It is worth noting that the replacement of the door unit is in any case a significant expense. But replacing the door trims will cost much less. The quality is maintained at the proper level. Installing door trim is not too complicated a job.

Professional tools for installing doors

Before you start installing the door trim on the door, you should stock up on the necessary tools:

• tape measure;
• flat-tooters;
• Jigsaw or fine toothed saw;
• trim;
• hammer;
• Furniture nails;
• construction angle;
• Pencil.

Installing the door trimmers

First you have to dismantle the old trim. Use a crowbar and an ordinary screwdriver for this purpose. You need to gently pry under the trim and remove it. Try not to damage the door frame. After you remove the door trim, remove the existing nails.

After that, inspect the filler trim (it may also need to be replaced). If you need a new strip, then first look at how it is fastened. This element can be fastened in different ways: with screws or with an overlap.

How to install a trim strip. Measure the required width of the filler strip with a tape measure. Trim is fastened by means of grooves: measure the distance from the edge of the wall to the groove. The strip is attached to the overlap: to the width of the filler trim should be added approximately 3 centimeters.

These values are used as an example when selecting a strip in a store.You have decided to install new filler strip? First you have to dismantle the old trim. New filler strips should be installed before installing door trimmers. We recommend buying factory filler trim, as only they have high quality tiled edges.

The standard width of this element is 15, 10 and 5 centimeters.

Buying trim must take into account the unevenness of the wall. If the wall is not completely flat, you should measure the maximum protrusions adjacent to the door. Thanks to this you will avoid discrepancies in the filler trim.

Installation begins with the right and left-hand side trim! Any surplus parts (along the length) should be trimmed.

To fix the filler strip to the wooden frame with wood screws.

The same principle is used for fixing the upper trim. Once the upper filler strip is installed, the entire structure must be strengthened. To do this, the side and top strips are fastened to each other with self-tapping screws (so that they do not come out on the front side).

Then the door trim is installed. It is recommended to mount them at a distance of 0.3. 0.5 cm from the inside edge of the door frame.

Install the door trim along the perimeter of the doorframe. Installation begins with any long trim.

Before installation the architraves should be filed at an angle of 45 degrees with a jig saw or a jigsaw.

Mark the cut lines both with the trimmer and the angle piece.

Once the marking has been made, you need a pencil to draw a neat even line for the trimmer. This is where the sawing is done. It is necessary to saw smoothly and evenly.

Then you need to determine the length of the architrave. This parameter is equal to the distance from the bottom edge of the upper trim to the floor base plus 0,5 cm.

Measure the door trim and saw it off.

Fix the strips on the door with a hammer and nails. nail heads should be bitten off (so that they do not attract attention). Drive nails in 50 centimeters increments.

The hardest part is measuring the top flashing. A shorter door trim is needed for this. One corner must be filmed (as described above) at a 45 degree angle. After that, try on the resulting trim and on the second side mark the top of the corner. Now fasten the element.

If in some places the joints are not all the way together, they need to be sealed with sealant.

On the opposite side of the door, the architraves are installed accordingly.

“All ingenious is simple”, so they say, and with such a phrase we would like to begin this article. Installing the trim causes many difficulties, or rather the difficulties associated with the junction of cuts of vertical and horizontal trim. The junction should be smooth and should not have gaps. There are several ways to file the corners. One way is to use a “Chisel”.

This device is very simple and not expensive, and very easy to use, but as practice shows, not always effective. When using a “Chisel” a person must be skilled at it. There is also a more advanced “Chisel” that can be handled by someone who is not skilled in sawing. With an advanced “Chisel” you can make a very even cut.

For craftsmen who are directly involved in professional carpentry work, a more sophisticated tool, which is called a “Face saw” is sold.

Now let’s see how to correctly fit the trim pieces to each other so that there are no gaps between them. To do this work, you will need to take two side trim, put them on the frame and make a pencil mark the place of the bottom corner sawing. The file must be 5 mm thick. above the door frame itself. Side trim has a right and left hand corner cut. After sawing the side trims, you need to nail them to the door frame. To keep the nail heads out of sight, we bite them off with a pair of wire cutters.

To make the distance between the trim strips was the same, we cut a certain length of plank and measure the distance from the bottom up, or vice versa. The architraves must be installed at a distance of 5 mm. from the edge of the frame. The most difficult thing is to saw down the top platband. Usually the strips have a certain length for sale, about 2.20-2.30 cm. Basically everyone has a standard door, from 70 cm. up to 90 cm. If you have a standard door, you need to take the architrave and saw it in half. That way we will have two upper blanks for the door.

Next, we take the workpiece and file one corner, and then put that corner to the vertical trim and watch to make the angle of the top trim coincided with the side trim, as well as being equal to the vertical and two trims. Now, we need to mark exactly the second corner of the upper flashing to size. We flip this casing “upside down”. Then we put the edge of sawed edge of the upper flashing on the edge of the corner of the vertical flashing, as shown in the photo.

Necessary tools

To properly and accurately carry out this procedure will need:

• Chisel. Do not know how to cut a trim at an angle of 45 degrees. with its help. It helps to cut the product at the right angle. Can be wood, plastic, metal. Looks like a box.
• Hacksaw. For metal, plastic will do for a metal hacksaw, for wood. only for wood. You need to properly sharpen it, so that the cut turns out even.
• Nails/liquid nails.

If you can not use a jig, you can do with improvised materials: pencil, ruler, cardboard, hacksaw.

How to cut the trim yourself without the help of a chisel

How to cut the trim on the door without using specialized equipment. a question that worries many beginners in the construction business. To do it is more difficult, but, it is possible, if you carefully follow the instructions:

• Take a sheet of cardboard, draw an even square, hold the diagonals, bring the lines of the sides of the square to the end of the sides of the sheet. This is a makeshift ceiling, suitable for filing a right angle.
• Put the casing on the square’s bottom line and saw where one of the diagonals crosses it. This is the bottom border.
• Put the other one to the left side of the square, saw where it touches the same diagonal.
• Repeat steps 2 and 3 for the top and right hand counter trim.

How to cut a square trim yourself without the help of a jigsaw

How to cut a plank on the door without the use of specialized equipment. a question that worries many newcomers to the construction business. It is more difficult to do, but, it is possible if you follow the instructions carefully:

• Take a sheet of cardboard, draw an even square, draw the diagonals, bring the lines of the sides of the square to the end of the sides of the sheet. This is a makeshift ceiling, suitable for sawing a right angle.
• Put a platband to the bottom line of the square and saw with a hacksaw where one of the diagonals crosses it. This is the bottom edge.
• Put the other to the left side of the square, saw at the touching point of the same diagonal.
• Make step 2 and 3 for the upper and right hand architraves.

How to properly saw off a door trim with your own hands: instructions and video

Many people, installing a door, wondered how to cut the trim. It would seem that there is nothing complicated about it. As not everybody can cut platbands evenly, it is worth to learn the basic methods. When sawing uses a plane, protractor, improvised materials. Saw them in two ways. under 45 and under 90 degrees.

Necessary tools for cutting architraves

To properly and accurately carry out this procedure, you will need:

• Chisel. You don’t know how to cut a 45-degree angle trimmer. with its help. It helps to cut the product at the right angle. Can be wood, plastic, metal. Outwardly resembles a box.
• Hacksaw. For metal, plastic is good with a hacksaw for metal, for wood. only wood. It is necessary to correctly sharpen it, so that the cut turns out even.
• Nails/liquid nails.

If you can’t use a ruler, you can use other materials at hand: pencil, ruler, cardboard, hacksaw.

How to cut a trimmer with a wire cutter

The main advantage of the wire gouge is that the corners are pre-marked on it. Thanks to this, it is not so difficult to manipulate.

To cut the trim strips along the lines of the jig saw, you can do the following:

Slots quickly loosen under the influence of the saw, so it is a one-time tool, but the price allows you to stock up.

How to cut the trim yourself without the help of a jig saw

How to cut the cash on the door without the use of specialized equipment. a question that worries many beginners in the construction business. It is more difficult to do, but it is possible if you follow the instructions carefully:

• Take a sheet of cardboard, draw an even square, draw diagonals, bring the lines of the sides of the square to the end of the sides of the sheet. This is a makeshift ceiling, suitable for filing a right angle.
• Place the trim on the bottom line of the square and saw where one of the diagonals crosses it with the hacksaw. This is the bottom edge.
• Put the other to the left side of the square, saw at the place of touching the same diagonal.
• Do step 2 and 3 for the top and right hand vent.

How to saw a proper way to cut door trim at home step by step

Purpose of the trim

Why do you need a door trim? Or, as it is properly called. casings. There is no difference. Both on the door and on the window, the installation of the trim is the same. The architraves make the door complete. As they cover the gaps between the wall and the door frame.

How to correctly nail the obnalichki on the door independently

Plastic architraves are fastened with mounting glue. Wooden and wood-fiber board ledgers are fastened both on glue, and on special furniture nails. Such nails differ from standard nails in the fact that they have practically no head, only a slight thickening. Thanks to this form, the nails are practically not visible on the surface, and the thickening contributes to a tight fit of the board.

Preparation for work

Before you nail the lining to the door, you need to prepare the tools and material. From the tools we will need;

• level;
• tape measure;
• hacksaw;
• Jigsaw (a special device for cutting corners);
• hammer;
• building pencil.

Of the materials we need to prepare;

• platbands;
• furniture nails or mounting glue (it varies, but the principle of action is the same);
• furniture putty. It is useful for sealing the joints. Usually the putty is selected under the color of the outlining;
• filler strip.

Before nailing obnalichki at the door, you should check the door itself with a frame. For this purpose it is necessary to take a level and once again to remeasure planes on a vertical and horizontal. After all, installing the trim, it’s the final stage of the door installation.

Features and recommendations

Experts and connoisseurs advise to perform this kind of work with the help of electric jigsaws already because the usual hand saw is too rough. It does not allow you to cut the material evenly enough.The correct sequence of steps is as follows:

Preparation of tools (ruler, electric jigsaw, measuring tape, awl or other sharp device for drawing on the chipboard);

supplementing these tools (if necessary) with an angle piece to make right angles;

measurement of the desired part (with a reserve of 0.2 cm, so that you can adjust);

The actual sawing of the cuttings of the mowing line;

Finishing the place of sawing with sandpaper;

Sawing a casing along (telescope)

If the quality of the face is very poor. mashing it with a chalk similar in tone to Woodchipboard.

Two ways of sawing down the outlines, easy and simple!

Hello, dear friends! In this article I will tell and show you how you can easily file the nailers at 90 degrees, for finishing doors or anything else. Interesting, then let’s go!

A hacksaw (preferably with a fine tooth, the cut will be thin and accurate)

The first method with a mitre saw.

I divided our trim, for example, into four equal parts of 30 cm. I put one piece on the trimmer table, turned on the laser line for the trimmer, turned the saw around 45 degrees and made the cut. With the second piece, I do the same thing, but, set the saw to 135 degrees and make the cut, done.

The second way of sawing without a mitre saw.

I think this method will be more interesting to you, because not everyone has a facing machine. Until a while and I did not have it, nothing cope with hurrah! So we take two pieces of our obolichnik (it is desirable their ottorzivat preliminary having marked their corner), we put them on each other and overlap them on the sides and on a corner that all was smooth on it evenness of our saw cut depends. We put, aligned and marked with a pencil

Next, we take our angle and run a straight line for the trimmer from the corner to the mark

All the marking is ready, the floor is in the hat! Now we take a hacksaw with a fine tooth (I once sawed a hacksaw on metal, tired of course, but the cut was so clean), and slowly do the cut along our line, keep everything tightly and then the hacksaw will play and can leave scuff marks. Try to cut at an angle as sharp as possible, it will make the cut smoother.

Sawed off, now do the same with the second piece. Combine the two pieces into a single corner and enjoy what you see! That’s how easy and simple, without filleting can make the angle of 90 degrees. Thank you for your attention, happy repairs and see you soon!

How to install the strips on the interior doors?

When installing interior doors with his hands to fix the wood or fiberboard trim glue, nails or screws. But we have to keep in mind the evenness of the walls and the shape of the slats. At the joints should be no gaps. If the walls adjacent to the end of the door frame are uneven, then it is better to refuse to glue.

Installing the trim begins on the side where the interior door opens. This is due to the presence of hinges that prevent flush fixing of the strip with the frame element. It will be necessary to make the same indentation, moreover on all three sides for symmetry. Where there are no hinges, there is no need for a mandatory indentation.

If the door is situated in a corner, it is installed in L-shape. If you want you can saw the element vertically and use a narrow strip.

If the door is placed in a corner, it is installed with an “L” shaped arch on one side.

Connection at an angle of 45

When you want to install the platband on the door at an angle of 45 degrees, for the marking use a plier. This jointing of elements is usually used for curved and rounded slats. If you do not have a frame, you can use a protractor to mark it.

The installation procedure consists of the following steps:

• The height of the vertical elements is measured from the floor. Planks are put on the flooring from below, that’s why the joints of baseboards and door trims appear on the side. When installing the trim on the door on the hinge side, take into account the width of the indentation. Measure on the workpiece and put a mark. This will be the bottom point of the angle of 45 degrees.
• Inserting the bar in the jig, mark out from the point put a line for the trimmer cut at an angle. The surplus part is sawn off.

Joining at an angle of 90

Fixing the trim at 90 degrees is done with horizontal or vertical joints. The choice depends on the owner’s preference. When the installation of the door trim with their own hands at a right angle, blanks use only a flat form. The cut areas are treated with varnish or paint on the acrylic basis.

To mount the strips on the interior doors with the imitation of the lintel, the upper element is lengthened. The joint is obtained at a 90-degree angle with horizontal seams. The upper slat protrudes beyond the vertical.

Telescopic architraves

Telescopic architraves can be installed on the interior doors without nails. Decorative elements are equipped with a special lock, consisting of a slot and a groove. Fixing is carried out to the box butt-end. The main requirement for the proper installation of the trims is the presence of the ledge. It is formed when the door frame is already the thickness of the interior partition. Adjacent walls must be even, otherwise you will get an ugly gap.

Instructions on installing the plastic trimmers

Glue is used very rarely, the connection turns out unreliable. Basically, plastic trim on interior doors is put with a profile. This method of installation consists of the following steps:

• According to the size of the door frame cut a special profile. Plates can be made 5 mm shorter. It will not play a significant role, they are still hidden under the lining.
• On the two sides of the interior door, 4 long and 2 short elements are cut. Cut off the joining ends at a 45º angle.
• Fix the mounting profile to the door frame with self-tapping screws. This will not work with cheap Chinese doors. The frame is made of thin metal, and it is impossible to tighten the screws firmly. In this case, the mounting profile is fixed to the wall, but it must be strong, preferably without plaster.
• Begin to screw in the profile from the middle, moving both ways. Use plumb bob or level to fix all the distortions.
• After installing the mounting profile measure the height of the side trim elements and saw off the ends at an angle of 45 degrees. The process is identical to that for wood or wood-fibreboard strips. The workpieces are inserted into the groove of the vertical mounting profiles where they can move.
• Place connectors. angle fittings. in the cut of the architraves. Measure the upper slat and saw off at an angle of 45 degrees at both ends. Workpiece is docked with connectors to the vertical trim, snapping into the mounting profile. Corner fittings completely hides the joint, even if there is a gap.

If plastic trim to put on the wall, facing with clapboard, then wooden rail is fixed along the perimeter of door opening, and already to it fix a profile.

Installation with special nipples and self-tapping screws is possible.

Connecting at an angle of 45

To cut the decorative trims at an angle of 45º a special construction tool is used. the plier. A similar technique of joining two separate elements is applied if they have an indirect form.

• Height of a vertical panel from the floor is calculated beforehand. The lower end of the platband is placed on the flooring, respectively its junction with the baseboard is obtained from the side;
• When installing decorative trims on the door hinge side, the width of the indentation must be taken into account. The resulting figure is applied to the workpiece. this is the lower mark of the corner 45º;
• Next, the bar is inserted into the jig, from the drawn point at an angle, a fishing line is drawn to trim the execution of the cut. The excess part of the casing is cut off;
• The pre-cut billet should be nailed in 2 places, and it should bend at the top. Use wire cutters to cut off the nail heads. One nail is hammered a little bit higher from the ground, the second one a meter from the floor. The length of the nails used should exceed the thickness of the casing by about 5 mm.

Little tricks

When choosing wooden architraves you should pay attention to the quality of drying boards. Poorly dried wood:

Not to spoil the workpiece, the measurement of the length of the trim should be performed with a reserve of not less than 1 cm, which will be useful when fitting the corners of joined parts.

It is easier to cut off the surplus from the opposite end of the trim.

It is not necessary to use a moisture-resistant marker for marking on the front side. It will be difficult to remove the drawn lines with an ordinary eraser.

It is better to cut the trimming of the architraves with a trimming saw.

It ensures a clean cut without chipping. It is easier to neatly touch up the cut corners with a belt sander. With its help, you can achieve a perfect match in the corners.

If during the installation of trim on the door formed gaps, they can be made virtually invisible, using a mixture based on beeswax, which is available in construction supermarkets.

When heated and made to a plastic mass, it fills in the gaps perfectly.

Visually, it looks better trim, towering above the door opening of 10 centimeters, and uniform style rooms in the apartment will provide the same trim on all doors.

Block: 7/15 | Number of characters: 1307

Some practical tips

Nail the first nail in the middle of the architrave, it will allow you to rotate it a bit for a tight connection in the corners of the architrave. Only after all the corners of the door are laid properly, you can drive nails to fix them. The distance between the nails is approximately 15÷20 centimeters. You should check the distance by lightly tapping on the architrave. You will immediately recognize the places where there is a loose fit on the casing, hammer in additional nails.

If the nail is bent all the way in, do not pull it out. Gently grip the remaining part with pliers, rotate it left/right until it breaks off. Why it is not necessary to pull out? The nail could not hammer for “good” reasons beyond your control, which means that the second in this place to the end will not go. It is much better to nail a new one next to each other, there will be fewer holes in the platband.

Increase the tightness of the adherence of the casing across the width can be foam. Apply it to the back side of the moldings in a thin stripe all the way around the wall and allow three to four minutes for it to partially dry. Otherwise the foam will not stick to the surface. Next arrive the casing in the recommended manner. After the complete drying of the foam gently cut off the visible part, the gap can be sealed with sealant. Although, if you do not overdo it with the foam, it should not stick out. During pressing, the foam’s ability to increase in volume is greatly reduced.

Give practical tips for working with a pneumatic gun. It is designed in such a way that there are holes on the side for air exhaust. The piston is permanently lubricated with machine oil, while the air escapes its smallest particles. When the studs have to be driven into the end of the casing, an oily stain is always formed on the white wall from the escaping air. Be sure to put clean paper between the gun and the wall.

Makita AF505 pneumatic nail gun

If you have white casings. do not oil the nails, the oil will leave a stain in the place where the nail enters.