How to disassemble the rogue of the Viking lawn mower. Semi -automatic coils and how effective they are

16th February 2023

Trimmers for Viking (Viking) grass: features, overview of popular models

Many, having developed a factory fishing line for a trimmer on a recently acquired trimmer, try to rewind a new one, but they can’t, because they don’t know how to wrap a fishing line for a trimmer on a coil (coil). There seems to be an instruction, but it still doesn’t work. Let’s try to deal with this problem in this article. So, in order to rewind a fishing line for a trimmer, you first need to remove the coil from a trimmer for grass. It will be more convenient. The removal method will depend on the type of trimmer for grass.

Remove the coil of the trimmer for the grass

On small electric trimmers with the lower engine position (when it works underground), the coil usually has two keys on the sides. We click on them and disconnect one half of the coil body from the other that remains on the trimmer. Together with the first half, the inner part is removed, on which the fishing line for a trimmer of hair growth is directly wound. Be careful when analyzing: there is a spring inside that can fly out and get lost.

On curved trimmers with an electric and gasoline drive (it is still impossible to hold such trimmers for grass), you need to grab the coil body with one hand and start rotating the lamb on it with the other. It is he who attaches the coil to the trimmer. Having unscrewed the lambs, carefully remove the whole coil, trying not to lose the spring inside.

On electric and gasoline trimmers with a straight rod and a gearbox at the ends (except for wire on such trimmers, you can also install a knife), find a hole under the coil, insert a screwdriver into it, for example, turn quietly, until the screwdriver penetrates even deeper, and the coil is not Fixed. Now turn the entire coil clockwise (since the thread is left) and remove it from the trimmer for the grass. Then disassemble the coil. This can be collected by locking or twisting with the lamb. If the coil is on the latch, click on the side sides of the base of the latch so that they bent and free one half of the coil body from the other. We just twist the lamb. There may also be the third type of connection between the two halves of such a coil: it should be captured by the lower part by one hand and the upper part of the other, and begin to rotate them in opposite directions. When disassembling such a coil, it is also necessary to make sure that the spring has not been lost inside.

How to replace a fishing line for a trimmer for grass for grass with a chain from a chainsaw: We increase the effectiveness of the tool

Many owners of gasoline trimmers probably noticed that when using an instrument near stumps or trunks where young shoots of plants are found, a trimmer for grass does not carefully eliminate this shoot, more often in cases where there are many of it. To get rid of it, someone tries to use knives, but they are not adapted to thin plants. As one of the alternative options, you can consider the replacement of a trimmer fishing line for grass with a chain from a chainsaw. However, some subtleties of safety for the tool and a person working with it should be taken into account. You can learn about all the advantages and disadvantages of such a replacement from the sections below.

than 200 types of trimmers in one place at the lowest prices. Press and see

Now, having removed and dismantled the coil, we will begin, in fact, to the winding.

Winding process

If your coil is designed to work with only one antenna, then everything is simple. It is necessary to rewind 2-4 m wires (depending on the size of the coil), find the hole that holds the fishing line for the trimmer on the inside of the coil, insert one end of the mowing fishing line there and begin to wind the fishing line for the trimmer in the direction of the rotation of the coil on the trimmer in the direction of the rotation of the coil. On the inside of the coil, as a rule, it is indicated by the arrow in which direction to wind the fishing line for the trimmer. Having wound a fishing line for a trimmer, we leave a small piece to open it. We fix this piece in a special groove located on the inner side of the coil and designed so that the fishing line for the hair trimmer does not spin when collecting the coil. If there is no such groove, you will need to hold a fishing line for a trimmer of hair growth with your finger to prevent it from spinning with the further assembly of the coil. Then, take the outer part of the coil and pass the outer part of the hair into the available hole, collect and set the coil back to the trimmer for the grass.

If the coil is designed to work with two antennas, then follow the following actions. Inside the coil we see how many grooves are available for winding a braid fishing line. It can be one or two. If there is one groove, then both antennas are wound along one groove. If there are two grooves, each antenna is wound on its own groove. The coil with one groove should have a through hole in which the fishing line for the trimmer is inscribed. Wine 2-4 m of the cutting element, pride it through this hole so that on each side of the hair is protruded equally. At the same time, we wound two antennas of a mowing fishing line of hair in one direction, the opposite direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a small hair line for the trimmer promoted, fix the ends in special grooves, and if they are not, we hold our fingers. Insert both ends into the holes on the body of the outer coil. We collect the coil and attach it to the trimmer.

If there are two grooves, add a piece of braid fishing line of hair 2-4 m long, insert a loop obtained at the bending point into the groove between the two grooves and at the same time wrap both ends of the braid fishing line in each groove in each groove. The following steps are similar to the previous version.

There are also coils on which the fishing line for the trimmer is pierced through the through hole inside. After that, the ends of the cutting element, without winding, are completely stitched through the holes on the outer body of the coil, collect the coil and press the button, which is usually pressed so that the mowing fishing line can be released during the operation. How they wear. Turn the button. The fishing line for the trimmer is wound inside. At the same time, the turn in the “wrong” direction will not work, since it can only rotate in one direction. If you set up, you can wind a fishing line for a trimmer on such a coil without even splitting it. You just need to connect the through hole of the inner drum with holes on the outer body of the coil, and then insert a fishing line for a trimmer into them.

How to change a fishing line for a trimmer in a trimmer for grass

How to change a fishing line for a trimmer in a trimmer and which is better to choose

Since the choice of a trimmer for the grass we saw in the previous article, now we will tell how to correctly refuel a trimmer for the grass with a fishing line, and which is better to choose based on the criterion of work.

After you purchased a trimmer for the grass and began to use it intensively, at some point the question will arise about the substitution of the fishing line, since this is the most weary element in the tool, the rich operation of the trimmer for the grass will often lead to replacement of consumables.

What types of forests I am

The most common type of fishing line, which is suitable for almost all types of coils. a round cross.sectional cord. How to correctly change the fishing line for a trimmer in a trimmer fishing line for a trimmer must be changed. For thick grass. How to remove the head with how to change a fishing line for a trimmer in a trimmer. Therefore, first it needs to be opened. This is a regular fishing line for a trimmer suitable for mowing of juicy grass, but it will be much more difficult to mowed with dry, and even more so it cannot cope with the shrub.

As a rule, the diameter that can mow young grass does not exceed 1.6 mm. How to remove to change a fishing line for a trimmer and is the only right solution for mowing grass in. How to change a fishing line for a trimmer in a trimmer and choose a fishing line for a trimmer for a trimmer for grass of dry grass just in. The thicker the thread, the more rough grass it is able to overcome.

There are fishing lines with sharp faces in the form of a sprocket or square, this option is more adapted to mowing dry grass just due to the existing sharp faces, but its lack of wear is more wear and it is inferior in strength to the round cord.

There are fishing lines with improved aerodynamics with characteristic dentes, scales and notches, a similar product makes less noise, but they use it only on benzos, since the output of such a thread from the coil is difficult, it is most often used with disks in which segments are inserted. How to replace a fishing line for a trimmer in any trimmer disadvantage of such a product is its fragility.

Most often in gasoline trimmers with an engine of more than 1.5 liters.With. Apply cords with a metal cable inside. How to wind a fishing line for a trimmer to a trimmer coil for grass. Trimmer fishing line and stronger. For trimmer for grass 2016. Which. How to replace a fishing line for a trimmer in a champion T266 trimmer, such a thread is ideal for mowing dry grass and small shrubs. electric. Fishing line replacement in how to lubricate it correctly which fishing line for a trimmer for a lawn mower. How to change a fishing line for a trimmer on a material for refueling in a trimmer for grass. The presence of a core, positively affects the wear resistance of this material. The disadvantage of such a cord is its price, which is significantly larger than the above opponents.

How to refuel a fishing line for a trimmer to a trimmer coil for grass

In order to wind a fishing line for a trimmer, it will take about 10-15 minutes. What is the coil of a trimmer for grass? Plastic case with a cassette inside, on which there is a special hook for convenient winding of fishing line. Almost all the coils of the trimmers have a similar attachment principle, this is a central screw-button, when pressed, it becomes possible to stretch the fishing line for the trimmer of the required length. The photo below shows several examples of various coils for trimmers.

Bobbins of the trimmers, the motor of which is located near the ground, have a different fastening to the rotation axis, they have two buttons on the coil located on the sides that need to be squeezed, the rest of the thread is no different from the other cassettes.

The principle of proper winding of the fishing line is similar in all of the above cases, so for example, consider the standard option with two antennae.

To remove the coil with a fishing line, you must unscrew the screw in the center, but keep in mind, the thread there is left, so you will have to twist clockwise, it is specially so that it does not open under the influence of centrifugal force during operation.

Next, using the screwdriver, disassemble the head and remove the coil, on which the fishing line for the trimmer is directly wound. I had to take a trimmer for the grass. It is enough to process grass in the garden and how it is. Having measured the required length and folding it in half, you need to tuck a fishing line for a trimmer into a coil, bringing it out, as a result, its ends opposite each other (for this there are special slots for fixation).

How To Restore A Junked Lawn Mower. For Cheap.

After that, it is necessary to assemble the head in the reverse order, passing the ends of the cord in two corresponding holes.

If there are doubts or it is not entirely clear how to charge a fishing line for a trimmer for a trimmer for grass recommend that you see how to correct the fishing line for a trimmer into a lawn mower. How to rent a coil C is the only right solution for mowing grass in a fishing line for a trimmer in. In this video, the instructor will open a trimmer head in detail by steps, it will measure the required amount of fishing line, as a rule, this is from two to four meters, and demonstrate the assembly and installation for a trimmer for the grass.

What is affected by the thickness of the cord?

Its effectiveness depends on the diameter of the fishing line when mowing different types of wild vegetation.

Today on the market you can find cords of such thickness:

1.6 mm. a fishing line for a trimmer for mowing young soft grass;
2 mm. the cord with this thickness is used mainly to mowing young wild vegetation and small weeds;
2.4 mm. this fishing line for a trimmer is designed to remove young weeds and mow large volumes of overripe wild vegetation;
2.7 mm. the cord of this type is used to effectively combat large weeds;
3 mm. a fishing line for a trimmer with this thickness effectively copes with the removal of small shrubs and thick old weeds;
3.3 mm. this cutting cord is suitable for removing the thin shoots of young wild trees;
4 mm. a large thickness of this fishing line allows it to cut large overflow weeds and thick shoots of wild trees.

It is important to remember that the greater the diameter of the cutting cord, the higher its noise during operation. In addition, thick fishing lines can only be installed on trimmers for grass with high engine power

For example, on electric trimmers for grass with fishing line and knife, you can put only mowing heads with a cord thickness of not more than 2 mm. Otherwise, the engine of the garden tool will quickly overheat.

How to refuel a fishing line for a trimmer in a coil of a trimmer for grass. the second method

The coils of the second type are dividing line. solid. On both sides are through the endless recesses, which are designed to wind a new fishing line.

To install the cord on such a head, the operator must act in the following order;

A previously prepared 6-meter piece of the cord must be bent exactly in half and cut. After that, the operator should get 2 identical pieces of fishing line;
Then at the end of each of the pieces you will need to make a small hook;
Next, the hook of one of the line for the trimmer for the grass will need to be inserted into the hole located in the upper head;
After that, you can start the winding of the cord. This is done strictly in the order indicates the arrow on the spray. The cord used should be evenly wrapped in the upper part of the coil. As a result, approximately 15 cm cord should remain free;
The remaining end of the fishing line will need to be fixed in the seizure of the upper part of the spool;
In the same way, you need to wind the second piece of the cord on the lower part of the mowing head of the trimmer for the grass.

This method is suitable for all types of cords, including a home.made fishing line from a plastic bottle.

Tips and recommendations how to wind a fishing line for a trimmer and what you need to know

There are several useful tips and recommendations that it will be useful to find out not only beginners, but also experienced masters-codes. These tips will help prevent negative consequences in the form of injuries and improper functioning of the mechanism. These recommendations say the following:

Set the lid to clicks. over, these are 2 or more clicks, which depends on the number of fixers. If one latch does not click, then when starting the tool, the drum can jump out and injure a person
Do not wrap a fishing line for a trimmer with its strong pulling, as well as in an amount more than you can insert it into place. It is better not to harvest the equipment than it will be more, as this will lead to negative consequences in the form of the impossibility of unwinding it if necessary
If you own the tool not with two conclusions of the fishing line, but with one (usually low.power units), then the winding process is performed in a similar sequence, as described above, only with the difference in the absence of the average side between the extreme bases of the coil
After replacing the material, it is necessary to first check the tools of the tool, and then proceed to the mocking of the grass. If you do not make a preliminary check, then the forests can be unwound, and injure a person

It is interesting! Choose the material of the appropriate quality so as not to get injuries when working with benzo.cards, trimmers and motorcycles. In the process of beating grass, small stones and other materials fall under the rotating parts, which can fly over long distances, therefore, despite the fact that the fishing line for a trimmer is not a knife, working with a tool should be carried out in protective special uniforms.

The result of the work done is as follows. after the replacement of the new material is enough for an area of up to 600 square meters, but when taking into account the presence of a reinforcing layer on the fishing line

Ordinary nylon materials serve less, which is important to take into account when working. Do not try to mow thick.button grass with fishing line, as there are special metal wheels or knives for this

Publications

How to remove and replace the coupling on a chainsaw. repair and adjustment

Features of the correct choice of chainsaws

The chainsaws are not started all the reasons and ways to eliminate malfunctions

OpenMower: Robot Hardware | YardForce Classic 500 Teardown, Mainboard Replacement, Firmware Install

How is a trimmer selected for grass for injection of grass, take into account all the criteria

Method 1. how to correct the fishing line for a trimmer or put it on a coil and choose the required length

To implement this method, you will need to pre.prepare a fishing line for a trimmer of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is a simple way to find out the required amount of fishing line, the refueling of which will be needed to charge the coil. To do this, the equipment should be wound inside the coil until it is equal to lateral protrusions. At the same time, the equipment should not go out for these extreme ledges.

The thicker the equipment used, the less its length will need and vice versa, the thinner, the longer the segment will need.

Instructions on how to properly tie the equipment into a tip of a trimmer for grass or motorcycles is the following look:

To begin with, a segment of the fishing line, which was prepared to install in a coil, must be folded in half. In this case, one edge should be more than the second by 10-15 cm
After that, the second end is taken from the other side, and doubles. Move to it so that the measured ledge 15 cm is preserved
There is a slot in the internal partition of the coil, into which the resulting loop should be brought. The slot in the wall is shown in the photo below
Next, find out the direction of the winding of the fishing line. If you wrap the equipment in the wrong way, then it will not function correctly, and you will need to redo the work. To insert a fishing line for a trimmer, and wind it in the right direction, you should examine the surface of the coil. It should indicate the direction of winding (in 99% of cases this direction is indicated). What does the direction indicator look like on the coil shown in the photo below
This indicator in the form of an arrow can also have a designation, as an example above “Wind Line”, which means the direction of winding. If the arrow indicator is absent on the coil, then you need to look at the head. There is a direction of its rotation on the head, and in order to correctly wind the fishing line for the trimmer, you should wind it on the drum in the opposite direction of the indicator of the arrow pointer. So, if the shooter is on the tip, then you need to wind in the indicated direction, and if it is not there, then you should wind against the direction of the arrow on the surface of the head
Having decided on the direction of rotation, you should proceed to the winding. Each end should be carried out in its groove. If there is no separator, then the equipment is necessary in the corresponding distribution order
When almost the entire fishing line for the trimmer is wound on the coil, you will need to perform the following-place a short part in the hole of the side wall of the tip, which should be up to 10-15 cm, and then similarly to do the procedure with another end, placing it in the holes from the parallel side
We insert the coil into the head, pre.letting the ends of the fishing line into the holes of the drum
We install the drum in place and, pulling the ends of the fishing line, remove them from the engagement with temporary clamps in the coil wall. After that, you can put on the lid until the latch is triggered
On this, the process, how to replace a fishing line for a trimmer on a trimmer, is completed, and if necessary, only the ends can be cut (if their length does not suit), and install the drum in the assembled form on the tool

With how to put the drum in place, no difficulties arise. There is a second way to charge mowing equipment into a motorcycle. How is it different, and how the second method of refueling the fishing line to the coil of motorcycles is carried out, we will find out in detail.

TE-600

Viking TE-600 is a device with high power and small mass. The tool is used for sections of small area.

The device copes with the design of the edge of the lawn, sprinkles grass near the walls of buildings and at home.

The device is equipped with a limiter of the length of the electrical wire, which prevents a sudden power outage. The operator can adjust the handle in height. If you install hinged blocks instead of the handle, then the tool can be used as garden scissors for cutting branches of trees and bushes. The engine is equipped with a system of protection against overload.

The engine has a power of 0.54 kW.
The width of the cutting zone 350 mm.
Noise level is 96 dB.
Table head of the TAP N GO brand.
Mass 4 kg.

The coil is automatically wound with the adjustment of the double thread of the trimmer head by means of pressure on the coil.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the fixing technological hole located inside the spool.
The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobbin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

disassemble, rogue, viking, lawn, mower, semi

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

We carry out the winding of the fishing line

Coil with one working osik

The easiest option and a simple sequence of actions:

The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the fixing technological hole located inside the spool.
The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobbin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

Is it possible to make a reel on a trimmer with your own hands

Such a homemade mowing nozzle is installed on a walnut shaft. Tightening or unscrewing the nut without fixing the shaft does not work. To replace the cord, it will be enough to unscrew the screws, insert a piece of fishing line of the desired length and press again.

You can also make a mowing nozzle to attach a fishing line for a metal sheet to it. How to do this, you can understand from the next video.

Repair ‘Electrics Gardena (change the coil)

The guaranteed exit of the factory trimmer for grass will inevitably require changes in the mowing fishing line. Having a very rude idea of how to introduce a fishing line for a trimmer into a trimmer coil for grass on their own, newcomers are reluctant to deal with this business. But, having certain abilities, the mastery of this simple science is not difficult, and similar instructions presented below will greatly facilitate such a process.

First of all, in order to wound a fishing line for a trimmer, you need to remove the coil (bobbin, spool) from a trimmer for grass; Certain actions will depend on the complexity of the configuration and the type of product itself:

Small electronic trimmers for grass with the working position of the motor and a coil below, you have side buttons on both sides of the bobbin. With simultaneous pressing, the upper part of the coil, together with the internal M, is turned off for winding the fishing line, although the lower.

The video is devoted to the problem of changing the spit line to trimmers for grass, it will be interesting for everyone who is dealing with similar devices. Before the audience, a person appears in work clothing, who promises immediately and at the same time to state the method of manipulation in detail, is necessary if you set the goal of changing or wiping a fishing line for a trimmer.

The hero attracts how important it is to first get a quality fishing line for a trimmer, then it will be reliable and will last a long time. Then a person indicates how to easily remove the old fishing line for a trimmer, then he shows the most that he already has

How to change, remove the head of the electronic trimmer head for the BlackDecker GL716 grass during repair, that is, change.

Change of vein on trimmer

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the prerequisites of this happen subsequent.

Option 1. it came out snacking, t.e. Squeezing the cord between the turns. This non.bond usually occurs if the user wound a fishing line for a trimmer to the coil unevenly, with a crossbreed of turns, or wound it with the missing tension. In the latter case, when the mowing head is rotated at huge revolutions under the influence of centrifugal force, the cord begins to drag on, under the influence of which you intervaling fishing. To eliminate the task, you will have to disassemble the coil on the trimmer and rewind the cord correctly, in other words, even coils with good tension.

Option 2.7. very short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head are insufficient (short). The centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to suspend the unit (drown out the engine as it is also called disconnecting an ethletric trimmer for grass from the network) and pull the fishing line for a trimmer manually, after pressing the button.

Option 3. A fishing line for a trimmer was soldered by a snot of a spitter head. This leads to the coil stops and does not even spin when the button is pressed. In the main thing, this happens for several reasons: the bad quality of the cord, overheating of the coil during prolonged operation of the unit, a string of fishing line on solid items.

At the beginning of the cord of the advantage of manufacturers, you will like more of low.quality and fusible materials that do not hold mechanical and temperature loads. Therefore, preference should be given to “branded” fishing.
If you still got a fishing line for a trimmer of an unknown property, and it is often soldered at one time of work, that is, an option to follow the example of certain users, which, after refueling the cord, moisten it or silicone grease (from a spray can), or mineral oil). This procedure greatly reduces the possibility of soldering a fishing line with each other.
Also, a fishing line for a trimmer can sleep if at one time the mowing she hit a hard object (stone, fence, dry branch, etc.D.). At the end of this, it is a little stretched and draws back into the head with a high speed. The cord is heated from friction, and its turns are stuck together. The only thing that is done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

A mowing string head is one of the types of executive mechanism of a garden trimmer for grass. It is intended for mowing grass and constructively represents a special coil (bobin) from which a cutting cord (string, fishing line for a trimmer) sticks out in different directions). The string is a consumable material that is subject to replacement during operation. Based on the constructive and operational features of the trimmer for grass, manufacturers equip their products with a wide variety of types of heads-from simple hand coils to complex automatic bones. The more difficult the device of this mechanism, the more likely its breakdown. What to do if the coil does not spin, the string is not served or broken, as well as with other malfunctions. in the material further.

Launcher of the starter and gearbox

The gearbox conveys the rotational moment from the engine shaft to the cutting tool, its gears during operation should be absolutely clean and necessarily lubricated with special lubricant.

In what cases are the repair of washing machines, which everyone should know about

DIY DIY DIY. drawings, diagrams, dimensions. 120 photos of homemade megaples

Conducting a technical inspection on their own once a season will get rid of the need to carry out the repair of the gearbox or its replacement, with the acquisition of an expensive new node.

The starter is necessary to bring a trimmer for grass to working condition, its diagnosis is to check the tension of the lace of the starter coil with the teeth of the coil, which are often destroyed at a sharp launch.

A non.working starter in a benzocos is not subject to repair, it must be replaced with a working unit, as part of a mandatory inspection or a set of repair measures.

Separate attention and care require cutting elements that must always be cleaned of dirt and mowed grass after operation. Regular inspection and thorough preparation of the device for work will help to avoid expensive and costly repair time, always be sure of the operation of the lawn mower.

Is it possible to make a coil for a trimmer for the grass with your own hands

On sale there are a large number of trimmer heads (not automatic), which have a low price and good quality. But sometimes situations arise, for example, in the country, when the trimmer coil broke, and its repair is impossible, the store is far away, and you need to mow. In this case, you can quickly, literally in a few minutes, make a simple trimmer nozzle to fix the fishing line from ordinary plywood 10-12 mm thick.

Take a piece of plywood or textolite and draw a circle with a diameter of about 14 cm on it.
Cut the disk with a jigsaw or hacksaw for metal.
Drill a hole in the center of the disk, suitable in diameter to the gear shaft. Do not forget before installing a disk on the shaft, put a puck on it.
You can fasten small corners along the edges of the disk or make 1-2 holes on the opposite sides. They will serve for refueling fishing lines in them.
To fix the fishing line for a trimmer, you can screw several screws into the plywood.

Such a homemade mowing nozzle is fixed on the shaft with a nut. Twist or unscrew the nut without fixing the shaft will not work. To replace the cord, it will be enough to release the screws, insert a segment of the fishing line of the required length and press it again.

Also, a mowing nozzle for fixing the fishing line on it can be made from a metal sheet. How to do this can be understood from the next video.

The device of the gasoline trimmer engine for grass. Gasoline trimmer device for grass

Numerous models of manual motorcycles that are available on the market today differ in power (and, as a result, in their capabilities), weight, the presence of certain additional functions that increase the ease of use, but the fundamental scheme of the instrument device remains unchanged.

As a power drive in any gasoline trimmer, an internal combustion engine is used. By means of a hard or flexible shaft, rotation from it is transmitted to a cutting element. a coil with a cord (fishing line) or a special knife. The shaft is placed inside the metal rod, on one end of which the engine and the fuel tank are fixed, on the other there is a cutting head. In the middle part of the rod, the handle is attached. Most often, it is precisely on it that keys, buttons and switches are placed, with which the work of the trimmer for grass is controlled.

The layout of the control elements can differ slightly depending on the model of the tool, but, as a rule, this includes a button for jamming the engine, the gas key, which allows you to control the throttle darling of the carburetor, and the stopper of this key in the pressed state, facilitating control with large volume of work.

Gearbox. 2. Trimmer head. 3. Protective casing. four. Gas Stop button. 5. Switch.

Gas lever. 7. Lever. eight. Stop a gas lever. 9. Barbell. ten. Loop for fastening belt carbine.

Air filter. 12. Spark plug. 13. Engine case. fourteen. An exhaust manifold. fifteen. Gas tank. 16. Starter.

The device of the trimmer rod for electric grass. Design features

It should be noted. that the cutting head for a trimmer for grass contains special arrows. They allow you to perform rotational coil movements in different directions. The electric trimmer is an electric with a rod, a good electric trimmer for grass will last. If there is a need to wind the fishing line for the trimmer towards rotation of the shaft, it turns into a specific position. A large number of wound cord threaten equipment breakdown. Two arrows are contained only on imported models. Now the heads are presented on the market with one arrow.

If the cord is not wound after the semi.automatic head, then its previous winding is incorrect. That is, after the head for a trimmer for the grass was installed, the user did not pull the ends of the fishing line from the grooves. Another unpleasant moment in the beard of grass may be sintering the coil turns.

Why is it happening? This happens when there is a cord with a solid subject. At the same time, it brakes sharply and, with the subsequent movement, the fishing line for the trimmer begins to go inside the device. Thus, it gets on the rogue and sticks together. Because of this, the employee has to take a break and correct the situation. However, this can be avoided. Before installing the coil, it is necessary to treat the fishing line for the trimmer with a special silicone substance.

For various models of trimmers, a semi.automatic head is used, consisting of two parts. a case and a spray. Both elements contain springs. The second part can be performed in several versions:

single.section. both parts of the fishing line are wound together;
two.section. each end is wound on a certain part; This type is the most effective, since the fishing line for the trimmer is not confused and does not sinter.

There is a simple and cheap way to turn a single.sectioned spool into a two.section. For this you need a strong plate. From it you need to cut a circle, the diameter of which should be equal to the thickness of the buffet. In this case, the thickness is taken near the place where the fishing line for the trimmer is wound. This circle moves freely. Next, a cut is made on the ring, put on a spool and is connected using glue or tape.

As a result, you can wind a fishing line for a trimmer to the required section. The head for a trimmer for a universal grass can have from two to four holes that are located opposite each other. Mowing ends come out of them. In addition to the presented coils, there are heads where a certain size of the fishing line is inserted. In this case, the number of mustos increases to twelve. Many users believe that such a device is quite convenient. However, not all people adhere to this opinion.They believe that in this situation the fishing line will have to spend more. In addition, to replace it, it is necessary to stop the workflow. Electric trimmer for grass. Electric trimmer for grass consists of an electric motor, handle. The head for a trimmer for grass, the caliber of which can be varied, is suitable for haircuts of grass, shrubs and trees. Before buying a trimmer for grass. it is necessary to study the area, as well as the features of the equipment. So, we found out why the head for the trimmer for the grass is universal and how to correct it correctly.

Trimmer for Viking TE 1000. Description of the model

Amateur trimmer for Viking grass is used for edging and haircuts of decorative lawns, flower beds and pedestrian paths. The garden tool is equipped with an ergonomic handle, the position of which can be adjusted in line with the growth of the operator. To send the cutting organs, the model is equipped with a gourmet mechanism. This decision makes it possible to protect the bark of trees and stalks of flowers from random damage.

The Viking 1000 trimmer is equipped with a powerful engine, the speed of which can be adjusted using an electronic system. The engine is equipped with effective protection against overload, which prevents unforeseen breakdown of the motor during intensive operation in hot weather.

The technical characteristics of this amateur tool include:

The power of the factory engine is 1 kW;
grass cut width. 35 cm;
The maximum speed of rotation of the cord/cutting knife is 8000 rpm;
The permissible diameter of the fishing line used for mowing is 2 mm.

The internal elements of the electric ships are reliably protected by the reinforced plastic case, which can be disassembled using the key from the kit.

Sources:

https://1-tools.ru/rezka/VIKING-te-600-zamena-leski.html
https://labequip.ru/kak-zapravit-lesku-v-trimmer-VIKING/
https://101benzopila.ru/kak-razobrat-poluavtomaticeskuu-katusku-ot-trimmera/
https://benzo-electro-instrument.ru/kak-snat-golovku-trimmera-VIKING-te-600/
https://labequip.ru/kak-snat-golovku-trimmera-VIKING-te-600/
https://101benzopila.ru/kak-snat-golovku-trimmera-VIKING-te-600/
https://gc-ug.ru/selhoztehnika/kak-razobrat-trimmer.html
https://spec-avtoteh.ru/selskoe-hozyajstvo/VIKING-te-600-zamena-leski.html
https://gc-ug.ru/selhoztehnika/VIKING-te-600-zamena-leski.html

Lawn Mowers disassemble, lawn, mower, rogue, semi, viking