How to fit the line into the trimmer spool

Second winding method

  • A previously prepared segment of six meters in length is required to be bent exactly in the middle and cut. Thus, two segments of the same length are obtained.
  • At one end of each segment, you need to make a small “hook”. To do this, it is necessary to bend a couple of centimeters from the edge and fix it for a short time so that the “hook” does not unbend.
  • Then one segment is taken. The hook is inserted into the through hole at the top of the bobbin.
  • Now you can proceed to the key stage. winding. The direction in which to wind is indicated by an arrow on the bobbin. It is important to ensure that the line is wound strictly within the upper part of the reel. You do not need to wind the thread to the very tip. about fifteen centimeters should remain free from the end.
  • In the upper edge of the spool there are small recesses (so-called grooves) for fixing the consumable. The loose “tail” of the thread must be inserted into one of these grooves.
  • The top of the coil is tucked in. Now you need to do the same procedure with the bottom. Take the second piece of thread. The “hook” is threaded through the through hole at the bottom of the bobbin.
  • After that, you can start winding the fishing line (within the lower compartment). And for this segment, you also need to leave about fifteen centimeters free from the end. This remaining “tail” must be inserted into the notch opposite to the one into which the end of the first segment was inserted.

The subsequent steps for this type of coils are exactly the same as described for the previous type in paragraphs five to nine.

This is how the line in the trimmer spool changes. There is nothing complicated in the process. And already after several refuelings, all actions will come to automatism.

How to replace string trimmer edger line

To visually study the process described above, you can turn to the Internet for help. On the popular YouTube portal there are many different videos showing how to wind the line on the trimmer reel.

How to wind the line onto the Patriot trimmer reel?

Almost every beginner when using a trimmer is faced with the problem of changing the line. While it is very easy to change your line, you need to learn how to do it correctly. Changing the fishing line with proper skill will take no more than five minutes. you just have to constantly practice it. This article will look at changing line using Patriot trimmers as an example.

Features of the use of trimmers

A trimmer that mows grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, flower beds and flower beds, row spacing in a garden plot.

Such a convenient, and most importantly, effective device, like a trimmer, exists in several variations:

As the names suggest, trimmer types differ markedly from one another. But regardless of the type of this tool, a fishing line can be its cutting element. Of course, the line tucked into the trimmer reel is not endless. And sooner or later you will need to replace it with a new one.

Line consumption directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the trimmer, the more active the line is used in it. And, accordingly, the faster it will end. In this regard, the question arises: how to thread the line into the trimmer spool?

Not everyone knows the answer to this question. But the winding of the line on the reel plays an important role in the trimmer operation. For the device to function properly, it is very important to properly wind the new line onto the reel. How to change the line on the trimmer, and will be discussed in this article.

Thickness selection

In addition, you should pay special attention to the thickness of the consumable. For mowing young grass, a thread with a diameter of one and a half millimeters is suitable. The larger the diameter of the thread, the more dry and coarse weeds it is capable of overpowering.

When choosing a fishing line by thickness, there is one “but”. It is important not only to assess the capabilities of the material, but also to take into account the features of the trimmer. Be sure to check the user manual that came with your tool for information on cutting element requirements.

Using the wrong thread can damage the tool. Using a thread that is too thick will overload the machine’s motor. And the use of a thread that is too thin will significantly increase the wear of the twisting mechanism.

That is why it is necessary to approach the choice of consumables no less responsibly than to refuel it in the trimmer. When a suitable fishing line is found and purchased, you can begin to consider ways of winding it on a reel.

Line winding

Threading the line into the trimmer spool is a relatively simple procedure, provided you follow a specific procedure. When you need to determine how many meters of consumable is enough, wind it around the bobbin so that the skein does not exceed the diameter of the sides. Having decided on the length of the cord, follow the instructions below:

  • Fold the consumable in half so that one end of the line is 10-15 cm longer than the other.
  • Charging should be started from the center board, which divides the trimmer bobbin into 2 parts. Find the groove where the cord should be inserted. Bend the last in half.
  • Determine in which direction you want to wind the line. To do this, take a closer look at the bobbin, which may contain an arrow or an inscription. She indicates the side of the winding. If there are no markings on the reel, then look at the arrow on the mowing head. wind in the opposite direction.
  • The consumables should be washed carefully, turn to turn. Try to stick to the maximum thread tension.
  • After completing the lining, secure the short end of the material first. To do this, insert it into a groove on the side of the coil that fits in diameter. The other end (longer), attach in the groove on the other side of the trimmer bobbin.
  • After securing the fishing line, cut off the ends. Do not forget to leave allowances of about 10 cm.
  • Place the loaded bobbin onto the mowing head of the device. To do this, you need to alternately insert and pull the thread into the outlet holes of the head, in order to then place the bobbin of the device into the skin.
  • Using the required force, pull the cord out of the locking grooves and tighten the material. After completing this step, put on the cover and secure it with the latches.

Step-by-step winding of the line to the spool

You can also wind the cord on the trimmer in another way, in which two pieces of material are charged instead of one. The replacement is done like this:

  • Bend one end of the cord into a crochet hook.
  • There should be a hole at the bottom of the bobbin to hold the line in place. Insert the bent end of the thread there.
  • Wind the cord material in the direction of the arrow to the desired level, which does not exceed the diameter of the trimmer spool.
  • Do the same for the second bobbin compartment.
  • The assembly of the device head is similar to the first method.
READ  Reel For Trimmer Without Winding Fishing Line

Line selection

For the threading of the line into the trimmer head to be successful, it is important not to miscalculate with the choice of consumables. The thicker the cord you tuck in, the thicker and tougher the grass it will be able to cut. Often a universal line is used, the diameter of which is 2 mm. You can choose a diameter suitable for the mower in the following ways:

  • Refer to the instructions that came with the trimmer for line thickness information.
  • Pay attention to the bobbin itself. Sometimes information about the possible diameters of the fishing line is applied on it.
  • Another option is to try inserting the cord into the exit hole. If it easily goes through it, then the selected line diameter is suitable for use.

Trimmer reel

You can choose a cord thread according to the type of engine. If the line is too thick, then the resistance to rotation will increase. in this case, the engine will overheat and will soon fail. Helpful hints:

  • For an electrical device with a motor less than 500 V, a 1.3 mm thread is suitable. If you can’t find one, then you can use a 1.6 mm line. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
  • With a petrol trimmer, the shaft mower matters. For the folded version, a 2 mm cord is often used. If the shaft is straight, use a 2.4-2.5 or 3mm thread. The thickest line is installed on powerful devices. from 1.3 kW.

Pay attention to the type of section of the cord thread. Some popular options:

  • The most common round lines. They mow fresh grasses well, but they cope worse with shrubs, dead wood.
  • Twisted (spiral) cord is not very strong, but is good for thin young grass.
  • Serrated thread with sharp edges is ideal for large weeds in a neglected area.
  • You can mow your lawn more evenly with rectangular, star or square trimmer lines, but they are not very strong.
  • Strongest. two-piece inner-core round cord.

Types of trimmer line

Please note that you cannot use wire, metal strings and cables, as well as ordinary fishing thread instead of fishing line. The device will be dangerous to both the user and others. So the cable or similar products will gradually begin to work, as a result, their ends will unravel, and small pieces will scatter at high speed.

Instructions

In order to change the line, you need to remove the old one (if it was).

The reel is the part of the trimmer structure that is located inside the mower head, drum or bobbin. Heads may vary depending on the manufacturer. But this article only covers Patriot, although their mechanism is used by many other companies.

Now you need to understand how to properly remove the head from the trimmer and how to pull the drum out of it.

Instructions on how to unscrew the manual head on the trimmer are described below.

  • First of all, you need to clean the head from dirt and adhering grass, if it is dirty. To do this, lift the mower head up and, grasping the casing, remove the special protective cover on the drum.
  • The next step is to remove the spool from the drum. The reel can be easily removed even with one hand, because it is not fixed in any way inside the drum.
  • The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with the spool, while unscrewing the screw counterclockwise.
  • Now you can pull the coil out. As mentioned above, it is not secured by anything, except for a hook with a metal shaft, so it does not need to be pulled out with force. Carefully, in a circular motion, pull the spool out of the drum.
  • Now it remains to remove the old fishing line and follow the following instructions.

Installation of the spool and drum in their original place is performed according to the reverse algorithm.

Before threading the line, make sure you have purchased the correct thread for the trimmer. In the event that the thread is not suitable, the consumption of fuel or energy increases, as well as the load on the engine of the lawn mowers.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m of line. The specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the spool itself. If you cannot accurately determine the length, you can do the following: insert and wind the thread until the coil is fully charged (the line level will be compared with the protrusions on the sides of the coil). It is necessary to ensure that the line sits evenly in the reel.

Do not forget that thick thread will be shorter than thin thread.

The instructions for threading the line into the spool are described below.

  • The prepared thread must be taken and folded in half. It should be ensured that one edge is 0.1-0.15 m longer than the other.
  • Now you need to take the ends in different hands. The one that is smaller must be pulled up to the larger one so that it becomes 2 times shorter. When bending, maintain an offset of 0.15m.
  • Find the notch inside the coil baffle. Carefully pass the loop you made earlier into this slot.
  • To continue working, it is necessary to determine the direction of winding of the thread in the bobbin. To do this, it is enough to inspect the coil. there should be an arrow on it.
  • If the arrow-pointer could not be found, then it is quite possible that there is a written designation. An example is shown in the photo below. It is necessary to inspect the coil head. There is a direction indicator on it. However, this is the direction of travel of the coil. To get the winding direction, you need to wind in the opposite direction.
  • Now you need to load the spool with line. It is worth noting that there are special guide grooves inside the coil. Follow these grooves when winding the thread, otherwise the trimmer may be damaged. At this stage, you need to charge the coil very carefully.
  • When the user winds almost the entire thread, take the short end (do not forget about the 0.15m protrusion) and pull it into the hole located in the wall of the reel. Now you need to repeat this action in the same way with the other end (on the other side).
  • Place the reel itself in the head of the reel, before that threading the line through the holes inside the drum.
  • Now is the time to put the drum back in place. After that, you need to take the ends of the line with both hands and pull them to the sides. Then you need to put the lid back on (here you can safely make efforts until you hear a characteristic click).
  • Remained to do the “cosmetic work”. We need to see if the thread is too long. You can start the trimmer and check in practice if everything is comfortable. If the thread comes out a little long, you can cut it with scissors.

How to properly wind the line on the trimmer spool?

Despite the fact that gardening equipment has been used for quite some time, it is still a novelty for some owners of private houses. That is why there are often questions about how to properly wind the line on an electric or gasoline trimmer.

This is essentially a simple operation, but all its stages must be performed correctly in order to achieve the desired result. over, in the operating instructions, only a few manufacturers provide an answer to this painful question. Explore the article and find out how the line winds on the trimmer reel.

The procedure for winding the line on the trimmer spool

First of all, you should know that trimmers have different working attachments. The reel can be designed for different lengths and thicknesses of the line. this point should be taken into account when purchasing consumables.

READ  How to Repair a Starter on a Trimmer

So how do you load the line into the trimmer reel? All work is divided into several stages:

  • First you need to disassemble the trimmer head.
  • Unscrew the nozzle by rotating the drum to the right.
  • Press with your fingers on the two latches located on different sides of the entrance, and remove the top cover of the nozzle. You can pry off the cover with a screwdriver. This should be done carefully: reels with automatic line feed have a spring that can forcefully throw the cover along with all the contents of the reel.
  • Remove scraps of old fishing line.
  • Now you need to find the middle of the line. To do this, unwind it to the required length (for example, 10 m), cut and fold it in half.
  • Hook the middle of the line into the existing groove or insert it into the hole specially designed for this. And start winding. The direction is indicated by an arrow, which is usually marked on the trimmer reel body (usually against the rotation of the drum). Some models have a double-sided spool: in this case, the line should be wound in different directions: one end in one direction, the other in the other, while the loop of the line must be inserted into the dividing slot located in the middle.
  • Leave loose ends of the line about 20cm each. Later they will need to be fixed in the recesses.
  • And finally, the last step will be the assembly of the drum. Reinstall the washers and spring. On the top ring of the reel there are two notches where you need to tuck the antennae of the fishing line. Thread them through the holes and place the spool in the drum, trying to tighten the line without displacing the spring.
  • Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

When you turn on the trimmer, the excess line will be cut off by the trimmer blade.

As you can see, winding the line on the trimmer reel is not difficult: the main thing is to do everything right. And here are some more tips that will come in handy when choosing a fishing line, winding it and subsequent work:

How To Tips for Easy Restring of Weed Eater with 2 strings

  • fishing line comes in different thicknesses and with different sections. The best option for winding is the “native” line for this model;
  • never use fishing line or metal cables for the trimmer. Such a substitution may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure not only the lawnmower himself, but also those around him;
  • the line is cut when the trimmer is in contact with hard objects. Try not to allow this, otherwise you will have to stop each time, turn off the device and rewind the line on the reel;
  • Use regular line for cutting lawn grass and pigtail line for coarse weeds. It is more durable and will not constantly cut.

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these garden tools, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Single-barbed trimmer spool

Single-barb lawn mowers reel

Many owners and specialists note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the trimmer reel.

After winding, you need to leave a free end of 15-30 cm to increase the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.

Trimmer head with two antennae

Head with two flutes

After removing the spool from the spool body, we determine the number of strands for winding the fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interlacing adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off the excess.

Winding the line to the trimmer

Measured and accurate dismantling of the spool from the spit coil makes it possible to go directly to the winding of the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

  • Trimmer head with one working mustache;
  • A bobbin with two line antennae;
  • Auto winding reel.

How to wind the line onto the trimmer spool

  • First, the head must be disassembled, for this we press with our fingers on two latches, which are located on the body of the head at 90 degrees from the entrance, and remove the top cover.
  • After you remove the top cover, you need to get the cord holder, while being careful not to lose the spring, as well as the tap holes through which the line is fed. Measure out the correct amount of line and fold it in half.
  • Place the folded line in the middle over the holder (there is a special slot in it) and start winding the cord so that each mustache of the two falls into its own compartment of the holder.
  • Leave a free length of the mustache about 15 cm, fix them in the special slots of the holder and install it in the lower part of the head.
  • Pull the mustache out through the eyes and install the top head cover, aligning the side latches.
  • As a result, you got the head correctly seated with the fishing line, you can continue to work.

And finally, a video on how to quickly thread the line into the trimmer head.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find a fixing hole for the line on the inside of the reel, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. Having reeled the fishing line, we leave a small piece of it unwound in order to expose it outside. We fix this piece in a special groove located on the inner part of the reel and designed so that the line does not unwind at the time of collecting the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and thread the outer piece of fishing line into the existing hole, assemble and put the coil back on the trimmer.

line, trimmer, spool

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both tendrils are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. A reel with one groove should have a through hole through which the line is threaded. We unwind 2-4 m of fishing line, thread it through this hole so that it sticks out equally on each side of the fishing line. And we simultaneously wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, fix the resulting ends in special grooves, and if they are not there, we hold them with our fingers. We pass both ends into the existing holes on the outer casing of the coil. We collect the coil and attach it to the trimmer.

READ  Replacing Fishing Line In Patriot Trimmer

If there are two grooves, fold a piece of fishing line 2-4 m long in half, insert the loop obtained at the place of the bend into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option.

There are also reels in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, without winding, are threaded completely through the holes on the outer body of the reel, collect the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Rotate the button. the fishing line itself is wound inside. At the same time, it will not work to turn it in the “wrong” direction, since it can only rotate in one direction. If you get used to it, you can wind fishing line on such a reel without even disassembling it. you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

That’s all on this issue. Happy winding!

How to wind the line onto the Patriot trimmer reel?

Almost every beginner when using a trimmer is faced with the problem of changing the line. While it is very easy to change your line, you need to learn how to do it correctly. Changing the fishing line with proper skill will take no more than five minutes. you just have to constantly practice it. This article will look at changing line using Patriot trimmers as an example.

than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

How to properly lay the line on the trimmer spool

How to wind line on a trimmer: examples and recommendations

As a rule, before going fishing, it is necessary to check all the tackle, the reliability of the connecting loops and the sharpness of the hooks. But do not forget about the backing, which is wound on a reel, because the success of fishing in general will depend on how you wind the line around the trimmer. Improperly wound, it can lead to a beard. which is quite difficult to untangle and which takes up a huge amount of precious time, the casting distance can be significantly reduced, and in general in such a situation it is better not to fish.

How to properly attach the thread to the trimmer

Winding the line to the trimmer. it’s a simple matter, but it requires some skill. First you need to firmly attach the reel to the rod. Then pass one end of the fluorocarbon through all the ears of the rod and fasten it to the spool. To do this, you need to raise the bow of the coil, wrap the fishing line around and tie with an Arbor knot.

If the thread is stiff or thick, then before winding it should be immersed in warm water, after this procedure it will become more elastic and lie smoother. When winding, it is desirable that there is an assistant who would hold the bobbin with the fishing line. In the process, you should slightly slow down the fluorocarbon with your finger or a soft cloth.

What should be the length of the working thread

It all depends on the method of fishing and the reservoir. If a small length of line is required for fishing, then it should be less; if a long cast is required, then more fluorocarbon is needed. For a quick change in the field, every angler should know how to change the line on the trimmer. If the spool of the reel is deep, then approximately two-thirds must be filled with a cheaper thread, and the remaining part should be wound with working fluorocarbon, which is necessary directly for fishing. The reel should consist of a thinner line than the working line, this will increase the density and not fall through the main.

Coil selection

Beginning fishermen, due to their inexperience, pay little attention to the choice of a rod and tackle, but the right equipment is the key to the success of fishing. Usually, spools are purchased with a spool size from 2000 to 3000, which can accommodate 100 meters of line with a number from 0.2 to 0.3 mm.

In addition to their size, they differ from each other in the way they are wound on a bobbin. You can wind the line on the trimmer spool with straight, cylindrical or tapered laying, it all depends on the model. It is also worth paying attention to the country of origin of fishing tackle. If the reel is of Chinese origin, from a cheap series, then always be prepared for line tangling during casts and the appearance of a beard. in addition, the cheap option fails quickly enough and requires repair or replacement.

With high-quality winding, fluorocarbon should form a strictly parallel stacking relative to the spool with a direct winding method, and inclined with a tapered.

Storing nylon thread on a spool

How to wind the line on the trimmer. sorted it out, now let’s talk about storing fishing tackle, in particular fluorocarbon on the spool. For a long service life of the thread, you should adhere to several rules, the implementation of which allows you to save money on the purchase of new equipment.

It is important to remember that after fishing, the line and parts of the reel get wet, they should be well dried. Poorly dried fluorocarbon melts very quickly and becomes unusable. It becomes brittle and can break at the most crucial moment. To prevent this from happening, after seasonal fishing, the line from the reel should be rolled up and spread on the floor so that it dries well. This procedure should be carried out with backing (reeling). You can dry the nylon thread after each fishing trip if you go to it once a month.

You already know how to change the line on the trimmer, it shouldn’t be too difficult. Always store your fishing tackle in a dry place, this will guarantee reliability and durability.

How to wind line on a trimmer

During winding, the handle of the reel should be turned smoothly, without jerks and at high speeds. Care must be taken to ensure that the thread lies in straight parallel lines. Do not wind too thick line that is not intended for this reel.

Smoothly winding fluorocarbon, you should pay attention to how much is left to the side. The optimal distance is 2 mm from the top layer to the edge of the side.