How to get a fishing line for a trim in a reelled lawn mower. Varieties

Coils (heads) for trimmers

Kosyl heads with fishing fishing lines placed in them, along with knives and disks, are included in the list of cutting headset for trimmers. The main function of the heads, or, as they are often called coils, lies in the quick and neat mowing of the grass. Different types of heads are found on sale today. All of them are divided among themselves, mainly on the principle of feeding and charging fishing. This classification makes it possible to choose the optimal mowing head to almost any novice gardener.

Most amateur and household motorcycles stand out by a simple device. They consist of an engine, a bar in which a flexible or hard drive shaft, a handle and a cutting organ is located, the role of which often plays the head of a trimmer for grass. On the principle of feeding fishing line, the heads are divided into the following types:

• manual-a headset of this type got its name due to the fact that the cutting cord in it is served manually. Each time, if necessary, lengthen the fishing line for the trimmer, the operator must stop working with the trimmer and pull it out mechanically. This brings its inconvenience, but it is this type of device that is considered the most popular among gardeners. Hand coils differ from analogues of durability and low prices;
• semi.automatic. when working with heads of this type, you can lengthen the cord by pressing the headset to the ground. During this, pressing the button that drives the anchor mechanism occurs. He creates a centrifugal force that pushes the cord outward. The semi.automatic head for a trimmer for grass has one important advantage. when operating it, it is not required to stop working with a motorcycle, since you can lengthen a fishing line for a trimmer with a running engine. The only drawback is that the semi.automatic cutting headset costs a little more than hand coils;

• automatic. regular devices of this type are convenient in operation. To lengthen the cord to the operator, it is enough to slow down the engine speed motorcycles. Automatic factory coil for a trimmer for grass differs from analogues with ease of operation. However, the for a headset of this type are the highest in the market.

Each of the listed types of cutting devices is suitable for operation in certain conditions. Hand heads are best used in areas with solid obstacles. The low cost of a headset of this type will make it possible to buy several manual heads at once, and alternately change them as it fails. Automatic models, on the contrary, are quite expensive, so it is best to use them to care for clean areas.

Types of semi.automatic heads

Semiautomatic.type mowing head. As a rule, it consists of a case, inside which several springs and a spool are located. Shpuli, in their execution, are divided into:

Many owners of household trimmers remake single.sectioned spills for two.section. To do this, you need to find a strong metal plate, and apply a circuit with a spool diameter on it. After that, the plate is cut along the contour so that the thickness is located near the cord winding area. As a result, the resulting circle must move freely around its axis. Further on the resulting ring you will need to make a cut and put the spool inside the ring. Both parts must be interconnected using a tape or fast.drying glue. As a result, the manufacturer gets a spool, a fishing line for a trimmer in which can be wrapped in two sections.

Reviews about trimmer for grass gasoline hopper farmer-052

Advantages: powerful, comfortable in hand, not heavy.

Disadvantages: the quality is terrible. During the year of operation, the piston was changed twice, four times the starter. Constant problems with carburetor. In short, they repaired more than worked.

Comment: I will not advise anyone hoper. Before that, Interskol was (and stayed). worked and works at all without problems. We decided to take something ramps and really regretted it.

Advantages: Power of the biceps belt pissing rod

Comment: The device is just a beast. Power is enough for everything. When the trigger presses you immediately feel how powerful it is. At the first acquaintance with Khopom, they said that everything is crumbling. Will start several times and then from the thirtieth. And so on. As a result, he examined everything well, did not listen to anyone and took a chainsaw from Hopra. After two.year use, definitely a hoper if the technique is suitable for needs. And buying a trimmer for grass generally pleased. There were many devices in their hands from different manufacturers. So I can recommend confidently. P. S. Just remember that you take a gasoline tool, not a kettle. Here is not only the button on.-Off., but also proper maintenance. The correct first launch, running.in, lubrication, cleaning, etc. D. All successful purchases!

Disadvantages: Assembly is bad. Half of the bolts are not swept. Fuel tank separate topic. For a year of use, changed three times. First time under warranty, then I bought separately. All three times the tank burst in the same place. The quality of the plastic tank is disgusting. The tank is suspended by only two bolts and brackets. protection of the tank is a plastic corner. After the first replacement, the tank bought enhanced metal protection, but she also did not help. The fuel tank bursts from the vibration of the braid for grass at the mounting site to the engine body.

Comment: This braid for grass was repaired more than worked. I don’t advise buying this braid.

Advantages:.comfortable (biceps belt).Powerful (grass to waist. In dust)

Flaws:. The resource of motorcycles is only 150 (like Huskvarny 600-). If something opens, I will complement.

-They scared that high grass to the waist would not be reimbursed by a trimmer, because everyone has everything wound up on a gearbox. Nonsense, any grass, any burdocks in dust and dust waves. _.Scared that he eats a lot, all the same 3 liters.With. Nonsense, tank here 2l. And for 3 tsenzil, all that was needed (half of the football field), and the grass was really in Posyas. Husqvarna’s neighbor 2 l.With. Eats the same. Scared that cheap and fall apart, everything will bounce. No, everything is tightly screwed and in general, I constantly beat her for bricks and wound the sticks and benches on it)). Nothing fell off. A crack appeared on the coil after I wrapped some kind of metal cable in the grass as a gearbox. But the crack is not significant, then it never went. Friends have been mowing such a mower for a year. Everything is good for them.

https: // jusof.COM/Katushka-dlja-Trimmera-PA6-30gf-Kak-Razobrat/https: // Poryadok.ru/catalog/katushki_leski_dlya_trimmera/https: // otziv-otziv.ru/Katalog/Trimmery/Hopeer/Trimmer-Benzinovy-Hoper-Fermer-052.HTML

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

• The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
• One end of the fishing line is inserted into the fixing technological hole located inside the spool.
• The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
• A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
• The left end of the fishing line is passed through the hole of the outer part of the bobbin.
• Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

How to wind a fishing line for a trimmer to a trimmer coil for grass

The refueling of the fishing line in the coil of the tool, at first glance, is not easy. But to carefully study this process carefully-and in the future all the necessary actions will be carried out without any difficulties.

To find out how to refuel a fishing line for a trimmer trimmer for grass, you should read this guide. The step.by.step instruction below takes into account the features of the coils of different types of trimmers, therefore it applies to any tool.

• The reel with a fishing line is the lower edge of the trimmer for the grass. First, of course, it is necessary to remove this head from the device. To do this, fix the rod (or, in other words, the shaft) on which the coil is attached. Fix it in such a way that it does not scroll at. This is the easiest to do this by placing a peculiar stupor between the thread of the shaft through a special hole (best metallic). When the shaft is fixed, you can unscrew the coil.
• At this stage, it will be necessary to extract a bobbin from the head, on which a fishing line for a trimmer is attached. To do this, you need to disassemble the head to the elements. To do this, you must first find a fixer on its case. It is located on the circumference of the product and is the likeness of the buttons. When the lock is found, you need to press it with an effort. Holding the latch pressed, you need to turn the head cover clockwise. Then you need to remove the lid and remove the bobbin.
• A tight spring is placed between the bobbin and the head. It must be set aside for a while so that it does not interfere with the winding process. Before proceeding to the winding of the fishing line, it is necessary to inspect the bobbin. If it has the remains of an old fishing line, they must be removed. When the bobbin is cleaned, you can start preparing a new skein.
• From a pre.prepared skein of a new fishing line, it is necessary to measure and cut off six (maximum. seven) meters. Spulk should be at hand.

At this moment, the key stage actually begins, which is devoted to this article.

The first method of winding fishing

The required amount of fishing line is cut off. Now you need to carefully examine the bobbin to understand what type it belongs to. It depends on this how to wind the fishing line for the trimmer.

Spulks are of two types. In general, they are slightly different from each other. Regardless of the species, the coil is divided into two compartments. the upper and lower. In the first type, the dividing line does not close into the ring and has a deepening.

The second type is solid, but near it on the sides on both sides there are small through holes. The method of winding the thread must be studied depending on which of the above species the coil belongs.

• The previously prepared six.meter segment must be bent in half. Best not exactly in the middle, but so that one half turned out to be about fifteen centimeters longer.
• Then the bending place must be inserted into the recess in the dividing line. One half of the fishing line should be in the upper part of the coil, the other half in the lower part.
• Now you can proceed directly to the winding. You need to wind up in the direction in which the arrow on the bobbin indicates. When winding, you need to keep the threads so that they are not intertwined and the upper half is wound into the upper part of the coil, and the lower half into the lower part. Each half should remain free about fifteen centimeters from the end.
• There are small recesses (or, in other words, grooves) in the upper edge of the bobbin to fix the consumable. The ends of the threads need to be inserted into these recesses so that they are fixed one opposite the other.
• The final stage of refueling the consumable in the tool. the ends fixed on the bobbin must be put into the corresponding holes in the head of the trimmer for grass.
• That’s all. The winding process is completed. Now it remains only to collect the head into a single whole. The spring is neatly placed back between the bobbin and the head. Then you need to insert the bobbin into the head and press them to each other.
• Free ends of threads are recommended to pull out more tightly. To do this, take turns pulling the ends of the consumables so as to extract them from the grooves of the bobbin. You can make sure that the cutting element is extracted from the holding grooves, having tried to pull the threads a little. they must freely go through the holes in the head.
• Clutching a bobbin downward, you need to put on a lid over it. The lid must be screwed to the head so that all the grooves on their buildings are compatible and the bobbin remains between them.
• And finally, the very last action. the head is screwed back to its place in the lower part of the tool.

The process is completed. Trimmer fishing line is tucked up. Trimmer for grass is ready for further work.

The second method of winding

• The previously prepared segment is six meters long, you need to bend exactly in the middle and cut. Thus, two segments of the same length are obtained.
• At one end of each segment, you need to make a small “hook”. To do this, bend a couple of centimeters from the edge and briefly fix it so that the “hook” does not extend.
• Then one segment is taken. The “hook” is inserted into the through hole in the upper part of the bobbin.
• Now you can start the key stage. winding. The direction in which you need to wind up indicates the arrow on the bobbin. It is important to ensure that the fishing line for the trimmer is wound strictly within the upper part of the coil. It is not necessary to wind the thread to the tip. from the end should remain free about fifteen centimeters.
• There are small recesses (the so.called grooves) in the upper edge of the coil to fix the consumable. Free “tail” of the thread must be inserted into one of these recesses.
• The upper part of the coil is filled. Now you need to do the same procedure with the lower part. The second section of the thread is taken. “Hook” is spreading into the through hole in the lower part of the bobbin.
• After that, you can start wrapping a fishing line for a trimmer (within the lower compartment). And this segment also needs to be left with free ones about fifteen centimeters from the end. This remaining “tail” must be inserted into a recess opposite to the one in which the end of the first segment is inserted.

Choose a fishing line for a trimmer

The fishing line for the trimmer should be strong, stiff and flexible. in the trimmer it serves as a working tool for cutting grass. Flacks of different thicknesses are made. from 1.2 mm to 4.0 mm. Most models are designed for the maximum thickness of the thread of 3 mm. What is the diameter of the fishing line for the grass for grass in one case or another depends on a number of factors.

Depending on the hardness of mowing vegetation:

It is important to consider that too thin thread accelerates the wear of the motor, too rough. will accelerate its overheating and premature failure.

The structure of the cord of the fishing line matters:

• round. universal, most durable, for rough grass;
• curly. for soft plants;
• Twisted with notch. for thin long stems.

Important! Choose a fishing line for a trimmer of the type and parameters that the manufacturer Motokos recommends. Such material will work for a long time and efficiently with optimal loads on the product of the product.

How to change a fishing line for a trimmer on a trimmer

The fishing line for a trimmer is wound on a coil (bobbin), which is located in the body of the head of the trimmer for the grass. First, unscrew the head from the bar with the motorcycle cord and open it the top cover, pressing on the side latches. In some models, the case simply spins.

We take out the coil, clean it from dirt, the remains of the old fishing line. Coils are one- and two-section.

Fishing line winding on a single.section coil

We take 2 m of fishing line, we spread it up to half through a special hole inside the coil. The ends of the fishing line of the same length stick out from both sides. We wrap them with both along the groove of the coil in the direction indicated by the arrow on the case (back to the rotation of the coil on the shaft of a trimmer for grass). We do not wound the fishing line for the trimmer to the end-pieces of 10-15 cm, which will be workers, fix in grooves on board the coil. Fixation is needed so that the fishing line for the trimmer is not unwound when installing it in the head of a trimmer for grass.

We insert the coil into the body of the head, while at the same time we spread the free ends of the fishing line into the holes of the body, set. We collect the head, put it on a trimmer for the grass. Everything, the change of fishing line in the trimmer was carried out.

How to wind a fishing line for a trimmer for a trimmer for grass with a two.section coil

If there are two sections in the coil, put the fishing line for the trimmer in half and insert the fold place into a special groove in the side between the sections. We begin to wind the ends each in its own groove. then everything, as in the case of a single.section coil.

How much fishing line is wrapped on a trimmer for grass? You can wind 2-4 m, depending on the product model. In each case, it is impossible to wind too tight, the thread should have a free move for stretching during operation.

Shaving

The device was originally intended only for haircuts and trimming, subsequently began to make trimmers for shaving grass, ordinary cars. a special nozzle is intended for this.

• Writing start up from the bottom up from the kadyk, and remove the hairs below the kadyka with a safe razor.
• When shaving the neck, it is recommended to use a slow speed limit.
• The flat part of the nozzle should fit tightly to the skin.
• If the bristles have grown long, it is required to reduce it as much as possible with a ridge and only then use a shaving trimmer.

Fishing winding

Tramoring the fishing line in a trimmer coil for grass is a relatively simple procedure, provided that you adhere to a certain algorithm of action. When you need to determine how many meters of consumables are enough, wind it on the bobbin so that the skein does not exceed the diameter of the sides. Having decided on the length of the cord, follow the following instructions:

• Fold the consumable material so that one end of the fishing line is 10-15 cm longer than the other.
• You need to start charging with the central side, which divides the backpack of the trimmer for the grass into 2 parts. Find a groove where the cord should be inserted. The latter is bent twice.
• Determine in which direction you need to wind the fishing line for the trimmer. To do this, take a look at the bobbin on which there can be an arrow or inscription. She indicates the side of winding. If there are no designations on the coil, then look at the arrow on the mowing head. carry out windings in the opposite direction.
• Wash the consumable material carefully, a round to the round. Try to adhere to maximum thread tension.
• After completing the cord laying, fasten first the short end of the material. To do this, insert it into the groove on the side of the coil, which is suitable in diameter. The second end (more authentic), attach to the groove on the other side of the backpack of the trimmer for the grass.
• By fixing the fishing line for the trimmer, cut its ends. Do not forget to leave allowances about 10 cm.
• Install the refitted coil to the mowing head of the device. To do this, you need to insert and pull the thread alternately into the weekend of the head, then place the keyboard of the device in the skin.
• By applying the required force, pull the cord from the fixing grooves and tighten the material. At the end of this action, put on the lid and fix it using the latches.

The step.by.step winding of the fishing line on the coil to wind the cord per trimmer for the grass can be also in another way, in which two segments of the material are charged instead of one. The replacement is carried out like this:

• Bend one end of the cord thread in the form of a hook.
• At the bottom of the bobbin there should be a hole that is designed to fix the fishing line. Insert the bent over the end of the thread there.
• Wind the cord material in the direction of the arrow to the desired level, which does not exceed the diameter of the coil of the trimmer for the grass.
• The same actions need to be done for the second cell of the bobbin.
• Assembly of the device head is similar to the first way.

Fishing winding

Tramoring the fishing line in a trimmer coil for grass is a relatively simple procedure, provided that you adhere to a certain algorithm of action. When you need to determine how many meters of consumables are enough, wind it on the bobbin so that the skein does not exceed the diameter of the sides. Having decided on the length of the cord, follow the following instructions:

• Fold the consumable material so that one end of the fishing line is 10-15 cm longer than the other.
• You need to start charging with the central side, which divides the backpack of the trimmer for the grass into 2 parts. Find a groove where the cord should be inserted. The latter is bent twice.
• Determine in which direction you need to wind the fishing line for the trimmer. To do this, take a look at the bobbin on which there can be an arrow or inscription. She indicates the side of winding. If there are no designations on the coil, then look at the arrow on the mowing head. carry out windings in the opposite direction.
• Wash the consumable material carefully, a round to the round. Try to adhere to maximum thread tension.
• After completing the cord laying, fasten first the short end of the material. To do this, insert it into the groove on the side of the coil, which is suitable in diameter. The second end (more authentic), attach to the groove on the other side of the backpack of the trimmer for the grass.
• By fixing the fishing line for the trimmer, cut its ends. Do not forget to leave allowances about 10 cm.
• Install the refitted coil to the mowing head of the device. To do this, you need to insert and pull the thread alternately into the weekend of the head, then place the keyboard of the device in the skin.
• By applying the required force, pull the cord from the fixing grooves and tighten the material. At the end of this action, put on the lid and fix it using the latches.

The step.by.step winding of the fishing line on the coil to wind the cord per trimmer for the grass can be also in another way, in which two segments of the material are charged instead of one. The replacement is carried out like this:

• Bend one end of the cord thread in the form of a hook.
• At the bottom of the bobbin there should be a hole that is designed to fix the fishing line. Insert the bent over the end of the thread there.
• Wind the cord material in the direction of the arrow to the desired level, which does not exceed the diameter of the coil of the trimmer for the grass.
• The same actions need to be done for the second cell of the bobbin.
• Assembly of the device head is similar to the first way.

How to replace or put a starter spring in place?

If everything turned out to be in order with the rope at the starter, the suspicion falls on the coil itself. It is driven by a strip spring rolled into a roll. To change the spring, certain steps should be taken.

• Remove the starter from the lawn mower.
• Remove the starter coil.
• Unscrew the main bolt holding the pulley on the case.
• Pull out the exciting antennae and the spring, the strip spring is almost completely straightened or folded by rings of a larger diameter.
• Hold it in advance.
• Check if the spring is valid (there may be rusty stains, breaks, etc. D.). If the hooks at its ends are torn off, new ones will not be able to bend. high.carbon steel breaks when trying to bend it. Weakened hooks are suitable for easy bending.
• Make sure that an auxiliary (ordinary) spring with washers in place. These details protect the coil frame from taging the end of the main spring. If the washers and the spring are broken, but there are no new ones, do not screw the coil bolt hard, but watch it. He can unscrew and get lost.
• If the main (flat) spring of damage, insert the same new. Put a hook at the end of the spring in its place and bend it, inserts a round behind a turn into the space where it should be and should be.

The rewinding of the spring is performed in a minute. Oknovka in this action is gained quickly.

How to replace or put a starter spring in place, see the following.

How to insert a fishing line for a trimmer into a trimmer for grass?

Refueling a mowing coil of cutting thread for a trimmer for grass is not a complicated occupation, however, novice gardeners will have to practice a little to be able to quickly insert the cord into the existing household trimmer for the grass.

There are several ways to refuel a mowing head of a trimmer for grass. The first method is the simplest and is well suited for beginner gardeners.

In this case, the cord is inserted into the coil in the following sequence:

• First, you will need to reinforce from a common spray of about 6 m fishing line for a trimmer for grass, and then cut the resulting segment in half. As a result, 2 threads should be obtained, 3 m long;
• Then, at one of the ends of the first segment, you need to make a peculiar hook, and insert it into one of the through holes located in the upper part of the spool;
• Next, you need to start wrapping the fishing line on the spool in the direction indicated by the arrow. During winding, it is necessary to ensure that the fishing line for the trimmer evenly lays on the surface of the spool, and does not go beyond its upper section. It is not necessary to wind the segment until the end, about 15 cm of thread should remain in the hands;
• The remaining free end of the wound cord will need to be inserted into one of the recesses located in the upper part of the spool;
• Further, the same procedure will need to be done with the second piece of fishing line. It will need to be wound on the lower section of the spool;
• As in the first case, you do not need to wind a fishing line for a trimmer to the lower section. The remaining piece of thread will need to be inserted into the second groove of the spray.

After the operation performed, the coil will need to be installed on a trimmer for the grass and start it. To check the reliability of fastening the thread, you will need to press the gas lever to the end so that the engine reaches maximum speed. If the fishing line for a trimmer does not fly out of the head, then the fishing line for the trimmer is held reliably, and during the mowing of the grass it will not fly out of a braid coil.

How to wind a fishing line for a trimmer to a trimmer to grass?

The second method is a little more complicated in independent execution.

You need to wrap the cord for a trimmer for grass in the following order:

• First you need to cut off the total amount of approximately 6 m of the cord, and bend it. In this case, one of the parts should be slightly larger than the second;
• Then the thread of the place where it was bent will need to be inserted into a recess located on the dividing line between the two sections of the spool. As a result, the first part of the segment should be in the upper, and the second. in the lower section of the spool;
• After that, you need to start wrapping the fishing line. You need to do this in the direction of the arrow indicated on the corn. During winding, the cord should not be interpreted. The upper part of the segment should be neatly wound on the upper, and the lower. on the lower section of the spray. After that, two 15-centimeter segments of the cord should remain free;
• Further, the remaining ends will need to be inserted into the recesses located in the upper part of the spool;
• Then the fixed ends must be stuck into the through holes of the braid head of the trimmer for grass.

At the end, you will need to connect all parts of the mowing head, and pull each end of the fishing line a little. The finished coil will need to be installed on a trimmer for the grass and continue to work on the site.

Replacing the fishing line with a disk or knife

When ennobleing a personal plot, park zones and other places where various plants are required, it is often necessary to change the cutting tool in the trimmer. This is dictated by the fact that the standard cord installed in a mowing head can only cope with herbs. But when a shrub or young growth of trees appears on the path of an employee, a fishing line for a trimmer cannot cope with such a task, and it requires a change to a more effective cutting tool.

Manufacturers of trimmers provided such situations, and complemented their products with a mass of nozzles in the form of knives with several “petals” or in the form of disks similar to circular saws.

If you replace a fishing line for a trimmer with a knife with several “petals”, then such a tool can be mowed by both high grass and plants with thick and dry stems. And changing the fishing line for the trimmer to the disk, the user of motorcycles has the opportunity to cut shrubs or small trees.

Knives and discs are installed according to the following algorithm.

The first thing you need to remove, stagnating the shaft, a mowing head (twist clockwise) or a nut with anthers if the unit has not yet been used.

For a better understanding of the process of changing the tool, you can watch this video.

Problems with fishing line

Trimmeres users, both gasoline and electric, sometimes have problems with the cord. “Advanced” Kosilov owners can easily cope with the difficulties, realizing why this is happening, and for beginners, this is a problem that does not have a rational explanation. But in fact, everything is solved quite simply. The most common problems that happen to the fishing line are the following.

Cords of cord

If a trimmer fishing line is often torn, this can cause the following reasons:

• Stones, small branches and other hard obstacles come across the grass;
• The user mows the grass back to the fence, and if he is mesh, then this breaks the “antennae” even faster;
• poor quality of the cord (it is recommended to purchase high.quality);
• The output holes are worn out in a mowing head, which is why the fishing line for a trimmer is erased on the sharp edges of the bushings and breaks off (a complete replacement of the part will be required).

Large cord consumption

Basically, the cord quickly ends if you often knock on the ground with a semi.automatic head or press it hard. The coil unlock occurs, and the fishing line for the trimmer, lengthening, is cut off with a knife. Another reason that the cord quickly ends is the improper operation of the device with an automatic head: the user during kosbe often drops engine speed. But as we recall, the automatic head is arranged so that it is with each reduction in the revolution that a new portion of fishing line is supplied, so it is quickly consumed.

The thread does not hold

It happens that the thread is unwound if the spring weakened in the semi.automatic head. The fishing line for the trimmer is constantly extended and cut off with a knife installed on the casing, which increases its consumption. To check this, remove the casing and turn on the unit. If the fishing line for the trimmer “climbed”, then you will need to replace the spring.

a fishing line for a trimmer flies out

The reason that the cord after starting the unit is unwound is also a weakening of the spring inside the head. In addition, there are times when when the unit is turned on, a spitter head is scattered, and the spring installed in it is lost. Inexperienced users do not notice the absence of a spring and collect this node without it. Therefore, the cord does not hold, and under the influence of centrifugal force flies out.

The cord is not served, the coil does not spin

Automatic or semi.automatic head should serve a fishing line for a trimmer without stopping the unit. But if it does not come out, then the reasons may be as follows:

• The fishing line for a trimmer in a coil is incorrectly wound, which is why the latter does not spin;
• The cord is wound unevenly, and the thread can get stuck between the turns (the thread should be wrapped neatly, the turn to the turns, without distortions);
• Too short ends of the threads come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the fishing line is not supplied for the trimmer (it is recommended to always adjust the length of the cord before starting the unit, slightly pulling it up);
• The fishing line for the trimmer is sticking together (it will be considered later).

The thread sticks together

This nuisance occurs most often due to the use of poor-quality cord. When the apparatus is operating, the head of the trimmer for the grass heats up, and a poor.quality fishing line for a trimmer in it melts, gluing among themselves. Also, sintering of the threads occurs when a fishing line with a solid obstacle occurs. In this case, there is a sharp braking of the cord, after which it drags it into the head, where it bothers. Some unit owners recommend lubricating the cord with mineral oil or spray on it with a silicone spray after winding on a spul. Others advise to wrap less threads on the coil. But it is better to immediately buy a quality product, in the manufacture of which the manufacturer took into account the factor of overheating of the head, and the thread will not stick together.