How to get a motorcade Huter GGT. Correct starting correctly!

How to start a trimmer for Huter grass correctly

For independent preparation of the combustible mixture in a dosed amount, heat.resistant branded engine oil recommended by the manufacturer is used.

  • The specifics of this lubricant consists in the use of internal combustion with air cooling in high.speed engines, which are equipped with a chainsaw for home and a professional class.
  • Depending on the time of the year, for the preparation of the combustible mixture, motor oil of different densities is used, which retains the characteristics in the temperature range indicated on the label.
  • For use, branded oils are recommended, which provide a complete lubrication of the piston group and a crooked-shaped mechanism in all operating modes of the power unit.
  • Brand products are different in color. In particular, Calm mineral oils have red, synthetic color. Husqvarna motor oils have blue or green.

Even with a lower cost of mineral oils, it is recommended to use the advantages of synthetic counterparts for the preparation of high quality fuel mixture.

Risks of using fuel and lubricants substitutes

Features of the design of the ICE chainsaw of a domestic and imported assortment exclude the use of more affordable substitutes for biofuel and gas condensate. The productivity of such fuel is far from ideal.

According to various sources, counterfeit lubricants make up 8 to 15% of the total sales of motor oils. Only an experienced specialist can distinguish original products from fakes.

To eliminate potential risks of early failure of the saw. It is recommended to purchase supplies at company points and dealerships

With all external similarities, it is forbidden to use oils for two.stroke internal combustion of mopeds and light motorcycles for the preparation of a working fuel mixture. The use of not recommended lubricants can lead to a guarantee for maintenance.

Features of the preparation of the mixture

For security reasons, it is recommended to prepare the fuel mixture in a non.unit metal canister.

  • Recommended proportions of gasoline and oil for each model are different. In most cases, the ratio is 50: 1 and 40: 1. Basils operating on a mixture of gasoline-oil in a ratio of 25: 1 are much less common.
  • According to manufacturers of branded chainsaws, their products do not need to break. However, in the first hours of work, experts advise to operate a new chainsaw on the fuel mixture with high m oil and, if possible, in sparing mode.

For the preparation of the working mixture, containers with built.in dispensers are convenient. The selectivity of fuel filters at gas stations in some cases leaves much to be desired, so it is recommended to filter gasoline through suede or non.fiber material.

Following these recommendations will save you from spontaneous failure in the work of your carburetor equipment.

The specific characteristics of mineral or organic chain oils are focused on lubrication and cooling of besieged dust, so they are not suitable for the preparation of the fuel mixture.

Recommended sequence

According to the standard fuel mixture preparation technology, the estimated amount of oil is poured into a half.filled tank.

The mixture with a closed cork is thoroughly mixed, after which the remaining gasoline is poured. This sequence contributes to the uniformity of the composition.

It is advisable to prepare fuel for a chainsaw in an amount sufficient for one.time operation. The finished composition at a standard temperature of 20 ° C can be stored for no more than one month. At higher temperatures, the expiration date decreases to 2 weeks.

The mixture with the expired shelf life initiates the formation of tarry compounds, contributing to the clogging of sopels, the formation of soot and the limitation of the mobility of the piston rings. In order to save money, the re-executed composition can be consumed by adding up to 15-20% of the total volume to the fresh mixture.

The first launch of a trimmer for grass

When everything is checked and the prepared fuel mixture is flooded into the tank, there comes the moment of the first launch of the trimmer for the grass before its rolling. This is necessary

  • Place a motorcycle on a flat horizontal surface;
  • We move the air damper control lever to the position closed;
  • We pump up the fuel in a carburetor with several pitching of the primer;
  • Turn on the ignition toggle switch;
  • Smoothly pull the launch cord until you feel resistance;
  • After that with a cord 3 4 sharp jerks, until the lawn mower should be launched;
  • After starting, open the air damper.

If the lawn mower does not start or staller the first time, slightly open the air duct damage on the carburetor and try to run again.

Peculiarities

If we talk about the features of the models of this manufacturer, then to begin with, it should be said that this company from Germany was founded in 1979. All equipment that is produced under this brand is created by qualified engineers and developers and is tested at each stage of creation. In general, the lawn mowers of this German company are powerful and quite productive models. Their use allows you to cut the grass literally in any conditions. Very often the best models of this company are used for professional purposes. One of the important features inherent in all manufacturer models is that Huter motorcycles are equipped with a two.stroke air cooling engine and electronic ignition. This option makes it possible to ensure high power of the device and high.quality performance of the task.

Advantages and disadvantages

You should say a little about the strengths of the gasoline trimmers of the aforementioned manufacturer. The main ones can be called the following:

  • the presence of a two.stroke engine with a capacity of just more than 3 horsepower, which has air cooling and electrical firing;
  • A tank made of translucent plastic, which allows you to know exactly how much fuel was spent during operation;
  • The opportunity for a person to work comfortably. this is achieved due to the presence of an ergonomic handle according to the type of bicycle and a special mechanism of extinguishing various kinds of vibrations;
  • A high.quality cutting set in the form of a cutting knife and fishing line of high strength is used here;
  • There is also a wide capture when running. 25.5 centimeters, which makes it possible to effectively and quickly mow grass, shoots and other greens;
  • a protective casing that protects a person from the ingress of mowed grass, stones and a variety of garbage;
  • shoulder belt that allows the operator to work for a long time and not feel fatigue;
  • Simplicity of service and work. the principle of operation and the device of models from Huter are very simple, which will easily understand their use even an ignorant person;
  • Reliability-such a gasoline trimmer for grass can work for a long period of time without stopping, while it does not heat up due to the features of the air cooling system;
  • the possibility of unhindered movement around the site. given that gasoline trimmers for grass, unlike electric ones, are completely independent of the presence of a socket, which guarantees a person freedom of movement.

At the same time, there are a number of shortcomings that cannot be mentioned, namely:

  • noise during work. gasoline trimmers for grass not only from Huter, but generally vibrate quite strongly and publish a strong noise, which creates uncomfortable working conditions;
  • Contamination of nature. models working on fuel, during operation form various kinds of exhaust gases, which harm the environment;
  • High cost. trimmers for grass of the described type have high cost due to the fact that they have high performance and good technical characteristics.

In the context of the above, it is safe to say that such devices have more advantages, which means that their use is justified.

How to refuel a trimmer for grass

The finished mixture of gasoline with butter can be stored for no more than 3 months (clean gasoline is stored less). Dilute the fuel in the quantity that is enough for several applications of the trimmer for the grass. In general, prepare:

  • gasoline and oil, which is suitable for two.stroke engines with an air cooling system;
  • metal canister and a mixture container;
  • respirator;
  • gloves.
  • Pour 1 l of gasoline into a suitable volume of 1 l of gasoline and add 1/2 of the desired amount of oil.
  • Mix carefully, being at a decent distance from the sources of open fire.
  • Add the rest of the oil to combustible and mix everything again.

General recommendations for refueling a trimmer for grass with a two-or four-stroke engine:

  • Place the fuel tank so that the cover is located on top, and then pour the required amount of fuel.
  • Do not overfill the fuel tank. This will lead to one of the problems: transferring into the intake pipe and fuel filter, flammable ignition or breakdown of the motor.
  • Try to fill the mixture so that it does not spill. To do this, you can use the watering can.
  • If you still poured fuel, then immediately wipe it. Put the wiping material, do not accumulate indoors. this is fire hazardous.
  • The launch of the device should begin after the canister with fuel is removed at a distance of more than 10 m.
  • If there was a long break between the operations of the mowing, then the remaining old fuel be sure to drain.

We proceed to running the lawn mower

After starting, do not rush to immediately run the trimmer for the grass. Let the engine idle for 5 minutes. While heating is going on, adjust the air supply to the air damper with a lever so that the rogue with a fishing line or with a knife does not rotate. As soon as the tool warmed up, we completely open the air supply to the corresponding lever to the “ON” position and squeeze the gas trigger for 1/2 and hold the seconds of seconds 30. Then we drop the gas, let the trimmer work on xx 30.40 seconds. In this mode we continue 10 minutes 15. Then we mock and let it rest for 15 20 minutes.

Having cooled the lawn mower, we continue to run the engine according to the previous scheme. Start a hot, a trimmer for grass should already be with an open air damper. Try not to hold the gas for a long time, since the movable details of the tool only rubbing each other. And do not let the engine work at idle for a long time as it can overheat.

The next stage is the run.in a gas reducer gearbox for grass. To do this, select a plot with soft young grass. Kosim 5 10 minutes with 1/2 2/3 from full gas. After we take a break for 20 25 minutes. Repeat the cycle 3 4 times.

In general, therapist for the lawn mowing according to the described algorithm is carried out until the fuel mixture in the tank is fully generated. After which the tool is ready for long.term work. In the process, follow the temperature regime of the gearbox and the motor. They should not overheat.

Instructions for Huter GGT-1000T

3. four. 5. 6. 7. eight. Introduction. ………………. 3 Technical characteristics …………………… 5 Operating instructions ………………………………………………………………………………………….………… 8 technical

ATTENTION! Exhaust gases are toxic and dangerous for health. It is forbidden to launch the engine of the product in a closed or poorly ventilated room. Gasoline and its pairs are easily ignited and explosive! Technical characteristics model engine type of ignition volume, cm3 engine speed, rpm

The device of a trimmer for grass 1 2 3 4 5 6 7 8 9 10 11 12 assembly handle Starter Starter Starter control lever cap of a high.voltage wire lid Fuel tank lid Leville handle Handbone Corps Fuel tank right handle control hilt of the handle mount

The control handle for mounting the control handle to the bar uses the control unit of the control handle. It consists of the upper part of the mount, fasteners, lower and middle parts of the mount located on the bar. The procedure for installing the control handle on the bar. Take the average

Installation of the shoulder belt attach the carabiner of the shoulder belt to the ring for fastening the shoulder belt. To ensure the better balancing of the product, adjust the position of the ring for fastening the shoulder belt on the rod of the product, having previously loosened the fasteners of the ring. After adjustment

and in the hole in the hub of the shaft. 5. Installation of a coil with a fishing line combine a hole in the shaft hub with a hole in the gearbox cup. Insert a metal stopped rod into the hole in the gearbox cup and in the hole in the shaft hub. Unscrew the mounting nut from the hub of the product. Remove the cup with

Strong jerks of an unnecessary cord, stretching the cord to the stop can cause a breakdown of the starter mechanism. 7. Set the air damper lever in the middle position (rice.12). eight. Turn the starter handle several times until the engine starts. Let the engine warm 5-10 seconds. 9. Lever arm

Pull out the air filter and thoroughly rinse it first in a soap water solution, then in pure warm water. Dry the filter at room temperature, soak it with 2-3 drops of motor oil before installing the filter (rice.16). Rice.15 Fig.16 2. The spark plug regularly check

huter, correct, starting, correctly

The malfunction of the engine does not start the cause of the ignition switch is in the Stop position “Turned off”. Empty fuel tank. Rubber cap of manual swing of fuel presses the carburetor pour over the fuel (due to the improper order of launch). Old or incorrectly cooked fuel

Service Centers: Unified Technical Support Service Tel.: (495) 318-05-42, 318-05-57 Astrakhan, st. Latysheva, 7, tel.: (8512) 628-262. Belgorod, LLC Agrootorgservis, ul. Karachanskaya 399, TSC “Successful”, tel.: (4722) 587-277, 207-256. Vladimir, st. Bezimensky, d. 56, (4922) 44-68-90

Certificate of acceptance of the gasoline trimmer for grass “Huter” of the GGT series of the GGT _ No. _ recognized as a suitable for operation, the date of sale _ I am a buyer/representative of the company with the terms

Dear buyer! We express you great appreciation for your choice. We have done our best so that this product satisfies your needs, and the quality corresponds to the best world samples. The manufacturer company sets the official service life for gasoline trimmers for grass for 5 years, at

Checking the ignition system

If the trimmer for the grass has already been used, then check the serviceability of the removed (at the moment) candles, changing it places with any other. If, when examining a candle, for example, a ceramic dielectric crumbled, electrodes bent. buy exactly the same, focusing on the product code, knocked out on the parts itself and checked it with a marker in the operating manual of a trimmer for grass. A candle without an insulator and/or with bent electrodes will not give normal sparks when triggered.

If the candles are in order, but the fuel is not observed, check the ignition coil using an ohmmeter (multimeter). Lack of indications (infinite resistance). a sign of a shift in the winding. If it was spent on overheating due to inter-flip circuit, there will not be enough stress for spark breakdown.

Since a very thin wire is used for it, so it converts 12.6 volts from the battery of 30,000, it is very difficult to fix it (rewind) in garage conditions. You will need to replace the coil.

Engine cleaning

If the trimmer for the grass did not start in use, and suspicion falls on a dirty engine, then before starting it will require cleaning it. To wash the carburetor using a special solvent, make the following.

  • Remove plastic caps and air filter.
  • Having gained access to the carburetor, remove it and disassemble it.
  • Release the stream of solvent into the main jet or other engineering channels (through washing). Make sure that there is nothing extraneous on the motor.
  • Collect the entire system in the reverse order. Prepare the desired fuel mixture (if the engine is 2-stroke) or pour separately into each of the tank (if the engine is 4-stroke) suitable oil and gasoline.
  • Repeat the steps to start the engine from the previous instruction.

If the launch failed, a complete disassembly of the carburetor, valve adjustment, checking the pistons, full.fledged cleaning of the nozzles will be required. The stadium of this process changes depending on the type of motor.

Preparation of the fuel mixture and refueling

For the convenience of making fuel mixture, it is better to have a special canister. where one part contains gasoline, and in the other 2 stroke oil. We recommend getting similar, it is very convenient to use https: // ru-sad.RU/Prinadlezhnosti-Dlya-Sadovoy-Tehniki/Dlya-Benzopil/Kanistryi/

Next, take a measured container, with a scale applied to it, with its help you can prepare the mixture as accurately and quickly as possible. See in the instructions which brand of gasoline and 2-stroke oil https: // ru-sad.RU/Prinadlezhnosti-Dlya-Sadovoy-Tehniki/Masla-I-Smazki/recommended by the manufacturer of your lawn mower model. Pour gasoline and oil into a container for the preparation of the fuel mixture, according to the proportions specified in the instructions. Then the finished mixture neatly, through the funnel, pour the trimmer for the grass into the fuel tank. The ratio of gasoline and oil should be just the same as indicated in the instructions. This is a very important point!

Launching a lawn mower with an unfinished engine

For the first launch of the lawn mower, find the air damper lever and put it in position “Closed”. Turn on the ignition on the handle. If your model has a manual fuel pump, the people are called a suction, then click on it 3-5 times until you see the fuel mixture inside the primer. Now the tool is ready to launch. Put a trimmer for grass on a flat surface to ensure a stable position. Smoothly stretch the trigger cable until you feel its resistance, and then pull the cord with a sharp movement 3-5 times.

If the engine started after 5 jerks, then open the air damper. If this does not happen, still open the air damper (with an open damper and continuation of attempts to start the engine, the fuel flows a candle and you will have to dry it, and this is extra waste).

If the engine does not start, with an open damper, then close it to continue to pull the cord. The first launch may be quite difficult and demand up to 15 jerks. After the engine has begun to work, click once on the gas lever, so you will use idle. Now let the engine work and warm up. After that, it can be stopped by pressing the “Stop” button.

Fuel pouring through the openings for candles

If there is no manual pumping on the engine of the trimmer for the grass and the device did not start, pour a little fuel into the motor itself through candle moves. Make the following.

  • Check if the fuel level is sufficient in the tank for draining a small amount of it. It takes only 20 ml.
  • Remove the cap from the candle and unscrew it with a candle key.
  • If the candle is polluted on the former use of the trimmer, rinse and buy it. There should not be any deposits on the electrodes of the candle. Do not damage the ceramic insulator of the central conductor. In the new trimmer, check the candles for the factory defect.
  • Return the candle back and check the spark look (category between electrodes) when the starter triggers.
  • Remove the candle again. Using a 20- or 50-cup syringe, pour 20 ml of gasoline into a candle hole from under a candle.
  • Insert and fix the candle by setting the magnitude of its technological clearance at least and no more than a millimeter.
  • Skip fuel using a button (or lever) of swinging. if it is on your model of a trimmer for grass. Press the button every 4 seconds.

Now try to start the motor. Close the air conditioning immediately after starting.

Safety measures when spent

What are the safety measures when working with a trimmer? There are several simple and understandable points, following which, you can avoid dangerous situations and minimize the possibility of injury:

do not use a trimmer for grass in raw and wet weather (especially an ethletric trimmer for grass); In front of mowing, dress in dense clothes so as not to injure the skin with pieces of grass of stems flying away from the disk or fishing line with high speed;

observe a distance of 15 meters from other people and pay attention to the signs that others can serve; use headphones or berushi;

  • Using an ethletric trimmer for grass, make sure that the wire from the extension cord always remains behind;
  • put on dense rubber boots, which after work are easy to clean;
  • use gloves and protective glasses to avoid small pebbles in the eyes and respiratory tract;
  • Upon an injury, immediately consult a doctor.

Putin’s Temper Tantrum Emboldens Ukrainian People | The Daily Show

In addition to the above, do not forget to look around, suddenly an obstacle awaits you ahead or side. Suburbating the bar with the blade into thick thickets of grass, it must be remembered that there can be stone, stump, or berries (for example, strawberries). Working with a trimmer requires composure and attentiveness, but by understanding simple rules, it will become familiar, understandable and will bring only positive emotions from the results obtained.

How to start a trimmer for Huter grass correctly

How to start a trimmer motor for grass or lawn mower?

The new trimmer for the grass is simple in commissioning.

  • Check the type of device motor. Trammers for grass are equipped with a 2- or 4-stroke engine.
  • Buy oil for this type of motor. Gasoline for a trimmer for grass-AI-92/93/98, is sold at all gas stations.
  • Mix oil with gasoline. Mineral oil is mixed in a ratio of 1: 34 with gasoline, synthetics. in 1: 50. Follow the tips of the trimmer manufacturer for the grass for the viscosity of the oil (see. label on the flask). often use all-season oil 5W-30. Do not use unverified car.
  • Pour a small amount (for example, 0.5 liters) of the resulting fuel in the tank.
  • Close the air conditioning by shifting the suitable lever (see. annotation).
  • Turn the ignition key (or handle) to the “inclusive” position. without this, the trimmer will not start for the grass. Newcomers often make such a mistake.
  • Skip a little fuel in a carburetor. if there is a manual “rocking” with a separate button or lever (see. annotation). We need 4-7 presses.
  • Install Trimmer for grass On a flat surface.
  • Carefully pull the starting cord until you feel its brake. Then abruptly pull it out, but not quite. Repeat this movement before 4 times.
  • If the engine does not start, open the air damper again, it will flood the candles with a different gasoline during subsequent movements of the cord. Make 2-3 samples to start an open handbrake motor.
  • If the motor does not start, close the damper and make a few more attempts to it Bind.
  • After starting the engine, click on the gas lever, turning on the idle.

How to start a gasoline Trimmer for grass?

How to start correctly Trimmer for grass. the question that the owners are puzzled in the event of a breakdown of the device. And after the successful repair of the trimmer for the grass, the owner tries to avoid repetition of the same situation.

Starting the lawn mower for the first time or after a long downtime

The lawn mower differs from a trimmer for the grass in that a fishing line for a trimmer, but a mechanical gearbox or winch based on the gear equipped with a knife, acts as a cutter for grass. The knife drive is much more powerful than the forest mechanism. a powerful lawn mower is also used when cutting the bushes. Both Chinese and European law mmores do not differ in anything special when the declared capacity is real.

For lubrication of gear gears, Litol or solidol is used. Having checked the gearbox, prepare for the work and the engine itself. according to the above instructions. If the start has failed, the problem is already in the engine.

Prerequisites

The reason for which the trimmer for grass fails may:

  • tank overflow;
  • excessive fuel pumping into engines equipped with manual supercharger;
  • wear in the motor of valves, cylinders, nozzles, fist pushers and other mobile parts;
  • In the tanks, gasoline and/or oil ended;
  • not in order of the spark plug;
  • clogging of fuel or air filters;
  • the valves in the motor were resolved or burned.

Fuel pouring through the openings for candles

If there is no manual pumping on the engine of the trimmer for the grass and the device did not start, pour a little fuel into the motor itself through candle moves. Make the following.

How to make Hill Climb Racing in Godot

huter, correct, starting, correctly
  • Check if the fuel level is sufficient in the tank for draining a small amount of it. It takes only 20 ml.
  • Remove the cap from the candle and unscrew it with a candle key.
  • If the candle is polluted on the former use of the trimmer, rinse and buy it. There should not be any deposits on the electrodes of the candle. Do not damage the ceramic insulator of the central conductor. In the new trimmer, check the candles for the factory defect.
  • Return the candle back and check the spark look (category between electrodes) when the starter triggers.
  • Remove the candle again. Using a 20- or 50-cup syringe, pour 20 ml of gasoline into a candle hole from under a candle.
  • Insert and fix the candle by setting the magnitude of its technological clearance at least and no more than a millimeter.
  • Skip fuel using a button (or lever) of swinging. if it is on your model of a trimmer for grass. Press the button every 4 seconds.

Now try to start the motor. Close the air conditioning immediately after starting.

The main thing. Fuel mixture!

In this case, the remains of plastic plastic dissolved in the brutal environment are created in the combustion chamber so terrible things that you will definitely not be able. But you certainly remember how to store fuel forever.

What to do when the fuel was definitely normal, there is a spark, but a trimmer for grass does not start a gasoline? It is possible that you just flooded the candle with gasoline. In this case, it must be turned out, wiped with a clean rag and dry. By the way, it will be completely useful to check the candle for performance itself.

The carburetor of the lawn mower floods.

How can you drown the engine on a gas tank, to be inattentive. Just one awkward movement

After several jerks, he will start and stall, which is a normal phenomenon. Putting the damper to the working position, start the tool again and start working.

Why not start Trimmer for grass. the reasons

To determine why gasoline Trimmer for grass It is poorly started or constantly stalls, it is necessary to sequentially check the work of all the main components of the unit. It is especially important to do this after a long.term storage of a lawn mower. So, the main reasons for such a trimmer’s behavior for the grass are as follows:

  • The culprit that the lawn mower is not started, there may be a poor-quality oil-Benzine fuel mixture. It must be prepared strictly according to the instructions. The savings here are not at all appropriate, since it can lead to the failure of the entire piston group of a trimmer for grass. Do not cook too much fuel mixture, as excess gasoline will lose their qualities over time.
  • You should know that gasoline trimmers for grass of stamps such as STIHL, Husgvarna and some others do not start if they are filled with cheap gasoline with a small octane number. Therefore, for such units, it is necessary to use only high.quality high.octane fuel.

How to start a trimmer for grass gasoline Huter

How to launch a trimmer for grass. This is a question that the owners confuse in the case of failure of the device. And after the successful repair of the trimmer for the grass, the owner tries to avoid repeating the same situation.

The reason for the failure of a trimmer for grass is possible:

huter, correct, starting, correctly
  • Tank overflow;
  • Excessive fuel injection into engines with manual supercharger;
  • Wear in the engine of valves, cylinders, injectors, fist pushers and other moving parts;
  • Gasoline and / or oil end in tanks;
  • The spark plugs failed;
  • Fuel or air filters are clogged;
  • Incorrectly spelled out or burned valves in the engine.

The test begins with the presence of oil and fuel in both tanks and a small part in the engine system. The “empty” engine will not start, despite the full tank, and also overflow.

How to start a three.dimensional motor or bush?

The new trimmer for the grass is simple during commissioning.

  • Check the type of engine engine. Trammers for grass are equipped with a 2- or 4-stroke engine.
  • Buy oil for this type of engine. Gasoline for a trimmer for grass. AI-92/93/98, sold at all gas stations.
  • Mix oil with gasoline. Mineral oil is mixed in a ratio of 1:34 with gasoline, synthetic. At 1:50. Follow the recommendations of a trimmer manufacturer for grass regarding oil viscosity (see. Label on the flask). The most commonly used polyhedral oil. 5W-30. Do not use unverified motor oils.
  • Pour a small amount (for example, 0.5 liters) fuel into the tank.
  • Close the air damper, moving the desired lever (see. Instructions).
  • Turn the ignition key (or handle) to the “inclusive” position. Without this, the trimmer for the grass will not start. Beginners often make this mistake.
  • Download a little fuel to the carburetor. If there is a manual “rocking” with a separate button or lever (see. Instructions). 4-7 clicks are required.
  • Place a trimmer for grass on a flat surface.
  • Gently pull the starter cord until you feel its braking. Then pull it sharply, but not completely. Repeat this movement up to 4 times.
  • If the engine does not start, open the air damper again, otherwise the spark plugs are filled with gasoline during subsequent movements of the cord. Make 2-3 attempts to start the engine with an open manual brake.
  • If the engine still does not start, close the shutter and make a few more attempts to run it.
  • After starting the engine, press the throttle lever to activate idle.

Let the engine warm up. 5-10 minutes enough. Do not start mating grass immediately after a cold launch. The engine of the trimmer for the grass should start.

Starting the brush for the first time or after prolonged downtime

The lawn mower differs from the trimmer for the grass in that the lawn mower. This is not a fishing line for a trimmer, but a mechanical gearbox or a winch with a gear, equipped with a knife. The knife drive is much more powerful than the carriage mechanism. When cutting bushes, a powerful bush is also used. Both Chinese and European law mowers do not differ when the declared capacity is real.

Litol or solid oil is used to lubricate gears gearboxes. After checking the gearbox, prepare for the engine itself. In accordance with the above instructions. If when starting, a failure occurs, the problem is already in the engine.

Share fuel through the spark plugs

If there is no manual pumping on the engine of the trimmer for the grass, and the device does not start, pour a little fuel into the engine through the spark plugs. Make the following.

  • Make sure that the fuel level in the tank is sufficient to drain a small amount. It will take only 20 ml.
  • Remove the lid from the spark plug and unscrew it using the spark plug for a candle.
  • If the candle is contaminated with the used trimmer, rinse and bake it. There should be no deposits on electrode electrodes. Do not damage the ceramic insulator of the central conductor. In the new trimmer, check the spark plugs for factory defects.
  • Turn the spark plug back and check the ignition (discharge between the electrodes) when the starter lights up.
  • Remove the candle again. Using a syringe with a volume of 20 or 50 cm3, pour 20 ml of gasoline into a hole for the spark plug.
  • Insert and secure the spark plug, setting the value of its technological clearance at least and no more than a millimeter.
  • Pour the fuel with the shift button (or lever). If this is in your model of a trimmer for grass. Press the button every 4 seconds.

Now try to start the engine. Close the air damper immediately after starting.

Checking the ignition system

If the trimmer for the grass has already been used, check the condition of the removed (currently) spark plugs, replacing it with any other. If, for example, when checking the spark plug, the ceramic dielectric broke, the electrodes bent, buy one, guided by the product code knocked out for the parts itself, and check it with a marker in the instructions at the trimmer. A spark plug without a insulator and / or with curved electrodes will not give normal sparks when triggered.

If the spark plugs are in order, but the fuel sparking is not observed, check the ignition coil with an ohmmeter (multimeter). Lack of indications (infinite resistance) is a sign of winding winding. If it sins from overheating due to a short circuit, the voltage for the spark malfunction will be insufficient.

Since he uses a very thin wire that converts 12.6 V from the battery of 30,000, it is very difficult to fix (rewind) even in the garage. The coil should be replaced.

We select the revolutions correctly

What speeds should be mowed to cut the lawn evenly? When is it better to increase or lower the speed? How much time you can hold high speeds? It should be noted that all these issues are relevant only for a gasoline trimmer for grass. The ethletric trimmer for the grass does not have the ability to choose the frequency of the engine, it goes almost as much as possible to its peak power and works on it while both power buttons are clamped.

If the device itself allows you to adjust the engine speed during operation, then the following will be optimal:

  • minimum turns for working with lawn grass on a flat surface;
  • average turns when using a disk for high grass and non.thick bushes;
  • increased (maximum) revolutions for drilling bushes.

Do not start a trimmer for grass. how to find and eliminate the reason yourself?

If the motor motorcycles do not start, then this can talk about several tools of the tool at once. Start inspection and search for breakdowns should be from the spark plug. It will need to be twisted and carefully checked for clogging. If a thick layer of soil has formed on the tip of the part, then this indicates an excess of motor oil in the fuel mixture. To start a motorcycle, its owner must rinse the candle with gasoline and completely clean it from the car. Next, you need to damage the cylinder, pulling the starter’s cable several times. As soon as the candle dries, it needs to be screwed into the seat and try to get a motorcycle.

The reasons for the lack of launching of the motor can also be found in poor condition of the air filter. If, after prolonged use in the filter element, a large number of clogs have accumulated, then it will need to be cleaned and dried. If this could not be done, then the filter should be replaced. If a gas station is poorly started, then the cause of the malfunction often needs to be sought in the fuel hose. Due to banal wear or blow, he can break off, which will lead to pouring the fuel mixture. In this case, you will need to replace the hose. In the places of its joints, you will need to apply a uniform layer of silicone sealant.