How to get the line out of the trimmer

Method 2. how to properly put the line on the reel of lawn mowers with photo description and video

The second method differs from the first in that it is not a single piece of equipment that is charged into the coil, but segments from two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into a lawn mower’s line is the same as with the first method, and to make sure of this, below are detailed instructions:

  • There are two equal length pieces of material that you can use.
    line, trimmer
  • One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be secured
  • Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
  • The brace of the fishing line should be hooked on the bracket, and wind it in observing the direction of the arrow
  • The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
  • Manipulations with the second end of the fishing line are carried out in the same way.
  • The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the coil, the cover with the latches is installed

The above instructions on how to install a fishing line in the lawnmower will help not only correctly, but also quickly make the replacement procedure. Assembling the trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to conveniently fix the tool. Video instruction is presented below.

A few tips for properly threading the string into the trimmer

  • If the coil allows you to wind fifteen meters of thread, then you should not wind so much, ten is enough, that is, if you fold it in two layers, you get five meters. With a different line capacity, you should use the same rule.
  • In the case when an ordinary round thread is used, it is better that it be 3.3 mm in diameter. If this is a curly fishing line, then its thickness should be less, for example, 3 mm.
  • It is better to wind both segments of the fishing line on the spool at once, and it is necessary to start from its bend. It is important not to overlap in the direction of the arrow. It is also important to be able to pull the thread perfectly. If the thread is over-tightened, then it can overlap. If not reached, it can twist. In order not to cut your hands on the curly thread yourself, you should wind it with gloves.
  • No need to leave the ends of the line long. This can cause it to curl.

How to wind the line around the trimmer cutter head or lawn mowers

The video shows in detail how to wind the line on a trimmer reel or lawn mowers. Refueling with mowing line.

HOW TO REMOVE THE BALD LINE: BEST BLENDING TECHNIQUE

Now only I bite!

I caught this pike with a bite activator. No more fishing without a catch and looking for excuses for your bad luck! It’s time to change everything. The best bite activator of the year! Made in Italy.

Single-barbed trimmer spool

Single-barb lawn mowers reel

Many owners and specialists note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the trimmer reel.

After winding, you need to leave a free end of 15-30 cm to increase the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.

Trimmer head with two antennae

Head with two flutes

After removing the spool from the spool body, we determine the number of strands for winding the fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interlacing adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off the excess.

Trimmer head with automatic line threading

Trimmer head types

Some models on the market have a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of an automatic trimmer head include ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and high cost.

How to properly wind the line on the trimmer reel with your own hands: we paint the essence

What line is used for the trimmer? How to remove the spool from the trimmer? Threading bobbins with different types of bobbins. A few tips for properly threading the string into the trimmer.

What you need to know about trimmer line

A fishing line is a consumable made of nylon that serves as a cutting device. By means of this equipment, the grass is cut, which is ensured by rotating the tool head at a high frequency. This material has a different thickness, which depends on its use on the corresponding tools, low-power electric (from 1 to 1.6 mm), electric from 500 W (2 to 2.4 mm) and gasoline trimmers with lawn mowers (from 2.4 to 3. 2 mm).

The more powerful the tool, the correspondingly thicker the cutting equipment should be. This affects not only the quality of the grass cut, but also the service life of the material. If you are wondering how to wind the trimmer coil, then it is time to change and reload the tool. With the onset of spring, this question is becoming more and more popular, so it’s time to figure out the step-by-step instructions for replacing the line in the trimmer reel.

How to properly wind the line on the trimmer reel with your own hands. we consider thoroughly

Private home owners know how essential a trimmer tool is. It can be gasoline and electric, and they differ in the design of power units. For cutting grass in areas where there are stones, trees and other obstructing objects, a fishing line is used as a cutting device. This consumable wears out during use, so how to wind the trimmer coil, we will consider in detail in the material.

How to remove the spool from the trimmer and remove the line

Initially, remove the line from the trimmer spool before threading it into the trimmer spool. A reel or aiming device is a device that sits inside the mowing head, bobbin or drum. There are different types of heads (depending on the manufacturer), but the principle of replacing the line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it.

It is interesting! The tooling can be changed directly on the tool, but if you are doing this for the first time, it is still recommended to remove the head and study the detailed winding process. After the technology has been mastered, you can perform replacement work on a trimmer lawn mower or lawn mower.

The instruction on how to unscrew the manual head on the trimmer is as follows:

  • Turn the tool upside down and, if necessary, clean it from dirt. With two fingers of one hand, grip the cover latches (on the mowing head), which are symmetrically positioned to each other. After lightly pressing them inward, remove the protective cover from the drum
  • Next, remove the line spool from the drum shaft. It is mounted on a shaft without fasteners, therefore it can be removed with one hand.
  • The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with an appropriate tip or bit
  • To unscrew it, hold the drum base with one hand, and unscrew it counterclockwise with a screwdriver with the other.
  • After that, you can start dismantling. To do this, you do not need to pull it with all your strength, but by slightly shaking it to the sides, slowly disengage it from the metal shaft on which the drum is seated.
  • When reinstalling, fit the head into the square slots

This process is not difficult, and as you know, there is no need to dismantle the entire head if you know how the replacement is performed. When dismantling, consider the following nuances:

  • It is recommended to remove the head periodically to prevent corrosion of the threaded connection. If you never unscrew the screw, then if necessary, it will be difficult and even impossible to do this.
  • If the screw has a four-sided bore of the head, then for unscrewing it is necessary to select a screwdriver or bits of a suitable size in order to exclude the licking of the edges on the head
  • When assembling the unit, treat the threaded seat with lubricants, for example, grease or machine oil.
  • If the edges on the screw are licked, then special clamping pliers can be used to unscrew it.
  • There are drums that do not require preliminary disassembly. To dismantle them, grab it and rotate in the opposite direction of the clockwise direction

Knowing how to disassemble the drum, you should continue to figure out how to replace the trimmer line. The video below shows a detailed process on how to open the trimmer coil and disassemble it.

Trimmer head with automatic line threading

Trimmer head types

Some models on the market have a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of an automatic trimmer head include ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and high cost.

Step-by-step instructions on how to wind the trimmer reel and lawn mowers

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the reel. This information is usually presented on a tip, which will not allow you to make mistakes with the use of the appropriate equipment.

If there is information on the reel about the diameter of the line you can fill in, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the rig, it remains to figure out how to charge it. There are two ways to do this, but not all of them are applicable. We will consider both methods in detail, and depending on which models of lawn mowers and trimmers you use, you decide on your own which option is suitable.

It is interesting! The principle of how to wind the line to guide lawn mowers is appropriate not only for autonomous gasoline units, but also for electric trimmers.

Method 2. how to properly put the line on the reel of lawn mowers with photo description and video

The second method differs from the first in that it is not a single piece of equipment that is charged into the coil, but segments from two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into a lawn mower’s line is the same as with the first method, and to make sure of this, below are detailed instructions:

  • There are two equal length pieces of material that you can use.
  • One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be secured
  • Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
  • The brace of the fishing line should be hooked on the bracket, and wind it in observing the direction of the arrow
  • The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
  • Manipulations with the second end of the fishing line are carried out in the same way.
  • The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the coil, the cover with the latches is installed

The above instructions on how to install a fishing line in the lawnmower will help not only correctly, but also quickly make the replacement procedure. Assembling the trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to conveniently fix the tool. Video instruction is presented below.

Trimmer head with two antennae

Head with two flutes

After removing the spool from the spool body, we determine the number of strands for winding the fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interlacing adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off the excess.

Homemade trimmer line

Many users of mowers, both electric and gasoline-powered, some time after using a purchased line, ask themselves the question: what can be used to replace it? If you exclude dangerous options (chain from a chainsaw, a blade from a hacksaw, wire, cable, string, etc.) that can cause serious injuries to the user and others, then the best way out of the situation is considered to be a homemade fishing line from a plastic bottle.

How to cut a bottle into tape

Before you start making a homemade cord, you will need to prepare the material itself, namely a plastic tape of the required width and length. To dissolve a PET bottle onto a tape, various devices are used, the manufacturing algorithm for which can be found on the Internet. If you are going to mow large areas overgrown with grass, and you need a lot of homemade cord, then, of course, it makes sense to make a more complex bottle cutter from a corner or U-shaped aluminum profile. The process of making a bottle cutter is shown in this video.

But if you are not interested in mass production of plastic tape, then from time to time you can dissolve the bottle into strips in a simple way.

  • Take a regular PET bottle cork.
  • Cut it in half (but not completely).
  • Remove all bumpers inside the cork.
  • After folding the cut cork in half, pierce it through with a knife as shown in the picture below, being careful as the plastic is very hard. To facilitate the process, the tip of the knife can be heated.
  • Use scissors to cut the bottom of the plastic bottle (as straight as possible, without jagging). Insert the bottle into the fixture from the side where the knife blade is sharpened, and start to cut in a little. When a small strip appears, just start pulling it.

Thus, the entire plastic container will dissolve into a tape of the same width.

A -sized version of the bottle cutter, which you will always have at hand, can be made from a regular pencil sharpener, preferably made of aluminum. Details on how to make it are shown in this video.

How to make trimmer line

Cut tape from PET bottles, if wound on a trimmer, will mow, but not for long, since it is fragile and breaks quickly. It needs to be improved a little, and for this you need to do the following.

  • Insert one end of the plastic tape into a vise and clamp it.
  • The other end of the tape can be clamped in a drill or screwdriver. Insert it into the chuck of the screwdriver so that it holds well in it and does not jump out when pulled.
  • Turn on the lowest speed on the screwdriver and start twisting the tape, be sure to keep it taut, otherwise it will start to get tangled.
  • After the tape stops curling, without releasing the tension, begin to warm it up with a construction hairdryer. Since this plastic has heat-shrink properties (it shrinks when heated), the turns will be aligned and soldered.
  • While warming up the twisted tape, from time to time turn on the screwdriver and turn the rope to align the turns on it.
  • When you warm up the entire tape, you will have a homemade plastic rope that is quite flexible and durable.
  • In the event that you do not have a drill at hand, you can use a regular stick to twist the plastic tape, as shown in the following figure.
  • The construction hair dryer can be replaced with a regular lighter if you are making a short cord.

As practice shows, the trimmer line, made by hand from one twisted tape, mows the grass well, but if it comes across stones or branches on its way, it quickly wears out. To eliminate this disadvantage, it is recommended to weave a plastic rope from several ribbons, for example, from two or three. The following illustration shows a homemade cord braided from three plastic strips. Although it differs in thickness from a single cord, it is much stronger than the first one, and lasts a longer time.

Next, as usual, the trimmer line is inserted into the mowing head or wound on a reel, and then inserted into the head, after which the protruding ends are cut so that they do not touch the protective cover.

Thus, literally from scrap materials, a free trimmer line is obtained, which can be made in unlimited quantities.

Grass Trimmer ,