How To Give The Line To The Trimmer

Preparation. remove and disassemble the spool

On most electric and petrol trims, you will need to remove the spool to replace the line. The FUBAG tool lets you skip this step. To make the instruction universal, we will still consider it in detail:

Lock the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod.

How To Give The Line To The Trimmer

Unscrew the bobbin case. In our example. strictly clockwise.

Unscrew the cap according to the direction indicated on the body.

Take out the coil for winding.

The preparatory stage has been passed. You can proceed to winding the fishing line.

How to wind the line onto the trimmer spool

Winding Algorithm

Insert the resulting loop into the groove.

Lay the line in the direction indicated on the element body.

Insert the short end into the slot on the side of the spool.

Secure the long end in the opposite groove.

Place the spool of coiled line into the spool body.

Pull the line out of the locking slots.

Put on the cover and fix.

Trim the ends of the line, leaving 10 to 15 centimeters.

The replacement of the line is completed and now all that remains is to screw the bobbin onto the trimmer and you can work.

How to properly wind the line on the trimmer reel. Step by step guide. How to choose a fishing line. length, diameter, restrictions

As for the length, you should count on the estimated frequency of use of the trimmer. The more often, the more it costs to stock up expenses.

Information about the possible line diameter can be found on the body trimmer spools. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose the appropriate option, taking into account the characteristics of the cultivated area. The larger the diameter, the easier it is to mow tough grass.

ATTENTION! Typical line problems

No wonder they say: “Forewarned is forearmed“. Knowing about possible problems and the causes of their occurrence, you can prevent them in time. We recommend to remember or leave a memo.

Problem Cause Decision
Line break Stones, twigs and solid objects in the grass Avoid collision
Poor cord quality Replace with a quality analog
Wear of outlet holes in the head Complete replacement of part required
The line is unwound Loose spring in coil Check spring and replace if damaged
The line is sticking Poor line quality, due to which it can melt under the influence of temperature from the heating head Reel in less line or replace with a better line

For a better understanding of the mechanism of the process of changing the line in the spool with a guide prepared by FUBAG specialists:

We wind the line on the trimmer spool

Owners with their own plots often face the problem of lawn maintenance, namely the need for high-quality mowing of grass. For these purposes, either a hand or a scythe powered by electricity is used. a trimmer (see Photo). It is clear that working with the electric model is much easier and faster. The grass is mowed with a line rotating at high speeds. But during operation, the thread wears out over time and requires a change. So how to wind the line on the trimmer reel with your own hands?

Types of fishing line

The trimmer thread can be divided into types according to its diameter. It can start from the smallest. 1.2 millimeters and go up to 4 millimeters. The most commonly used is the 2 mm diameter. But it must be selected strictly individually, based on the specific model of the device. Often the required product diameter is indicated in the product passport. Usually, the more powerful the trimmer, the larger the line diameter should be. For example, it is best to wind a thread with a diameter of 2.4 mm on a spool of lawn mowers, and for a product with a weak engine, a thread diameter of 1.6 mm is suitable.

Fishing lines also differ in the type of section. It can be round (for mowing ordinary grass), square (for soft and often mown grass), with sharp edges (for tall grass), with notches (for thin grass), as well as complex (see photo). The latter can be refueled not in all types of devices. It should be noted that the line is intended exclusively for mowing grass. To cope with other types of plants, you need to use a lawn mower with a sharp knife. The length of the threads that can be tucked into the trimmer can range from 10 to 100 meters.

How to wind the line onto the trimmer spool

Product spools can have different yarn feeding systems. It can be manual, semi-automatic or automatic feeding. Depending on this, it is necessary to wind the fishing line. So how do you thread the bobbin? To begin with, the cap is unscrewed on the coil (see). If the thread on it is left-handed, then you need to turn it clockwise, and not as usual.

Such a thread is made so that during the operation of the product the trimmer head cannot unwind. To thread the thread, you need about 5 meters of material (see photo). It must be folded strictly in half, the center must be inserted into a specially designated place on the apparatus and wound in the direction of the arrow, which must be drawn on the coil, as in. After that, you just need to screw the cap.

A properly selected anatomical mattress is a guarantee of health and comfortable sleep. Its main task is to provide the correct support for the spine during.

It is difficult to imagine an easier and completely healthy way to heat food than cooking with an electric grill. Thanks to a unique device.