How to insert the line into a lawn mower correctly

Replacement instructions. how to insert the line

It should be noted that the reels in mowers can be different:

  • for functioning with one antenna;
  • for functioning with two antennae;
  • the line must be threaded through the through hole, which is located inside the element.

And do not confuse this part with an extension cord for a lawn mower on a reel, because despite the similar name, these are two completely different elements.

The mini chainsaw is designed for light work and people who prefer to hold the device with one hand.

This article will tell you about how much the ZIL 130 dump truck weighs and what this transport is capable of.

Read here //machinspec.com/lesozagotovitelnaya/benzopila/stanok-dlya-zatochki.html how to assemble a machine for sharpening chainsaw chains with your own hands quickly and easily.

In the first option, winding the cutting element is very simple:

  • There is a locking tab on the inside of the spool element.
  • One tendril of thread is inserted into it.
  • It is necessary to thread the nylon thread in the direction opposite to the rotation of the spool element.
  • You will need only 2 to 4 meters of fishing line. When the winding process is complete, put the small end of this cutting element outward and fix it in the groove, which is necessary for fixing the line so that it does not unwind during the operation of the mower.
  • If there is no special groove, then the end should be held by hand so that the cutting element does not unwind during further assembly of the element.
  • At the last stage, it is necessary to thread the outer end of the thread into a special hole located on the outer part of the element. The spool can then be inserted into the mower.

When the roller is working with both ends of the plastic filament, then the following steps must be taken to thread the line into the mower:

  • Inside, on the spool, you will see how many slots there are for winding (two or one). If there is only one groove, then both ends of the thread will be guided through this groove. If there are two of them, then the antennae are laid out separately. each in its own notch.
  • It is necessary to unwind from 2 to 4 meters of polyethylene thread and thread its two ends into the hole.
  • Wind both threads in the opposite direction to the rotation of the drum.
  • When all the line is wound, the ends should be fixed in the grooves or held by hand.
  • Both ends are threaded into the eyelet from the outside of the roller housing.
  • The drum is then collected and inserted into the mower.

Tips and steps for changing the line on video.

To insert line into a lawnmower that has two grooves on the spool, you must use the previous threading method for this polyethylene thread. In this case, each of the ends of the line will be wound along its own groove. All other actions are similar to the previous process.

The spool element or roller can have a completely different design from the previous two options. The line can be threaded through the eyelet, which is through and located inside the reel. In this case, you do not need to disassemble the roller drum and manually wind the polyethylene thread.

The polyethylene thread is threaded through the hole and rotated by pressing a special button. This button is located on the body and is intended for the operation of the technique, so that it is possible to release the line as it wears out.

Do not worry that the polyethylene thread will wind in the wrong direction, since in this design it can only spin in one direction.

Which line to choose to refuel the lawn mower

The thickness of the polyethylene thread depends on the model of equipment and varies from 1.2 to 4 mm. She may be:

  • with a round cross-section. this is the most durable material for mowing grassy plants;
  • with a curly section. used for mowing soft plants;
  • twisted. used for thin grass;
  • professional type, not suitable for all models of equipment.

To change the line on a lawn mower, you need to purchase a cutting thread that will be ideal for the type of mower.

You can soak the thread in a bowl of water for a few minutes to increase elasticity and strength.

How to fill a line in a lawn mower: how to change and load into a reel, how to change and how much to wind into a trimmer

When spring comes, people often spend their free time at their summer cottage. They try to rid their area of ​​problems such as weeds and grass with the onset of warm days. It is difficult to do this manually, especially if the area is very large, so a lawn mower will help. Thanks to this technique, you can trim the grass and remove weeds. it is a suitable device for mowing unnecessary plants near the fence, at home, between rows in the garden on a flower bed, and so on. Read about how to choose the right mower for your needs here. The cutting element in this device is a fishing line (strong polyethylene thread), which is wound on a special element. a spool. But over time, the line wears out and it becomes necessary to replace it. The article will talk about how to fill the line in a lawn mower.

Safety engineering

To quickly and safely change the line on the reel of the mower, it is necessary to observe safety precautions. Before removing the reel to wind the line around the mower, the technician must be disconnected from the power supply (if the mower is powered by electricity). Here I would like to mention the reliability rating of electric lawn mowers, which will help you choose a safe helper.

Another important safety rule that must be observed is pressing the lock button. You can find out its location on the vehicle body using the operating manual. For example, you can find the operating instructions for the manual petrol lawn mower here.

Do not forget that the cutting element needs to be adjusted. There is an adjustment button on the body of the unit. If the process does not start automatically and the thread tension has been released, then the button is clamped, and the fishing line is pulled out of the spool with force.

Remember that changing your mower’s line is an important and responsible process. It is necessary to carry out everything in stages, and only special polyethylene fishing line should be inserted into the spool. An iron cable, some high quality wire, or even a reinforced fishing line will not work here.

Watch the video instruction.

Line arrangement in the mower

The device of the element on which the nylon thread is wound is very simple. This element is called a coil. It has two “tracks”. the upper and the lower. Between these tracks there is a special partition with a recess. A fishing line is wound on these tracks. It must first be pulled through the recess.

In order to be able to pull out the coil without obstacles, it is necessary to unscrew the special button, which is located on the mower body.

Features of replacing fishing line on video.

If you have a summer cottage or a large plot of land near your individual house or cottage, then for the convenience of cleaning grass and weeds, you must use a lawn mower. In case you are thinking of choosing an electric lawn mower or a gasoline one, then click here and you will find comparative characteristics of different models.

Over time, the line on the mower wears out and needs to be replaced. you can do this yourself. The choice of this polyethylene thread is necessary depending on the model of the mower. It is also worth keeping an eye on the rest of the unit’s details, here, for example, you will find information about Craftsman lawn mower knives, which also wear out and can lead to irreversible consequences.

The device of the reel into which the fishing line is inserted is very simple. But it differs depending on whether the coil is operating with one or two tendrils of thread. It is important to observe safety precautions when changing the line in the reel.

How long should the trimmer line be??

For one threading of the line into the bobbin, a length of 2 to 4 m is required. it all depends on its thickness and the manufacturer’s recommendations. If you wind more, the movement of the line will be difficult, and in the process of work, you may have problems pulling out new ends.

How to replace the line with a disc?

Replacing the fishing line with a disc

insert, line, lawn, mower, correctly
  • block the shaft and remove the coil by turning it clockwise;
  • put the knife on the sleeve;
  • install the fixing cap and tighten the nut in a counterclockwise direction, and then tighten it with a wrench.

How To Install A Lawn Mower Blade Properly. Video

How to remove the line from the trimmer?

If a semi-automatic line release is used in the trimmer, then line feed is possible in two ways:. with the engine running, lightly press the button located on the reel, on the ground;. with the engine off, press the reel button and at the same time pull the “mustache” of the line, the line comes out.

Why the line won’t come out of the trimmer spool?

The cord does not feed, the reel does not spin

But if it does not come out, then the reasons may be the following: the line in the reel is incorrectly wound, because of which the latter does not spin; the cord is wound unevenly, and the thread can get stuck between the turns (the thread should be wound neatly, turn to turn, without distortions);

How to properly thread the line into the trimmer spool?

How to wind the line onto the trimmer spool

  • Fold the line in half.
  • Insert the resulting loop into the groove.
  • Lay the line in the direction indicated on the element body.
  • Insert the short end into the slot on the side of the spool.
  • Secure the long end in the opposite groove.

How to put line in a lawn mower?

How to properly install the reel on the spinning rod?

How to install a reel on a spinning rod

It is necessary to unscrew the mount and insert the reel into a special holder on the spinning rod. After that, you need to tighten the ring so that it tightens the base of the coil. It should be screwed on tightly so that the coil does not dangle.

How to thread a line into a reel semi-automatic?

In order to load the line into the “semi-automatic” spool, you need to open the spool body and load the line onto the inner spool. Threading the line into the “automatic” spool is performed without opening the spool cover. Fold a piece of line approximately 3m long in half. Insert a loop of line into the groove in the middle of the spool.

Thread head assembly

Before threading the line into the mower. it is necessary to turn off the engine and remove the plug from the mains. The head on which the thread is wound should be unscrewed in the direction indicated on the unit.

If the mower has a line winding guard, it must be removed. When removing, you can use a screwdriver to guide the thread head in the desired direction. All actions must be performed carefully so as not to damage the equipment.

How to insert new line into a lawn mower?

Be sure to turn off the engine and unplug the machine before winding the line on the reel of the lawn mower.

  • Find the lock button on the tool and, while holding it down, turn the cover. Remove the body cover, remove the spool and remove the remnants of the old line.
  • The new thread must be inserted into the receiver on the spool and trimmed so that the ends are equal.
  • Once the parts are aligned, you can wind them around the reel of the lawnmower. You need to leave the ends with a length of 10 cm.
  • One of them is inserted into the mounting holder, and the second one rolls up another half turn and is fixed in the opposite holder.
  • Then you can place the spool in the body and pull the threads out. After you have loaded the line into the mower, you can close the housing cover and secure it carefully.

How to put line in a lawn mower?

Installing line into the reel of a lawn mower is not an easy task. You will need to be careful not to damage delicate pieces of equipment, tangles, or break the thread. In order to properly fill the line in the lawn mower, it is necessary to perform all actions as written in the operating instructions.

This article provides general rules that are suitable for most units.

Thread adjustment

If the line is loose on the spool, the performance of the mower will decrease. In such cases, you can increase efficiency by adjusting the thread on the machine.

Most tools have a dedicated button for optimally winding the line around the mower’s spool. But the adjustment may not work if the thread protrudes more than 3 cm. In this case, the ends that are too long are automatically trimmed with a special blade. But if the length is less than 3 cm, the adjustment must be done manually. To do this, you need to hold down the adjustment button and pull the thread strongly towards you.

Device in the mower

In the trimmer, the element on which the string is pulled is very simple. It is called the “coil”. Usually it consists of an upper and a lower part (grooves), between which there is a partition with a recess. It is on these grooves that the fishing line should be wound. However, first it is pulled through the recess.

Before removing the coil, unscrew the special button located directly on the mower body. Remove the reel from the mower before changing the line.

It is not difficult to do this, but there are some peculiarities depending on the trimmer configuration and the coil itself.

In small electronic mowers, the motor and reel are at the bottom, and buttons are located on the sides of the reel. If you press them, you get the upper groove of the reel and the part where you need to wind the fishing line.

In bent-arm mowers that do not have a knife, the reels have special two-horned nuts. In such tools, you must hold the bobbin so that it does not move, and at the same time turn the nut clockwise. It is she who holds the entire reel, which is then easy to remove.

Straight boom mowers that can be fitted with a blade have a hole just below the reel. To remove the coil, a screwdriver is inserted into this hole, while the bobbin is fixed. After that, you need to turn the coil clockwise and remove it from the unit.

Sometimes there may be latches on the coil in the form of latches. They must be pressed to separate the parts of the coil. It is also possible that the top and bottom of the bobbin are connected by a thread. In this case, it is enough to grasp the top and bottom with your hands, and then twist in different directions until they unscrew.

How to reel?

Knowing how the reel is disassembled can speed up the line change process. It all depends on what design the coil has and how many antennae. Threading into a spool that has only one working mustache is quite easy, especially if you stick to a consistent plan.

Depending on the parameters of the reel and the length of the line set initially, it is recommended to choose a string from 2 to 5 meters.

First you need to remove the bobbin from the tool, and then open it.

One of the ends of the line must be installed in the hole inside the bobbin.

Next, the string should be wound onto the drum. over, this is done in the opposite direction from the normal rotation of the spool. Usually on the trimmers on the inside of the bobbin there is an arrow that shows in which direction to wind.

Part of the line must be pulled out and secured in a special groove located on the inside of the reel. Its purpose is to hold the winding while bringing the bobbin into working condition.

The end of the string must be passed through the hole located on the outer part of the bobbin.

At the last stage, you need to collect the parts of the bobbin and put it on the mower bar.

The installation of the line on a reel with two mustaches occurs in a slightly different way. First, you need to determine how many grooves go along the inside of the reel, on which the line is put on. There are options with one groove, and then both mustaches must be wound together. There are also models with two grooves, when each of the mustache goes separately.

For all double-whisker reels, a 2 to 3 meter string is recommended.

Lawn Striping. How To Achieve The Best Stripes In Your Lawn

Which line to choose

Before you stock up on this material for refueling in the trimmer, you need to decide on the choice. After all, the usual so-called round fishing line is far from the only existing species. How to choose the most suitable one? First you need to determine the working conditions.

Selection by type. Round line is the most common. It will fit any coil with rare exceptions. This type of consumable is suitable for cutting fresh, juicy grass. But with the mowing of the so-called dead wood, such a species may no longer cope. It is pointless to mention attempts to mow bushes with this thread.

In addition to the usual type, there are others with sharp edges. Usually they are made with an asterisk or a square. The presence of sharp edges is the main feature and key difference of these threads.

It is due to this feature that threads of these types are able to mow dry weeds. But sharp-cut threads are not without drawbacks, the main of which can be called rapid wear and strength, which is noticeably inferior to the round type.

In addition to the already mentioned types of woods, there are also interesting and common varieties. Especially among them can be noted fishing lines, inside which a metal wire is stretched. This type of thread is often used in gasoline powered tools with an engine over 1.5 horsepower.

Metal-cored threads come in both round sections and sharp edges. Regardless of the type of section, such threads are the best suited for overcoming difficult-to-cut plants. Threads of this type can easily mow not only dry grass, but even small bushes.

The wires with a wire inside compare favorably with other types of consumables for their incredible wear resistance. Unfortunately, this feature has a more than noticeable impact on the price of this type. The cost of yarns with a core is much higher than the cost of other types of yarns.

The first way to wind the line

The required amount of line has been cut off. Now you need to carefully examine the bobbin in order to understand what type it belongs to. It depends on how the line is to be wound on it.

There are two types of bobbins. In general, they differ slightly from each other. Regardless of the type, the coil is divided into two sections. upper and lower. In the first type, the dividing edge does not close into a ring and has a depression.

In the second type, it is solid, but near it there are small through holes on the sides on both sides. The method of winding the thread must be studied depending on which of the above types the coil belongs to.

  • The previously prepared six-meter segment must be bent in half. It is best not exactly in the middle, but in such a way that one half is about fifteen centimeters longer.
  • Then the place of the fold must be inserted into the recess in the dividing face. One half of the line should be at the top of the spool, the other half at the bottom.
  • Now you can start winding directly. You need to wind in the direction of the arrow on the bobbin. When winding, you need to hold the threads so that they do not intertwine and the upper half winds up in the upper part of the spool, and the lower half in the lower part. Each half should have about fifteen centimeters free from the end.
  • There are small indentations (or, in other words, grooves) in the upper edge of the bobbin for securing the consumable. The ends of the threads must be inserted into these grooves so that they are fixed against each other.
  • The final stage of threading the consumable into the tool. the ends attached to the bobbin must be threaded into the corresponding holes in the trimmer head.
  • That’s all. The winding process is complete. Now all that remains is to assemble the head into a single whole. The spring fits neatly back between the bobbin and the head. Then you need to insert the bobbin into the head and press them together.
  • It is recommended that the free ends of the thread be pulled out more. To do this, pull the ends of the consumable one by one so that they are removed from the grooves of the bobbin. You can make sure that the cutting element is removed from the retaining grooves by trying to pull the threads a little. they should freely exit through the holes in the head.
  • While pressing the bobbin down, you need to put the cover over it. The cover must be screwed to the head so that all the grooves on their bodies are aligned and the bobbin remains fixed between them.
  • And finally, the very last action. the head is screwed back into place at the bottom of the tool.

The process is complete. The line is tucked into a reel. The trimmer is ready for further work.

Line arrangement in the mower

The device of the element on which the nylon thread is wound is very simple. This element is called a coil. It has two “tracks”. the upper and the lower. Between these tracks there is a special partition with a recess. A fishing line is wound on these tracks. It must first be pulled through the recess.

In order to be able to pull out the coil without obstacles, it is necessary to unscrew the special button, which is located on the mower body.

Features of replacing fishing line on video.

How to wind the line onto the trimmer spool

At first glance, threading a line into the reel of a tool is not an easy task. But it is enough to carefully study this process. and in the future, all the necessary actions will be performed without any difficulties.

It is worth reading this guide to find out how to tuck the line into the trimmer. The step-by-step instructions below take into account the peculiarities of the coils of different types of trimmers, therefore, it is applicable to any tool.

So, the procedure is as follows.

  • The line spool is the bottom end of the trimmer. First of all, of course, you need to remove this head from the device. To do this, you need to fix the rod (or, in other words, the shaft) on which the coil is attached. It is required to fix it in such a way that it does not scroll. The easiest way to do this is by placing a kind of stupor (preferably metal) between the shaft threads through a special hole. When the shaft is fixed, the spool can be unscrewed.
  • At this stage, you have to remove the bobbin from the head, on which the fishing line is attached. To do this, you need to disassemble the head into elements. To do this, you first need to find a retainer on its body. It is located on the circumference of the product and is like a button. When the latch is found, you need to press it firmly. Keeping the latch pressed, turn the head cover clockwise. Then you need to remove the cover and remove the bobbin.
  • A tight spring is placed between the bobbin and the head. It needs to be put aside for a while so that it does not interfere with the winding process. Before proceeding with the step of winding the line, it is necessary to inspect the bobbin. If there are remnants of old fishing line on it, they must be removed. When the bobbin is cleaned, you can start preparing a new bobbin.
  • From a previously prepared skein of new fishing line, it is necessary to measure and cut off six (maximum. seven) meters. Keep the bobbin close at hand.

At this point, the key stage actually begins, which this article is devoted to.

How to choose the right line?

Nylon lines are suitable for both electric and gas powered trimmers. This consumable can be used for both hand tools and a wheeled lawnmower. It is important to choose the right line, as this directly affects both the result of the work and the service life of the unit. Of course, it is very easy to get confused in the offered assortment of lines, especially for beginners. However, there is a lot of advice from experts and those who have already tried various options.

For an electric trimmer less than 500 W, a thin line with a diameter of 1 to 1.6 mm is suitable. She will perfectly mow lawns with low grass. If the power of the tool is in the range from 0.5 to 1 kW, then it is better to give preference to a line with a diameter of 2 mm or slightly more.

This will be enough to cut thin grass or overgrown weeds, but not too thick.

For petrol trimmers and lawn mowers, line less than 3 mm must not be taken. This thickness will allow you to easily cope with any weeds, dry stems, dense grass. Diameter over 4 mm is only suitable for high power lawn mowers. It turns out that thick line is necessary for powerful technique. It is not recommended for use with low power trimmers, otherwise it will work poorly, constantly winding around the reel and creating additional load on the engine.

Typically, a standard package contains up to 15 meters of line. However, to replace the string on a reel, a length of about 7 meters is sufficient. It also happens that the line is produced in bays of 250-500 meters. When choosing a string, it is imperative to specify the date when it was produced. Nylon that is too old can dry out and become too brittle. If this happens, then you can soak the fishing line for a couple of hours in water, but it will not be completely the same.

When choosing, an important parameter is the section of the string, which can be of several types.

The round section is versatile. It is used for mowing grass of medium thickness and density. May make excessive noise during operation, but not used too quickly.

A square or polygonal section is more efficient than a round one. Sharp corners cut plant stems faster and with better quality.

Ribbed, twisted and star-shaped sections are the most effective. Such a fishing line manages to mow the grass very quickly. And its main drawback is its rapid wear.

The trimmer line is made of nylon, which is durable, lightweight, low cost and durable. To make the cost of the material even cheaper, polyethylene is added to it, but then the line overheats faster. Thick strings have a graphite or steel rod. Sometimes they are reinforced, which increases strength and service life.

It is worth noting that for two-piece strings are higher than for standard nylon strings.

In single flute model

The line must be pulled into the hole, and its mustache must be folded together and aligned.

Then winding is performed in the opposite direction to the rotation of the bobbin on the mower. Often there is an arrow inside the spool indicating how to put the line on correctly.

The ends of the string are fixed in special grooves or simply temporarily held by hands and pulled into the hole located on the outside of the bobbin.

After that, the spool is closed and attached to the rod, after which the mower is ready to work.

How to change the line on a lawn mower: detailed instructions

In 1971, American entrepreneur George Bollas invented a lawn mower that used a line as a cutting knife. Much time has passed since then, the drive has become more powerful, a modern trimmer can easily damage the bark, so the idea itself has transformed into mowing grass around obstacles without damaging the mower cutter itself. For a neat cut around obstacles, a smaller line head can be used and is easy to change when moving from large areas to delicate mowing. However, the cutting tool itself needs to be replaced periodically. We will tell you how to disassemble the head of a lawn mower (trimmer) and wind a new line.

All About Replacing the Line on the Trimmer Head

Choosing a line for the trimmer head

There are many types of heads available to suit different types of line. The latter is also available in several diameters: from 1.0 mm to 3.2 mm. over, its cross-section is round (including with a special groove to reduce the noise level), square, twisted and in the shape of a star.

There are no clear preferences, this explains the wide variety of shapes and diameters on the market. The round shape is usually stronger, but has the worst cutting ability and also produces a characteristic sound when rotated. Therefore, sometimes an acoustic groove is made on it, however, the use of this fishing line makes sense only on battery trimmers, in cars with a gasoline engine and a network drive, the sound level of the drive itself practically drowns out the sound from the fishing line. The square has a good cutting ability, and despite the fact that such a line is less strong than a round line, on average it is consumed less. Square fishing line quite easily cuts off the growth of the same willow up to 1 cm in diameter. The star has the maximum number of cutting edges, mows the best and is consumed the fastest.

The next nuance when choosing is rigidity. The fact is that in the production of nylon, a modifier (often maleic anhydride) is added to it, which improves its strength and prevents tearing. However, modifiers are not the cheapest component, they are trying to save on it. Therefore, a seemingly good line, which remained for the winter, unexpectedly behaves in a completely different way in the spring. it breaks, stops coming out of the reel normally. There is a recommendation to soak the fishing line in water before work, but I do not see much point in this, maleic anhydride interacts with water, but if it is not enough in nylon, then there will be nothing to interact with. Therefore, it makes no sense to stock up on fishing line for a long period of time, breaking or constantly breaking fishing line, which, moreover, does not want to leave the reel itself, can significantly complicate the work.

How to properly wind the line on the trimmer spool

Many, having worked out the factory line on a recently purchased trimmer, try to wind a new one, but cannot, because they do not know how to properly wind the line on the spool (bobbin) of the trimmer. It seems that there is an instruction, but it still does not work. Let’s try in this article to deal with this issue.

So, in order to wind the line, you first need to remove the coil from the trimmer. this will be more convenient. The removal method will depend on the type of trimmer.

than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Removing the coil from the trimmer

On small electric bottom motor trimmers (when operating near the ground), the reel usually has two buttons on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When disassembling, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (on such trimmers it is not yet possible to put a knife), you need to wrap the coil body itself with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, trying not to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers, in addition to fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver crawls even deeper, and the coil will lock. Now we turn the whole coil clockwise (since the thread is left-handed) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted with a lamb. If the coil is on latches, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you also need to make sure that the spring inside is not lost.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find a fixing hole for the line on the inside of the reel, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. Having reeled the fishing line, we leave a small piece of it unwound in order to expose it outside. We fix this piece in a special groove located on the inner part of the reel and designed so that the line does not unwind at the time of collecting the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and thread the outer piece of fishing line into the existing hole, assemble and put the coil back on the trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both tendrils are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. A reel with one groove should have a through hole through which the line is threaded. We unwind 2-4 m of fishing line, thread it through this hole so that it sticks out equally on each side of the fishing line. And we simultaneously wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, fix the resulting ends in special grooves, and if they are not there, we hold them with our fingers. We pass both ends into the existing holes on the outer casing of the coil. We collect the coil and attach it to the trimmer.

If there are two grooves, fold a piece of fishing line 2-4 m long in half, insert the loop obtained at the place of the bend into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option.

There are also reels in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, without winding, are threaded completely through the holes on the outer body of the reel, collect the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Rotate the button. the fishing line itself is wound inside. At the same time, it will not work to turn it in the “wrong” direction, since it can only rotate in one direction. If you get used to it, you can wind fishing line on such a reel without even disassembling it. you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

That’s all on this issue. Happy winding!