How to line the huter trimmer

How to replace line in any trimmer

How to replace line in any trimmer
So, first unscrew the nozzle. This should be done by rotating the drum to the right. Here we have a drum with the remnants of an old fishing line in our hands. We open it. Most often, the lid is closed with latches that can be opened with a screwdriver, threading it through the holes and slightly pressing. Or you need to squeeze the latch and turn the cover in the direction of the arrow. In this case, the lid itself must be held, since reels with automatic line feed have a spring that, when straightened, can throw out all the inner parts of the drum. Gently pulling out the reel, remove the scraps of fishing line from it.

Now you need to take 5 meters of new line and fold it in half (to find the middle). In the middle part of the reel there is a notch (in some designs. a hole), for which we need to hook our fishing line. There is also an arrow on the spool showing the direction of winding. An important detail. if the reel has two compartments, then one half of the line should be wound in one direction, and the other in the other. When finishing winding, you need to leave 15-20 cm of line free. There are also two notches on the top ring of the coil, through which these free ends need to be passed. We dealt with the winding itself.

The last step in the line replacement process is to assemble the drum. First you need to install the spring and washers in their place. Then, holding the reel with one hand, with the other you need to thread the ends of the line into the corresponding holes on the sides of the nozzle. After that, install the coil in its place, tightening the line and being careful not to dislodge the spring. When all the internal elements of the nozzle take their places, you can close the drum with a lid. You just need to make some effort to ensure that the latches fall into place. Voila! The mowing head is ready for use!
When choosing a fishing line for your motor scythe (gasoline or electric), you should dwell on some points, which we will talk about in detail.

Line diameter.
Engine power determines which maximum line diameter can be used for a given braid. For example, the manufacturer of an electric trimmer with a power of up to 1 kW recommends using a line of ø2 mm, and for values ​​of about 500 W, only ø1.5 mm. Also, the manufacturer of any heavy duty curved bar trimmer recommends using a ø2mm line.
The gasoline engine is more durable than the electric one, so you can install thicker line there, which means stronger line, which allows you to cut more grass and work longer.
On grass cutters with an even bar, you can select the line according to the following simple algorithm: the diameter in millimeters corresponds to the engine volume in tens of cubic centimeters. For example, for a Husqvarna 128R lawn mower with an engine capacity of about 25 cm3, use a line of ø2.5 ± 0.2 mm. For more powerful hedge trimmers with volumes of more than 40 cm3, only the geometric dimensions of the outlet openings of the mowing head. no more than 4 mm are the limitation of the diameter of the line.
So, a thin fishing line (about 1.5 mm) cuts well cultivated lawn grass, and a thick one (for example, 3.0-3.5 mm) successfully destroys weeds and even young shrubs.

Line shape.
The simplest and cheapest to manufacture is a round line. However, the requirements of ergonomics and environmental protection limit its use. due to its physical properties, it creates an unacceptably high level of noise (which is comparable to the noise of the engine itself). This is the classic Husqvarna round line or Oregon RoundLine or Chipmaster.
To reduce the noise produced by the line, it is given a special shape. they make it spiral like Oregon DuoLine Plus (noise reduction by 15 dB) or with special transverse grooves like Husqvarna Whisper (-8 dB).
Following the school laws of physics, the “working” part of the line during the mowing process is only the end surface, not the side surface. However, to increase the “sharpness” of the line, i.e. to increase efficiency, the cross section is changed from round to faceted: star-shaped, square or square with teeth. Oregon StarLine, Nylsaw or Flexiblade.
For example, according to the calculations of experts, the Oregon Nylsaw line, due to its square profile, is 27% “sharper” than its round counterpart, which clearly affects the increase in mowing speed.

# replace # any # diameter # shape # trimmer # lawn mower # for # spool # mow # repair # lawn mower # replacement

Video How to replace the line in any trimmer of the O T V E R T K A channel: the home master’s channel

How to replace line in any trimmer

Technological progress provides us with a lot of opportunities to get rid of manual labor. This includes, among other things, mowing grass, which required a lot of physical energy when using a conventional scythe. In modern conditions, this process is much easier, because the applied technique minimizes all costs. Devices such as electric and petrol trimmers have firmly taken the place of irreplaceable assistants in gardening. Mowing grass with their help has become more fun than hard and exhausting work.

Structurally, the trimmer consists of an engine, a rod and a working body, which, depending on the vegetation being cut, is either a mowing head or a disc milling cutter. And if everything is more or less clear with the cutter, then sometimes questions arise with the nozzle. As a rule, they appear when the line ends.

How to properly wind the line on the reel? Understanding.

So, first unscrew the nozzle. This should be done by rotating the drum to the right. Here we have a drum with the remnants of an old fishing line in our hands. We open it. Most often, the lid is closed with latches that can be opened with a screwdriver, threading it through the holes and slightly pressing. Or you need to squeeze the latch and turn the cover in the direction of the arrow. In this case, the lid itself must be held, since reels with automatic line feed have a spring that, when straightened, can throw out all the inner parts of the drum. Gently pulling out the reel, remove the scraps of fishing line from it.

Now you need to take 5 meters of new line and fold it in half (to find the middle). In the middle part of the reel there is a notch (in some designs. a hole), for which we need to hook our fishing line. There is also an arrow on the spool showing the direction of winding. An important detail. if the reel has two compartments, then one half of the line should be wound in one direction, and the other in the other. When finishing winding, you need to leave 15-20 cm of line free. There are also two notches on the top ring of the coil, through which these free ends need to be passed. We dealt with the winding itself.

The last step in the line replacement process is to assemble the drum. First you need to install the spring and washers in their place. Then, holding the reel with one hand, with the other you need to thread the ends of the line into the corresponding holes on the sides of the nozzle. After that, install the coil in its place, tightening the line and being careful not to dislodge the spring. When all the internal elements of the nozzle take their places, you can close the drum with a lid. You just need to make some effort to ensure that the latches fall into place. Voila! The mowing head is ready for use!

How to thread the trimmer spool, types of line

Trimmer line

Often, people who have gardens, vegetable gardens, summer cottages, are faced with the problem of caring for their lawn, with the need to mow the grass. To do this, you need a hand braid, or an electric one. a trimmer. It is much easier and faster to work electrically, the grass is mowed due to the line, which rotates at a tremendous speed, of the order of 8000 rpm, but from time to time the line wears out and requires replacement. There are many types of it, as well as manufacturers.

The main difference between a trimmer line is its diameter. There are several types, starting from the smallest 1.6mm, then 2mm, 2.4mm, 3.2mm. The most common and commonly used 2mm. You need to select for each trimmer individually. If you do not know which diameter to choose, before buying, look in the passport for the product, the manufacturer indicates which diameter will be optimal.

Generally, the more powerful the trimmer, the larger the line diameter. For example, for a lawn mower with a sufficiently powerful engine, there is a line of 2.4 mm or more, for a low-power engine (about 500 W). 1.6 mm.
The cross-section of the fishing line can be of different types. square, round, in the form of a star with sharp edges.

The fishing line is only suitable for mowing grass, but if you need to mow old bush, you will need a lawn mower with a knife, only she can do this task.

On sale, the fishing line is most often in factory packages (10m, 15m, 100m) for a cut. The second option comes out much cheaper, about 2 times, although the quality is the same. Stihl produces quality trimmer line.

How to tuck the line into the trimmer

Many people ask this question. In fact, this task is difficult only for the first time, they picked up the coil, unscrewed the lid, on some models the thread is left-handed, for this you need to turn it clockwise, not against, as usual. The left-hand thread is made to prevent the trimmer head from unscrewing during mowing.
Approximately 5 meters of fishing line will be required to refuel, cut it off, fold it in half. mark the middle, insert the center into a special slot, then wind it in the direction of the arrow that is shown on the spool (you can see it in the photo). In this trimmer model (electric “Grinda”) the winding space is divided into 2 parts, it turns out that part of the line is wound in one half, the other in the second. Then thread the ends into the holes, twist the lid.

How to thread the line into the trimmer spool and which one is better to use for this?

Very often, those people who personally own dachas and vegetable gardens are faced with the need to care for the lawn on the site. In such cases, you simply cannot do without the usual manual braid or trimmer. The first is slowly fading into the background, and the number of people who use it is getting smaller and smaller. The trimmer works automatically and does not require a lot of effort. over, you do not need to have a special skill to use it.

Types of trimmer lines

First of all, in order not to resort to frequent replacements, it is better to use a denser line. The number of its types and manufacturing firms is simply amazing. The main parameter of the trimmer line is its diameter. It varies from 1.6 to 3.2 mm. The most common type is 2mm line. However, its selection must be made depending on the type of trimmer you have.

There are several options for the section of the line. So, it can be round, square, in the form of an asterisk with sharp edges. The last option is the most effective. However, it should only be used on powerful braids and at the same time you need to know how to thread the line into the trimmer spool. Therefore, we can conclude that the more powerful your lawn mower, the thicker the line should be.

A process such as winding a fishing line on a trimmer is not difficult, but it has its own characteristics. First, you need to choose the right fishing line, the diameter of which is prescribed in the device’s passport.

First, unscrew the spool cap. Be careful, as the thread can be left or right. The left-hand thread is necessary so that the head of the scythe does not unwind during operation.

How the trimmer works?

The principle of operation of such a device is that the grass is cut by a special fishing line installed on a fast-rotating head. The number of revolutions per minute can reach 8000. For a short time, the line becomes unusable, more precisely, it is erased. Then summer residents have a question: “How to fill the line in the trimmer coil”?

Threading the line into the trimmer

Before threading the line into the trimmer spool, measure 5 m from the skein (this is the average amount of line installed on trimmers). Then fold it in half to find the middle. The resulting center must be inserted into a special slot located on the spool. After that, wind the line in the direction of the arrow on the head.

From the above it follows that the process of replacing the fishing line itself is not difficult. Having carried out such a manipulation as winding a fishing line on a trimmer reel several times, you will bring this process to automatism. The only thing is that you need to constantly monitor the condition of the fishing line in order to avoid breaking it at the time of work on the site, when there may not be a spare coil at hand.

Now you know how to thread the line into the trimmer spool, and you can do it yourself without much effort.!

What is a trimmer?

So let’s take a look at the trimmer varieties. They are of two types:

  • Electrically powered.
  • Gas tank fed.

Fishing line or knife. perform a cutting function in this device. In turn, the nylon thread can be as follows:

  • Ordinary thread.
  • With four or five faces.
  • Intertwined (looks like a pigtail).

But a knife in a lawn mower can be:

  • Two-bladed.
  • Three-bladed.
  • Four-bladed.

According to the material of manufacture, knives are divided into:

  • Metallic.
  • Plastic.

How to replace string trimmer line

Line feed from a reel is:

  • Manual type.
  • Semi-automatic.
  • With automatic feeding.

Important! The ranking of the most bought electric lawn mowers is as follows:

  • ALKO.
  • Bosch.
  • Vitals.
  • Iron angel.
  • Daewoo
  • Stark.
  • Hyundai.
  • Centaur.
  • What is a trimmer?
  • How to choose a fishing line?
  • Removing the spool from the trimmer
  • How to wind the line on the reel of a lawn mower?

Modern power tools help to facilitate human labor several times. So, for example, thanks to the trimmer, you do not have to mow the grass by hand, and the lawn will quickly and effortlessly become well-groomed and beautiful. For some people, a trimmer can help turn tough physical work into real fun. But what to do when the main cutting material runs out? Agree, not every person will immediately understand how to properly thread the line onto the reel of a lawn mower. For each type of coil, a corresponding nylon thread is needed and the replacement rules are completely different. Today we will consider all these issues in more detail.

UNBOXING & INITIAL REVIEW OF THE CHEAPEST 5 IN 1 STRING TRIMMER, HEDGE TRIMMER AND POLE SAW ON EBAY!

How to tuck line into the trimmer reel. lawn mowers?

How to choose a fishing line?

For each trimmer power, the developers accurately calculate the nylon thread diameter and the number of blades for the corresponding knife. Otherwise, the motor of the power tool will be severely overloaded, which will lead to its breakdown. Unknowingly, an overpayment for consumables will be provided to you. That is why the choice of line for your trimmer must be treated responsibly in order to keep costs to a minimum.

At the very beginning, you need to purchase the appropriate line. It is sold in skeins up to 120 meters long, and its diameter will be indicated in the detailed instructions for your trimmer.

Here’s what to look for when choosing a line and trimming it:

  • Most often, a 2 mm conductor is used for mowing grass with a trimmer. For mowing soft and young grass, it is enough to take a thin line, the diameter of which is 1.5–1.8 mm. But on more powerful lawn mowers you need to reel thicker fishing line.
  • Do not forget to pay attention to the structure of the vein. For example, round cord is considered the most durable and copes well even with the toughest weeds. But the vein of a curly configuration is more suitable for young or twisted grass. A thread with notches along its entire length can only work with thin stems.
  • The minimum length for one threading of nylon thread into the mower spool is 2-4 meters, depending on its diameter and the manufacturer’s recommendations. For example, if you wind too much line on the bobbin, then its movement will be difficult, and in the process of mowing the grass, you will notice new ends of excess material.
  • It is advisable to buy only approved companies. which are listed in the recommendations of your mowing appliance. It must be made of high quality material and have good durability. it is good to “mow” the lawn and not wear out very quickly.

In order to increase the elasticity and strength of the cord, place the purchased thread in water for 30 minutes. Thanks to such actions, it will be difficult for you to break even the thinnest core.

Removing the spool from the trimmer

Now we will consider the issue of removing the hairpin from different types of trimmer:

  • The bottom motor powered conveyor has two buttons on the sides. With one press of two buttons, you will need to detach one part of the gas station from the other. Simultaneously with the first half, remove the inner part, on which the core is wound.

Important! When doing the described manipulations, you need to be extremely careful so that the inner spring does not accidentally fly out and rub. This small detail is a very important “link” in helping to pull the line onto the roller.

  • The body of an electric and gasoline conveyor with a bent metal rod should be wrapped around with one hand, and the other hand should be moved counterclockwise the electronic lamb. This small piece connects the reel to the trimmer bar. After removing the lamb, it is necessary to remove the entire coil, while holding the inner spring with your fingers.
  • For an electric and ashless conveyor with a straight bar, you need to find a recess under the bobbin, insert, for example, a screwdriver into it, and slowly rotate it until the tool goes deeply and the roller is fully fixed. Next, turn the coil slowly clockwise (due to the left-hand thread) and remove it from the conveyor. Then you will need to disassemble the bobbin, assembled by snaps or twisted into a lamb. If you have a snap-on roller, then you need to push the latch on the sides to release the two parts of the part. After that, you should unscrew the lamb.

How to wind the line on the reel of a lawn mower?

Steps for a roller with one tendril:

  • To begin with, we unwind from 2 to 4 meters of nylon thread. Its length depends on the size of your coil.
  • We find a hole on the inside of the roller. which fixes the vein. We insert one end of the nylon thread into it and begin to carefully wind it in the opposite direction to the rotation of the bobbin on the device. Sometimes an arrow is drawn on the inside of the spool indicating the direction of winding the line.
  • After part of the core is already on the coil, we leave the rest of it (5-10 cm) free to expose it outside.
  • We fix the tip of the core in a special groove (groove). You will find it on the inside of the coil. If you do not have such a groove holding the cord, then you need to hold the line with your finger.
  • Now we take the outer part of the coil. we slowly pass a segment of the “hanging” core into the existing hole. The nylon thread is now wound on the bobbin.
  • We put the roller on the conveyor.

Steps for a roller with two antennae:

  • We look at the inside of the bobbin. determining the number of grooves for the core. The coil can have either one groove or two. Two antennae are wound along one hole at the same time. And a tendril is wound on a bobbin with two holes, which must travel along a separate groove. The roller with one groove has one through groove, along which the line slides.
  • We rewind 4 meters of a new nylon thread. we pass it through a double hole so that the line segments from each part are the same.
  • Now we wind the two ends of the core in a single direction, which should coincide with the direction of the pointer drawn inside the coil (arrows).
  • We leave a small part of the core for stock. We fix its ends in the grooves.
  • Slide the 2 ends of the cord into the groove on the outside of the roller.
  • We collect all the components of the roller and attach it to the trimmer bar.

Important! If the conveyor has two grooves, then you need to fold the section of the core in half, and insert the loop obtained at the bend into the groove that is located between the two grooves. After that, both cuts of the line should be wound simultaneously, each in its own “way”. All further actions should be done in the same way as the above instructions.

Actions for a roller with a core threaded through a double-sided hole located on the inside:

  • We thread the ends of the new nylon thread through the hole on the outside of the roller without winding.
  • We collect the reel and press the button for further release of the core as it gradually wears out. When you rotate this button, the line itself winds inside the bobbin.

Important! If you do such winding often, then you can wind the nylon thread without disassembling the drum. To do this, you just need to combine the double-sided groove of the inner part with the grooves of the inner roller body, and then thread the same fishing line through them.

As you can see, it is quite possible to wind the core on the trimmer coil yourself. The winding technique depends on the type of your lawn mower and on the design of the reel itself. Below we offer you a video that will help you better understand the whole process and perform high-quality line refueling in your device.

How to tuck line into the trimmer: a few simple tips

Thanks to modern power tools, a person is given a lot of opportunities to reduce manual labor. These innovations include the trimmer, which greatly facilitates the process of mowing and lawn care. This device reduces the time for gardening work, turning difficult physical work into entertainment. The trimmer uses a fishing line as a cutting tool. It stretches strongly and thus mows grass of almost any height. It is quite easy to operate a power tool, but the problem arises when the cutting material runs out. Not everyone will immediately figure out how to tuck the line into the trimmer. Although this is a simple operation, it is not always clear to a person who is faced with this task for the first time how to properly wind it on a reel. over, the instructions do not contain information on how to choose and replace the trimmer line.

How to quickly and correctly tuck the line into the trimmer?

Once you figure out how to change the cutting material, further use and maintenance of the trimmer will be greatly simplified. To wind the trimmer line, several operations should be performed, namely:

line, huter, trimmer
  • Unscrew the nozzle by rotating the drum to the right. You will have a head with the remnants of an old thread in your hands. Open it with a screwdriver, or wring out the latch and turn the cover in the direction of the arrow. This operation should be carried out carefully, since there is a spring inside, which, straightening, can throw out all the internal parts of the drum. To change the line in the trimmer, you need to take out the spool and remove the rest of the material.
  • Take 5 meters of new thread and fold it in half. There is a hole in the middle of the spool where you need to insert the material. There is also an arrow indicating the direction to reel in the trimmer line. It is important to consider some points. If there are two holes in the spool, then half of the trimmer line should be tucked in one direction and the other in the opposite direction. When finishing inserting the material, it is better to leave 15-20 cm free.
  • Assemble the drum, reinstall the spring and washers. Then, while holding the spool, thread the ends of the line into the holes on the sides of the nozzle. Then put the head in place, pulling on the cutting material.

What is a trimmer?

This equipment is based on the following elements:

  • a motor whose main function is to rotate the cutting head at the end of the rod;
  • directly the head, consisting of a coil, on which either a fishing line or a knife can be wound;
  • knives or fishing line rotating at high speed, which are the main cutting part of the device, how to load the fishing line into the trimmer will go a little further.

An electric device is inferior in its power to a gasoline one, so it is ideal for working on a standard plot of land that is adjacent to a house with source of electrical energy. The main positive aspects of such equipment are the absence of noise during operation, light weight, ease of use and, of course, environmental friendliness.

As for gasoline trimmers, such equipment, of course, is more mobile, so it can be safely transported from place to place and get rid of annoying vegetation in any area. There is no need to use electricity here, which has a positive effect on the functionality of such an apparatus. the cutting attachments can be changed, working with weeds of various types.

One of the most common attachments is the fishing line, so you should dwell on this element in more detail.

How to tuck the line into the trimmer?

Any machine for mowing vegetation is necessarily equipped with a spool, which, in turn, may differ in different models with a filament feed system (automatic, semi-automatic and manual). It is from this parameter that it is worth starting from before deciding how to fill the line into the trimmer.

In order to tuck the line into the trimmer, you need to take at least 5 meters of material, which is then folded in half. The center of the cutting element must be inserted into a specially designated place, and then the cutting attachment must be wound using the visual cues on the spool indicating the direction. At the end of all the work, the lid, of course, will need to be tightened.

Types of trimmer line

As a rule, line separation is based on different sample diameters, which can vary from 1.2 to 4 mm. The most commonly used material is a material with a thickness of 2 mm, but in no case should we forget that the choice should depend primarily on the trimmer model.

There is one main rule here: the more power the apparatus has, the thicker the line should be.

This element can also differ in the type of its section. So, it can be round (suitable for cutting plain grass) or square (for mowing soft green cover), sharp edges (tall grass) or be equipped with notches ideal for thin grass in diameter.

Do not forget that with the help of a fishing line it is allowed to mow only grass, and for other, coarser vegetation, it is imperative to use knives.

Next, you should take a closer look at the process of how to insert the line into the trimmer correctly. Indeed, it is with this procedure that many consumers often have difficulties.

How do I fit the line into the trimmer? Operating tips

The trimmer is an excellent modern device designed for mowing unnecessary grass, and its main advantage is that this technique can be used in those places where an ordinary lawn mower will simply not be able to reach due to its massiveness. It is necessary to understand in more detail what trimmers are, and how to choose the best option for a particular suburban area.

line, huter, trimmer

Line adjustment

One of the main rules when replacing and adjusting equipment is that any manipulations with the mechanism should be carried out exclusively with the engine off and the device plug disconnected from the mains.

Perhaps these tips will tell you how to tuck the line into the trimmer as correctly as possible and, accordingly, give your site a neat and aesthetic appearance. All that is required is to correctly select the cutting material required by the type and, of course, to determine the category of the most used trimmer.

How to wind the line around the trimmer cutter head or lawn mowers

Changing the line in the trimmer: 2 easy ways

A trimmer is a necessary and useful tool for a summer cottage and a private house. Many people own and actively use it, but not everyone knows how to replace the line in the trimmer, especially at first.

In this manual, we’ll walk through the entire replacement process step by step. Looking ahead, there are two ways to line the trimmer spool. There is no fundamental difference. the difference lies in the fact that in the first case one line will be refueled, folded in half, and in the second there will be two such lines.

Preparing for replacement

We disassemble the trimmer spool

For clarity, the mowing head (spool) was removed from the lawn mower. To replace the fishing line, you do not need to remove it, everything is done locally. It doesn’t take long.

We disassemble the trimmer spool. it rests on the latches. Remove the cover by pressing on the latches. If you do not have enough effort to do this with your hands, then use a screwdriver.

The spool consists of the following:

  • Spring case
  • Cover with locking latches
  • Button coil

The principle of operation is as follows. By pressing the button, the spool presses on the spring and comes out of the locking grooves in the spool cap. Holding in this state, the reel can be twisted, thereby adjusting the length of the line. When the button is released, the body spring returns the coil to its original fixed state.

Disassembled trimmer spool

On the bottom of the reel there are several holes for different diameters of the lines. They may differ from trimmer manufacturer. In some cases (like here) they are signed, in others they are not.

These holes are needed to fix the line when replacing it. After winding the fishing line on the bobbin, the ends of the latter are inserted into them. This is necessary so that the scaffold does not unwind when the coil is installed in the trimmer body. In other words, it makes it easier to change the line.

Holes for fixing the line

There are models without specifying the diameter of the consumable. Then, in order to find out what the maximum diameter of the scaffold can be used, it is tried on along the holes for removing the fishing line from the trimmer spool body (see figure below).

Fitting on the holes of the line output

The reel has two line sections separated by a baffle. They may not exist. They are needed only to delimit and facilitate the winding of the consumable.

Two sections for fishing line

First, they are determined with the required length of the loess. The latter is wound into one of the sections of the coil so that it does not go beyond its limits. In this case, 3 mm was wound, the length turned out to be about 2 meters. Those. for two sections you need a 4-meter segment. this is for the 1st method. For the second method, you need two segments of 2 meters each.

Determining the required line length

Now you need to figure out which way you need to wind it. To do this, many trimmer manufacturers apply special designations to the spools, such as in the figure below.

Special designation on the reel

If no such designations were found, then you need to pay attention to the spool body. There is necessarily an arrow that indicates the movement of the mowing head. The line is wound in the opposite direction.

Bobbin case designation

The first way

Line bent in half

The prepared segment (in this case, it is 4 meters) is bent approximately in half. one segment should be 15-20 cm longer, and inserted into a special slot located on the dividing partition.

The line is inserted into the slot

The line is wound in the direction determined earlier. This is done in an interference fit, the line is neatly distributed. In this case, you need to wind a segment that is longer in the section that is closer to the button.

There are designs that do not provide for dividing the coil into two sections. This does not change anything, the line is wound in a similar way. You just need to make sure that the segments do not overlap with each other.

The first should end that section, which is located at the bottom of the coil, i.e. the one closest to the fixing holes.

This tip fits into the corresponding hole in diameter. The line is securely fixed.

The line is securely fixed

A long segment is wound another half turn. There he is similarly fixed. In this case, the segment crosses another section of the coil.

A long segment is wound another half turn

The fixed ends of the coiled line are inserted into the holes in the trimmer spool body.

The fixed ends of the coiled line are inserted into the holes in the trimmer spool body

The coil is attached to the body. The ends of the fishing line are pulled with effort so that the fishing lines previously fixed in the holes of the reel jump out from there. It is easily identified by the characteristic sound (click).

The ends of the line pull up with effort

Button spool snaps into trimmer spool housing.

Button spool snaps into trimmer spool housing

The line was changed successfully. In this case, you need to put it back on the trimmer and you can start mowing the grass.

It should be repeated, there is no need to remove the spool from the trimmer. this was done for clarity of the process of replacing the fishing line. You can disassemble the spool in place, wind it on the spool and put it back.

Line replacement completed successfully

Tips so that they do not hit the trimmer cover can and should be trimmed.

How to wind the line around the trimmer cutter head or lawn mowers

Changing the line in the trimmer: 2 easy ways

Feedback from our readers is very important for us. Leave your rating in the comments with the reasoning for your choice. Your opinion will be useful to other users.

Review: Huter Trimmer Head. One of the serious ambushes of Huter trimmers.

The Huter ETH-1200 Semi-Automatic Trimmer Line Head comes with a reeled round line 2mm thick and 5m long.
Head weight 320g.
The head has a spool with a fishing line and two metal holes through which the ends of this fishing line are brought out, carrying out mowing of the grass with a rapid rotation of the trimmer head.
Designed for Huter Get-1200SL Electric Trimmers.

When mowing grass, the ends of the line wear out and their length decreases.
Consequently, the cutting radius becomes smaller.
You can restore the length of the ends of the line by lightly hitting the ground with the button located in the center of the head, while the trimmer head is picking up speed.
After that, the two ends of the fishing line will be fed, the excess of which will be cut off when you rotate the trimmer knife.

Sooner or later, the line either breaks off one of the cutting ends at the root and needs to be refilled, or the line ends and a new one must be wound.

In short, it becomes necessary to remove the head cover and pull the line spool out of the body.
This is where the fun begins.
A similar situation is described in Ivan Andreevich Krylov’s fable “monkey and glasses” 🙂

The fact is that the Huter trimmer head has a unique design.
I have never seen this one from any company.
Opening it to recharge the line is not for the faint of heart.

There is no description of how to do this.
The inscription on the back of the head body in English “press to open” did not help.
Pressed, tried to turn the body in both directions.
Nothing worked.

As time passed, I certainly forgot this unique experience.
It was already inconvenient to bow to Antonina again.
I had to turn on the brain, and in detail and in detail to deal with the problem.
The Internet suggested a way to uproot the trimmer head cover.
What did not suit at all.

I understood the head device from the found video.
It turned out that the lid is held by four holders that are fastened in the sockets of the case and is fixed with a latch.
By wringing it out with an appropriate flat-blade screwdriver and turning the body clockwise, you can easily remove the cover and pull out the bobbin with the rest of the line.

Line threading is standard and is described in detail in the trimmer description.
Also not easy, but you can figure it out.

When using the head for a long time, a little earth, grass residues and all kinds of dirt are stuffed into it.
For the good of the case, I cleaned out the dirt from the body and the outside of the head.

The head is assembled easily.
It is necessary:
– tuck the ends of the line into the corresponding holes in the body:

In the photo, among other things, on the bobbin, you can see the slots for attaching fishing line sizes from 1.6 to 2.6 mm.
For Huter Get-1200S electric trimmers, a 2mm line is recommended, which is securely fixed in the 2.4mm line slots.

Further:
– align the holders with the corresponding slots in the housing cover,
– by simply pressing the back of the body with the bobbin and line inserted,
– latch the cover latch,
– turn the body counterclockwise.

I got a lot of satisfaction after I finally managed to remove the head cover 🙂
The feeling of victory over the recalcitrant and hostile Nature to you 🙂
How to tame Klodt’s horses on the Anichkov bridge in St. Petersburg.

Whether or not to buy such a trimmer head?
Only if there is a desire to wrestle with her when replacing the line.
In addition, this head weighs 15g higher than that of Patriot trimmers.
How important it is. I do not know.

Plastics are ordinary, I haven’t crumbled yet.
But, people complain about its fragility. In case of careless impacts on the ground, it can crumble.

In fact, the thread in the head is standard left M10x1.25 LH.
Accordingly, a head for a line with a diameter of 2mm can be used with a standard head with the same thread, for example, from a Patriot trimmer.

There are enough offers at different from different manufacturers on the market.
From the most democratic to completely outrageous for automatic heads.
You can choose the most suitable for you.

How to remove or tuck the line into the trimmer

In order to wind the line, it will take about 10-15 minutes. What is a trimmer coil? Plastic body with a cassette inside, on which there is a special hook for easy winding of the fishing line.

Almost all trimmer reels have a similar fastening principle, this is a central screw-button, when pressed, it becomes possible to pull out the line of the required length. The photo below shows a few examples of different trimmer spools.

The bobbins of the trimmers, the motor of which is located at the very ground, have a different attachment to the axis of rotation, they have two buttons on the spool located on the sides that need to be wrung out, otherwise the replacement of the thread is no different from other cassettes.

The principle of correct winding of the fishing line is similar in all of the above cases, therefore, for example, consider the standard version with two antennae.

To remove the spool with the fishing line, you need to unscrew the centrally located screw, but note that the thread is left there, so you will have to turn it clockwise, this was done on purpose so that during operation it does not open under the influence of centrifugal force.

Next, using a screwdriver, disassemble the head and remove the spool onto which the fishing line is directly wound.

Having measured the required length and folded in half, you need to tuck the fishing line into the spool, eventually bringing its ends opposite each other (for this there are special slots for fixing).

After that, it is necessary to assemble the head in the reverse order, threading the ends of the cord into two corresponding holes.

If you have doubts or it is not entirely clear how to load the line on the trimmer, we recommend that you look at how to properly wind the line into the lawn mower.

In this video, in detail, step by step, the instructor will open the trimmer head, measure the required amount of line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.

What types of woods are there

The most common type of line that fits almost all reel types is round cord. This is an ordinary fishing line, suitable for mowing succulent grass, but it will be much more difficult to mow dead wood with it, and even more so it will not cope with bush.

As a rule, the diameter that can be used to cut young grass does not exceed 1.6 mm. The thicker the thread, the more coarse grass it is able to overcome.

There are fishing lines with sharp edges in the form of an asterisk or a square, this option is more adapted to mowing dry grass precisely due to the existing sharp edges, but its disadvantage is greater wear and tear and it is inferior in strength to a round cord.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but it is used only on lawn mowers, since the exit of such a thread from the spool is difficult, it is used most often with discs into which segments are inserted. The disadvantage of such a product is its fragility.

Most often in gasoline trimmers with an engine with an output of more than 1.5 hp. use cords with a metal cable inside.

This thread is ideal for cutting dry grass and small bushes. The presence of a core has a positive effect on the wear resistance of this material.

The disadvantage of such a cord is its price, which is significantly higher than the listed opponents.

How to properly wind the line on the trimmer reel. Step-by-step guide VIDEO

How to wind the line onto the trimmer spool

How to choose a fishing line. length, diameter, restrictions

IMPORTANT TO REMEMBER! Do not use fishing line or metal cables for the trimmer. This replacement is ineffective and dangerous. The rope can injure not only the mower himself, but also those around him.

As for the length, you should rely on the estimated frequency of use of the trimmer. The more often, the more it costs to stock up expenses.

Information about the possible line diameter can be found on the body trimmer spools. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose the appropriate option, taking into account the characteristics of the cultivated area. The larger the diameter, the easier it is to mow tough grass.

Preparation. remove and disassemble the spool

On most electric and petrol trims, you will need to remove the spool to replace the line. The FUBAG tool lets you skip this step. To make the instruction universal, we will still consider it in detail:

Secure the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod.

Unscrew the bobbin case. In our example. strictly clockwise.

Unscrew the cover according to the direction indicated on the body.

Remove the coil for winding.

The preparatory stage has been passed. You can proceed to winding the fishing line.

Winding Algorithm

Insert the resulting loop into the groove.

line, huter, trimmer

Lay the line in the direction indicated on the element body.

Insert the short end into the slot on the side of the spool.

Secure the long end in the opposite groove.

Place the spool of coiled line into the spool body.

Pull the line out of the locking grooves.

Put on the cover and fix.

Trim the ends of the line, leaving 10 to 15 centimeters.

The replacement of the line is completed and now all that remains is to screw the bobbin onto the trimmer and you can work.

ATTENTION! Typical line problems

No wonder they say: “Forewarned is forearmed“. Knowing about possible problems and the causes of their occurrence, you can prevent them in time. We recommend to remember or leave a memo.

Problem Cause Decision
Line break Stones, branches and solid objects in the grass Avoid collision
Poor cord quality Replace with a quality analogue
Head outlet wear Complete replacement of part required
The line is unwound The spring in the coil is weakened Check spring and replace if damaged
The line is sticking Poor line quality, due to which it can melt under the influence of temperature from the heating head Reel in less line or replace with a better line

For a better understanding of the mechanism of the process of changing the line in the spool with a video guide prepared by FUBAG specialists: