How To Line The Trimmer

21st July 2020

Trimming the line into the trimmer
The line feed system from the trimmer is manual, semi-automatic and automatic. Here is an example of how to thread the line into the trimmer (Trimmer BOSCH Art 30).

In addition to the standard lawn line, my trimmer has a thick line for cutting rough weeds. It has the shape of a pigtail, i.E. Three lines are tightly intertwined. This line has its own spool.

Spare coil storage space

It is very simple to install such a fishing line into the reel. According to the internal scheme inside the reel. We insert the center of the line with a metal mount in the upper part of the reel, and draw the ends of the line along the grooves and bring it out.

Thick line

It is stored at the top of the trimmer body.

How to fill a line in a lawn mower: how to change and load into a reel, how to change and how much to wind into a trimmer

When spring comes, people often spend their free time at their summer cottage. They try to rid their area of problems such as weeds and grass with the onset of warm days. It is difficult to do this manually, especially if the area is very large, so a lawn mower will help. Thanks to this technique, you can trim the grass and remove weeds. It is a suitable device for mowing unnecessary plants near the fence, at home, between rows in the garden on a flower bed, and so on. Read about how to choose the right mower for your needs here. The cutting element in this device is a fishing line (strong polyethylene thread), which is wound on a special element. A spool. But over time, the line wears out and it becomes necessary to replace it. The article will talk about how to fill the line in a lawn mower.

Safety engineering

To quickly and safely change the line on the reel of the mower, you must observe safety precautions. Before removing the reel to wind the line around the mower, the technician must be disconnected from the power supply (if the mower is powered by electricity). Here I would like to mention the reliability rating of electric lawn mowers, which will help you choose a safe helper.

Another important a safety rule that must be observed is pressing the lock button. You can find out its location on the vehicle body using the instruction manual. For example, you can find the operating instructions for the manual petrol lawn mower here.

Do not forget that the cutting element needs to be adjusted. There is an adjustment button on the body of the unit. If the process does not start automatically and the thread tension has loosened, then the button is clamped and the fishing line is pulled out of the spool with force.

See instructions.

Replacement instructions. How to insert the line

It should be noted that the reels in mowers can be different:

For functioning with one antenna;
For functioning with two antennae;
The fishing line must be threaded through the through hole located inside the element.

And do not confuse this part with an extension cord for a lawn mower on a reel, because despite the similar name, these are two completely different elements.

This article will tell you about how much the ZIL 130 dump truck weighs and what this transport is capable of.

Read here //machinspec.com/lesozagotovitelnaya/benzopila/stanok-dlya-zatochki.html how to assemble a chain sharpener for chainsaws with your own hands quickly and easily.

In the first option, winding the cutting element is very simple:

There is a locking tab on the inside of the spool element.
One tendril of the thread is inserted into it.
It is necessary to thread the nylon thread in the direction opposite to the rotation of the spool element.
You will need only 2 to 4 meters of fishing line. When the winding process is complete, put the small end of this cutting element outward and fix it in the groove, which is necessary for fixing the line so that it does not unwind during the mower operation.
If there is no special groove, then the end should be held by hand so that the cutting element does not unwind during further assembly of the element.
At the last stage, it is necessary to thread the outer end of the thread into a special hole located on the outer part of the element. The spool can then be inserted into the mower.

When the roller is working with both ends of the plastic filament, then the following steps must be taken to thread the line into the mower:

Inside, on the spool, you will see how many recesses there are for winding (two or one). If there is only one groove, then both ends of the thread will be guided through this groove. If there are two of them, then the antennae are laid out separately.. Each in its own notch.
It is necessary to unwind from 2 to 4 meters of polyethylene thread and thread its two ends into the hole.
Wind both threads in the opposite direction to the rotation of the drum.
When all the line is wound, the ends should be fixed in the grooves or held by hand.
Both ends are threaded into an eyelet on the outside of the roller housing.
The drum is then assembled and inserted into the mower.

Tips and steps for replacing the line with

The spool element or roller may have a completely different design from the previous two options. The line can be threaded through the eyelet, which is through and located inside the spool. In this case, you do not need to disassemble the roller drum and manually wind the polyethylene thread.

The polyethylene thread is threaded through the hole and rotated by pressing a special button. This the button is located on the body and is intended for the operation of equipment, so that you can release the line as it wears out.

How do I fit the line into the trimmer?

Any machine for mowing vegetation is necessarily equipped with a spool, which, in turn, may differ in different models by the filament feeding system (automatic, semi-automatic and manual). It is from this parameter that it is worth starting from before deciding how to thread the line into the trimmer.

In order to tuck the line into the trimmer, you need to take at least 5 meters of material, which is then folded in half. The center of the cutting element must be inserted into a specially designed place, and then the cutting attachment must be wound using the visual cues on the spool indicating the direction. At the end of all the work, the lid, of course, will need to be tightened.

How do I fit the line into the trimmer? Operating tips

The trimmer is an excellent modern device designed for mowing unnecessary grass, and its main advantage is that this technique can be used in those places where an ordinary lawn mower will simply not be able to reach due to its massiveness. It is necessary to understand in more detail what trimmers are, and how to choose the best option for a particular summer cottage.

What is a trimmer?

This equipment is based on the following elements:

A motor whose main function is to rotate the cutting head at the end of the rod;
The head itself, consisting of a coil, on which either a fishing line or a knife can be wound;
Knives or fishing line rotating at high speed, which are the main cutting part of the device, how to load the fishing line into the trimmer will go a little further.

An electric device is inferior in its power to a gasoline one, so it is ideal for working on a standard plot of land that is adjacent to a house with source of electrical energy. The main positive aspects of such equipment are the absence of noise during operation, light weight, ease of use and, of course, environmental friendliness.

As for gasoline trimmers, such equipment, of course, is more mobile, so it can be safely transported from place to place and get rid of annoying vegetation in any area. There is no need to use electricity here, which has a positive effect on the functionality of such an apparatus. The cutting attachments can be changed, working with weeds of a wide variety of types.

One of the most common attachments is the fishing line, so you should dwell on this element in more detail.

How to tuck the line into the trimmer so that working with it does not get tired

Many summer residents use a trimmer. A scythe with an electric or gasoline engine to combat weeds. It is convenient when working in hard-to-reach places for a lawn mower: near fences, flower beds, houses, in a garden on narrow aisles, and can cut small branches. The main element of this miracle technique is an ordinary fishing line wound on a reel. The device is simple, but the cutting part wears out quickly and requires replacement. And the question of how to fill the line in the trimmer worries many owners of summer cottages.

Briefly about the line

Taking into account the models of the tool, the thickness of the line is 1.2-4 mm. There are such configurations:

Round. The most durable;
Curly. For soft grass;
Twisted or serrated. For thin grass;
Professional, not suitable for all instrument models.

When changing the cutting thread, you need to choose the one that suits your trimmer type. Preference should be given to specialized. Before tucking the line into the trimmer spool, it is better to soak it in water for half an hour. Then it will become more elastic and stronger.

How to quickly remove the coil from the tool

Before the thread is wound on a bobbin, it must be removed. Over, the methods of removal depend on the characteristics of the instrument. On trimmers with a motor near the ground, the reel has two side buttons, when pressed, part of the body is separated along with a device for winding the thread.

On tools with a bent rod, the lamb on the device is moved counterclockwise; having disconnected it, remove both the bobbin and the spring inside it. On trimmers with a straight bar, fix it with a screwdriver, rotate it clockwise and remove it. Then the device is disassembled either by means of latches, or by moving its parts in different directions. The spring is removed from the coil.

How do I fit the line into the trimmer?

In order for the area near the house to always look well-groomed and neat, it must be cut regularly. Fortunately, modern technology allows you to solve this problem without excessive physical effort. Electric trimmers are so easy to operate and maintain that even a teenager can use them to mow. The main thing is to figure out in advance how to fill the line with the trimmer.

How do I load the line into the trimmer?

So, our task is to properly load the line into the trimmer. Let’s take a closer look at where to start its implementation and what pitfalls can await us in the process.

Step 1. Choosing the line

Step 2. Remove the coil from the trimmer

To perform this operation, the trimmer must be disconnected from the mains and turned over with the working head up. The further course of action depends on the trimmer model and the design of the coil itself:

For small trimmers with a lower engine location, press on the keys located on the sides of the coil and remove its upper part from the head;
On trimmers with a curved bar, we clamp the coil body with one hand, while turning counterclockwise the lamb located on the body;
For trimmers with a straight bar and a gearbox, insert a screwdriver into the hole located under the coil, and then turn the coil body counterclockwise.

Step 3. Disassemble the coil

After the coil is removed from the head, it must be carefully disassembled. It is better to do this on an already mown area, since there may be a spring inside the coil, which will be quite difficult to find in tall grass. After disassembling, we will have three parts on our hands: the body (top cover), the protective casing and the coil itself.

Step 4. Measure the required amount of fishing line

Newbie mowers are usually interested in how many meters of line to wind on the trimmer reel? There are two ways to solve this issue:

Unwind a skein of line on a flat, dry place and separate half from it.
Measure 3-4 meters of line from the skein.

In any case, after the end of winding, the turns of the line should be on the body of the reel, without sliding off it. You don’t need to try to wind as much as possible, as the line will unwind poorly and break more often.

Step 5. Winding the line onto the reel

How to attach the line to the trimmer depends on the coil design. Consider the option when the reel body has one outlet for the line. In this case, the end of the line is clamped in the crevice of the coil, and then we wind the line, trying to lay the turns as tightly as possible. The direction of laying the turns should be opposite to the direction of rotation of the coil and is usually indicated on its inner part. After the end of winding on the reel, you must put on a protective cover and bring the end of the line into it.

If the reel is designed to work with two tails, then the line must be folded in half and laid in the groove in the center of the reel. Further winding will be carried out along one or two slots, depending on the coil design. The direction of winding must also be opposite to the direction of rotation of the coil. At the end of the ponytail, the line will also need to be led out into the holes on the top of the reel.

How do I fit the line into the trimmer?

How do I load the line into the trimmer?

So, our task is to properly load the line into the trimmer. Let’s take a closer look at where to start its implementation and what pitfalls can await us in the process.

Step 1. Choosing the line

Step 2. Remove the coil from the trimmer

To perform this operation, the trimmer must be disconnected from the mains and turned over with the working head up. The further course of action depends on the trimmer model and the design of the coil itself:

For small trimmers with a lower engine location, press on the keys located on the sides of the coil and remove its upper part from the head;
On trimmers with a curved bar, we clamp the coil body with one hand, while turning counterclockwise the lamb located on the body;
For trimmers with a straight bar and a gearbox, insert a screwdriver into the hole located under the coil, and then turn the coil body counterclockwise.

Step 3. Disassemble the coil

Step 4. Measure the required amount of fishing line

Newbie mowers are usually interested in how many meters of line to wind on the trimmer reel? There are two ways to solve this issue: