How to open a rogue of a trimmer for PIT grass. How to remove a coil from a trimmer for grass and extract a fishing line for a trimmer

30th November 2022

TRAMER REPAIR OF THE TRAMMER for Grace with your own hands

In this article, we will describe in detail the procedure for how to remove the coil of the trimmer for the grass. Step.by.step instructions with the attached video will help a beginner and an experienced user to independently remove the element of the system and clean it or replace it with a new. Before you remove the trimmer coil for the grass, it must be drowned out. for gasoline samples or disables power. for electrimaters. We will demonstrate one traditional dismantling scheme, but in different models of trimmers, the method of attaching the coil to the tool may vary. With your own hands, you can not only remove the old sample of the coil, but also change it to a new one, if such a need arose. So, a step.by.step script:

Disconnect the tool from the network or turn off the engine (for benzos).
Carefully remove the cap of the coil, holding a spiral spring in place.
Click on clamps symmetrically located on both sides with one hand, and the second carefully remove the lid.
We are looking for a hole in the gearbox cup located on the side or from above, and combine it with the same hole in the shaft hub.
Using a playground key or a metal rod-we spread it into the gearbox hole, excluding the possible enlarge of the shaft.
Remove the mowing bobbin on which the fishing line for the trimmer is wound.
A slightly drowned screw will be visible in the depths. It can be unscrewed by a cruciferous or slotted screwdriver.
With one hand we hold the body of the head, and the second, counterclockwise, unscrew the screw.
Light swaying. remove the mowing head. Even if it acidified a little, we make delicately more efforts and with the same swaying. we remove it. Often movements are produced at the watch arrow, but coils are also found that are unscrewed in the other direction.
The assembly takes place in the opposite sequence.

Removing the bobbin has to be removed in cases of damage, winding of the fishing line (which is undesirable and indicates an illiterate selection of gear), and also when you need to wind a new cord with a new coil or replace the cutting tackle. Buy a coil for a trimmer for grass will always be inexpensively offered by the Kosikosa store.

How to remove the head of a trimmer for grass: Basic rules

It is necessary to remove the trimmer head, adhering to the elementary rules in working with a motorcycle and an electric counterpart, and the main ones we will call:

Jam the gearbox for unscrewing the head with a special hexagon or neatly screwdriver, immersing it in a special hole. The latter can greatly clog with grass and merge with a common color, therefore. delicately clean and find it;
It is necessary to jam so that the shaft does not turn;
Especially carefully work with the dismantling of a broken or cracked coil. its elements can be everywhere;
Many users of a benzo.wrap today are looking for a “trimmer for grass to remove the head” today, and in instructive articles and videos we also make Accent on different types of threads. take into account the nuances of your tool;
For ease of work, it is practiced to turn the tool down down the engine, laying on a horizontal surface;
Shock and sharp efforts attached when removing the mowing head are inappropriate, since the plastic delicate case can be damaged;
Install a new coil or old, if it is still suitable, you need to be a cleaned tool.
The new tackle must meet the parameters of the old. Installation of another component, the characteristics of which do not meet the power of braids for grass, can negatively affect its elements and the operation of the mechanism as a whole;
We recommend working with a cleaned tool to avoid getting garbage and small particles of grass into the holes;
Blocking the gearbox by threading into the groove of the screwdriver is a mandatory procedure when installing a new coil or removing the old;
Remember the prevailing of the left thread on the gearbox of most trimmers;
Do not forget to remove the screwdriver from the groove groove at the end of the installation of the coil in place;
All fixations and removal must be carried out delicately, remembering that the coil is made of thin plastic;
It is not worth it to tighten the new coil (or the old one in its place), since after the working hours it will be impossible to remove it at the next time withdrawal. It is also not necessary to fix too easily. weigh the load laid on this node during operation and the resistance of the cutting material;
If you need to determine a knife or spool instead of a trimmer for a trimmer for grass. analog cutting tackle, then the gearbox block is also carried out, twisting is carried out according to the same scheme, but the installation itself is slightly different due to the specifics of each individual gear. Mount the knives on a trimmer for grass with a coil if the tool functionally works with different types of gear.

If you need to buy a fishing line for a trimmer for a trimmer for grass, then you can do this in the vastness of our site, and how to mount and replace it correctly. we will tell you joy in our articles.

Frequent errors

Although the winding of the fishing line is a very simple task, many newcomers can wrap a fishing line for a trimmer incorrectly. The most common errors are presented below.

Many people when measuring the thread think that 4 m is a lot. Because of this, people often measure less, and they, accordingly, do not have enough fishing line. Do not be afraid to measure a lot, because you can always cut off the excess.
In a hurry, some people do not observe the gas stations inside the coil and wind up the thread like it. This leads to the “departure” of the fishing line from the coil and can even cripple.
For winding, it is worth using only the corresponding fishing line for the trimmer. This error is most common. You need to monitor not only the thickness and volume of the fishing line, but also your type. You should not use the first fishing line for a trimmer for wrapping, which will not match the goals. For example, you do not need to use a thread on the young grass, if it is necessary to mow dry.
Do not turn on the device until complete winding and collection. Although this is obvious, some people do this in order to check if everything is done correctly.
In no case should you confuse the refueling direction, as it will overload the engine, and it will soon get out of the working condition.

Beginners are quite characteristic of mistakes, so it is necessary to observe the advice given in this article.

About how to replace a fishing line for a trimmer on a trimmer Patriot, see further.

a fishing line for a trimmer flies out

If the string flies out with kosbe, this is another evidence that the spring in the bobbin is weakened or completely lost with an inaccurate analysis of the head. As a result, the cord does not hold and pops up when rotating.

Problems with fishing line

Trimmeres users, both gasoline and electric, sometimes have problems with the cord. “Advanced” Kosilov owners can easily cope with the difficulties, realizing why this is happening, and for beginners, this is a problem that does not have a rational explanation. But in fact, everything is solved quite simply. The most common problems that happen to the fishing line are the following.

Cords of cord

If a trimmer fishing line is often torn, this can cause the following reasons:

Stones, small branches and other hard obstacles come across the grass;
The user mows the grass back to the fence, and if he is mesh, then this breaks the “antennae” even faster;
poor quality of the cord (it is recommended to purchase high.quality);
The output holes are worn out in a mowing head, which is why the fishing line for a trimmer is erased on the sharp edges of the bushings and breaks off (a complete replacement of the part will be required).

Large cord consumption

Basically, the cord quickly ends if you often knock on the ground with a semi.automatic head or press it hard. The coil unlock occurs, and the fishing line for the trimmer, lengthening, is cut off with a knife. Another reason that the cord quickly ends is the improper operation of the device with an automatic head: the user during kosbe often drops engine speed. But as we recall, the automatic head is arranged so that it is with each reduction in the revolution that a new portion of fishing line is supplied, so it is quickly consumed.

The thread does not hold

It happens that the thread is unwound if the spring weakened in the semi.automatic head. The fishing line for the trimmer is constantly extended and cut off with a knife installed on the casing, which increases its consumption. To check this, remove the casing and turn on the unit. If the fishing line for the trimmer “climbed”, then you will need to replace the spring.

a fishing line for a trimmer flies out

The reason that the cord after starting the unit is unwound is also a weakening of the spring inside the head. In addition, there are times when when the unit is turned on, a spitter head is scattered, and the spring installed in it is lost. Inexperienced users do not notice the absence of a spring and collect this node without it. Therefore, the cord does not hold, and under the influence of centrifugal force flies out.

The cord is not served, the coil does not spin

Automatic or semi.automatic head should serve a fishing line for a trimmer without stopping the unit. But if it does not come out, then the reasons may be as follows:

The fishing line for a trimmer in a coil is incorrectly wound, which is why the latter does not spin;
The cord is wound unevenly, and the thread can get stuck between the turns (the thread should be wrapped neatly, the turn to the turns, without distortions);
Too short ends of the threads come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the fishing line is not supplied for the trimmer (it is recommended to always adjust the length of the cord before starting the unit, slightly pulling it up);
The fishing line for the trimmer is sticking together (it will be considered later).

The thread sticks together

This nuisance occurs most often due to the use of poor-quality cord. When the apparatus is operating, the head of the trimmer for the grass heats up, and a poor.quality fishing line for a trimmer in it melts, gluing among themselves. Also, sintering of the threads occurs when a fishing line with a solid obstacle occurs. In this case, there is a sharp braking of the cord, after which it drags it into the head, where it bothers. Some unit owners recommend lubricating the cord with mineral oil or spray on it with a silicone spray after winding on a spul. Others advise to wrap less threads on the coil. But it is better to immediately buy a quality product, in the manufacture of which the manufacturer took into account the factor of overheating of the head, and the thread will not stick together.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the fixing technological hole located inside the spool.
The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobbin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Ryobi Weed Wacker String Replacement 40v (Ryobi Expand-It String Trimmer)

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Fishing winding

Tramoring the fishing line in a trimmer coil for grass is a relatively simple procedure, provided that you adhere to a certain algorithm of action. When you need to determine how many meters of consumables are enough, wind it on the bobbin so that the skein does not exceed the diameter of the sides. Having decided on the length of the cord, follow the following instructions:

Fold the consumable material so that one end of the fishing line is 10-15 cm longer than the other.
You need to start charging with the central side, which divides the backpack of the trimmer for the grass into 2 parts. Find a groove where the cord should be inserted. The latter is bent twice.
Determine in which direction you need to wind the fishing line for the trimmer. To do this, take a look at the bobbin on which there can be an arrow or inscription. She indicates the side of winding. If there are no designations on the coil, then look at the arrow on the mowing head. carry out windings in the opposite direction.
Wash the consumable material carefully, a round to the round. Try to adhere to maximum thread tension.
After completing the cord laying, fasten first the short end of the material. To do this, insert it into the groove on the side of the coil, which is suitable in diameter. The second end (more authentic), attach to the groove on the other side of the backpack of the trimmer for the grass.
By fixing the fishing line for the trimmer, cut its ends. Do not forget to leave allowances about 10 cm.
Install the refitted coil to the mowing head of the device. To do this, you need to insert and pull the thread alternately into the weekend of the head, then place the keyboard of the device in the skin.
By applying the required force, pull the cord from the fixing grooves and tighten the material. At the end of this action, put on the lid and fix it using the latches.

You can wound a cord for a trimmer for grass in another way, in which two segments of the material are charged instead of one. The replacement is carried out like this:

Fishing winding

open, rogue, trimmer, grass, remove, coil

Fold the consumable material so that one end of the fishing line is 10-15 cm longer than the other.
You need to start charging with the central side, which divides the backpack of the trimmer for the grass into 2 parts. Find a groove where the cord should be inserted. The latter is bent twice.
Determine in which direction you need to wind the fishing line for the trimmer. To do this, take a look at the bobbin on which there can be an arrow or inscription. She indicates the side of winding. If there are no designations on the coil, then look at the arrow on the mowing head. carry out windings in the opposite direction.
Wash the consumable material carefully, a round to the round. Try to adhere to maximum thread tension.
After completing the cord laying, fasten first the short end of the material. To do this, insert it into the groove on the side of the coil, which is suitable in diameter. The second end (more authentic), attach to the groove on the other side of the backpack of the trimmer for the grass.
By fixing the fishing line for the trimmer, cut its ends. Do not forget to leave allowances about 10 cm.
Install the refitted coil to the mowing head of the device. To do this, you need to insert and pull the thread alternately into the weekend of the head, then place the keyboard of the device in the skin.
By applying the required force, pull the cord from the fixing grooves and tighten the material. At the end of this action, put on the lid and fix it using the latches.

Step.by.step winding of fishing line on the reel

You can wound a cord for a trimmer for grass in another way, in which two segments of the material are charged instead of one. The replacement is carried out like this:

Bend one end of the cord thread in the form of a hook.
At the bottom of the bobbin there should be a hole that is designed to fix the fishing line. Insert the bent over the end of the thread there.
Wind the cord material in the direction of the arrow to the desired level, which does not exceed the diameter of the coil of the trimmer for the grass.
The same actions need to be done for the second cell of the bobbin.
Assembly of the device head is similar to the first way.

A gasoline or electric trimmer for grass is an indispensable assistant in the arsenal of a modern summer resident or owner of their own house.

Thanks to these garden devices, you can easily bake even a large personal plot. After acquiring this tool and performing several mowing, many people think about how to correct the fishing line for a trimmer to a trimmer coil for grass. For an inexperienced user, the first operation to replace it will seem problematic and laborious, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

What can be used instead of fishing line

Many users of trimmers are wondering: how to replace the cord, by default used in this kind of devices? Unsafe experiments begin to carry out, installing metal or copper wire, metal cables or strings in a mowing head, as well as a regular fishing fishing line for a trimmer. If you install a metal cable instead of fishing line, then a trimmer for grass turns into a dangerous device not only for the user, but also for others. This fact is explained by the fact that during the operation of the unit, the steel cable will be gradually shut up, its ends are gradually released, and small pieces of wire will fly in different directions at high speed. A similar one happens when using steel or copper wire, only with the difference that the torn pieces will be larger and can cause a significant injury. And if you accidentally hook your or someone’s leg, working as an unit with a steel cable (wire), then a strong and deep section of the fabrics, and in some cases, amputation of the fingers are provided with you. The manufacturer is not in vain for these purposes, nylon uses, since it is quite light and durable, and when separating he does not fly away and cannot cause injury. It is possible to use a fishing fishing line for a trimmer in a trimmer instead of a standard one, of course, but this will add unnecessary trouble, because it quickly wears out, breaks, mows slowly and does not fit for cutting hard grass. In addition, during the work, a lot of time is lost to replace the broken tool more than once. In practice, the installation of a regular fishing line is justified if the user is going to mow grass near the fence, especially if he is from a rabid grid. In this case, in order to protect the standard and sometimes expensive cord from wear, it changes to a fishing fishing line for a trimmer, which is not a pity. Usually, in order to change the cord to a fishing line for a trimmer, it must be selected the greatest thickness-2-3 mm.

Coil with one working osik

The easiest option and a simple sequence of actions:

The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the fixing technological hole located inside the spool.
The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobbin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

How to Load Trimmer Line on to a Bosch Grass Trimmer

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

After the cutting thread as a result of the work is worn out, turn off the braid and remove the lid on the mowing head. Pull out from the slot of the forest, stretching it to the desired length, and insert it again in the slot. The amount of material wound on the coil is enough for 5-10 cycles of work depending on the model of the device. When you install the lid in place, carefully look at whether the grooves were clogged where the latches are inserted, if they are clogged, then carefully clean them.

When the fishing line for the trimmer is worn out, you need to disassemble the braid head again, pull out the coil and wind up the work fishing line for the trimmer again.

Trimmer for grass is the most common unit used to cut grass and cut small shrubs. This device is distinguished by its simplicity in maintenance, simple management during operation, and even women cope with it even a small weight. It is no secret that for the high.quality performance of herbal mowing work, the correct selection of a cutting tool is required. As the latter in trimmers, special cutting nozzles (wheels, knives) or trimmer heads with fishing line inside are used. Nozzles and a fishing line for a trimmer are a consumable tool, but if the knives can be sharpened, then when spending the fishing line you need to replace it. In this article, we will tell you in the most detail how to correctly replace the fishing line for the trimmer.

Instructions with a step.by.step description how to wind the coil of a trimmer for grass and lawn mower

In order not to make a mistake with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the coil. This information is usually presented on a tip, which will not allow us to make a mistake using the appropriate equipment.

If the information on the coil about what diameter the fishing line for the trimmer can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the equipment, it remains to figure out how to charge it. There are two ways for this, but not for all they are applicable. Consider both methods in details, and already depending on what models and trimmers you use, you are determined on your own which option is suitable.

It is interesting! The principle of how to wind a fishing line for a trimmer for a tip of motorcycles is appropriate not only for autonomous benzar groups, but also for electric trimmers.

How to look for malfunctions in the mechanical part

The transmission of rotation from an electric trimmer for grass is performed in the same way as models with an internal combustion engine: an integral shaft works inside the rectangular section of the bar, and a curved cable works.

Their length, diameter and design are selected by the manufacturer for specific dimensions of the composite bar.

Features of the junction of the composite bar

It is made by an adapter with a screw clamp.

The large screw head is made to conveniently adjust the position of the mowing organ at the bottom of the bar. The rotation angle is selected individually.

It is convenient for me to expose it so that the longitudinal axis of the protective casing and the axis of the electric motor are located in the same plane.

In this place, a malfunction associated with the transfer of torque from a direct shaft to a cable may sometimes occur in this place. It is manifested by the fact that at idle engine the trimmer for grass works normally, and already under a small load, the mowing head stops rotating.

The method of its elimination was well shown by the owner of the video “Repair of the Electrimmer” Roman Shapkov. I recommend to see.

Method of attaching a mowing head and a casing

On my trimmer from below the rod, the adapter is fixed with rivets, into which the fastener bolt of the protective casing will be plunged.

The output shaft of a rotating cable has a hexagon at the end. A plastic mowing head is put on it.

From the inside, a return spring of the automatic discharge of fishing line during kosbe is inserted into it.

A spool was inserted into it. It is fastened with a fixing nut from above.

The device of a spitter head with a fishing line is quite simple.

However, all plastic parts do not have high strength, subject to wear. Their working surfaces are erased. After three seasons of work on my trimmer, the output holes of the fishing line from the mowing head expanded, the thickness of the fixing nut decreased.

It is difficult to apply protective measures to wear, and repair of these parts is easiest to fully replace the head. It is easy to buy it: you just need to know the exact dimensions of the hexagon and evaluate the new design according to the working characteristics.

The secrets of the selection of fishing line

Among the frequent malfunctions of the trimmer coil, there are cases when the fishing line for the trimmer ended or simply confused due to improper winding on the spool. It is not difficult to eliminate them.

But in practice, I met with another defect in the fishing line, which was sold on the state retail chain from Patriot LLC company. Her view in the factory packaging.

As I understand it, it is specially hidden in a sealed package: you can not touch when buying.

When I opened the packaging to install the fishing line in the spool, its plasticity immediately caught my eye, and not elasticity. It is easily bending, behaves like a soft wire: when in contact with the grass, it immediately breaks. It is impossible to mow: she managed to return to the seller.

Since then, I have been buying only that fishing line for a trimmer that can be molested in my hands and evaluate its operational properties.

I try to refuse varieties of ordinary round fishing line. I prefer a ribbed shape to them with faces: asterisk, trapezoid, square or triangle. They are better cut off the grass.

How to eliminate increased vibration

Reliably collected trimmer mechanics for grass is well balanced. It provides convenient work. However, bearings can be worn out over time, lose lubrication.

A prefabricated shaft transmitting rotation from the engine of a spool is able to touch the internal walls of the bar, creating excessive friction with heating.

Such a defect can and must be eliminated. This technology is shown by TV repairman with his video “Vibration during the operation of Elektokosa”.

Preparation. remove and disassemble the rogue

In most models of electroly and benzotrimmers, to replace the fishing line, you will need to remove the coil. Fubag tool allows you to skip this stage. For the instruction to be universal, we will still consider it in detail: 1.

Fix the shaft. Insert a stop element into the corresponding hole. They may be a thin screwdriver or a metal rod.

Unscrew the spool body. In our example. strictly in the direction clockwise.

Unscrew the lid in accordance with the direction indicated on the case.

The preparatory stage has been passed. You can go to the winding of the fishing line.

Preparation for the winding of the fishing line

Previously, before the winding process, it is necessary to remove the coil with a fishing line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three structural types of trimmers:

Such a model provides for the possibility of installing a knife. Removing the coil in such models is carried out by means of two keys drowned in the case. To install a trimmer knife, it is necessary to combine the hole of the bobin and rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the case is easy to unscrew with your hands clockwise.

Popular trimmers for the grass of 2018

Warranty production of the factory refueling of a trimmer for grass will inevitably require replacement of fishing line. Having a very approximate idea of how to fill the fishing line for a trimmer to the coil of the trimmer for the grass on their own, beginners are reluctant to take this matter. However, with some skills, the development of this simple science does not represent any difficulties, and the presented instruction below will facilitate this process as much as possible.

Knife nozzle for a trimmer for grass

Walking shopping in search of spare parts is an ungrateful thing, and I refused this thought right away. What is the point of wasting time and money if a new part lasts no longer the previous one, but only until the first meeting with some kind of piece of iron lurked in the grass. It is better to immediately replace a broken reel with a home-made nozzle with stainless steel knives (see. a photo).

The design of the nozzle is very simple. For its manufacture, it took only four details: the central sleeve, the washer and two knives-knives (see. rice.)

I made a central sleeve out of a pruning of a conventional tap pipe. To adjust its inner diameter to the diameter of the shaft, on one side of the blank made a through longitudinal section and slightly besieged with a hammer. The sleeve should sit on the shaft tightly, without backlash.

The puck of suitable sizes I managed to choose the finished. But, if there is no one, it is not difficult to cut it out with a sheet steel with a thickness of 34 mm and finalize with a file. I put on the puck on the sleeve and welded at four points. This is quite enough.

The knives-knives cut out of the sheet stainless steel 1 mm thick. The knives are attached to the puck on rivets. They must be steel. I used M4 screws as rivets. They must be blown up so that the knives are not firmly pressed to the puck, but they can turn freely. This is a very important point. If the knives are fixed hard, then they will surely bend or break at the first meeting with the stem, which will not be able to cut down the shaft of the trimmer for the grass.

The collected nozzle is put on the shaft of a trimmer for the grass and fixed with a copper copping cup of ∅3 mm. Shplint’s hole is best drilled in place.

The first tests of the trimmer for grass with a new knife nozzle confirmed its effectiveness. Knives easily “took” almost any grass. And with leisurely work, the electric motor was practically not overloaded. In a word, what is necessary!

However, we should not forget that metal knives are a more serious danger than a thin, almost weightless fishing line for a trimmer. Therefore, to mow grass around the house is desirable when there are no people or pets nearby. And, of course, it is necessary to constantly monitor the wear of the knives and the rivets attaching them.

Universal heads for motorcycle and what is better to choose

The above options make it possible to understand what type of head on a motorcycle is preferred. In the presence of finances, it is better to choose automatic models, and if the products do not allow you to buy a good branded head for a trimmer for automatic grass, then you should choose from the semiautomatic segment.

When choosing coils for your tool, you can find out that manufacturers, in addition to branded devices, produce still universal ones, that is, those that can be used in conjunction with different models of trimmers. This is convenient only in one case, if there are two or more tools for driving grass of different manufacturers.

A number of advantages of universal coils include:

Suitable for most trimmers and benzos different manufacturers
Low cost, but at the same time they do not differ in particular reliability, so a special approach is needed for their choice
Prevalence. if you find a proprietary coil for a specific model of a trimmer for grass, it is quite difficult, then there are no such problems with universal models

It is interesting!Heads are metal and plastic. Metal ones are more expensive, but devices made of good high.strength plastic are not inferior to them, and sometimes they even cost more.

Sources:

https: // Atlantknife.ru/elektroinstrumenty/kak-snyat-golovku-traimmera-elektricogo.HTML
https: // Domdetaley.ru/kak-Vytanut-lesku-iz-katuski-trimmera-Patriot/
https: // proinstrumentinfo.ru/kak-zapravit-slsku-v-katushku-trimmera-Pravilno-Video/
https: // tytdacha.ru/sadovaya-tehnika/gazonokosilki/kak-amotat-lesku-na-Trimmer/
https: // elpaso-antibar.ru/poplyarnye-stati/kak-otkryt-katushku-u-Trimmera-Kak-Pravilno-Zapravit-V-Katushku-Trimmera-Katalog-Sadovoj-Tehniki.HTML
https: // Domdetaley.ru/kak-razobrat-poluavtomatomatiuu-katusku-trimmera/
https: // Domdetaley.ru/kak-razobrat-spulu-trimmera/
https: // Skolkocom.ru/Info/Kak-Snyat-Golovku-S-Trimmera-Video
https: // technorama.ru/Dreli/kak-otkrutit-katushku-na-trimmeere.HTML

Grass Trimmer coil, grass, open, remove, rogue, trimmer