How to properly cut the skirting boards on the floor

How to cut corners: cutting ceiling and floor plinth correctly

Installing baguettes and baseboards gives the renovation a finished and neat look, but only if the trimming is done correctly and all joints converge perfectly even. For trimming different tools and methods are used to facilitate the work, but it is also important to consider many nuances, which we will tell you about today.

Installation of baguettes and baseboards is no less important stage of repair than any other. And trimming the corners here is the most difficult. It is important to choose the right tool for the job and the most appropriate way to cut.

Ceiling plinth

Ceiling moldings, also known as moldings, fillets, borders or just skirting, are mostly used for finishing joints between the wall and ceiling, although sometimes they are used to cover inner corners, make decorative frames or panels, and decorate niches and architectural elements. There are several of the most popular materials for making ceiling moldings:

Plastic (polyvinyl chloride). Wide and rigid skirting boards are easier to cut with a metal saw. If a more gentle tool is needed, a jigsaw is used.

Styrofoam (styrofoam). Very light and porous material, best cut with a sharp construction or office knife.

Wooden baguettes. Saw blades with a helical sharpening, specially designed for baguettes, are suitable for cutting. You can also use hand or electric jigsaws.

Baseboard

Modern floor skirting can hardly be called a plank that closes the gap. They are a structural component that complements the design and enhances the overall appearance. Baseboards are made of several materials:

Wooden corners can be made of solid wood or veneer. For trimming use flat or circular saws, jigsaws.

Plastic skirting boards are “dangerous” competitors to traditional wood. Easy to install and cut with an ordinary metal hacksaw.

Aluminum skirting boards. the latest word in interior design. They are usually cut with an electric saw or a hand-held metal saw.

Only on wooden skirting boards you’ll have to make a corner trim. The rest are trimmed evenly and joined with special corners.

Types of corners

Corner docking and trimming skirting differs depending on the type of angle, distinguish: internal, external and non-standard.

Internal corner, in other words, the corner of the room is less than 180 °, usually 90 °. When trimming an inside corner, the bottom of the ceiling plinth always protrudes over the top. The first thing is still necessary to measure the angle between the walls, if it is standard and equals 90°, then the strips are trimmed at an angle of 45°. Baguette, which is glued to the right side must be cut to the left, and the left plank. to the right.

Outer corner or outer corner is less common, it is more than 180 °, usually about 270 °. When working with such angles is exactly the opposite. The edge of the baseboard, which will be pressed to the ceiling, must be larger than the bottom.

Custom corners. Under such most often mean the corners with a degree greater or less than the standard of 90 ° and 270 °, as well as various kinds of roundings. Trimming in this case is carried out “by eye” or with the marking on the site. Areas with rounded corners are assembled from several small elements, each of which is adjusted in turn.

A few words about tools and materials

Floor skirting boards are now made of wood or polyvinyl chloride (PVC), simply put, plastic. Ceiling fillets have a slightly larger list:

The range of ceiling plinths is much wider than the floor direction.

  • Polyurethane. these skirting boards have good elasticity and can wrap around radial and other curved surfaces, but they need to be trimmed at precise angles in any case;
  • Foam. the easiest budget option, the price of foam baseboards is low and they are cut very easily;
  • PVC. the principle is the same as the floor baseboards, but the lineup is much wider;
  • Wooden. similar to the floor, only here there are still wide models;
  • Gypsum. with the advent of polyurethane and foam plastic, gypsum ceiling ties have receded into the background, firstly, they are heavy, and secondly, fragile. But to be fair it is worth mentioning them.

Since it is impossible to properly cut the ceiling plinth and its floor counterpart without a good tool, we will dwell on this issue a little more.

The best, almost perfect tool for trimming any skirting boards and not only that, is a trimmer saw with a pivoting frame. The high-speed disk makes smooth and precise cuts, and the bed in these units rotates to any angle. The only problem is the serious cost of the tool.

Trimmer saws are great for trimming baseboards and more.

It is considered one of the best hand tools for accurately cutting small wood is the coping saw. It’s true in principle, but I’ll tell you honestly, it’s not easy to find a really good quality saw, even with today’s range. If you do decide to buy such a tool, take a saw with a fine tooth.

The file saw is handy when working with a jigsaw.

Theoretically, foam and polyurethane can be cut with any sharp and sturdy knife. But you need a steady hand and at least a little experience in cutting foam plastic. Plus, it’s very problematic to cut wide baseboards with a knife.

Without experience, it is very difficult to make a clean cut with a hacksaw.

Personally, in the absence of a trimmer, I use only a hacksaw for metal. It is suitable for cutting absolutely any material, from Styrofoam to wood. By the way, often ask the question than to cut the plastic skirting boards for the floor, so. take a hacksaw for metal and just do not make a mistake.

For trimming baseboards, the metal hacksaw is one of the best tools.

How to cut a baseboard at 45 degrees

Choose a tool to form a corner

The most economical option is to buy a regular plastic wire cutter. It is a plastic block with eight working slots. Such a device is designed for only two operations: trimming at 45, 90 and 22.5 degrees. A 90-degree angle comes in handy when you need, for example, to cut a jack in the middle of the molding.

Some devices come with eccentric locks. They are better, because it is easier to work with it, the baseboard is clamped in a suitable position does not move during the cutting. Accordingly, the flaws, if any, are small and the angle is easy to adjust.

What to cut a plastic skirting board: a usual plastic plastic plinth

If you have repairs to do in your own home, then it’s ideal for you to get a more formidable tool. a rotating single-plane plier. It’s designed to cut at an angle of 15, 22.5, 30, 36, 45 and 90 degrees. The construction of this type of wire cutter includes 2.4 clamps. for clamping in the horizontal and vertical planes, and the limiter, which allows you to cut the workpiece to one length. The hacksaw will be built-in. If you do not understand how to cut plintus ceiling. video review below will help you.

How to cut a baseboard in a corner: a rotary plier

How to cut a ceiling plinth contains a detailed description of the rotary joint trimmer, and information on how to use this tool.

How to cut the ceiling plinthuss using a template jigsaw

Something reminiscent of a wire cutter is made by drawing the necessary corners of the cut on paper, cardboard or wood. It is necessary to draw two parallel mowing lines, find the center, and at the end set off the necessary angles using a protractor. The advantage of this method will be the fact that there is an option to defer at least any angle, including greater than 90 degrees. Naturally, before you cut the corners of the ceiling plinth, it is necessary to check the angle between the walls with an angle and measure it with a protractor.

The method of cutting the ceiling plinth with the drawn jigsaw is exactly the same, as well as with the jigsaw itself. Baseboard plinth pressed to one of the parallel lines, and then set the hacksaw at the desired angle, which is already marked, and cut off.

See also  How to Properly Dress a Disc On a Trimmer

How to cut the corner of the ceiling plinth with a wire cutter

The chisel is an ordinary carpenter’s tool that allows you to cut the workpiece at the desired angle. Almost always there is a tray of plastic, wood or metal with vertical slots for cutting at an angle of 90 ° and 45 °. There are also more complex designs of the plinth cutter. for cutting at angles of 90, 60 and 45 degrees. For more professional works, we use a plinth with a swiveling mechanism, where the hacksaw can be fixed at any angle to the workpiece.

How to cut a ceiling skirting board with a power drill. inside angle:

  • We put the skirting board on the ceiling, and measure the proper length.
  • Later, install the baseboard plinth in the jig so that the position coincided with the plinth on the ceiling.
  • The baseboard slat is preferably pressed against the far wall of the jigsaw.
  • Hold the skirting board with your left hand.
  • We choose a position of the hacksaw where the angle is 45 degrees and immediately the handle of the hacksaw is very close to the left hand.
  • Cut the workpiece without exerting too much pressure on the saw.
  • The next step is the trimming of the skirting board mate. We also set it against the far wall of the jig.
  • Press down and hold with the right hand.
  • We choose the position for the hacksaw when the angle is 45 degrees and the handle of the hacksaw is close to the right hand.
  • Cut the skirting.

Next, we dock the cut skirting boards and check the accuracy of the cut. For more accurate orientation still say that to do the inside corner you need to start cutting from the front of the skirting board. The wood skirting boards after trimming, most likely, it will be necessary to fit with a file.

How to cut a ceiling plinth by means of a power plinth. the outer corner:

  • In order not to make a mistake with the size, it is better to start with the marking of the inside corner, and then cut the outer corner. Otherwise it is possible that the strip may not be long enough.
  • You must attach the skirting board to the ceiling and measure.
  • Install the ceiling plinth trim and press it to the nearest wall.
  • Hold with your left hand and choose a 45-degree angle position for the hacksaw when the handle is close to your left hand.
  • Cutting the workpiece.
  • Install the striker to the nearest wall, hold the right hand.
  • Set the hacksaw at an angle of 45 degrees, with the handle close to the right hand.
  • We cut the workpiece and join the corner.

Trimming the workpiece with a wire cutter is suitable only if the angle between the walls is even. 90 degrees. In this case, the accuracy is not civilized enough, you will have to use other eyes.

Composition and characteristics of the material

To understand how to properly cut a baseboard, it is necessary to understand its composition. This will help you choose the right tool and cutting technology.

  • Styrofoam. The price and durability of this material is the lowest. But since we are creating a decorative ceiling decoration, the strength is not particularly needed.
  • Ceiling skirting boards made of polystyrene foam are more dense. denser than ordinary Styrofoam. Use the most common knife to cut this material.

Tip: Sharpen your knife well before using it. This will eliminate the presence of jagged edges in the cut areas.

Tip: The shallower and more frequent the saw tooth, the smoother the edges will be. You can even use a sheet for metal.

Using a regular hacksaw blade

Ways to cut plastic baseboards

Cutting a baseboard. it looks simple, but it is a responsible job. If the corners are not cut properly, they won’t junction properly, and the whole operation will be in vain, because the product won’t have a beautiful appearance anymore. there will be gaps between the two parts of the skirting board and the decorative inserts (corners, junction elements, etc.). д.).

Most often for cutting a skirting board, an ordinary metal hacksaw is used, which has fine teeth. However, it is not suitable for thin baseboards, as the product will simply tear under the influence of this tool.

Sometimes a baseboard is also cut with a metal scissor. But the method also has its disadvantages, because the product can crumple under the pressure of the blades. Less often, but still used and angle grinder. However, the line for trimmer sawing after it can be sloppy, as the tool often “tears” the soft plastic. Especially often this method is unsuccessful for beginners in the world of repair, who do not yet know how to control the work completely. So the angle grinder can be attributed to quite specific methods.

For your information! To cut a thin baseboard, you can use a sharply sharpened knife or a stationery knife. But such work requires some skill, so it is recommended to first practice on the scraps of an old plastic baseboard.

The most important thing in the procedure of cutting the baseboard is to observe the necessary geometry. The procedure is never performed “by eye”, here it is important to measure accurately and precisely. Therefore, there are other methods of cutting the baseboard.

Lack of fittings implies the use of other ways to connect the skirting boards. This is a variant with and without templates for trimming

Cutting according to a stencil

The method is recommended for cutting products intended for installation in non-standard in shape rooms with angles other than the standard 90 degrees. Stencils of the desired angle can be made from paper or thin cardboard. First, strips are cut from the rough material, which have exactly the same width as the baseboard. Then they are placed in the corner and fixed, then cut to the shape of the corner. The skirting itself is then cut at the required angle, following the obtained stencils.

Cutting a plastic baseboard by stencil

How to properly cut the corners of the ceiling plinth

Ceiling skirting boards can be made of wood, plastic, polystyrene. The latter option is the most common. It is reasonably priced, has many varieties and is easy to work with. A sharp knife is usually used to cut it.

Before you begin, you need to cut the material according to the perimeter of the room. You can pre-draw a diagram on paper, noting all the corner connections.

The technology of cutting the corners of the skirting boards

Trimming a baseboard in a jig. Trimming technology

  • The right slat is inserted into the jig from left to right. The back part, which will be attached to the ceiling, lies on the bottom.
  • Profile is pressed firmly to the trough and cut at an angle of 45 º.
  • From right to left another plank is placed and the same way is cut.
  • The corners of the cuts are joined at the fixing point and corrected with a knife (for foam plastic and plastic).

A standard room is rectangular with 90º corners. In fact, such perfect corners are quite rare and are only the dream of the installer. If you are lucky, then the procedure for cutting the corner of the edge of the plinth is as described above, it is very easy to do it with a facing.

When cutting, remember which side the baseboard will be placed on. You can use putty to create the perfect corner for wood surfaces or joints, but a good carpenter will never do that, but will simply file evenly.

Cutting an inside corner

A few recommendations

Every work has nuances, but they can not be taken as trivialities

For the trimming to go neatly and without problems, you need to pay attention to a few things

  • Correct measurements are the most important thing in any job. To mark the blanks for the inner corner, the measurement begins precisely from it.
  • Before cutting both slats for the outer corner, do not forget that they will “peek out” over it by a length equal to the width of the products.
  • Fixing the ceiling mouldings begin only after several checks have been made. When the edges of the skirting boards fit perfectly, then you can begin gluing them (fastening screws).
  • To correct the joined blanks you can use files or files. For foam plastic and both types of polystyrene foam, you need to take thin, sharp-sharpened blades.

Since any debut rarely passes without mistakes, it is recommended to start with training on scraps. Therefore, when buying, it is better to add 10-15% to the length of the products. So you can guarantee that the material will be enough not only for the preparation, but also for the entire room, even if flaws in the process do appear.

Main varieties of floor plinths

Not long ago, it was impossible to find other varieties of skirting boards on the market, except for wooden ones. These products are still popular, although they are gradually losing ground to more practical and durable products.

Wooden. It is a classic variant. The reason why such a skirting board is still in demand is the original material used in the manufacture. After all, when building eco-housing, people stop at products made of natural materials. Wood products are made from different types of wood, and therefore differ in decorative qualities and duration of operation.

Veneered. For the manufacture of the main part, various materials can be used, but only veneer of quality wood species is used as a top covering. When visually inspecting, without knowing the distinctive features, veneered skirting boards are practically indistinguishable from wooden ones.

See also  Stihl Does Not Start Candle Dry

PVC skirting boards. Every year, this kind of product becomes more and more popular, thanks to its practicality and low price. Plastic skirting boards are made with different characteristics, which helps to match the product solely to the needs of the homeowner. For example, manufacturers offer flexible versions for semi-circular walls, in addition, they are almost as good as wooden skirting boards in terms of decorative qualities.

What and how to cut a plastic skirting board: tools, methods, geometry

A skirting board is an element which gives a finishing touch to the house. The junction of the walls with the ceiling and floor must be made very accurately and beautifully. To choose the right baseboards, coordinate them with the walls, floor and ceiling, mount the corners. it is necessary to be able to.

How to choose the right tool for trimming a plastic baseboard

To work with plastic baseboards you need the most common tool, which is available to any craftsman and even many men of the household.

Hand tools

Of hand tools for work will come in handy a hacksaw for wood with a fine tooth cross-cutting, a hacksaw for metal, a hand drill, screwdrivers, sharp knives, scissors. All tools must be sharp, otherwise you can simply crush the edges of the cut. If there are no skills, you should practice on scraps of material with different tools.

Power tools

Of electric tools in the work you can use an electric jigsaw, an electric drill, an angle grinder.

How to cut a baseboard by stencil

The stencil is used when the junction of the walls and ceiling or floor is different from the usual right angle. The stencil is a strip of thick paper or thin cardboard with a width equal to the width of the baseboard. Two such strips are placed in the corner, fastened, and the line for trimmer joints is marked on them. If, after trimming, the docking goes well, without gaps and dents, then the real baseboards are trimmed according to the stencil.

How to cut a baseboard with a wire cutter

Chisel. a device similar to a groove, with which carpenters and joiners accurately saw a piece of board at a given angle. Structurally, there are two parallel walls fixed to the bottom. On the walls are made a pair of cuts. If a saw is inserted in the corresponding pair, it forms an angle with the axis of the device. A set of angles corresponds to the most commonly used in the work. 90 °, 45 °, 30 °, 60 °. If necessary, you can add more.

If the room with the standard 90 ° corners, sawing should be done at an angle of 45 °. This can be done very quickly and accurately with a power steering axe.

How to cut a corner on the ceiling plinth with and without a wirejet, the basic rules for using a wirejet, how to cut ceiling plinth from foam, PVC, how to make a wirejet with your own hands, tips and recommendations of experts. in our publication.

How to properly cut the corners of the baseboard

To dock two strips of baseboard was not gaps and overlaps, you need to perform the correct marking, neatly cut the desired piece and make a bevel.

How to cut the inside corner

Begin the fitting and installation of the skirting boards should be from the outermost inner corner. The distance to the second corner must be measured with a tape measure. With the same tape measure the second piece of baseboard. At the jointed ends of the skirting boards beveled at 45 ° should look outward.

How to file an outside corner

When filing the outer corner, the chamfers on the jointed ends of the skirting are filmed at a 45° angle, and should look inward.

If you look carefully at the various situations that arise before the master installing baseboards. and ceiling, and flooring. it turns out that this work always consists of three steps:

For marking there are several ways, and you must choose the one that is most accessible and effective in a particular situation.

Cut should be that tool, which is best suited for working with the baseboard material.

And install the skirting board in place should be conducted by the rules, which are widely tested by many craftsmen.

How to Cut a Plastic Baseboard

At the final step of arrangement of the floor places adjoining the final coating to the walls of the room are usually closed skirting. The most popular products are now made of plastic. They are not only aesthetic and versatile, and very functional. The question of how to cut a plastic skirting board, appears with at least any craftsman at home, faced with this procedure for the first time. Tools and equipment for such works are quite ordinary and fully available.

In comparison with counterparts made of wood or otherwise wood-fiberboard plastic skirting boards have a number of advantages. Their undoubted advantages include:

  • Durability and strength.
  • Waterproof. They are suitable for installation in rooms with high humidity (bathrooms, showers and toilets).
  • They do not need to be painted or other protective coatings.
  • The construction market offers a wide range of colors: from different monochrome to imitating the structure of expensive wood species. It is simple to pick up the fillets for any interior solutions of the room.
  • Easy processing and fastening to the wall.
  • Convenience with the following care. The only restriction: it is unacceptable to use abrasive cleaning agents, which of course scratch the upper decorative layer.
  • Affordable price.
  • Safe for human and animal health. What remains to do our client modern polymeric materials of this destination are made in serious compliance with sanitary norms and requirements.

There are several types of plastic skirting boards for the floor, depending on the material of the final coating:

  • Special T-profile for framing carpeted floors. To decorate such products use strips cut from the flooring itself, which are reinforced with a double-sided adhesive tape.

Plastic skirting board. Installation

  • L-shaped products designed specifically to secure linoleum to walls.
  • Universal, which are suitable for floors made of various materials (from tiles to laminate or parquet).

According to the multifunctional features of such products are:

  • With the arranged inside the trim cable-channel (one or more) for laying wires of different purposes (telephone, antenna, computer or electronic).
  • with pressed rubber strips on the sides for a snug fit to rough and convex walls.

According to geometric dimensions, the choice is also quite wide. The width of the fillet, which is usually chosen, is commensurate with the height of the ceiling of the room, you like from 40 to 150 mm. The standard length is 5 or 4,5 m. The thickness of the profile at the bottom of the design is in the time of 10 ÷ 38 mm.

When arrangement of the final framing of the floor at least any craftsman at home reasonably appear three main questions:

  • How to cut a plastic baseboard?
  • How to do it neatly and at the right angle?
  • As well as how and what to fix the cut pieces to the wall?

Saw long products into individual parts of the desired length of course with the help:

  • angle grinder (with a narrow cutting disc);
  • The electronic jigsaw;
  • hand saw (metal as it is called with small hardened teeth).

The final choice of what to cut the plastic plinth, depending on the already available in the assortment of tools, personal preferences and experience.

For reliable fixation of the skirting boards to the walls of the room are useful:

Secrets of installation of PVC plastic baseboard Overview of fittings and installation in detail

  • Peorator (with a drill of the required cross-section) as it is also called an electric drill (with an impact mode of operation);
  • A set of dowels and screws;
  • screwdriver otherwise speaking electric screwdriver (to save time and effort).

For careful sawing off the pieces at the required angle, you will have to buy a chisel (this, if it is not in the household). Without it there is no way.

Chisel for cutting plastic baseboard. a special device designed for gently sawing at a specific angle. Simple products are made of wood or plastic. According to its geometric shape, they are a section of an inverted U-shaped profile. The side walls have narrow kerfs for the hacksaw blade.

common fixtures were previously fixtures with 3 kerfs, allowing you to cut the end of the skirting at angles of 45 ° and 90 °. But the layout of modern apartments is very diverse, and it is often necessary to arrange the different corners of the rooms.

That’s why domestic manufacturers produce products with a huge number of slots, created to install the hacksaw blade at different angles.

.

  • Using a marker and ruler we draw the marking of the cutting strip.
  • Firmly press the profile to the vertical wall of the device so that the marking coincides correctly with the place of installation of the saw.
  • We saw it off carefully.

” PVC SKIRTING BOARD WITH CABLE DUCT, COMPLETE ASSEMBLY

There is an option to cut plastic skirting boards with a metal hacksaw. This tool has its own advantages: small cutting teeth and a small gap. But the low longitudinal hardness of narrow hacksaw blade can have a negative impact on the quality of the machined surface. Better to use the special curved saws (with a wider and stiffer blade). The hardened teeth can easily handle plastic.

complex constructions are the base with clamps (to fix the workpiece). The kit already includes a saw mounted on special guides. The cutting angle can be adjusted over a wide range. Base materials are metal or impact resistant plastic. However, such devices are more expensive. So, popular swiveling models from Gross or KWB with a double-sided saw (size and sharpening of teeth for different materials) according to the sizes are 2200-4700.

See also  How to Cut Foam Blocks at Home

What to cut a plastic plinth?

Choosing, what to cut a plastic plinth, give preference to the usual and rather simple in handling tool. It is a metal hacksaw familiar to all craftsmen.

However, this is not enough, because not only is it necessary to make a straight cut accurately, but also to cut corners accurately and correctly.

To qualitatively perform this operation you will need such a device as a joiner’s plier. It is with its help you can cut an angle of 45 or 90ͦ. Of course, you can use an angle grinder, but in this case the cutting line for the trimmer will be quite wide, which is not always convenient.

Choosing the right tool

Completing the repair and finishing work in the room, every specialist asks the question “what to cut the plastic skirting”. The answer depends on how important the quality of the resulting edge.

The highest quality it will be when using a hacksaw for metal. Its blade is thin and strong enough, so the cut will be thin and even. The edges will not crumble, and it will be convenient to cut the baseboard.

If the quality of the edge does not matter much, but the speed of the work is important, then many builders and finishers use an angle grinder.

The thickness of its disk is such that the line for the trimmer cut will be quite wide, but the edges will not always be able to please the owner with its quality. However, you can perform quite a large amount of work in a short amount of time with this tool.

Even use metal scissors to cut a skirting board, if you have no other tools handy. Not exactly a comfortable job, but it’s easy for a craftsman to take care of things when they’re needed.

In any case, the cutting tool must meet certain requirements, among which are:

Use one or another tool after you are sure of its effectiveness and possibility to do the job properly.

Alternative to standard types

The right tool does not leave jagged edges

After the PVC skirting is cut, the edges must not have any chips. The right tool, which will have to cut the skirting board, does not cause the appearance of cracks or significant irregularities on the edges of the edge.

The electric jigsaw is no less popular with builders, but it can only be used when working on panels. Skirting boards, whose feature is sufficiently thin walls, can not be properly cut with this device.

A sharp stroke and quite large teeth will lead to cracking of the product, making its installation impossible.

The safest and most effective after a hacksaw on metal recognized usual mounting (wallpapering) knife.

Cutting thin-walled baseboards, which are attached to the floor, with such a tool is performed quickly and easily enough.

Flooring PVC skirting boards, equipped with a cable duct, the easiest way to cut with a standard hand jigsaw. It will make a clear cut, keep edges intact and do not allow cracking trim.

Cut the trim that closes the trunking, you need to prepare the skirting board itself. When it is cut to size it is necessary to install a cover plank and only after that cut it.

The installation of the skirting board begins at the far inside corner. If the length of the wall is long, then you have to use a connecting cap, and then cut the baseboard before it reaches the edge of the wall or 0.5 cm to the next corner. Regardless of the number of corners and joints, the cut is straight, making the job much easier. For a detailed guide on how to cut and join baseboards, see this

Working with skirting boards

Often first-time craftsmen ask how to cut a ceiling plinth to form a correct inner or outer corner. Ceiling skirting boards can’t be cut precisely without a wire cutter. Any angle of cut is possible with this device.

Perform the correct trimming is possible with strict adherence to geometric shapes. The use of the chair makes it possible to get a perfectly straight and accurate cut.

The full set fixture has grooves designed to cut blanks at an angle:

To perform the operation, during which it is necessary to install the baseboard in the corner, you will need to cut the panel strictly at 45 ͦ. In this case, two pieces stacked together will give a full 90 ͦ when creating both exterior and interior corners. For more information on how to properly saw the skirting boards with the necessary angle, see this

Cutting any baseboard (ceiling or floor) is performed after determining the correct slope.

The configuration of the corner itself determines the location of the cut on the inner or outer surface of the part.

In cases where the walls in the room are uneven and there are almost no strict corners, it is not worth using a jigsaw. It is better to trim the skirting boards manually, using a regular painting (stationery) knife.

With what to trim a plastic skirting board for the floor

In the final stage of arrangement of the floor places adjoining the finish coating to the walls of the room are usually closed skirting boards. Plastic products have become the most popular lately. They are not only aesthetic and diverse, but also very functional. The question of how to cut a plastic baseboard arises with any home craftsman who encounters this procedure for the first time. Tools and equipment for such works are quite simple and quite accessible.

Advantages of plastic products

Compared with their wood or fiberboard counterparts plastic skirting boards have a number of advantages. Their undoubted advantages include:

  • Durability and strength.
  • Moisture resistance. They are suitable for installation in rooms with high humidity (bathrooms, showers and toilets).
  • They do not need to be painted or other protective coatings.
  • On the construction market is a huge selection of colors: from a variety of monochrome to imitate the structure of expensive wood species. It is easy to pick up the fillets for any interior solution of the room.
  • Easy processing and fixing to the wall.
  • Convenient for subsequent maintenance. The only restriction: do not use abrasive cleaning agents, which can scratch the upper decorative layer.
  • Affordable price.
  • Safe for human and animal health. All modern polymeric materials for this purpose are made in strict accordance with the sanitary standards and requirements.

Chisel: varieties and uses

Chisel for cutting plastic skirting boards is a special device designed to accurately cut at a certain angle. The simplest models are made of wood or plastic. According to its geometrical shape they are a section of an inverted U-shaped profile. The side walls have narrow kerfs for the hacksaw blade.

The most common devices until recently were devices with three kerfs that allow you to trim the end of the baseboard at angles of 45° and 90°. However, the layout of modern apartments is very diverse, and often there is a need to arrange different corners of the premises.

Therefore, manufacturers produce products with a large number of slots designed to fit the hacksaw blade at different angles.

.

  • With a marker and ruler we draw a marking of the cutting line.
  • Firmly press the profile to the vertical wall of the device so that the marking coincides with the place of the saw installation.
  • Carefully sawing.

It is possible to carry out the cutting of plastic baseboard with a hacksaw for metal. This tool has its own advantages: small cutting teeth and a small divide. However, the low longitudinal rigidity of a narrow hacksaw blade can have a negative effect on the quality of the surface finish. It is better to use special curved saws for this purpose (with a wider and stiffer blade). The hardened teeth can easily work on plastic.

complex constructions are the base with clamps (to fix the workpiece). The kit already includes a saw, mounted on special rails. Cutting angle can be adjusted over a wide range. Base materials are metal or impact-resistant plastic. But such devices have a higher price. So, popular swivelling models from Gross or KWB with double-sided saw (size and sharpening of teeth for different materials), depending on size, cost 2200-4700.

The use of such devices is very simple:

  • We set the necessary angle;
  • We press the fillet to the bed with the help of clamps, so that the mark was strictly under the blade of the saw;
  • sawing.

And even if you decide to make repairs only in one room, it is worth thinking about taking such a device for rent and not thinking than to cut a plastic baseboard. Ease of use, speed and quality of processing will pay off the money spent in full.

How and how to fasten

The easiest, least time-consuming and fairly reliable method of attachment. the use of universal quick-drying adhesives such as “liquid nails”. The disadvantages of this method include: