How to properly screw the line onto the grass trimmer spool

Grass trimmer head with automatic line threading

Some models on the market have a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on.

It is almost impossible to wind the line incorrectly in a grass trimmer with such a head, since the coil independently determines the position of the antennae.

The advantages of the automatic grass trimmer head include ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and high cost.

Second winding method

• A previously prepared six-meter-long segment is required to be bent exactly in the middle and cut. Thus, two segments of the same length are obtained.
• At one end of each segment, you need to make a small “hook”. To do this, it is necessary to bend a couple of centimeters from the edge and fix it for a short time so that the “hook” does not unbend.
• Then one segment is taken. The hook is inserted into the through hole at the top of the bobbin.
• Now you can proceed to the key stage. winding. The direction in which to wind is indicated by an arrow on the bobbin. It is important to make sure that the line is wound strictly within the upper part of the reel. You do not need to wind the thread to the very tip. about fifteen centimeters should remain free from the end.
• In the upper edge of the spool there are small recesses (so-called grooves) for fixing the consumable. The loose “tail” of the thread must be inserted into one of these grooves.
• The top of the coil is tucked in. Now you need to do the same procedure with the bottom. Take the second piece of thread. The “hook” is threaded through the through hole at the bottom of the bobbin.
• After that, you can start winding the fishing line (within the lower compartment). And for this segment, you also need to leave about fifteen centimeters free from the end. This remaining “tail” must be inserted into the notch opposite to the one into which the end of the first segment was inserted.

The subsequent steps for this type of coils are exactly the same as described for the previous type in paragraphs five to nine.

This is how the line in the grass trimmer spool changes. There is nothing complicated in the process. And already after several refuelings, all actions will come to automatism.

To visually study the process described above, you can turn to the Internet for help. The popular portal has many different videos showing how to wind the line on the reel of a grass trimmer.

The first way to wind the line

The required amount of line has been cut off. Now you need to carefully examine the bobbin in order to understand what type it belongs to. It depends on how the line is to be wound on it.

There are two types of bobbins. In general, they differ slightly from each other. Regardless of the type, the coil is divided into two sections. upper and lower. In the first type, the dividing edge does not close into a ring and has a depression.

In the second type, it is solid, but near it there are small through holes on the sides on both sides. The method of winding the thread must be studied depending on which of the above types the coil belongs to.

• The previously prepared six-meter segment must be bent in half. It is best not exactly in the middle, but in such a way that one half is about fifteen centimeters longer.
• Then the place of the fold must be inserted into the recess in the dividing face. One half of the line should be at the top of the reel, the other half at the bottom.
• Now you can start winding directly. You need to wind in the direction of the arrow on the bobbin. When winding, you need to keep the threads so that they do not intertwine and the upper half winds up in the upper part of the spool, and the lower half in the lower part. Each half should have about fifteen centimeters free from the end.
• There are small indentations (or, in other words, grooves) in the upper edge of the bobbin to secure the consumable. The ends of the threads must be inserted into these grooves so that they are fixed against each other.
• The final step of loading the consumables into the tool is to thread the ends attached to the bobbin into the corresponding holes in the grass trimmer head.
• That’s all. The winding process is complete. Now all that remains is to assemble the head into a single whole. The spring fits neatly back between the bobbin and the head. Then you need to insert the bobbin into the head and press them together.
• It is recommended that the free ends of the thread be pulled out more. To do this, pull the ends of the consumable one by one so that they are removed from the grooves of the bobbin. You can make sure that the cutting element is removed from the retaining grooves by trying to pull the threads a little. they should freely exit through the holes in the head.
• While pressing the bobbin down, you need to put the cover over it. The cover must be screwed to the head so that all the grooves on their bodies are aligned and the bobbin remains fixed between them.
• And finally, the very last action. the head is screwed back into place at the bottom of the tool.

The process is complete. The line is tucked into a reel. grass trimmer ready for further work.

How to change or wind the line on the grass trimmer reel: methods and nuances of winding, winding with your own hands

Any garden owner knows how quickly weeds can fill an area. A grass trimmer will help you to defeat them without undue effort. This incredibly useful device is an indispensable tool for trimming and mowing grass.

It is no secret that an ordinary lawn mower cannot be used everywhere. In contrast, the trimmer can handle even very difficult areas. This is especially true for those tools in which not a knife, but a fishing line acts as a cutting element.

a grass trimmer that mows grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, flower beds and flower beds, row spacing in a garden plot.

Such a convenient, and most importantly, effective device, like a grass trimmer, exists in several variations:

• petrol;
• rechargeable;
• electric.

As the names suggest, the types of grass trimmer are noticeably different from one another. But regardless of the type of this tool, a fishing line can be its cutting element. Of course, the line tucked into the reel of the grass trimmer is not endless. And sooner or later you will need to replace it with a new one.

DEWALT 40V MAX String Trimmer (DCST990): How to Replace Trimmer Head Spool Line

Line consumption directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the grass trimmer, the more active the line is. And, accordingly, the faster it will end. In this regard, the question arises: how to tuck the line into the reel of the grass trimmer?

Not everyone knows the answer to this question. But winding the line on a reel plays an important role in the operation of the grass trimmer. For the device to function properly, it is very important to properly wind the new line onto the reel. How to change the line on the trimmer, and will be discussed in this article.

How to wind the line correctly on the grass trimmer spool

A gasoline or electric grass trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these gardening devices, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the reel of the grass trimmer. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Winding the Line to the Grass Trimmer

Measured and accurate dismantling of the spool from the spool of the grass scythe makes it possible to go directly to the winding of the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

• Trimmer head with one working mustache;
• A bobbin with two line tendrils;
• Auto winding reel.

Thickness selection

In addition, you should pay special attention to the thickness of the consumable. For mowing young grass, a thread with a diameter of one and a half millimeters is suitable. The larger the diameter of the thread, the drier and coarser weeds it is capable of overpowering.

When choosing a fishing line by thickness, there is one “but”. It is important not only to assess the capabilities of the material, but also to take into account the features of the grass trimmer. Be sure to check the user manual that came with your tool for information on cutting element requirements.

Using the wrong thread can damage the tool. Using a thread that is too thick will overload the machine’s motor. And the use of a thread that is too thin will significantly increase the wear of the twisting mechanism.

How to replace string trimmer edger line

That is why the choice of consumables must be approached no less responsibly than filling it into the grass trimmer. When a suitable fishing line is found and purchased, you can begin to consider ways of winding it on a reel.

At first glance, threading a line into the reel of a tool is not an easy task. But it is enough to carefully study this process. and in the future, all the necessary actions will be performed without any difficulties.

Read this guide to learn how to line your grass trimmer. The step-by-step instructions below take into account the peculiarities of the spools of different types of trimmers, therefore, it is applicable to any tool.

• The line spool is the bottom edge of the grass trimmer. First of all, of course, you need to remove this head from the device. To do this, you need to fix the rod (or, in other words, the shaft) on which the coil is attached. It is required to fix it in such a way that it does not scroll. The easiest way to do this is by placing a kind of stupor (preferably metal) between the shaft threads through a special hole. When the shaft is fixed, the spool can be unscrewed.
• At this stage, you have to remove the bobbin from the head, on which the fishing line is attached. To do this, you need to disassemble the head into elements. To do this, you first need to find a retainer on its body. It is located on the circumference of the product and is like a button. When the latch is found, you need to press it firmly. Keeping the latch pressed, turn the head cover clockwise. Then you need to remove the cover and remove the bobbin.
• A tight spring is placed between the bobbin and the head. It needs to be put aside for a while so that it does not interfere with the winding process. Before proceeding with the step of winding the line, it is necessary to inspect the bobbin. If there are remnants of old fishing line on it, they must be removed. When the bobbin is cleaned, you can start preparing a new bobbin.
• From a previously prepared skein of new fishing line, it is necessary to measure and cut off six (maximum. seven) meters. Keep the bobbin close at hand.

How To Tips for Easy Restring of Weed Eater with 2 strings

At this point, the key stage actually begins, which this article is devoted to.

How to Wrap the Grass Trimmer Line on a Spool Correctly

grass trimmers for cutting grass are indispensable helpers both in large and small suburban areas. The convenience of their use is a controversial issue, since it requires certain skills and physical training from the owner. a grass trimmer is hung on the shoulder using a special belt and in a few hours of work, the hands can get pretty tired. But even in the process of preparing the unit for operation, difficulties may arise. For example, winding the line around the reel of a grass trimmer can be a real challenge. We will tell you how to avoid this.

It often happens that fishing line is much easier to find than a ready-made reel of line. And the line will cost less than a ready-to-use bobbin. However, it is important to know a few basic rules for winding the line on a reel, which will help to avoid problems with further use.

Open the spool and carefully inspect the bobbin. you should see an arrow, it will indicate the direction in which you will need to wind the line.

Pass both ends of the fishing line into different holes and stretch to the end, and then. wind the fishing line (both ends) in one direction. an arrow will point to it.

Carefully insert the ends of the line into the spool, keeping the cord coiled. Lower the bobbin into the spool and close.

A few secrets to winding your grass trimmer line onto a spool

To make the line break less during operation, wind less than the capacity of the reel itself. For example, if the coil capacity is 15 meters, you should wind 10 meters (that is, two ends of 5 meters, respectively).

When using line with a curved cross-section, remember that its diameter should be at least 0.3 mm less than the “working” diameter of the grass trimmer. Such a discount is made so that the notches of the curly line rub less and the line does not break so quickly.

You need to wind both lines at the same time (both ends), avoiding overlaps. You will have to try and learn how to properly hold the tension of the line: if you pull it, the line will overflow, if you do not pull it, it will twist. And you only need to wind the curly fishing line with gloves, otherwise you will get hurt.

Do not leave the ends too long, which is why the line often twists when cutting grass.

When mowing grass near obstacles (tree, fence, bush, fence, concrete), remember that line consumption will go much faster, since the line will cling to this obstacle. Take a bigger coil.

If it is false for you to wind it alone, ask someone for help Practice shows that four-handed winding can be much more effective.

Features of the use of trimmers

a grass trimmer that mows grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, flower beds and flower beds, row spacing in a garden plot.

Such a convenient, and most importantly, effective device, like a grass trimmer, exists in several variations:

• petrol;
• rechargeable;
• electric.

As the names suggest, the types of grass trimmer are noticeably different from one another. But regardless of the type of this tool, a fishing line can be its cutting element. Of course, the line tucked into the reel of the grass trimmer is not endless. And sooner or later you will need to replace it with a new one.

Line consumption directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the grass trimmer, the more active the line is. And, accordingly, the faster it will end. In this regard, the question arises: how to tuck the line into the reel of the grass trimmer?

Not everyone knows the answer to this question. But winding the line on a reel plays an important role in the operation of the grass trimmer. For the device to function properly, it is very important to properly wind the new line onto the reel. How to change the line on the trimmer, and will be discussed in this article.

What line is used for the grass trimmer?

There are several types of fishing line:

• Stronger. round;
• For mowing soft vegetation. curly;
• For mowing narrow grass. with notches;
• Special. matches certain types of grass trimmer.

The section of the cutting thread must match the vegetation to be cut.

If you need to change the fishing line, then you need to select specifically the type that is recommended by the manufacturer of this particular grass trimmer model, in other words, the thickness of the cutting thread should be suitable for the motor power and the size of the unit.

It is better to choose a specialized cutting thread. It is worth soaking the fishing line for a while if you plan to change it in the reel.

After soaking, it gains elasticity and becomes stronger.

The cutting thread can be made from various components. Common among them is nylon.

This material is characterized by the highest degree of wear resistance, the ability to withstand different temperatures and the highest loads.

Nylon line can be stored for a long time, it does not dry out and does not lose its strength.

Therefore, its service life can be quite long.

The reels or heads for the brushcutter have a different structure:

Now only I bite!

I caught this pike with a bite activator. No more fishing without a catch and looking for excuses for your bad luck! It’s time to change everything. The best bite activator of the year! Made in Italy.

Step-by-step instructions on how to wind the reel of the grass trimmer and lawn mower

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the reel. This information is usually presented on a tip, which will not allow you to make mistakes with the use of the appropriate equipment.

If there is information on the spool about the diameter of the line you can fill in, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the rig, it remains to figure out how to charge it. There are two ways to do this, but not all of them are applicable. We will consider both methods in detail, and depending on which models of brushcutters and trimmers you use, you decide on your own which option is suitable.

It is interesting! The principle of how to wind the line to guide brushcutters is appropriate not only for autonomous gasoline units, but also for electric trimmers.

Winding the Line to the Grass Trimmer

Measured and accurate dismantling of the spool from the spool of the grass scythe makes it possible to go directly to the winding of the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

• Trimmer head with one working mustache;
• A bobbin with two line tendrils;
• Auto winding reel.

How to catch more fish?

• One-string. In the modification of such a grass trimmer there is only one working line. This unit is used mainly for small jobs, such as trimming the grass.
• Two-stringed. They can be both automatic and automatic. Here the package includes two strings. Used such a grass trimmer for mowing and clearing areas.

Instructions for correctly winding the cutting thread onto the spool of the grass trimmer:

• First of all, you need to disassemble the head. To do this, press the latch and turn the cover to the side. Next, the spool is removed.
• Measure out the required amount of cutting thread and insert it into the slot.
• Wind the line on both sides in the direction of the arrow.
• Leave the ends 15 cm long uncoiled.
• These ends fit into opposite slots.
• Then the ends are fixed in the hole on the head.
• After that, the spool is carefully inserted into the body, for this you need to slightly press on it.
• If necessary, you can pull the remaining ends of the thread outward. To do this, first pull one end of the thread, and then the other so that they can easily pass through the slots on the head.
• Now you need to collect the grooves on the body and screw the cover.
• Then press the spool and try to twist it all the way. If you hear a click, the spool has clicked into place.
• Next, you need to pull the free ends of the thread to the end.

Method 2. how to properly put the line on the reel of the brushcutter with photo description and video

The second method differs from the first in that it is not a single piece of equipment that is charged into the coil, but segments from two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into the brushcutter is the same as with the first method, and to make sure of this, below are detailed instructions:

• There are two equal length pieces of material that you can use.
• One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be fixed
• Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
• The fishing line should be hooked onto the bracket, and wind it in observing the direction of the arrow
• The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
• Manipulations with the second end of the fishing line are carried out in the same way.
• The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the coil, the cover with the latches is installed

The above instructions on how to install a fishing line in a brushcutter will help not only correctly, but also quickly perform the replacement procedure. Assembling the grass trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to comfortably fix the tool. Video instruction is presented below.

than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Removing the coil from the grass trimmer

On small electric bottom motor trimmers (when operating near the ground), the reel usually has two buttons on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When parsing, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to wrap the coil body itself with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the grass trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, trying not to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gear at its end (on such grass trimmers, in addition to fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver crawls even deeper and the coil will lock. Now turn the whole coil clockwise (since the thread is left-hand) and remove it from the grass trimmer. Next, we disassemble the coil. It can be assembled with latches or twisted with a lamb. If the coil is on latches, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you also need to make sure that the spring inside is not lost.

How to properly wind the line around the spool of the grass trimmer

Many, having worked out the factory line on a recently purchased trimmer, try to wind a new one, but they cannot, because they do not know how to properly wind the line on the spool (bobbin) of the grass trimmer. It seems that there is an instruction, but it still does not work. Let’s try in this article to deal with this issue.

So, in order to wind the line, you first need to remove the coil from the grass trimmer. this will be more convenient. How to remove will depend on the type of grass trimmer.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to unwind 2-4 m of fishing line (depending on the size of the reel), find a fixing hole for the line on the inside of the reel, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. After winding the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inner part of the reel and designed so that the line does not unwind at the time of collecting the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and thread the outer piece of fishing line into the existing hole, assemble and put the coil back on the grass trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both antennae are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. A reel with one groove should have a through hole through which the line is threaded. We unwind 2-4 m of fishing line, thread it through this hole so that it sticks out equally on each side of the fishing line. And we simultaneously wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, fix the resulting ends in special grooves, and if they are not there, we hold them with our fingers. We pass both ends into the existing holes on the outer casing of the coil. We collect the coil and attach it to the trimmer.

If there are two grooves, fold a piece of fishing line 2-4 m long in half, insert the loop obtained at the place of the fold into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option.

There are also reels in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, without winding, are threaded completely through the holes on the outer body of the reel, collect the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Rotate the button. the fishing line itself is wound inside. At the same time, it will not work to turn it in the “wrong” direction, since it can only rotate in one direction. If you get used to it, you can wind fishing line on such a reel without even disassembling it. you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

That’s all on this issue. Happy winding!