How To Properly Wind The Line Onto The Reel Of The Mower

8th March 2021

Safety engineering

Following safety precautions will allow you to quickly and safely insert new line into the spool on the mower. It is imperative that before the replacement begins and the coil is removed, the device must be turned off, especially for electric lawn mowers. It is important to constantly remind yourself to press the special lock button. On each mower, it can be located in different places, but this must be indicated in the instruction manual.

Remember to adjust the cutting element. Otherwise, the work will be unstable and of poor quality. Most often, there is a button on the unit itself that allows you to configure this. If nothing happens when you press it, or the string has loosened its tension, then you need to hold down the button and pull the line out of the reel with effort.

Line winding is a very demanding process. It is important to follow all the steps correctly in order to tighten the line well. Materials other than special nylon strings should not be used. It is worth remembering that you cannot put a metal wire, a rod or an iron cable instead of a fishing line. This is dangerous, as the rig can very easily cut through the shoes even of coarse material and injure the wearer. Before putting on a new line, it is important to carefully read the operating instructions for the device, since some models of lawn mowers may have their own structural features, which are important to take into account when replacing.

You can find out how to replace the line on the trimmer from the video below.

Safety engineering

To quickly and safely change the line on the reel of the mower, you must observe safety precautions. Before removing the reel to wind the line around the mower, the technician must be disconnected from the power supply (if the mower is powered by electricity). Here I would like to mention the reliability rating of electric lawn mowers, which will help you choose a safe helper.

Another important safety rule that must be observed is pressing the lock button. You can find out its location on the vehicle body using the operating manual. For example, you can find the operating instructions for the manual petrol lawn mower here.

Do not forget that the cutting element needs to be adjusted. There is an adjustment button on the body of the unit. If the process does not start automatically and the thread tension has been released, then the button is clamped, and the fishing line is pulled out of the spool with force.

It must be remembered that changing the line in a lawnmower is an important process that requires responsibility. It is necessary to carry out everything in stages, and only special polyethylene fishing line should be inserted into the spool. An iron cable, some high quality wire, or even reinforced fishing line will not work here.

Watch the video instruction.

How to fill a line in a lawn mower: how to change and load into a reel, how to change and how much to wind into a trimmer

When spring comes, people often spend their free time at their summer cottage. They try to rid their area of problems such as weeds and grass with the onset of warm days. It is difficult to do this manually, especially if the area is very large, so a lawn mower will help. Thanks to this technique, you can trim the grass and remove weeds. it is a suitable device for mowing unnecessary plants near the fence, at home, between rows in the garden on a flower bed, and so on. Read about how to choose the right mower for your needs here. The cutting element in this device is a fishing line (strong polyethylene thread), which is wound on a special element. a spool. But over time, the line wears out and it becomes necessary to replace it. The article will talk about how to fill the line in a lawn mower.

How to wind line on a trimmer

You don’t need to have any special skills to reel in a gas or electric trimmer. To begin with, it is important to decide on a suitable consumable, and then choose the best method. There are two different ways to load the line into the spool of the device.

Selection by thickness

In addition, you should pay special attention to the thickness of the consumable. For mowing young grass, a thread with a diameter of one and a half millimeters is suitable. The larger the diameter of the thread, the drier and coarser weeds it is able to overcome.

When choosing a fishing line by thickness, there is one “but”. It is important not only to assess the capabilities of the material, but also to take into account the features of the trimmer. Be sure to check the user manual that came with your tool for information on cutting element requirements.

Using the wrong thread can damage the tool. Using a thread that is too thick will overload the machine’s motor. And the use of a thread that is too thin will significantly increase the wear of the twisting mechanism.

How To Load Mono Onto Your Reels

That is why it is necessary to approach the choice of consumables no less responsibly than to refuel it in the trimmer. When a suitable fishing line is found and purchased, you can begin to consider ways of winding it on a reel.

Features of the use of trimmers

A trimmer that mows grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flower beds, row spacing in a garden plot.

Such a convenient, and most importantly, effective device, like a trimmer, exists in several variations:

As the names suggest, trimmer types differ markedly from one another. But regardless of the type of this tool, a fishing line can be its cutting element. Of course, the line tucked into the trimmer reel is not endless. And sooner or later you will need to replace it with a new one.

Line consumption directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the trimmer, the more active the line is used in it. And, accordingly, the faster it will end. In this regard, the question arises: how to thread the line into the trimmer spool?

Not everyone knows the answer to this question. But the winding of the line on the reel plays an important role in the trimmer operation. For the device to function properly, it is very important to properly wind the new line onto the reel. How to change the line on the trimmer, and will be discussed in this article.

Trimmer head types for spools

The main elements of the trigger is the mowing head, which is a cylindrical body with a bobbin inserted inside. The fishing line (cord) is tucked into it. The heads differ from each other in the way of feeding and threading the cord. There are three types of heads in total:

Automatic. The line is then fed as the user reduces the engine speed. Automatic cord feeding is very convenient when there is a lot of work to be done. The disadvantage of such a head is the high thread consumption.
Semi-automatic. The use of such a head does not require the user to perform any complex manipulations. The principle of its operation is designed in such a way that the line begins to automatically lengthen while the trimmer is operating at full speed. You just need to lightly bang the head of the machine on the ground (this will remove the blocking of the line), and the cord will be pulled out of the bobbin due to centrifugal force. Then the fishing line is cut to the required length with a knife, which is located on the protective cover.
Manual. To lengthen the cord, the machine must be stopped. After that, the line will need to be pulled out manually.

Types of trimmer spools

Winding device

Many “craftsmen” come up with their own ways of winding. For example, you should consider how to complete the task at hand with a drill. To do this, you need a nail that goes almost close to the spool hole and a 7.5 mm thick circle of rubber.

The hardware is inserted in the center of the rubber and placed in the spool. The structure is clamped in a drill chuck or screwdriver. The line is fixed in the spool with a knot.

In one hand, you need to hold a spool of thread by the central hole, in the other. a drill. Winding is performed clockwise by adjusting the revolutions of the chuck. How to wind the line on the reel of a fishing rod correctly with such a device? To do this, you only need to drive the line up and down, making sure that it lays down evenly.

Determining the amount of rewinding

In the question of how to wind the line on a reel, for beginners there is a difficulty in determining the amount of winding. It can only be established experimentally. Experienced fishermen advise to reverse the order.

If there is a second reel of the same, you need to wind the fishing line on it first, and then the reel attached to it. In this case, the basic rule should be remembered: you can correctly wind the fishing line on the spinning reel only if the level of its top layer does not exceed 3 mm from the side of the spool. After that, you should rewind the thread to the main shule, already starting with the backing, which, as it should be, will be below.

If there is no second same coil, the measurement is made on the main coil, then the line is unwound and rewound on it, already starting from the winding.

What is backing?

It is usually difficult to determine how much line to spool. It is believed that a standard spool can hold one hundred meters of 0.3mm line. However, progress has stepped forward, and modern lines are becoming thinner, without losing the margin of safety.

How many meters of fishing line to wind on the reel, each angler decides for himself, depending on the fishing conditions. Therefore, it happens more and more often that the selected line is much smaller than the spool can accommodate. The resulting free space needs to be filled with something. Some people use electrical tape or nylon thread for these purposes, but this is not the best option. The adhesive on the tape that holds the bottom turns of the line peels off quickly. And the nylon thread dries for a very long time when wet.

Therefore, more and more anglers are inclined to the American method. to rewind the line in the lower layer, which is simpler and cheaper, and tie the main, higher quality to it. This turns of an inexpensive thread is called backing, in our opinion. reeling. It connects to the main strap with a self-tightening double loop, clinch or similar knot options.

Winding profiles (taper)

For different reel models, the turns of the line on the spool are applied in different ways. In quality products, the cylindrical and conical winding method is used. The line laid in profile forms a straight line. With a cylindrical winding, this line is straight, parallel to the spool, with a tapered winding. inclined.

The straight tapered shape tapers towards the front edge of the spool, the opposite one widens. Straight taper reduces line friction. Reverse styling reduces the chance of spontaneous line drop.

There is also a third type of winding. chaotic. Usually used in cheap Chinese fishing rods. And if such winding can still be tolerated using ordinary fishing line, then the use of a cord in such a reel should be abandoned. Bad casts, beard, overlaps and entanglements are guaranteed. This leads to bad fishing and can also ruin the mood of every fisherman.

How to wind a fishing line on a reel: instructions

When collecting tackle for fishing, it is periodically required to change the line on the reel. This is a fairly simple procedure. However, it has a number of nuances. The correctness of this procedure will determine whether the thread will be flat when casting or will start to get confused. If the fisherman does the wrong thing, the thread may break. This causes a lot of difficulties. To avoid such troubles, it is necessary to consider in detail how to wind the line on a reel. This technology will be discussed in detail in the article.

Storage rules on the spool

For the line to last longer, you need to properly care for it. When sending tackle for long-term storage, the line should be completely unwound and thoroughly dried, otherwise it will lose its elasticity. This is fraught with ruptures at the most inopportune moment. You can use a hair dryer to dry. When the line is completely dry, you need to wind it on a spool.

In general, you need to dry the thread after each fishing trip. Only this should not be done along the entire length, but only on an area slightly larger than the length of the long cast.

Backing spool connection

Another important point in the question of how to properly wind the line on the spool is its connection to the spool. Some fishermen do not fix the line at all, believing that it is long enough and will never fully unwind. This is the wrong approach. Having fastened the reel or the line in the spool, you can not be afraid of the breakdown of large prey or idle scrolling of the line when fishing.

Among the many different binding methods, the most common are:

Special knot resembling a clinch. It is very durable and practically unstretched.
A self-tightening knot is a special kind of loop that has some stretch. However, as a result of the tension of the line, such a knot is tightened to the stop and holds perfectly.

The choice depends on the preference of the fisherman. Both options are quite reliable. They will provide comfort while fishing.

Hand winding precautions

Since the operation is carried out with the obligatory tension of the line, you need to press it against the rod by hand just above the first ring in order to adjust the tension. In this case, you should know how to wind the line on the reel without cutting your fingers with it. You can put a glove on your hand. And you can skip the line between the pages of a small book, then it gets additional alignment during the winding process.

Rewinding the line from the reel

The assistant should gradually release the line (scrolling a pencil) and keep the reel itself straight. Fixes the bobbin each in different ways, for how much imagination is enough.

When self-spinning, you need to observe that the line does not twist, for this, pay attention to the bottom of the reel. If you miss the twisting, then the tangling of the fishing line cannot be avoided. Wrap a rag on your finger or put on a glove (so as not to cut yourself) and hold the line with it at the beginning of the spool (to control the tension).

Spinning reel winding

The amount of line is also indicated in the reel markings. Therefore, study the coil very carefully before purchasing.

Wrap the fishing line cross to cross, so it is more reliable and leave 1-1.5 mm still free.
Before the winding itself, you need to adjust the spinning washers (4-6 pieces).
The new coil is tuned to a cylindrical winding method. You can also adjust for straight or reverse winding cone.

For setting the washers, instructions are attached to the new reel, some washers are on top of the axis near the spool, and others are inside. If the location of the washers is upper, then this is a coil with a front functionality, if it is an internal one, then with a rear functionality, respectively, the winding adjustment is different.

Reel winding

This reel is designed to hold one hundred meters of line.

First, open the line guide (special bow on the reel).
Then, starting with a small one and further in ascending order, we pass the line through each ring, we reach the spool and fasten the line on the spool by tying a knot, or cling to a stupor.
At first, wind a couple of turns with your hands, and then twist the reel handle, carefully observing the uniformity of the line.

How to wind the line on a reel: tips for beginners

It is always difficult for a beginner amateur angler to comprehend all the “wisdom” and secrets of fishing. One of these “tricks” is the system of the correct winding of the fishing line on the purchased reel. But the correct location of the fishing line on the reel affects the fishing result.

Line quantity and tension

Remember, you need to wind a new line, since the old one can break at any time and cause a lot of trouble.

While fishing, observe the behavior of the line, if it constantly waddles over the side, then perhaps it should be moved away from the edge by half a millimeter. So you can eliminate the inconvenience.

Winding on a baitcasting reel

The baitcasting reel is a separate type of the pull-back reel. In it, the thickness of the fishing line must exactly match the inscription on the reel.

Correctness of winding on this reel:

Use a knot to secure the fishing line.
Place the reel on the spinning rod and pull the braid through the right ring.
Tighten the brake and clutch.
Carefully wind the line by turning the spool handle.
Carefully adjust the desired tension using the finger cut protection.

How to properly wind the line on the trimmer spool?

Despite the fact that gardening equipment has been used for quite some time, it is still a novelty for some owners of private houses. That is why there are often questions about how to properly wind the line on an electric or gasoline trimmer.

This is essentially a simple operation, but all its stages must be performed correctly in order to achieve the desired result. over, in the operating instructions, only a few manufacturers provide an answer to this painful question. Explore the article and find out how the line winds around the trimmer reel.

The order of winding the line on the trimmer spool

First of all, you should know that trimmers have different working attachments. The reel can be designed for different lengths and thicknesses of the line. this point should be taken into account when purchasing consumables.

So how do you load the line into the trimmer reel? All work is divided into several stages:

First you need to disassemble the trimmer head.
Unscrew the nozzle by rotating the drum to the right.
Press with your fingers on the two latches located on different sides of the entrance, and remove the top cover of the nozzle. You can pry off the cover with a screwdriver. This should be done carefully: reels with automatic line feed have a spring that can forcefully throw the cover along with all the contents of the reel.
Remove scraps of old fishing line.
Now you need to find the middle of the line. To do this, unwind it to the required length (for example, 10 m), cut it off and fold it in half.
Hook the middle of the line into the existing recess or insert into the hole specially designed for this. And start winding. The direction is indicated by an arrow, which is usually marked on the trimmer reel body (usually against the rotation of the drum). Some models have a double-sided spool: in this case, the line should be wound in different directions: one end in one direction, the other in the other, while the loop of the line must be wound into the dividing slot in the middle.
Leave loose ends of the line about 20 cm each. Later they will need to be fixed in the recesses.
And finally, the last step will be the assembly of the drum. Reinstall the washers and spring. On the top ring of the reel there are two notches where you need to tuck the antennae of the fishing line. Thread them through the holes and place the spool in the drum, trying to tighten the line without displacing the spring.
Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

When you turn on the trimmer, excess line will be cut off by the trimmer blade.

As you can see, winding the line on the trimmer reel is not difficult: the main thing is to do everything right. And here are some more tips that will come in handy when choosing a fishing line, winding it and subsequent work:

fishing line comes in different thicknesses and with different sections. The best option for winding is the “native” line for this model;
never use fishing line or metal cables for the trimmer. This replacement may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure not only the lawnmower himself, but also those around him;
the line is cut when the trimmer is in contact with hard objects. Try not to allow this, otherwise you will have to stop every time, turn off the device and rewind the line on the reel;
Use regular line for cutting lawn grass and pigtail line for coarse weeds. It is more durable and will not constantly cut.

In the model with one groove

The line must be pulled into the hole, and its mustache must be folded together and aligned.

Then winding is performed in the opposite direction to the rotation of the bobbin on the mower. There is often an arrow inside the spool indicating how to put the line on correctly.

The ends of the string are fixed in special grooves or simply temporarily held by hands and pulled into the hole located on the outside of the bobbin.

After that, the spool is closed and attached to the rod, after which the mower is ready to work.

In the version with two grooves

The line is first folded in half to determine where the middle of the fold is.

Next, the loop formed at the bend is threaded into the groove that is formed between the two grooves.

After that, you can wind both bars of the line in a separate groove.

You can fix the mustache and assemble the coil completely in the same way as described above.

Opening a reel for the first time and winding a new line is not always easy. Over time, this procedure becomes almost automatic and will not take much time. Some reels have an automatic system that spins the line by itself. As a result, it remains only to correctly set the end of the line, and you’re done. In such models, the string must be put into the hole that is on the outside of the body. Next, the bobbin is assembled, and when the winding rotates, the fishing line is put on it.

The convenience of such reels is that it is impossible to wind up incorrectly, since the line will always turn only in the right direction.

How to choose the right line?

Nylon lines are suitable for both electric and gas powered trimmers. This consumable can be used for both hand tools and a wheeled lawnmower. It is important to choose the right line, as this directly affects both the result of the work and the service life of the unit. Of course, it is very easy to get confused in the offered assortment of lines, especially for beginners. However, there is a lot of advice from experts and those who have already tried various options.

For an electric trimmer less than 500 W, a thin line with a diameter of 1 to 1.6 mm is suitable. She will perfectly mow lawns with low grass. If the power of the tool is in the range from 0.5 to 1 kW, then it is better to give preference to a line with a diameter of 2 mm or slightly more.

This will be enough to cut thin grass or overgrown weeds, but not too thick.

For petrol trimmers and lawn mowers, line less than 3 mm must not be taken. This thickness will allow you to easily cope with any weeds, dry stems, dense grass. Diameter over 4 mm is only suitable for high power lawn mowers. It turns out that thick line is necessary for powerful technique. It is not recommended for use with low power trimmers, otherwise it will work poorly, constantly winding around the reel and creating additional load on the engine.

Typically, a standard package contains up to 15 meters of line. However, to replace the string on a reel, a length of about 7 meters is sufficient. It also happens that the line is produced in bays of 250-500 meters. When choosing a string, it is imperative to specify the date when it was produced. Nylon that is too old can dry out and become too brittle. If this happens, then you can soak the fishing line for a couple of hours in water, but it will not be completely the same.

When choosing an important parameter is the section of the string, which can be of several types.

The round section is versatile. It is used for mowing grass of medium thickness and density. May make excessive noise during operation, but not used too quickly.

A square or polygonal section is more efficient than a round one. Sharp corners cut plant stems faster and with better quality.

Ribbed, twisted and star-shaped sections are the most effective. Such a fishing line manages to mow the grass very quickly. And its main drawback is its rapid wear.

Trimmer line is made of nylon, which is durable, lightweight, low cost and durable. To make the cost of the material even cheaper, polyethylene is added to it, but then the line overheats faster. Thick strings have a graphite or steel rod. Sometimes they are reinforced, which increases strength and service life.

It is worth noting that for two-piece strings are higher than for standard nylon.

How to reel?

Knowing how the reel is disassembled can speed up the line change process. It all depends on what design the coil has and how many antennae. Threading into a spool that has only one working mustache is quite easy, especially if you stick to a consistent plan.

Depending on the parameters of the reel and the length of the line set initially, it is recommended to choose a string from 2 to 5 meters.

First you need to remove the bobbin from the tool, and then open it.

One of the ends of the line must be installed in the hole inside the bobbin.

Next, the string should be wound onto the drum. And this is done in the opposite direction from the normal rotation of the spool. Usually on the trimmers on the inside of the bobbin there is an arrow that shows in which direction to wind.

Part of the line must be pulled out and fixed in a special groove located on the inside of the reel. Its purpose is to hold the winding while bringing the bobbin into working condition.

The end of the string must be passed through the hole located on the outer part of the bobbin.

At the last stage, you need to collect the parts of the bobbin and put it on the mower bar.

The installation of the line on a reel with two mustaches occurs in a slightly different way. First, you need to determine how many grooves go along the inside of the reel on which the line is put. There are options with one groove, and then both mustaches must be wound together. There are also models with two grooves, when each of the mustache goes separately.

For all double-whisker reels, a string between 2 and 3 meters is recommended.

Device in the mower

In the trimmer, the element on which the string is pulled is very simple. It is called the “coil”. It usually consists of an upper and a lower part (grooves), between which there is a partition with a recess. It is on these grooves that the fishing line should be wound. However, first it is pulled through the recess.

Before removing the coil, unscrew the special button located directly on the mower body. Remove the reel from the mower before changing the line.

It is not difficult to do this, but there are some peculiarities depending on the trimmer configuration and the coil itself.

In small electronic mowers, the motor and reel are at the bottom, and buttons are located on the sides of the reel. If you press them, you get the upper groove of the reel and the part where you need to wind the fishing line.

In bent-arm mowers that do not have a knife, the reels have special two-horned nuts. In such tools, you must hold the bobbin so that it does not move, and at the same time turn the nut clockwise. It is she who holds the entire reel, which is then easy to remove.

Straight boom mowers that can be fitted with a blade have a hole just below the reel. To remove the coil, a screwdriver is inserted into this hole, while the bobbin is fixed. After that, you need to turn the coil clockwise and remove it from the unit.

Sometimes there may be latches on the coil in the form of latches. They must be pressed to separate the coil parts. It is also possible that the top and bottom of the bobbin are connected by a thread. In this case, it is enough to grasp the top and bottom with your hands, and then twist in different directions until they unscrew.

Lawnmower fishing line: how to choose and wind?

How to choose the right line?
Device in the mower
How to reel?
Safety engineering

With the arrival of spring, summer cottages are becoming the main residence of many of our compatriots. However, with the arrival of warm days, there is such a problem as fast-growing grass. It is inconvenient to constantly mow it with a hand scythe, and not all types of grass lend themselves to this old working tool. It is much more convenient to use modern lawn mowers for these purposes. Particularly popular among them are devices with a fishing line, which is easy to change if necessary.

Safety engineering

You can find out how to replace the line on the trimmer from the video below.

Sources:

http://fb.ru/article/68447/uu-kak-namotat-lesku-na-katushku-instruktsiya
http://evrikak.ru/info/kak-pravilno-namotat-lesku-na-katushku/
http://womanadvice.ru/kak-pravilno-namotat-lesku-na-katushku-trimmera
http://stroy-podskazka.ru/gazonokosilki/leska/

Lawn Mowers line, onto, properly, wind