How To Put The Line On The Electric Trimmer

How to properly trim the coil. We wind the line on the trimmer spool

Owners with their own plots often face the problem of lawn maintenance, namely the need for high-quality mowing of grass. For these purposes, either a hand or a scythe powered by electricity is used. a trimmer (see Photo). It is clear that working with the electric model is much easier and faster. The grass is mowed with a line rotating at high speeds. But during operation, the thread wears out over time and requires a change. So how to wind the line on the trimmer reel with your own hands?

Step-by-step instructions on how to wind the line onto the trimmer spool

With the arrival of spring, you often spend your time at the cottage or in your garden. The trimmer will protect you from problems such as grass and weeds. This tool easily trims and mows grass in difficult terrain, where a conventional lawnmower cannot do it. Trimmer. A very effective and convenient tool for cutting grass along fences, flower beds, houses and garden aisles. Several types of garden trimmer were invented (gasoline, electric and battery). It would seem that everything is fine, in your arsenal there is such a wonderful assistant, but over time, the cutting element wears out and it becomes necessary to replace the finished line. And not everyone knows how to fill the line in the trimmer. We suggest using step-by-step instructions with attached photos.

Instructions on how to wind the line on the trimmer spool

• 1. First you need to disassemble the trimmer head. Press the latch on the product body and turn the lid clockwise. Removing the bobbin.
• Now we have to figure out how to wind the line on the trimmer reel. We measure about 6-7m of fishing line and insert its end into the hole of the bobbin.
• We reel the fishing line from both sides. The winding direction is always indicated by an arrow on the bobbin.
• Leave the ends of the 15 cm long cutter free. Do not wind too much line. Leave 6mm between the outer edge of the bobbin and the line.
• Insert the remaining two ends of the line into opposite holes in the bobbin.
• We fix both ends in the grooves on the head body.
• The spring is carefully placed back into the bobbin guides and into the head body.
• In order to thread the line into the trimmer correctly, it is necessary that the bobbin goes back into the head body (press it lightly). Pull the loose ends of the line out if necessary. Pull the ends of the cutting element sharply one by one so that they come out of the slots in the bobbin and pass freely through the holes on the head.
• So, we figured out how to wind the line on the trimmer reel. It remains only to align all the grooves on the head body and close the lid. Then we press on the bobbin and begin to rotate it counterclockwise until it stops. While holding the bobbin, turn it slightly clockwise and release it. If there was a clicking sound, then it snapped into the head. If this did not happen, then you need to repeat the action again.
• Pull out the loose ends of the line until they stop.

Types of fishing line

The trimmer thread can be divided into types according to its diameter. It can start from the smallest. 1.2 millimeters and go up to 4 millimeters. The most commonly used is the 2 mm diameter. But it must be selected strictly individually, based on the specific model of the device. Often the required product diameter is indicated in the product passport. Usually, the more powerful the trimmer, the larger the line diameter should be. For example, it is best to wind a thread with a diameter of 2.4 mm on a spool of lawn mowers, and for a product with a weak engine, a thread diameter of 1.6 mm is suitable.

Fishing lines also differ in the type of section. It can be round (for mowing ordinary grass), square (for soft and often mown grass), with sharp edges (for tall grass), with notches (for thin grass), as well as complex (see photo). The latter can be refueled not in all types of devices. It should be noted that the line is intended exclusively for mowing grass. To cope with other types of plants, you need to use a lawn mower with a sharp knife. The length of the threads that can be tucked into the trimmer can range from 10 to 100 meters.

How to wind the line onto the trimmer spool

Product spools can have different yarn feeding systems. It can be manual, semi-automatic or automatic feeding. Depending on this, it is necessary to wind the fishing line. So how do you thread the bobbin? To begin with, the cap is unscrewed on the coil (see). If the thread on it is left-handed, then you need to turn it clockwise, and not as usual.

Such a thread is made so that during the operation of the product the trimmer head cannot unwind. To thread the thread, you need about 5 meters of material (see photo). It must be folded strictly in half, the center must be inserted into a specially designated place on the apparatus and wound in the direction of the arrow, which must be drawn on the coil, as in. After that, you just need to screw the cap.

A country toilet is an obligatory attribute of a garden plot. Even if they are not going to build a summer dwelling, for the whole day.

The suburban cottages of the inhabitants of megalopolises are less and less reminiscent of garden houses, these are already quite modern “summer cottages”. places for recreation and hobbies.
Source: http://stroimdelaem.ru/namatyvaem-lesku-trimmera/

How to wind the line correctly on the trimmer spool

Many, having worked out the factory line on a recently purchased trimmer, try to wind a new one, but cannot, because they do not know how to properly wind the line on the trimmer spool (bobbin). It seems that there is an instruction, but it still does not work. Let’s try in this article to deal with this issue.

So, in order to wind the line, you first need to remove the spool from the trimmer. The removal method will depend on the type of trimmer.

On small, bottom motor electric trimmers (when operating near the ground), the reel usually has two buttons on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When disassembling, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to wrap the coil body itself with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, trying not to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers, in addition to fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, gently rotate the coil until the screwdriver crawls even deeper, and the coil will lock. Now turn the whole coil clockwise (since the thread is left-handed) and remove it from the trimmer. Then we disassemble the coil. It can be assembled with latches or twisted with a lamb. If the coil is on latches, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and with the other; top, and start turning them in opposite directions. When disassembling such a coil, you also need to make sure that the spring inside is not lost.

Now, having removed and disassembled the coil, we proceed, in fact, to the main question # 8212; how to wind the line correctly.

If your coil is designed to work with only one tendril, then it’s simple. You need to unwind 2-4 m of fishing line (depending on the size of the reel), find a fixing hole for the line on the inside of the reel, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. After winding the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inner part of the reel and designed so that the line does not unwind at the time of collecting the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and thread the outer piece of fishing line into the existing hole, assemble and put the coil back on the trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both tendrils are wound along this one groove. If there are two grooves # 8212; then each antenna is wound along its own groove. A reel with one groove must have a through hole through which the line is threaded. We unwind 2-4 m of fishing line, thread it through this hole so that it sticks out equally on each side of the fishing line. And we simultaneously wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little fishing line unwound, fix the resulting ends in special grooves, and if they are not there # 8212; hold with your fingers. We pass both ends into the existing holes on the outer casing of the coil. We collect the coil and attach it to the trimmer.

If there are two grooves, fold a piece of fishing line 2-4 m long in half, insert the loop obtained at the place of the fold into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option.

There are also spools in which the fishing line is threaded through a through hole on the inside, the ends of the fishing line, without winding, are threaded completely through the holes on the outer body of the reel, they collect the coil and begin to rotate the button, which is usually pressed, in order to release the fishing line during operation as it wears out. Rotate the button # 8212; the fishing line itself is wound inside. At the same time, twist it to # 171; wrong # 187; direction will not work, since it can only rotate in one direction.

That’s all on this issue. Now you know how to properly wind the line around the trimmer spool.