How to put the line on the trimmer reel correctly

line, trimmer, reel, correctly

Winding profiles (taper)

For different reel models, the turns of the line on the spool are applied in different ways. In high-quality products, the cylindrical and conical winding method is used. The line laid in profile forms a straight line. With a cylindrical winding, this line is straight, parallel to the spool, with a tapered winding. inclined.

The straight tapered shape tapers towards the front edge of the spool, the opposite one widens. Straight taper reduces line friction. Reverse styling reduces the likelihood of spontaneous line dumping.

There is also a third type of winding. chaotic. Usually used in cheap Chinese fishing rods. And if such winding can still be tolerated using ordinary fishing line, then the use of a cord in such a reel should be abandoned. Bad casts, beard, overlaps and entanglements are guaranteed. This leads to mishaps in fishing and can also ruin the mood of every fisherman.

Precautions for Hand Winding

Since the operation is carried out with the obligatory tension of the line, you need to press it against the rod by hand just above the first ring in order to adjust the tension. In this case, you should know how to wind the fishing line on the reel without cutting your fingers with it. You can put a glove on your hand. And you can skip the line between the pages of a small book, then it gets additional alignment during the winding process.

How to wind a fishing line on a reel: instructions

When collecting tackle for fishing, it is periodically required to change the line on the reel. This is a fairly simple procedure. However, it has a number of nuances. The correctness of this procedure will determine whether the thread will be flat when casting or will start to get confused. If the fisherman does the wrong thing, the thread may break. This causes a lot of difficulties. To avoid such troubles, it is necessary to consider in detail how to wind the line on a reel. This technology will be discussed in detail in the article.

What is backing?

It is usually difficult to determine how much line to spool. A standard spool is believed to hold one hundred meters of 0.3mm line. However, progress has stepped forward, and modern lines are becoming thinner, without losing the margin of safety.

How many meters of fishing line to wind on the reel, each angler decides for himself, depending on the fishing conditions. Therefore, it happens more and more often that the selected line is much smaller than the spool can accommodate. The resulting free space needs to be filled with something. Some people use electrical tape or nylon thread for these purposes, but this is not the best option. The adhesive on the tape that holds the bottom turns of the line peels off quickly. And the nylon thread dries for a very long time when wet.

Therefore, more and more anglers are inclined to the American method. to reel in the lower layer of fishing line is simpler and cheaper, and tie the main, higher quality to it. This turns of an inexpensive thread is called backing, in our opinion. reeling. It connects to the main strap with a self-tightening double loop, clinch or similar knot options.

line, trimmer, reel, correctly

The importance of winding correctly

In order for fishing to be successful, you need to carefully prepare for it. Otherwise, “terrible things can happen”. the weather is wonderful, the bite is excellent, and the tackle constantly fails and prevents you from taking advantage of the favorable fishing conditions.

EASIEST WAY TO STRING YOUR WEED EATER

To prevent this from happening, you need to set up all fishing accessories in advance. One of the most important steps in preparing for fishing is the correct winding of the line on the spool of the fishing reel. Failure to comply with the basic rules threatens the would-be fisherman with entanglement and line breaks, and fishing instead of pleasure will become a test for the nervous system.

The casting distance depends on the quality of such work. Correct winding ensures the casting of the bait at a distance that best matches the technical characteristics of the reel.

In addition, high-quality winding extends the life of the line by reducing mechanical friction and reducing the risk of beard when casting, which often requires you to cut the line. Therefore, before starting work, you need to consider a few tips from experienced fishermen on how to lay the line on the spool. This is a fairly simple procedure that even a beginner can handle.

Winding the thread by hand

You should also consider how to wind the line onto the reel by hand. If the fisherman has a telescopic spinning rod, it must be expanded into working condition. This is not necessary for a plug rod, you can work with the lower part of it.

Attach the spool to the spool seat. There is a hole in the reel on which the fishing line is wound. A rod is inserted into it, which can be used as a pencil, pen, knitting needle, etc. If the fisherman has an assistant, he will hold the axis on which the bobbin will unwind. If there is no assistant, you can hold the rod yourself between your knees.

On sale there are special devices for unwinding the line from the reel. Their advantage is that they regulate the force when winding the line and make it uniform.

The line is threaded through the rings, from the smallest top element to the spool. The thread is then secured in the spool with the line guide open. After that, it is lowered into the working position. You can start winding the line by rotating the spool.

Determining the amount of rewinding

In the question of how to wind the line on a reel, for beginners there is a difficulty in determining the amount of winding. It can only be established experimentally. Experienced fishermen advise to reverse the order.

If there is a second reel of the same, you first need to wind the fishing line on it, and then the reel attached to it. In this case, the basic rule should be remembered: you can correctly wind the fishing line on the spinning reel only if the level of its top layer does not exceed 3 mm from the side of the spool. After that, you should rewind the thread to the main shule, already starting with the backing, which, as it should be, will be at the bottom.

If there is no second same coil, the measurement is made on the main coil, then the line is unwound and rewound on it, already starting from the winding.

How to reel fishing line

Fishing is really exciting and exciting business. Beginner spinning players, of course, want to quickly join it and finally get a sensible result. The reservoir where you are going to fish has been selected, all the necessary accessories have been bought. There are rods, reels with lures and lines. too. However. even a slight, but still tangible nuisance can wait right on the shore, which sometimes completely disrupts the whole fishing.

Her name is the winding of a fishing line on a reel. Each coil seems to be equipped with an instruction with a basic diagram. But the fact is that with such an attitude, it will not be possible to catch a lot for sure. If the loop is wound incorrectly, the loop may be thrown off, and instead of removing the fish from the hook, then you will have to bother with untangling a lump from the fishing line with your own hands.

They start using spinning most often with tackles that are shorter (both reels and rods). The caliber of the bobbin in them is two to three thousand (that is, a hundred-meter line is not more than a third of a millimeter thick in this case, the limit). The winding structures can also be very different: this is a chaotic winding in a chaotic arrangement of Chinese samples (more or less suitable for monofilament, but completely inappropriate with a braided line), and such more professional formats as a straight cylinder, straight and inverted cone. And from the very beginning it is better to get used to those types of styling that are more serious, because this is not a whim, but a higher efficiency. Having saved a few hundred rubles in passing, you will then begin to curse everything in the world, when, instead of casting and biting (well, or just casting and waiting), fishing turns into a continuous struggle with “beards” and other overlaps of the line. Such a catch has never brought joy to anyone.

How to quickly wind a line on a spinning reel

The basic, fundamental rule is that the equipped line must be flat, like a ruler. For cylindrical winding, a straight line is optimal, and if a cone is chosen, then an inclined one. But in any case, remember firmly, only the line without bends.

How can this leveling be ensured in practice? First of all, we attach the bobbin to a fixedly placed rod-shaped object, on which it should scroll easily and freely. Pencils and knitting needles, fountain pens and screwdrivers, small metal tubes without sharp edges, and even a smooth and well-polished stick can act as a rod. As a last resort, find someone who agrees to hold.

Pull the line through every single rod ring. Tie a knot at the extended end. Now you can start threading the line to the surface of the reel. First, we fasten it on top of the bobbin in a circle, having previously lifted up the arc of the line stacker, and when another knot of the “Arbor” type is tied and tightened, the arc can be lowered.

Braided line loves to slip very much. This can be avoided by prying a piece of rubber under the attachment point (for example, cut from an unusable fingertip or worn-out glove), in extreme cases. support it with adhesive plaster, if there is no rubber.

And now comes the turn of the line winding. Turn the handle on the reel neatly and evenly. Make sure the line is tight all the time. It is imperative to support it, but only in tight gloves.

When winding up, avoid, as much as possible, ending it at the level of the bobbin collars. If you do not follow this rule, then self-resetting of loops or their eerie entanglement becomes very likely. To avoid such an outcome, pay attention that at least a millimeter or two of the fishing line remain unwound up to the side. On the other hand, exceeding the gap of five millimeters can make long-range casting impossible. Backing is a preventive measure (in fact, winding up the bottom of the main line of the auxiliary line, no thicker than three tenths of a millimeter, otherwise an even laying will become unattainable). Please note that almost all threads work well in backing, except for long-drying cotton and nylon.

See useful how to properly wind the line to the reel

It is possible to determine how much fishing line to throw on backing, it is possible only by experiments, there are no ready-made formulas and theoretical provisions on this score. Another bobbin is required. We wind the main forest on it, then backing (do not forget about the gap from the side). Next, we attach the main mount, to which we are already introducing the fishing lines in the reverse order. Visit our website and read more useful tips for fishermen.

How to wind line on a trimmer

During winding, the handle of the reel should be turned smoothly, without jerks and at high speeds. Care must be taken to ensure that the thread lies in straight parallel lines. Do not wind too thick line that is not intended for this reel.

Smoothly winding fluorocarbon, you should pay attention to how much is left to the side. The optimal distance is 2 mm from the top layer to the edge of the side.

How to properly attach the thread to the trimmer

Winding the line to the trimmer. it’s a simple matter, but it requires some skill. First you need to firmly attach the reel to the rod. Then pass one end of the fluorocarbon through all the ears of the rod and fasten it to the spool. To do this, you need to raise the bow of the coil, wrap the fishing line around and tie with an Arbor knot.

If the thread is stiff or thick, then before winding it should be immersed in warm water, after this procedure it will become more elastic and lie smoother. When winding, it is desirable that there is an assistant who would hold the bobbin with the fishing line. In the process, you should slightly slow down the fluorocarbon with your finger or a soft cloth.

Backing

Every fisherman must know how to wind the line on the trimmer and what is backing. Backing is a reel spool reel. For this, a thread with a diameter of 0.1 to 0.3 mm is often used. If you use a thicker fluorocarbon as a reel, it can lead to uneven and uneven laying of the main line. It is highly undesirable to use wet materials for backing, such as nylon and cotton threads. They are unable to dry completely for a long time, which leads to debate, and the replacement of the line on the trimmer. these are additional financial costs.

line, trimmer, reel, correctly

The amount of thread required for backing can only be determined empirically. This requires two spools. The required amount of working line is first wound onto one, and then the backing is wound in such a way that two millimeters remain to the edges of the side. After this procedure, the spool with wound fluorocarbon is removed and an empty one is put on, on which the thread is wound, only in the reverse order. Backing first, then working nylon.

How to wind line on a trimmer: examples and recommendations

As a rule, before going fishing, it is necessary to check all the tackle, the reliability of the connecting loops and the sharpness of the hooks. But do not forget about the backing, which is wound on a reel, because the success of fishing in general will depend on how you wind the line around the trimmer. Incorrectly wound, it can lead to a “beard”, which is difficult to untangle and which takes a huge amount of precious time, the casting distance can be significantly reduced, and in general in such a situation it is better not to fish.

Coil selection

Beginning fishermen, due to their inexperience, pay little attention to the choice of a rod and tackle, but the right equipment is the key to the success of fishing. Usually, spools are purchased with a spool size from 2000 to 3000, which can accommodate 100 meters of line with a number from 0.2 to 0.3 mm.

In addition to their size, they differ from each other in the way they are wound on a bobbin. You can wind the line on the trimmer spool with straight, cylindrical or tapered laying, it all depends on the model. It is also worth paying attention to the country of origin of fishing tackle. If the reel is of Chinese origin, from a cheap series, then always be prepared for line tangling during casts and the appearance of a “beard”, in addition, the cheap version quickly fails and requires repair or replacement.

With high-quality winding, fluorocarbon should form a strictly parallel stacking relative to the spool with a direct winding method, and inclined with a tapered.

What should be the length of the working thread

It all depends on the method of fishing and the reservoir. If a small length of line is required for fishing, then it should be less; if a long cast is required, then more fluorocarbon is needed. For a quick change in the field, every angler should know how to change the line on the trimmer. If the spool of the reel is deep, then approximately two-thirds must be filled with a cheaper thread, and the remaining part should be wound with working fluorocarbon, which is necessary directly for fishing. The reel should consist of a thinner line than the working line, this will increase the density and not fall through the main.

Storing nylon thread on a spool

How to wind the line on the trimmer. sorted it out, now let’s talk about storing fishing tackle, in particular fluorocarbon on the spool. For a long service life of the thread, you should adhere to several rules, the implementation of which allows you to save money on the purchase of new equipment.

It is important to remember that after fishing, the line and parts of the reel get wet, they should be well dried. Poorly dried fluorocarbon melts very quickly and becomes unusable. It becomes brittle and can break at the most crucial moment. To prevent this from happening, after seasonal fishing, the line from the reel should be rolled up and spread on the floor so that it dries well. This procedure should be carried out with backing (reeling). You can dry the nylon thread after each fishing trip if you go to it once a month.

You already know how to change the line on the trimmer, it shouldn’t be too difficult. Always store your fishing tackle in a dry place, this will guarantee reliability and durability.