How to refuel the coil of the Lawn mowl Stihl.

20th May 2023

Trimmer for STIHL FS 38 grass how to refuel a fishing line for a trimmer. Antirun.Ru

First, for winding the fishing line, it is necessary to remove the coil (bobbin, spool) from the trimmer for the grass. certain acts will depend on the difficulty of configuration and the type of product itself:

Small electronic trimmers for grass with a working location of the motor and coils at the bottom, usually have side buttons on both sides of the bobbin. With the simultaneous press on their highest part of the coil, together with the internal contents for winding the fishing line is disconnected, while the lower remains on the trimmer. The analysis of the bobbin is better to create in an even smooth place, so that the spring does not jump out and not be lost;
Electronic and gasoline trimmers for grass with a curved rod without the ability to install a knife, usually have coils with a special lamb: in similar structures, you should hold the rogue in a motionless position with one hand and the other counterclockwise twist the fixing bobbin on the bar barack. How to refuel a fishing line for a trimmer trimmer for grass? How to refuel a fishing line for a trimmer to a trimmer coil for grass. It is clear how to charge a fishing line for a trimmer for a trimmer for grass. After disconnecting the nut, the whole bobin is removed.
Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such mutual placement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third options of coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. How to refuel a fishing line for a trimmer in how true a cheap fishing line for a trimmer. 2. On your site. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the back of.

Which fishing line for a trimmer to choose to refuel a lawn mower

The thickness of the polyethylene thread depends on the model of the technique and varies from 1.2 to 4 mm. She may be:

With a round section. this is the most durable material for mowing herbaceous plants;
with curly section. used to mow soft plants;
twisted. used for thin grass;
professional type, is not suitable for all models of technology.

Read how to replace a fishing line for a trimmer on a trimmer Carver video

To change the fishing line for a trimmer on a lawn mower, it is necessary to purchase a cutting thread that will be ideal for a particular type of mower.

How to wind a fishing line for a trimmer to a trimmer coil for grass: Key points

A gasoline or electric trimmer for grass is an indispensable assistant in the arsenal of a modern summer resident or owner of their own house.

Thanks to these garden devices, you can easily bake even a large personal plot.

After acquiring this tool and performing several mowing, many people think about how to correct the fishing line for a trimmer to a trimmer coil for grass.

For an inexperienced user, the first operation to replace it will seem problematic and laborious, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

For both cases, a fishing line for a trimmer 2-3 m long is taken.

In a single.bonhean coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side inside the arrow is usually indicated the correct direction of the winding.

In the presence of fixing grooves, the ends of the fishing line are threaded into them or hold the fingers of the free hand, spread into the through hole of the outer half of the bobin, the spool is locked and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Refueling coils with a thread of various types of rods

With two.stringed automatic heads:

First you need to press the clamp until the click appears, remove the lid. Carefully turn Bobin so that she can disconnect from the holder. Extract her. Measure two segments of cutting thread of the same length

To make further work easier, the ends of the fishing line need to be cut off at an angle. Take one end and put in a special hole in the coil. It can also be slots, grooves, clamps, etc. Further, in the direction of the arrow, you need to wind the fishing line for the trimmer, and quite tightly and evenly. In a special ear on the coil, it is necessary to fix the end of the fishing line. The second half of the fishing line is subject to the same operation, only on the other half of the coil. Next, install the coil in the head of the trimmer for the grass. And pass the rest of the fishing line in the hole in the head. Then carefully straighten the thread and close the lid. If the fishing line for the trimmer is long, then it is better to cut off the excess. About fifteen centimeters should remain on each side.

The thread is threaded into the hole that is inside;
Fix the ends of the thread in grooves on the case.
The coil is collected and pressed by a special button;
After that, the fishing line for the trimmer itself begins to dangle in the right direction.

You should very carefully and carefully refill the cutting thread into the unit, because not only the purity of the garden plot depends on the correctness of its winding, but also personal safety

If the coil allows you to wind fifteen meters of thread, then you should not wind so much, there is enough ten, that is, if you fold in two layers, you get five meters each. With another capacity of the fishing line, it is worth using the same rule. In the case when an ordinary round thread is used, it is better that it is 3.3 mm with a diploma. If this is a figured fishing line for a trimmer, then its thickness should be less, for example, 3 mm. It is better to wrap both segments of the fishing line at once on the spool, and you need to start with its bending

It is important to prevent overlap in the direction of the arrow. It is also important to be able to perfectly pull the thread

There will be a thread to be pulled, it may go over. If not unit, can twist. In order not to cut your hands on the figure thread yourself, you should wind it in gloves. No need to leave the ends of the fishing line long. This can lead to its tightening.

Specifications

Trimer type for grass Stihl FS 38. portable. Speasing width for 1 passage. 38 cm. The tool in question is equipped with a gasoline two.stroke engine, 0.90 l/s. The working volume is 27 cubic meters. cm. The maximum engine speeds reach 9500 rpm. The fuel tank is designed for 0.33 l. Deci and case material is made of wear.resistant plastic. The bar has a curved shape, and the handle D-shaped. With its dimensions, the weight of the motorcycle is only 4.1 kg. Trimmer fishing line has a 2mm thick.

Speasing width, see	38
Engine	Two.stroke, gasoline
Power, l/s	0.90
Engine revolutions, rpm	9500
The volume of the fuel tank, l	0.33
Working volume, cube/cm	27

How to wind a fishing line for a trimmer to a trimmer coil for grass: Key points

A gasoline or electric trimmer for grass is an indispensable assistant in the arsenal of a modern summer resident or owner of their own house.

Thanks to these garden devices, you can easily bake even a large personal plot.

After acquiring this tool and performing several mowing, many people think about how to correct the fishing line for a trimmer to a trimmer coil for grass.

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

For both cases, a fishing line for a trimmer 2-3 m long is taken.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Refueling coils with a thread of various types of rods

With two.stringed automatic heads:

The thread is threaded into the hole that is inside;
Fix the ends of the thread in grooves on the case.
The coil is collected and pressed by a special button;
After that, the fishing line for the trimmer itself begins to dangle in the right direction.

You should very carefully and carefully refill the cutting thread into the unit, because not only the purity of the garden plot depends on the correctness of its winding, but also personal safety

It is important to prevent overlap in the direction of the arrow. It is also important to be able to perfectly pull the thread

Operational properties

Portable trimmer for the grass Stihl FS 38 belongs to the class of amateur. It is intended to care for small garden areas. Such motorcycles become indispensable assistants if it is necessary to tidy up the territory where it is impossible to use a wheeled lawn. For example, in hard.to.reach places, under trees and shrubs, near flower beds and fences. The grass braid is equipped with a simple and reliable 2-stroke engine of its own production. Carrying out a mixture of gasoline and engine oil. This engine provides simplicity of design, operation and service. As well as high capacity of work and torque.

Whatever company you have a trimmer for the grass for preparation are the same for all types. Disassemble the device, or rather, remove the coil from the head of the trimmer for the grass. To do this, we click on the fixers located on the sides of the head of the head, and turn the head clockwise.
In order to open the mowing head without problems, click on the side latches, if you do not succeed with your hands, use a flat screwdriver to help you help. We take out the coil from the head.
In order to correctly choose a fishing line for a trimmer for your equipment, digital designations must be applied on the inside of the coil, which indicate the thickness and type of permissible fishing line. All designations are indicated, as a rule, in millimeters.
If you have not found any numbers, then the maximum permissible diameter of the fishing line can be determined by a through hole for lingering the fishing line. The fishing line for the trimmer should go forward and backwardly.

The process of winding the fishing line on the reel

After all the preparatory actions, we need to correctly decide how exactly a fishing line for a trimmer, by turning the cover or in the opposite direction will be washed on your device.
We measure approximately 7 mm cutting material and at one end we insert it into the opening hole. It is worth noting that the fishing line for the trimmer is wound precisely on the model of mowers from two side. The direction of winding of the fishing line in such models is indicated on the bastard itself.
The fishing line for the trimmer is excreted to about 17 cm freely so that weeds can be cut off with the ends. Add that you should not wrap a fishing line for a trimmer for a huge length coil. About 5 mm leave the distance from the fishing line to the edge.
The two ends of the fishing line are inserted into the holes. Both of these ends should be reliably fixed on the device case.
The springs extracted from the coil (if any) insert the same as they were extracted, t.e. in the backlog and the body of the head itself.
To determine whether you have inserted a fishing line for a trimmer in a trimmer for grass, you need the element itself (bobbin) itself can easily be inserted into the body of the head of your device. If necessary, remove the free ends of the fishing line to the outside. To achieve this, you need to pull a fishing line for a trimmer through the holes in the bobbin with a sharp movement.

So, let’s say, you figured out how quickly, and most importantly, to correct the fishing line for a trimmer to the coil of the trimmer for the STIHL grass. All that you have left is to insert everything into the grooves and fix the main cover on the device. Then you can press the bobbin itself and make movements counterclockwise until you feel the emphasis. If you do not feel the emphasis, then most likely you were not corrected for a trimmer for a trimmer and you will have to start everything from scratch.

What can be used instead of fishing line

Most mowers are interested in others or sellers in specialized stores about what can still be used (replaced) except for the fishing line. Many of them begin to experiment and use unsafe methods, installing different cutting elements on their trimmer for grass, including copper wire, metal, some manage to use strings from guitars and even cables, and someone is completely a fishing line for fishing networks.

If instead of a special cutting element, say fishing line, install a metal cable, then your trimmer for grass can “turn” into a real dangerous weapon not only for you and your eyes, but also for all people around you nearby. This is due to the fact that during the work of the trimmer for the grass, the steel cable will constantly work, which will lead to confusion, and its small pieces can fly to all sides with a huge speed.
The same can happen if a copper wire is used instead of a steel cable, but in this case, the pieces of separation from copper wire will be slightly larger and may give you an even greater injury. And if God forbid, accidentally catch such a cutting element by the leg, then after that 100% is guaranteed a deep cut of soft tissues, and in some cases, all this can lead to amputation of small limbs (fingers) of the legs and even hands. Therefore, our advice to you, do not use any other cutting elements, except for fishing line, for your own safety and others.

Replacing fishing line in trimmer: 2 simple ways

Trimmer for grass is the necessary and useful tool for a summer cottage and a private house. Many own and actively use it, but not everyone knows how to replace a fishing line for a trimmer in a trimmer, especially at first.

In this instruction, we will analyze the entire replacement process step by step. Looking ahead, there are two ways to refill a fishing rod with a fishing rod. There is no fundamental difference. the difference is that in the first case, one fishing line for a trimmer will be refueling, folded in half, and in the second there will be two segments of these forests.

The first way

The prepared segment (in this case, it is 4 meters) is bent approximately in half-one segment should be 15-20 cm longer, and inserted into a special gap located on the dividing partition.

A fishing line for a trimmer is wound in a particular direction. This is done in an interference, the fishing line for the trimmer is neatly distributed. In this case, you need to wind the segment, which is longer into the section, which is closer to the button.

There are designs in which there is no division of the coil into two sections. This does not change anything, the fishing line for the trimmer is wound in a similar way. It is only necessary to ensure that the segments do not overlap among themselves.

The first should end the segment that is located at the bottom of the coil, t.e. closer to the fixing holes.

This tip is placed in the corresponding diameter hole. Trimmer fishing line is reliably fixed.

A long segment wraps another half turn. There it is similarly fixed. At the same time, the segment crosses another coil section.

A long segment wraps another half turn

The fixed ends of the wound fishing line are inserted into the holes of the trimmer’s corps of the grass.

The fixed ends of the wound fishing line are inserted into the holes of the trimmer’s corps of the grass

The coil is attached to the body. The ends of the fishing line are pulled with force so that the fishing line previously recorded in the holes of the coil of the fishing. This is easily determined by the characteristic sound (click).

The coil with the button is snapped in the corps of the trimmer’s trammer for the grass.

The coil with the button is snapped in the corps of the trimmer’s trammer for the grass

The replacement of the fishing line was successfully made. In this case, you need to install it back on a trimmer for grass and you can proceed to the span of grass.

It should be repeated, you do not need to remove the spool from the trimmer for the grass. this was done to clarify the process of replacing fishing line. You can disassemble the rogue in place, wind it up and put it back.

The tips so that they do not beat the trimmer casing for the grass, you can and should be cut.

Carburetor for a gasoline trimmer for the grass Union BTS-9252L, BTS-9256L

Gasinzin trimmer for Transmission FBC-452/2200

Universal coil for a benzotrimer

Gasinzin trimmer for Transmission FBC-522/2600

The coil is worn out from long work.

The first repair project is to solder a new extension cover made of nylon or plastic.

In order for the saw to stay in the hole, it was necessary to clamp it in the cartridge of the lathe and cut the groove under the locking ring using a cutter with a depth of 1 mm and 2 mm wide.

I leaned over the stop ring onto a trimmed pipe of water from a bicycle needle and removed an additional place.

After a simple repair, I put my head on a bureau, put on a shoe, tucked a fishing line for a trimmer and went to the garden for testing. Everything is working! Correctly! I pressed the updated speech. Trimmer fishing line continued. After mowing, the dust remained in place. Planned surfaces are not clogged with grass and earth.

The successful decision over the next hour was re.implemented on the second worn head. Now I have a spare!

If you carefully look at the attached drawings, you can guess along the bronze workpiece of the articular prosthesis “Tube plus tube”.

Or even with a protective cap on the trunk. Then a groove with a locking ring is not needed.

How to change a fishing line for a trimmer on a trimmer Stihl FS55

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

Testing the new lawnmower Stihl 510

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.capanal coils, the fishing line for a trimmer stretches into the through hole, its ends (antennae) are folded together and leveled, after which they are wound in the back of the rotation of the bobbin on the bar side. Snutry with an arrow exaggeally indicated the correct direction of the winding. If there is a fixing grooves, the ends of the fishing line are threaded into them or hold the fingers of the free hand, spread into the through hole of the outer half of the bobin, the spool is locked and attached to the bar of the trimmer product.

The difference in the winding of the fishing line in two-drummer coils is that at the first a segment of the fishing line 2-5 m long is folded in half (to determine the median fold), and the berth loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

The above will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correctly wind it. This operation is nothing complicated and, with a certain patience, will certainly be crowned with a furro:

How to choose a fishing line for a trimmer. length, diameter, restrictions

For any electric or gasoline trimmer for grass, you can use fishing lines of different manufacturers. However, the best option is the consumable of the same brand as the tool. It is believed that in this case it will benefit the durability of work and even reduce the consumption.

It is important to remember! You can not use fishing fishing line for a trimmer or metal cables for a trimmer for grass. This replacement is not effective and dangerous. The cable can injure not only the mower himself, but also others.

As for the length, it is worth counting on the estimated frequency of using a trimmer for grass. The more often, the more it is worth stocking up.

Information about the possible diameter of the fishing line is found on the body of the coil for a trimmer for grass. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose a suitable option, taking into account the features of the processed territory. The larger the diameter, the easier it is to mow hard grass.

Coil with one working osik

The easiest option and a simple sequence of actions:

The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the fixing technological hole located inside the spool.
The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobbin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Preparation. remove and disassemble the rogue

In most models of electroly and benzotrimmers, to replace the fishing line, you will need to remove the coil. Fubag tool allows you to skip this stage. For the instruction to be universal, we will still consider it in detail:

Fix the shaft. Insert a stop element into the corresponding hole. They may be a thin screwdriver or a metal rod.

STIHL RM 443 T Lawn Mower Overview | Fraser C. Robb

Unscrew the spool body. In our example. strictly in the direction clockwise.

Unscrew the lid in accordance with the direction indicated on the case.

The preparatory stage has been passed. You can go to the winding of the fishing line.

Preliminary preparation

First, for winding the fishing line, it is necessary to remove the coil (bobbin, spool) from the trimmer for grass certain acts will depend on the difficulty of configuration and the type of product itself:

Small electronic trimmers for grass with a working location of the motor and coils at the bottom, usually have side buttons on both sides of the bobbin. With the simultaneous press on their highest part of the coil, coupled with the internal contents for winding the fishing line is disconnected, while the lower one remains on the trimmer. The analysis of the bobbin is better to create in an even smooth place, so that the spring does not jump out and not be lost;
Electronic and gasoline trimmers for grass with a curved rod without the ability to install a knife, usually have coils with a special lamb: in similar structures, you should with one hand with one hand to hold the rogue in a motionless position, and the other counterclockwise twist the fixing bobbin on the staging barack. After disconnecting the nut, the whole bobin is removed.
Electronic and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and with unhurried rotation, such mutual placement is achieved when the screwdriver enters the holes and the bobin is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third options of coil, depending on the design, are versed in different methods. In the bobbins with a lamb, lamb is twisted, in the reels with the latches, the fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then they are quite turned with their hands in the back sides until they are completely developed.

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.bona coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in a flip direction of rotation of the bobbin on the bar the side of the snitches with an arrow indicate the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded into them or hold the fingers of the free hand, spread into the through hole of the outer half of the bobin, the spool is locked and attached to the bar of the trimmer product.

The difference in the winding of the fishing line in the two-drummer coils is that the line of the fishing line 2-5 m long is in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

The above will clearly show how to tuck a fishing line for a trimmer to the coil of a trimmer for the grass and correctly wrap it this operation is nothing complicated and, with some patience, will certainly be crowned with a furorur:

Replacement instructions. how to insert a fishing line for a trimmer

It should be noted that the coils in mowers can be different:

for functioning with one osik;
for functioning with two antennae;
The fishing line for the trimmer should be extended through the through hole, which is located inside the element.

And you should not confuse this part with an extension cord for a lawn mower on a coil, because despite the similar name these are two completely different elements.

In the first version, wound the cutting element is very simple:

On the inside of the coil element there is a fixing ear.
One mustache is inserted into it.
Refuel the nylon thread in the direction of the reverse rotation of the coil element.
You will need only 2 to 4 meters of fishing line. When the winding process is completed, put the small end of this cutting element outward and fix it in the groove that is necessary to fix the fishing line so that it does not spin during the functioning of the mowal.
If there is no special groove, then the end should be held with a hand so that the cutting element does not spin during the further collection of the element.
At the last stage, it is necessary to pass the outer end of the thread into a special hole located on the outer part of the element. After that, the coil can be inserted into a mower.

When the video works with two ends of the polyethylene thread, then it is necessary to take the following steps to refuel the fishing line for the trimmer to the lawn mower:

Inside, the coil will see how many recesses for winding are available (two or one). If one deepening, then both ends of the threads will be laid on this recess. If there are two of them, then the antennae are laid out separately. each by its own seizure.
It is necessary to rewind from 2 to 4 meters of polyethylene thread and pass two ends into the hole.
Wind both threads in one direction, reverse the drum.
When the entire fishing line for the trimmer is wound, the ends should be fixed in grooves or held with a hand.
Both ends are threaded in the ear from the outside of the clip body.
After that, the drum is assembled and inserted into a mower.

Coil element or video can have a completely different design, different from the previous two options. A fishing line for a trimmer can be extended through an ears, which is through and is located inside the coil. In this case, you do not need to disassemble the roller drum and manually wrap the plastic thread.

The polyethylene thread is threaded through the hole and rotates by pressing a special button. This button is located on the case and is intended for the operation of the equipment so that it is possible to produce a fishing line for a trimmer as it is worn.

How to refuel a fishing line for a trimmer to a trimmer coil for STIHL grass

How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction

Warranty production of the factory refueling of a trimmer for the grass will be in demand for fishing line substitutions. Having a very approximate idea of how to tuck a fishing line for a trimmer to the coil of a trimmer for grass without the help of others, the new ones without hunting take up this matter. How to wind a fishing line for a trimmer to a trimmer coil for grass

, how to refuel a fishing line for a trimmer to a trimmer coil for grass. Autocut for a trimmer for STIHL FS 55 grass refueling the fishing line in a trimmer coil for grass 2 part winding of the fishing line on. But with some abilities, the development of this simple science does not represent any difficulties, and the similar annotation presented below will greatly facilitate this process.

Read device for the ignition coil of the chainsaw

Technical characteristics of a trimmer for grass

In addition to the good quality of the assembly, the Stihl FS 38 lawn mower is highlighted by worthy factory parameters.

The list of the most important characteristics of the garden tool includes:

Power of the factory ICE. 0.9 liters. With. at 9500 rpm;
tank for refueling the fuel mixture. 330 ml;
maximum fuel consumption. 320 ml/h;
Coverage when mowing with a fishing line/knife. 38/25.5 cm;
sound effect on the operator. 97 dB;
Weight. 4.2 kg.

STIHL trimmer differs from analogues with modest dimensions. The length of the motorcycles is 147 cm with dismantled cutting equipment.

About the manufacturer Stihl

The history of this German brand begins in 1926. At the initial stages of its development, the company was engaged in the production and implementation of various components for washing and steam machines. It all began, like many companies, with a small production and narrow orientation, which made it possible to focus on the quality of the manufactured products.

In the early 30s, the first Stihl chainsaw was released, which is characterized by convenience and functionality in those days. The company is developing at a long time, constantly introducing new tools, which gives it the opportunity to enter the international market. And already in 1931 the first regular supplies of products in STIHL were organized

To date, the company has launched its activities in more than 160 countries of the world, opening new centers and production departments in Switzerland, China and many other states. This is understandable, because the assortment of the company is impressive: motoburs, gasoline sprayers, mowers, gasoline trimmers for grass, chainsaws and much more. I would like to note that Shtil chainsaws are very popular due to their functionality and acceptable price.

How to choose a trimmer for the head of the head?

So that the head of the mower is highly efficient, the owner of the bushore should approach it correctly. In this case, several factors should be taken into account:

An experience. If the buyer. Novice gardener, it is best to buy an automatic coil. Semi.automatic and manual coils are best suited for more experienced gardeners;
Material. The reliability of the coil depends on this. They are considered the most durable metal models, but they weigh much more than standard plastic devices. When working with a metal coil, the braid engine is under a large load, so you only need to buy them to work with a powerful brush;
The diameter of the used mowing fishing line. For medium power trimmers, coils are used, which can be tightened with a wire thickness of not more than 1.6 mm. lawn mower with a capacity of more than 2.5 liters. FROM. Lamps can be installed that can be delayed using a cutting cord with a thickness of more than 2 mm.

An important role in choosing a coil is also played by the simplicity of its design. For beginners, coils consisting of a minimum of parts are best suited. experienced gardeners can use heads with a large number of elements in their design.

TOP 3 most reliable drums for home use

The market has a rating of the most durable mowing heads. They are distinguished by the simplicity of the device, reliability and resistance to damage. These include:

3rd place. Bosch K-103. This is a universal coil weighing about 300 g. Most often used to equip Makita and Hyundai motolers. The model is characterized by low energy consumption, impact resistance and durability. The core and its other parts are made of forged steel, and the case. From plastic;

2nd place. Flymo 15. This semi.automatic model of a trimmer for grass is equipped with a thin cup, which increases the flow rate. Nevertheless, he worked perfectly when he mowed grass in rocky terrain. To work with it, you need to use only a thin fishing line for a trimmer;

1st place. EFCO 8100. This model is one of the most reliable mowing heads. It works in fully automatic mode, which facilitates its filling with a cut cord. Only thin hair is used to work coil. The model of the model is made of durable multilayer plastic.

Despite stability and durability, all these coils are much cheaper than other analogues of lower quality, which makes them leaders in the post.Soviet market.

The relatively high price of STIHL products can be scared away by many, but if you think about what is more important. reliability and good result or savings that are in harm with the quality? But, if you set out to save money, we offer you an option for the lawn mower with your own hands, collecting the device with your own efforts you will know all the nuances and the structure of the tool.

Of course, you can choose cheaper Chinese counterparts, but then no one can vouch for the result of the final work and for the life of the service, which is very short.lived among such models. So it is more profitable to purchase a mow from an authoritative company once, which is certainly Stihl, and enjoy stable work for many years of operation.

We carry out the winding of the fishing line

Sentlessly completed disassembly of the coil-pole without losing its spare parts allows you to go to the main task-wrapping a fishing line into the reel. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the fixing technological hole located inside the spool.
The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobbin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The first way

The prepared segment (in this case, it is 4 meters) is bent approximately in half-one segment should be 15-20 cm longer, and inserted into a special gap located on the dividing partition.

The first should end the segment that is located at the bottom of the coil, t.e. closer to the fixing holes.

This tip is placed in the corresponding diameter hole. Trimmer fishing line is reliably fixed.

Trimmer fishing line is reliably fixed

A long segment wraps another half turn. There it is similarly fixed. At the same time, the segment crosses another coil section.

A long segment wraps another half turn

The fixed ends of the wound fishing line are inserted into the holes of the trimmer’s corps of the grass.

The fixed ends of the wound fishing line are inserted into the holes of the trimmer’s corps of the grass

The coil is attached to the body. The ends of the fishing line are pulled with force so that the fishing line previously recorded in the holes of the coil of the fishing. This is easily determined by the characteristic sound (click).

The coil with the button is snapped in the corps of the trimmer’s trammer for the grass.

The coil with the button is snapped in the corps of the trimmer’s trammer for the grass

The replacement of the fishing line was successfully made. In this case, you need to install it back on a trimmer for grass and you can proceed to the span of grass.

Sources:

https://1-tools.ru/svarka/STIHL-fs-38-kak-zamenit-lesku.html
https://101benzopila.ru/zamena-leski-v-trimmere-STIHL-fs-38/
https://101benzopila.ru/zamena-leski-v-trimmere-STIHL-fs-55/
https://veloelektro.ru/zamena-leski-v-trimmere-STIHL-fs-55.html
https://drillzone.ru/svarka/kak-zapravit-lesku-v-trimmer-shtil.html
https://101benzopila.ru/kak-namotat-lesku-na-motokosu-stil/
https://simsvarka.ru/abrazivnyj/katushka-dlya-trimmera-shtil-fs-38.html
https://drillzone.ru/abrazivy/katushka-dlya-trimmera-shtil-fs-38.html
https://drillzone.ru/izmerenie/STIHL-fs-38-kak-zamenit-lesku.html

Lawn Mowers coil, lawn, refuel, stihl