How to start a cold single axle tractor. Power tillers with electric starter can be started immediately after turning the ignition on.
Preparing your power tiller for winter
Proper technique preparation before the winter period is critical for extending the service life of an existing power tiller. Many beginning farmers make big mistakes in this case, leaving the machine to winter in unsuitable conditions, or trying to start it in sub-zero temperatures without prior preparation. As a result, the main mechanisms of the machine are subject to increased wear and tear, and inevitably break down at the most inopportune moment.
The advantages of a modern power tiller are its versatility and high performance. If you have the proper attachments, your power tiller can be used extensively in winter to clear large amounts of snow and perform other everyday tasks.
However, improper use of a power tiller in winter, especially its incorrect starting, significantly reduces the service life of the main mechanisms of the machine. What to do. To avoid typical mistakes when starting a “cold” power tiller?
The first thing you need to know is what type of cooling system is intended for. Machines, equipped with an air system, are easier to store and start in winter. they do not need a quickly freezing antifreeze and a constant check of the radiator. At the same time, the air cooling system has a disadvantage. the engine with it heats up faster, and thus cools down faster, which will not allow for long breaks when working in winter.
Many power tillers need to have their engines pre-insulated for winter operation. For this purpose, both branded covers and various improvised means. blankets, plaids and other fabric products can be used. It’s especially important to make sure they’re well insulated when it’s freezing, up to.20 ⁰C. If the temperature does not drop below 5-10 ⁰C, you can skip this step.
The place in which a single–axle tractor is stored also plays an important role. If you plan to use your machine extensively in winter it is best to use a heated area. a garage or other attached building.
If you use your power tiller extensively in winter it is extremely important to take care of the oil in the gearbox. synthetic oils are better for use in winter, because they retain their most important properties longer at sub-zero temperatures than mineral oils. In any case, it is best to use thicker oils, which do not thicken as quickly in freezing temperatures.
If you follow all these rules, it will be easy for the owner of a single–axle tractor to start his machine. Start the agricultural machine in winter in the same sequence as at any other time of the year. The only difference is to let the trimmer idle for at least 15 minutes. during this time its engine will warm up and be fully ready to work. To learn more about starting a power tiller in winter, watch this video.
How to start a single axle tractor correctly?
How to start a single axle tractor at the first start and do not damage the equipment? Never ignore the owner’s manual. The manufacturers always explain the necessary information in them in an accessible way.
In general, there are 3 basic rules you should follow to start your power tiller safely:
- Check that the fuel system levers are securely fastened and move smoothly. The throttle and clutch cables and levers should move smoothly so you can feel them when you drive. You should also pay attention to the steering wheel adjustment.
- Check the oil level (in principle, this should be done before each start). Some models have built-in sensors and will not start automatically if the amount of lubricant is insufficient. Other models are more prone to damage in such a case.
- Check fuel availability. Only fill your machine with quality fuel. this will extend the life of important parts of the machine and increase productivity. Pay attention to engine type. models with a 2-stroke engine need a special fuel mix, which proportions are written in the manual.
Gasoline and diesel engines have some peculiarities that you should take into account when starting. Gasoline-powered airplanes and gensets,
Yamaha Fzs Bs6 fi starting problem fuel pump cheking video#mrsamar123
the engine should be started according to this algorithm:
- Turn off the fuel tap;
- The choke must be set to “Start” mode (Choke);
- with the ignition off, turn the kickstarter several times;
- turn on the ignition, start the machine and move the choke lever to the “Run” position.
Rules for starting the engine without a starter
Engine operation is a complicated technical process, which is responsible for several assemblies in the car. One of the devices that provide the conditions for starting is the starter. This mechanism drives the motor directly and is as important as the ignition or clutch system.
2015 Volvo VNL Day Cab Single Axle (365HP)
Important! Starters are some of the most vulnerable parts in the system. They often break, including in the middle of the season when there is a lot of work. The engine can also be started without it, which saves time for urgent repairs.
The stages of starting a motor in the absence of a starter include:
- Dismantling the defective part.
- Fix a strong rope in the hole on the round iron component, which is located at the place where the starter is installed.
- A rope should be wrapped around this whisk several times (about 4-5 turns), leaving the end about 40 cm.
- The piston is pushed upward, the decompressor is released and the rope is jerked sharply toward you.
Though it is possible to start the power tiller without the starter, do not use it in this way all the time. The following recommendations are for emergencies that require the vehicle to be in working order. But don’t wait too long to repair it. you need to order a new starter as soon as possible. Parts for the single axle tractor are available on the website. There are several kinds of starter motors for different models of special-purpose machines.
Any technique, including power tillers, is prepared for winter according to certain rules. The preservation of the machine begins with its thorough cleaning. Do not leave the product all covered in dirt and earth. After cleaning you need to thoroughly dry everything, because moisture can spoil parts, on which there will be rust.
Inspect all parts for wear and tear and general serviceability. Replace with new ones if needed. If there is water on the elements, it will simply freeze in winter and ruin the entire system. Do I have to drain gasoline and oil?? With gasoline is very simple. you just need to drain it or pour a new one. But with oil will be more complicated. It should be replaced with a new one or filter out the old one, if there is not a lot of sediment in it. Do not leave your equipment without oil.
All cutting parts of the tool must be sharpened carefully. Check the power cord and replace it if necessary before spring arrives. With these recommendations, you are unlikely to have problems with the technician in the spring.
Block: 3/5 | Number of characters: 969
How to start the cultivator. the right order of actions
Often the household equipment does not start due to ignorance of its owner of the correct procedure when starting. In this case it is necessary to carefully read the operator’s manual of the cultivator. If it is not available, you need to follow the algorithm, which is suitable for most models.
To start the power tiller, you need to perform the following actions:
- First it is necessary to move the fuel cock lever to the “Open” position;
- Then you need to close the throttle valve;
- The ignition lever will then need to be moved to the “Open” position;
- Next, the gas lever should be moved slightly to the left side;
- Then you should gently pull the starter lever until you feel resistance. Immediately after that the lever must be returned to its original position, and sharply pull it;
- The engine of the cultivator will start. Wait approx. 2 minutes for the engine to warm up. As the engine warms up, you should gradually open the throttle valve;
- Adjust the throttle lever for optimum engine RPM.
After completing all of the above steps, the farmer can begin to use the cultivator. To stop the engine set the lever of the fuel cock to the “Off” position.
Do you have to drain the gasoline from the power tiller in winter??
Carefully prepare the fuel tank for winter. This is where experts differ in their opinions: some say that the tank should be dried by draining the fuel completely, while others, on the contrary, advise to fill it completely.
In the first case, corrosion can still appear, because it can happen that you have not fully drained the fuel tank. However, if it is completely filled with fuel, as in the second option, then the probability of a fire increases, and it is already much more serious and dangerous problems. We recommend that you follow the instructions and do not risk your life or your property.
Why the power tiller does not start?
If you have difficulty starting the agricultural machine, the first thing to do. is to check the fuel system.
Most often, the main structural causes of farm cultivator malfunction are:
- clogging the air filter. as a result, the element does not pass purified air, which the carburetor necessarily needs for fuel enrichment;
- defect in the fuel tank lid or housing. this causes fuel leakage;
- Clogging in the direct fuel supply duct. as a result the fuel does not reach the cylinder of the internal combustion engine;
- Breakdown or violation of the carburetor settings. because of this, the fuel will not get into the engine in the amount required for proper operation of the agricultural machine.
If the used cultivator won’t start after all these troubleshooting, then it is necessary to check the spark plug carefully. An improperly prepared fuel mixture can cause it to become clogged with oil, which will dry out and prevent spark formation. If that happens, then the operator needs to clean the spark plug from carbon deposits, wash it with clean gasoline, thoroughly dry and screw it back in. After that you need to try again to start the engine of the agricultural machine.
In some cases, when inspecting a cultivator spark plug, users find that it is completely dry. This indicates a lack of proper fuel supply to the factory combustion chamber of the engine.
In order to resume feeding, it is necessary to:
- Completely drain the old contaminated gasoline from the tank;
- Thoroughly flush the removed fuel reservoir;
- Flush and dry the fuel filter;
- Clean the hose through which the fuel comes;
- Flush the regular jets integrated carburetor;
- Fill in fresh fuel;
- Open the stock fuel tap and flush the remaining tubes.
In some cases the farm tiller does not start due to factory defects or typical breakdowns in the ignition system used by the manufacturer. The main cause of the malfunction may be the built-in alternator, the factory spark plug or its outer cap, and the high-voltage cable.
An equally common problem with the factory ignition system of the cultivator in use is a weak spark. The first thing to do in this case. is to check the original electrodes and the factory set gap between them, using a special dipstick. Gap greater than 0.8 mm requires the insulator to be cleaned of dried-on carbon deposits.
Another common cause of failure of agricultural aggregates is the failure of parts of the integrated piston group. During operation the valve, the rings and the cylinder become very hot and subject to friction. It is these parts that are responsible for compression, so in case of their wear the compression ratio inside the internal combustion engine cylinder will be significantly reduced.
The owner of the power tiller must constantly monitor the condition of the intake and regular exhaust valves. In operating condition, they should be as close as possible to the factory seats. If this does not happen, the parts must be replaced.
Another reason why often the farm cultivator does not start is the accumulation of soot on the inner walls of the built-in metal muffler. If they are badly clogged, the exhaust gases cannot escape and will accumulate in the engine compartment of the agricultural machine. A thorough cleaning of the muffler will help solve this problem.
Starting the power tiller after winter
These machines tend to start badly after wintertime. The machine’s ability to work properly after winter is primarily affected by conditions in which it is stored during the cold season. If the machine spends the winter in a cold and wet garage, it can cause serious problems.
Before you start your power tool for the first time this season it is a good idea to change the oil and fuel. Also check that the fluid specifications match the ambient temperature. It is also recommended that you read the instructions again to make sure all the ratios are correct.
It is very likely that the single axle tractor will not start immediately. It is normal to let the parts warm up. The single axle tractor also needs to be warmed up after the engine has started. Over the winter, the fuel may have thickened, so it is better not to start using the machine intensively right away.
Where to store: options and necessary conditions
A shed or equipped utility unit is on the backyard territory of almost every dacha owner. These storage locations are the most common. The main conditions for storing gasoline equipment in sheds or outbuildings. low humidity and stable temperature without sudden jumps.If the room is insulated, it will be an additional plus.
Another place to store gasoline equipment. the garage. You should not place the equipment close to the car, as well as when hanging it, you need to make sure that if it falls, it will not hit the car. And where do you store gasoline equipment in the winter?
This method is not very popular in Russia and former Soviet countries. But if there are no other options, it is possible to find a company that provides these services.