How to start a single tractor in winter Lifan. Operation of equipment in the cold

22nd February 2023

Correct launch of a walk.behind tractor: First, after winter and without a starter

Operation of garden and searry technology begins with its launch. The same.based tractor is a design that provides a complex fuel system and engine. At this stage, any error can cause a breakdown breakdown, a decrease in its work and the life of operation. Depending on the model of the device, its type of engine and the season, the launch includes its characteristics. Knowledge of basic rules and recommendations will make the start of the walk.behind tractor high.quality, and do not damage the unit.

In order to put the equipment into operation, several rules should be fulfilled:

Check the amount of oil. Even if when buying it was assured that everything is flooded, you must definitely make sure that the level of technical fluid in the system is sufficient. Some models of motoblocks are equipped with sensors that respond to a lack of oil and simply do not allow to start a motor. But such an option is not characteristic of everyone, there is a technique that can be launched, but this threatens with breakdowns.
Refun with fuel. It is necessary to take into account the recommendations to a certain model. Gasoline for some will need to dilute. Proportions are indicated in the instructions for the technique. If the one.axle tractor is on a diesel engine, then you need to take into account its type according to the time of the year. Summer DT flooding in winter can provoke a driving fuel hoses, which will operate the machine impossible and cause the need to repair.
Check and configure the compounds. Clutch, steering, gas. they need to be adjusted so accurately as to ensure the smoothness of switching.

start, single, tractor, winter, lifan, operation

Important! New equipment is always supplied with the instructions for the manufacturer. It usually indicates the main recommendations for the use and maintenance of the machine. Therefore, you should first familiarize yourself with the instructions for a specific model and only then proceed to the direct launch of the walk.behind tract.

Description

PROFI motor blocks are SHENLI products. A series of motoblocks is an independent technical branch, in the model range of which many units of motorcycle equipment are represented. all motoblocks of the pros have different power, have a certain set of technical characteristics. Profi 1800

Profi. a separate direction of motoblocks, they belong to the class of heavy motor vehicles, but are not intended for professional use. Their purpose is domestic. Can be used for auxiliary work on the site, for example, for the transportation of a crop, collecting garbage, cleaning territories from snow.

Profi 1900

The PROFI brand appeared after the STENLI motornote enters the SGN market, around the late 90s of the 20th century due to the demand for universal medium-weight motoblocks, which made it possible to make such a technique more accessible for a wide range of consumers.

Why it is necessary to preserve?

In no case, the same tractor can simply be left in the cold garage before the heat. Canned, stored carefully and correctly. In the worst case, after melting snow, you simply cannot start the unit. Simple recommendations for the storage of a walk.behind tract in the winter will help in this matter to prevent mistakes.

Pay attention primarily to the engine with the gearbox. We change the oil. the previous one can also be used, but only under the condition of “suitable” condition and filtering.
Cleaning air filters in good faith and pour engine oil.
We unscrew the candles, add the oil to the cylinder (approximately 20 ml) and “manually” scroll the crankshaft (literally a couple of revolutions).
We carefully clean all parts of the walk.behind tractor from the accumulation of dust and dirt (do not forget about the most inaccessible places). Next, we cover the body and spare parts of special equipment with a thick layer of oil, which will protect against corrosion. Sharp edges we sharpen.
If the one.axic tractor is equipped with an electric steamer, then we remove the battery during winter storage. And also do not forget about its regular exercise throughout the “frosty period”.
We cover the unit, or rather, its painted parts, polish. This will help protect the product from the decay process. It should be noted that the polish is applied only to the clean unit, otherwise there will be no help from it. With the onset of spring, the coating layer should be washed off.
Do not forget to open a fuel supply tap for a couple of times a month and pull the starter handle 2-3 times 2-3 times.

Preparatory stage

So, you are the owner of a new walk.behind tractor to care for your garden, garden and even a personal plot. The first thing to start with is to check the oil level. Even if you are sure that it is enough there or you were assured in the store that it is in full, you still need to check. If the oil is not enough, you can simply ruin the engine. Also, the car may not start if the oil has been flooded for a long time and has managed to deteriorate. Some engines models, such as Subaru or Lon Chin, have a special sensor, which just shows how much oil in your technique.

After that, it is necessary to fill in the fuel. In the operating instructions, you will find information about which gasoline is suitable for your motoblock model. You can also clarify this information from sellers. Another important point applies to two.stroke engines, where gasoline must be diluted with oil in a certain proportion.

Only after that can you proceed directly to the inspection of the entire walk.behind. That is, you must check all the units, fastening the steering wheel and wheels, the clutch and gas cables, and so on.

Correct launch of a walk.behind tractor: First, after winter and without a starter

The first step in the operation of any equipment is its launch. In the case of such a complex device as a single tractor, already at this stage you can cause damage to the machine, which will affect the quality of work and operating time. The correct launch of the walk.behind tractor will avoid many malfunctions. And, accordingly, will make it possible to save time and money on the repair or replacement of spare parts.

Before the first launch of a walk.behind tractor

If you purchased a new car, then first of all you need to carefully read the instructions for operation. This step must not be missed, even if you used motoblocks earlier. the instructions contain the most accurate information on how to start a single tractor for a particular model.

Check the oil level. Some machines have special sensors that do not allow the engine to start if it is not enough oil in it. Other models can be made with insufficient level of technical fluid, but this can cause great damage to the machine;
Pour fuel. In some models, gasoline needs to be diluted. The proportions are written in the instructions. You also need to be neat and with diesel fuel. The instructions should indicate what type of fuel is used at a certain temperature. The use of summer fuel in the winter season can lead to clogging of fuel lines;
Check the connections and configure them. Gas, clutch and steering wheel must be adjusted so that they move smoothly.

How to start a single tractor correctly?

To launch a gasoline walk.behind tract, it is necessary to first transfer the lever lever to the “launch” position. After that, you need to open a gasoline crane and pull the starter several times. Then you can turn on the ignition and download the starter one more time. At this stage, the car should start. It is enough to turn it on in models with an electric starter and start the engine.

Diesel motoblocks start in a slightly different way. First of all, you need to get rid of the air in the fuel line. To do this, open the fuel valve, and then unscrew the supply connection up to the nozzle. When unscrewing the connection, you need to wait until the fuel flows from it. After this procedure, you need to open all the taps and transfer the gas to the middle position. Squeeze and pump a decompressor several times, holding it with a finger. Next, return it to its original position. After that, press it once again and pull the starter. The same.based tractor should start.

Starting engine without starter

Quite often the first to fail. And this can happen at the most inopportune moment. In order not to waste time and money for the full replacement of the part, you can start the engine without it.

To launch a walk.behind tractor without a starter, just perform the following steps:

Remove a broken part;
Find a strong rope about a meter long (can be removed from a broken starter);
At the place where the starter was, you will find a round metal part. On one of its walls there is a special hole. Pass the rope into it and fix it with a knot;
Wrap the cable around the part several times so that its balance is about 40 cm.

Launching a walk.behind tractor after winter

Such machines tend to start poorly after wintering. First of all, the working capacity of the walk.behind tractor after winter is affected by the conditions for storing equipment in the cold time. If the car winter in a cold and cheese garage, then this can lead to serious problems.

Before the first in the season, it is recommended to change the oil and fuel with the launch of a walk.behind tractor. It is also necessary to make sure that the operational characteristics of the technical fluids used correspond to the ambient temperature. It is also recommended to read the instructions again to comply with all proportions.

There is a great probability that the unoic tractor will not immediately start. This is normal, you need to give the details to warm up well. In addition, it is necessary to warm up the one.axle tractor and after the engine starts. During the winter, the fuel could thicken, so it is better not to immediately intensively use the machine.

Recommendations for launching individual motoblock models

To start the uniform tractor of the Neva brand, you need to take the following steps:

Translate the ignition toggle switch to the ON position;
Close the air damper and open the benzovran;
Put the gas handle on ¾ from the maximum;
Pull the starter cable;
Open an air damper (in cold weather it is better to open gradually for a minute).

To start the machine “Patriot”, follow the following actions:

Bring the gas handle to the maximum position;
Several times pull the cable for purging, and then sharply and shortly. to start the engine;
Adjust the gas handle.

You can start the Unoa Tractor of the Ural brand in the following way:

Put the gear handle in a neutral position;
Open Benzokran;
Close the throttle almost to the stop and cover the air damper (if the engine does not cool, you do not need to cover the air damper);
Take the engine using the cord.

HOW TO COLD START HEAVY EQUIPMENT || Different techniques for cold starting heavy equipment

The same.based tractor does not start: the reasons how to repair correctly

Owners of motoblocks, cultivators, motorcycle holders and other mini-equipment, sooner or later, are faced with a typical problem-their working “horse” does not start or start, but stalls when opening the air damn, begins to “shoot”, go out or “sneeze”. To eliminate the annoying obstacle, you need to find out the reason due to which it arises, and then carry out proper repairs. This problem is found on the technique of Chinese, Japanese, Korean production.

The reasons why the unoic tractor does not start, and the ways to eliminate them

The reasons why motor equipment does not start when starting, there are several. These include:

Damage to the carburetor (in walk.in with a gasoline engine);
malfunction of ignition/incandescent devices;
low lubrication.

Когда в мотокультиваторе появляются странные изменения, и его работа становится не стабильной, в первую очередь проверяют карбюратор. In this important node, the fuel mixture (TVS) and dosing it for supply to the internal combustion engine (ICE) are formed in this important node. And if the jackets are clogged, the obstruction of the fuel system occurs, as a result of which the carburetor loses the ability to ensure the launch of the motor. To eliminate the malfunction, repairs of the fuel supply are carried out: the carburetor is partially disassembled, the pump is washed and the nozzles are blown through the fitting fitting.

Sometimes the reason that the uniform tractor does not start is lies in the malfunction of the spark plugs (the spark), which play an important role in the start of the carburetor ICE, or the glow of incandescent, ensuring the launch of the diesel engine. If the devices of the fuse become wet, which happens due to throwing their TVS, then the spark begins to disappear on them. In the absence of sparking, there is no ignition of the fuel mixture, which means that the engine does not start. You can solve such a problem in different ways:

Motorized technique is not started due to the fact that damage to the glow of incandescent occurs. In the diesel engine, fuel ignition comes from contact with red.hot air, which warms up in the cylinder by compressing the piston. This happens without problems when the diesel has already warmed up and the working temperature in it is maintained by the heated walls of the cylinder. But in cold weather, and especially in winter, heating the engine is carried out using incandescent devices and, if they fail, it will not succeed in starting a single.axle tractor.

If, when examining the carburetor engine or diesel, there were no defective candles, but the problems remained, and even accompanied by claps in the silencer, the performance of all the devices responsible for fuel ignition should be checked. The malfunction in them can also be the reason that the one.axine tractor will not start. Diagnostics is best done in the service center, where professionals will find the cause of the damage and competently carry out repairs.

Motics is not started and with insufficient lubricant fluid levels in the motor. Some models are equipped with special control sensors, which, in case of lack of lubrication, prevent the engine. Particular attention should be paid to those options for cars that do not have such sensors. Sooner or later, the level of lubricant mixture will reach a critical value and, if it does not make it up to the norm, this will soon lead to wear of the parts and, as a result, to the overhaul of the engine.

Preparation of the walk.behind tractor for launch

Problems with the start of the motor can arise not only the motoblock and the cultivator who were in use, but also new, just bought in the store. Therefore, before the first time to start a single.axle tractor, whether it is a cascade, a mole, a bison, a centaur, a hoper, a tarn, an eye, a salute, it is necessary to read the guide for its operation, then carefully examine all the connections and, of course, check the oil level in ICE.

To study the instructions compiled by the manufacturer, it is necessary to find out what kind of working cycle the engine has: four.stroke (like Forte, centaur, Lifan, bison) or two.stroke. This is important to know, since for models with a two.stroke engine (like a mole cultivator) you need a special combustible mixture, consisting of a certain proportion of gasoline and oil. Due to the discrepancy between the fuel, the technique will stall, and the candles of the fuse and the fuel pipeline can also suffer, which is fraught with the refusal of the gasoline pump-and this is the direct path to expensive repair in one hundred. You can determine if the fuel is suitable for motor vehicles by smoke. With poor quality of gasoline, it will have white color, as is the case with a strong slope of the machine. If you have bad gasoline, then replace it to prevent breakdown.

Fuel quality is also important for a diesel walk.behind. It does not start in winter or start, but soon stalls if the summer diesel fuel is flooded into its engine. At reduced temperatures, it begins to thicken and clog the fuel stove. In such cases, the risk of breakdown increases. In cold weather, select the corresponding fuel.

Starting of motor vehicles both in summer and in winter should be carried out in a certain sequence. For example, to start the MROT brand motor.cultivator, the following procedure is carried out:

open benzovran;
put the lever lever in the “chock” position (launch);
turn off the ignition and scroll through the motor several times with a manual starter starter;
Run the engine again and the lever is transferred to the Run position (work).

It is not rare that situations arise when the power unit easily starts, but after a few seconds it stalls. In this case, it is necessary to check the patency of the sump, perhaps the reason is that the crane is clogged. then it is cleaned with gasoline.

Starting motorcycle equipment with a diesel engine (such as a bison, cascade, centaur, nonsense) will be somewhat more difficult than mole. The diesel engine is starting with the “fuel” of the fuel line, that is, from the release of its accumulations. For this:

open the fuel supply crane;
unwind the compounds of the fuel.ascending channel until the fuel appears;
twist the joints and blow the nozzles.

Preparation of the walk.behind tractor for winter. what to take care of?

The proper conservation of the walk.behind tractor for the winter is an important topic that allows, if not extended, then at least save the working resource of the unit used in the farm. The preparation of an agricultural machine itself is not a complicated procedure. It is enough to study a number of rules and tips that will help save the unoic tractor and without problems start it after wintering.

By sending an unit for winter storage, you will need:

completely replace the oils in the motor and gearbox of the unit. To do this, in the corresponding tanks for the winter, you will need to fill a new lubricant, or, in extreme cases, filter the old, making sure that there is no sediment in it. In any case, with the onset of spring oil, it will be necessary to replace;
Rinse all the filters available in the design. If the unit is equipped with filters placed in an oil bath, then they need to fill in fresh motor oil;
Many experienced farmers recommend that the motoblock sparkles with the ignition of the walk.in, then pour not more than 20 ml of motor oil into the working cylinder, and manually scroll through the crankshaft of the unit, performing literally a few revolutions;
The uniform tractor for the winter must be washed from dirt, without missing details located in hard.to.reach places. After washing on the body and spare parts of the unit, it will be necessary to apply a thick layer of oil, which will help eliminate the formation of corrosion;
If possible, instead of oil, a special polish with a protective function can be applied to the parts of the walk.behind tractor. it forms a strong film on the metal surface, which will prevent the metal rotting in winter. At the same time, it is very important to apply the product on a clean surface, since otherwise it will not protect the metal parts of the walk.behind tractor;
All the caps of candles and electrical connectors of the unit for the winter need to be lubricated with silicone grease in the form of a spray. it will effectively protect their effects of various environmental factors;
If an electric starter is provided in the design of the walk.behind tractor, then it is best to remove the battery from the unit during the storage in the winter and transfer it to a dry and warm room. During storage, the battery will need to be completely charged several times;
In order to exclude the extent of the rings in the cylinders in winter, you will need to open the motor block fuel several times a month and pull the starter handle 3-4 times 3-4 times.

Adhering to these simple rules, the farmer will provide optimal conditions for storing a walk.behind tractor in winter. With the onset of spring, the unit can be removed from the room, replaced oils, and begin the operation of the unit.

General rules for conservation of technology

Before you leave the technique for the winter, you need to thoroughly wash it, dry each part, examine for breakdowns and damage. The worst thing for any car is left moisture on the details. Water freezes and damages elements in winter.

For safety measures, fuel needs to be drained (however, some owners have a different opinion). But with oil other tips. you can not leave equipment without lubrication in winter. However, it must be changed to new.

All cutting items must be carefully cleaned and sharpened. Hinged joints also require thorough cleaning and lubrication. Also, do not forget to check the power cord. if it is damaged, replace it with a new one before the onset of cold weather and, especially, spring.

General rules for conservation of technology

All cutting items must be carefully cleaned and sharpened. Hinged joints also require thorough cleaning and lubrication. Also, do not forget to check the power cord. if it is damaged, replace it with a new one before the onset of cold weather and, especially, spring.

What they do with gasoline in the winter period?

Frosts require to take the fuel capacity seriously. The opinions of specialists in this case vary. Full fuel drain involves the formation of corrosion. However, with the full tank of the walk.behind tractor, which is stored, the risk of fire increases sharply, which can lead to irreparable consequences.

Motoblocks are widely used in the cold season. A motor-cultivator with a 4-stroke gasoline (or diesel) engine will cope with snow cleaning.

The universal unit is able to perform the following functions in winter:

acts as an additional source of electricity (power adapter);
indispensable for procurement work (garbage removal, firewood harvesting);
removes snow from the territory;
The vehicle for fishing in the winter, and the trailer will serve as a place of storage of fishing rods, tents and sleeping bags.

Many people wonder if it is necessary to heat the oil to take the unit for winter fishing. The engine heating process is necessary when the walk.behind tractor is turned on in the cold. So, consider the features of the inclusion of the unit in the winter period.

Modern motoblocks involve cooling (air). This simplifies their operation at minus temperatures. However, the disadvantage is the rapid cooling of the engine in winter.
There are special covers for a walk.behind tractor for insulation. This will help maintain the “desired” temperature.
In winter, the engine must be pre.heat (diligently watering with hot water).
The oil in the gearbox has the ability to thicken at a low temperature. Therefore, it is best to use its synthetic species or a fairly liquid structure.

How to start a single tractor correctly

Not every technique is launched the same. You need to know how to properly start a single tractor. Launch sequence:

Install the Unoa tractor in a horizontal position. There should be a neutral gear.
Check the amount of oil in the engine and gearbox, fuel in the fuel tank and make sure that there are no subteiders.
Set the gas lever in the middle position, and put the engine to be jambing button on the fuse.
Open a benzran carburetor with a closed air damper.
Take a stable position. Take the handles of the cable tightly, gently jerked the kikstarter. After starting, do not throw them, but you need to carefully return them to the place. The technique may not start right away. In this case, you need to repeat the previous action.
After the one.axic tractor starts, you should wait a few minutes, open the air damper to the end, adjust the level of idle and let the engine warm about 3 minutes. It depends on the air temperature: in the summer it takes less time, in winter. more.

After warming up, you should immediately use a single tractor. It is impossible for him to work at idle for too long. If prolonged per 6 strokes are assumed, the engine must be drowned, and then close the tap at the gas pipeline.

Winter Cold engine tractors start up.

On a note!

Observing these rules, it is possible to significantly increase the life of the equipment.

With the Lifan engine

For the new Lifan walkover, you need to do a run in. This will prepare the machine for work with a high load. With its help, the production and grinding of parts of the power unit is carried out. With the Lifanovsky engine, the running.in must be performed sequentially:

Before starting the engine, check the amount of oil;
pour fuel into the tank;
run the unoic tractor at medium power;
within 1 h. It is necessary to alternately switch the gears to test the car;
perform plowing, cultivation on prepared land or transportation of cargo using a cultivator at medium power;
then you must definitely replace the oil and pour new fuel into the tank.

After that, the unit can be used as usual and at high power. Actions that must be performed for running.in are also described in the instructions. Lifan manufacturer makes high.quality models. They have a long service life, since the one.axle tractor starts with an electric starter.

With a mower

You need to check all the bolts and nuts on the supporting structures. If they are poorly tightened, the details will be in motion and will be quickly widened. For example, the state of the clutch pads depends on this.

On a note!

If they are not fixed, there is a probability of even the appearance of a fire in the fuel system.

There are bolts in the gearbox that hold a drive shaft bar. She can jump out if they are twisted poorly, and the unoic tractor will have to be repaired. If the bolts that fix the hilt are not tightened, the shaft can drop and damage the cutting parts. Staging step by step:

You need to check the amount of oil and fuel in the tank.
Turn the air damper to the “launch” position.
Then click on the switch “Turn on”.
Press and fix the gas button.
Wipe the starter cable.

Do not forget to transfer the air damper to the “open” position. This will help to start the same.based tractor much faster.

With a rope

It is useful to know how to properly start a single.based tractor with a Chinese engine using a rope. To do this, pull the rope at a certain angle. It is necessary to calculate the force so as not to break it.

When a break, the rope is not easy to replace. To do this, you will have to disassemble the half.engine. It is mainly used in old models (“salute”) or new ones that are made in China.

With a suction

Before starting, you need to inspect the body of the walk-behind tractor, parts and fix it if something is poorly twisted. For start:

Bend “antennae”.
Take a drum counterclockwise.
Let go of the spring.
Then combine the fan and drum holes.
Put a launch cord with a handle.
Tie a knot on the drum.
Twist by the rope.

On a note!

With an improper sequence of actions, a breakdown in the checkpoint may occur or jump out the shaft.

How to quickly start a single tractor after winter

In winter, low temperature affects the state of technology. Recommendations before starting:

Inspect the appearance of the machine. If there are defects, they should be eliminated.
Check the amount of oil. If it was not drained, after winter it can freeze.
Clean the car from oil and pour new.
Fill the fuel tank. If a two.stroke engine is installed, do not forget to dilute with oil.
Check the condition of the parts of the machine, bolts, nuts and connections. If they have rust or chips, they must be replaced.

If gasoline is used, the engine will already be 1-2 times, since this fuel is resistant to low temperatures. If diesel is used, you have to pull the starter longer. First unscrew the fuel supply valve, and when the fuel starts to pour, tighten. This must be done to clean the nozzle.

You can start in another way. open all the taps by putting the gas on average capacity. You need to hold a decompressor with your finger, squeezing it. After a few seconds you should let him go and pull it so that he again stands in its original position. They press the decompressor and starter at the same time. This will help the walk.behind tractor get started faster.

The same.based tractor does not start: the reasons how to repair correctly

The reasons why the unoic tractor does not start, and the ways to eliminate them

The reasons why motor equipment does not start when starting, there are several. These include:

Damage to the carburetor (in walk.in with a gasoline engine);
malfunction of ignition/incandescent devices;
low lubrication.

Preparation of the walk.behind tractor for launch

Problems with the start of the motor can arise not only the motor block and the cultivator who were in use, but also new, just bought in the store. Therefore, before the first time to start a single.axle tractor, whether it is a cascade, a mole, a bison, a centaur, a hoper, a tarn, an eye, a salute, it is necessary to read the guide for its operation, then carefully examine all the connections and, of course, check the oil level in ICE.

Starting of motor vehicles both in summer and in winter should be carried out in a certain sequence. For example, to start the MROT brand motor.cultivator, the following procedure is carried out:

open benzovran;
put the lever lever in the “chock” position (launch);
turn off the ignition and scroll through the motor several times with a manual starter starter;
Run the engine again and the lever is transferred to the Run position (work).

open the fuel supply crane;
unwind the compounds of the fuel.ascending channel until the fuel appears;
twist the joints and blow the nozzles.

Why the one.axle tractor does not start

Often, owners of agricultural machinery are faced with various malfunctions. For example, the same.based tractor does not start and shoots. To eliminate the breakdown, first of all, it is necessary to determine its cause.

Then they independently engage in the direct repair of equipment or contact the service center. In this article we will talk about why the same.based tractor is not starting and how to fix it.

Causes and methods of elimination

insufficient amount of engine oil;
problems of incandescent and ignition devices in the performance;
malfunctions in the node of the power supply system of a mini-tractor with a gasoline engine.

Often the reasons for the fact that the uniform tractor does not start in the improper operation of the spark plugs or incandescent. This is due to the fact that sparks disappeared due to excessive humidity on the spare parts. It occurs as a result of throwing heat.eating assembly.

If there is no sparking, then the engine of the walk.behind tractor does not start. How to solve the problem:

If the diesel uniform tractor does not start, and the candles of incandescent are still functioning properly, then they check the work of all devices that are responsible for the ignorance of combustible substance.

Manufacturers recommend taking diagnostics in the service center so that the master determines the cause of the malfunction and conduct a full repair.

How to prepare a single tractor for launch

What to do in the first place, when the one.based tractor does not start? Regardless of the modification of agricultural machinery, first of all, the owner must familiarize himself with the instruction on operation, and then carefully check all the devices and connections. Also, we must not forget about checking the level of lubricant in the ICE.

The manual indicates the necessary information for repair, such as the description of the engine. The motor can be two- or four-stroke.

For models from the first category you will need a special combustible liquid, which contains gasoline and engine oil. If you use inappropriate fuel, then the engine will work with interruptions.

To determine the appropriate fuel, you need to pay attention to the outgoing smoke. When using high.quality gasoline or diesel, it will be white. Also, the engine does not work if in winter the diesel fuel was poured into it, designed for warm weather.

How to start a gasoline engine

The launch of a gasoline mini-tractor is carried out in a specific order:

Open the fuel valve.
On the carburetor, the lever of the suction is transferred to the launch position.
Turn off the ignition and a couple of times using a mechanism with a special cable, scroll the motor motor.
Once again they start a motor, after putting a lever in the job position.

Launch of a diesel engine

How to start a machine that works on diesel fuel:

Open the fuel valve.
Unscrew the channel connections until the fuel starts to flow.
Twist the parts and blow the nozzles with compressed air.

How to start a single tractor after winter

If the motor unit is launched after a long.standing one or in the summer after the winter, then the following actions are performed:

In addition, before starting, it is necessary to check all the connections, clutch, mechanisms and nodes. Next, we will talk about what to do if the one.axle tractor does not start.

Do.it.yourself motoblock repair

Agricultural machinery, like other devices periodically breaks. Therefore, it is important for the owner to be able to repair the equipment based on the size of the walk.behind tractor, with your own hands. However, with an endless guarantee, it is better to contact the masters in the service center, as they will repair for free.

The fuel system is damaged if the motor:

To carry out repair of motor blocks, first check the condition of air and oil filters. With small clogging, they are washed or purged with compressed air. If there are strong dirt on the details, then the old spare parts are replaced with new.

At the next stage, they analyze the carburetor, flushing all components of a special cleansing agent. They also carefully clean the fuel valve, tank and a piston system of gasoline.

When all the details dry well, they are installed in the reverse order.

Next, screw the crankshaft, while the piston should walk freely, and the valves function uninterruptedly. Then they are refueled with new engine oil, the engine is started and left to work at idle for some time. It is important to check whether the combustible substance to the cylinder comes.

What should be done?

Start searching for malfunctions from the power supply system. Check:

If no malfunctions were found, you can proceed to checking the ignition system. First, make sure that the fuse is working. Perhaps one of the terminals disconnected, control lamps went out.

Check if there is a spark. To do this, remove the tip of the spark plug and insert a small wire into it, turning on the ignition. If the chain between the electrodes functions normally, a spark should appear. If it is not, then most likely the ignition coil failed. It is also possible that the device capacitor is broken. It is very difficult to replace the ignition coil and the capacitor yourself, so if such a breakdown is detected, take the unit immediately in the service center.

If when checking the ignition system, you revealed a candle malfunction, we recommend that you clean it from soot, dry it, and then try to work with it again. If this did not bring positive results, it is best to install a new candle. Very often, such measures lead to the complete restoration of the aggregate performance.

No spark on the walk.behind tractor

This malfunction is directly related to the breakdown of the ignition system. The breakdowns in the ignition system include malfunctions in the work of magneto, generator, wiring, cap and spark plugs. If a spark is gone or it is weak. the reason is only in the cap and candles. First of all, remove the candle, evaluate its condition. If you need, rub the carbon on her and “fry” her over the fire (if there is no way to momentarily replace it with a new one).

Set the candle in place and try to start a single tractor again. If there are still no sparks, check the contact of the cap with the central electrode of the candle. The gap between the cap and the electrode is checked by a special probe and should be 0.8 mm.

A few words about how to avoid such situations. First of all, always clearly follow the recommendations specified in the operating instructions. If you adhere to them, your one.axle tractor will last much longer.

Also, in order to avoid problems with the launch of a walk.behind tractor, it is important to know which engine cycle of this model (which is also indicated in the instructions). For example, Neva’s motor blocks (MB-1 and MB-2, which are most often equipped with a Subaru engine), bison, salute, agro, cascade are equipped with a four-stroke engine. And the motor blocks of the company Mole Two.stroke. The value of this information for the owners is that it indicates how to properly refuel the technique of fuel. For models with a 2-stroke engine, you need to prepare a special combustible mixture for which gasoline and oil are mixed in a certain proportion. For motoblocks with a 4-stroke engine, oil and gasoline are poured separately. But do not forget to follow their quality also!

Also, you should always remember the proper order of launching your walk.behind tract. For example, for the Motoblock Mole or any other unit with a gasoline engine, the launch is carried out in the following sequence:

Open gasoline feed crane.
Set the fuel leaks in the “launch” mode (Choke).
The engine when the ignition is turned off several times, is worked out by a cup starter.
Get a single tractor and switch the fuel lever to the “work” position (Run).

With diesel engines of the Neva, bison, salute, cascade or agro, the situation is a little more complicated. First you need to steal the air from the fuel system. To do this, open the fuel supply valve, spin the joints of the fuel hose until fuel appears, tighten the connections and blow the nozzles. If, after the manipulations made, the same.based tractor did not start or start, but thick white smoke comes from the silencer, you need to urgently replace the oil.

After prolonged diesel, diesel should be launched according to this algorithm:

Open a gasoline crane.
Check the presence of lubrication.
Turn on the ignition.
Slightly twist the handle of gas, no more than half.

We also offer you to get acquainted with the video on how to properly run the single.axle tractor:

Features and rules for launching a walk.behind tractor with step.by.step instructions

After preparatory measures, making sure that the oil is flooded, gasoline or diesel fuel corresponds to the model of the walk.behind tractor, all nodes are fixed and are in good condition, we start the unit.

How to run the same.based tractor, you can find out by looking at

Unine.based tractor with a gasoline engine

Open a fuel tap tile. In this case, the lever of the fuel leaks must be installed in the start position, and the ignition should be turned off.
Several times (2-3 will be enough) pull the launch cord.
Turn on the ignition and pull the starter cable again.
After the engine has started, you should quickly install the lever lever to the work position.

If there is an electric starter in the motor block, you just need to turn on the ignition and press the engine start button.

one.axle tractor with diesel power plant

If the technique is new, then its entire fuel system is ascended. To blow it and start the engine, you need to perform a certain sequence of actions:

Unscrew the fuel supply crane, gradually unwinding each connection of the fuel line from it. When the diesel fuel reaches a certain connection, immediately tighten it.
As soon as the fuel enters the nozzle, you need to open all the available cranes and put the gas lever in the middle position.
Press your finger and pump a decompressor several times until the fuel reaches the cylinder;
Release the decompressor and pull it until the moment he stands in the regular place;
Click on the decompressor again, and without supporting it, sharply pull on yourself a launch cord.

This is a general algorithm that shows how to properly start a single tractor of any brand, it is applicable to almost all models, but below we will analyze step.by.step launch algorithms for the most popular motorbace.cultivators.

To facilitate the first launch procedure, you can remove the wedge belts. Without load, the engine is easier to start.

How to start motoblocks of popular brands

On the domestic market, models of various manufacturers are represented, which have their own design features, so the launch of motor vehicles is carried out in different ways. This should not be forgotten, since the wrong procedure can lead to the failure of the equipment and will require serious money for repair.

Let’s see how to start the one.based Tractor of the company Neva.

Currently, the closed joint.stock company Red October. Neva produces Neva motor blocks with the power plants of stamps Zongshen, Briggsstratton and Yamaha.

Consider the procedure for starting these engines separately.

Switch the fuel valve to the ON position (VKL).
The lever of the air damper should be in the off.
Switch the throttle lever to a certain position.
Get firmly by the handle of the manual starter and begin to slowly pull the cable until you feel resistance.
Pull the starting cord abruptly on yourself.
After the engine is launched, the air damper should be slowly transferred to the ON position (VKL).

To launch the Briggsstratton brand motor:

Move the lever of the stop switch to the ON position (VKL).
Switch the throttle lever to Fast position (quickly). The engine is controlled only in the FAST position (quickly).
Move the air damper control lever to the CLOSED position (closed).
Set the fuel feeding to the Open position (openly).
Take the handle of the starting cable tightly and slowly pull until you feel resistance.
Dramatically pull the starting cord on yourself, the engine should start, otherwise you need to repeat the twitching by the cord.
When the engine warms up, move the air damper control lever to the Open position (openly).
Turn the fuel valve to the Open/ON (OL) position.
Move the air damper to the stop.
Turn the throttle in the direction of the ON position (VKL).
Set the engine switch to the ON position.
Slowly pull the cord starter until you feel the gear gear.
Pull sharply by the cord.
Return the air damper to its original position and set the throttle in the desired position.

We also recommend reading in more detail about Neva MB-2 motoblocks, this article contains all the most popular models today, as well as which of them is better to choose for purchase and why.

Unine.based Brait tractor

Before starting the unoic tractor, make sure that the clutch is turned off and move the switching lever to the neutral position to avoid a sudden jerk of a walk.behind tract during engine start. The clutch turns off by clicking on the lever, and turns off by release.

Move the fuel tap to the ON position (OB) and make sure that there is no fuel leakage.
Close the air damper (lever in the Close position). Do not close the throttle if the engine is warm or the air temperature is high.
Move the engine starting switch to the ON position (VKL).
Set the gas handle to the full gas position.
Small the starter’s handle smoothly until you feel resistance, and then pull it with moderate force.
As you warm the motor, gradually move the air damper lever to the ON position (openly).

Now you know how to start a BRAIT motor.cultivator correctly.

The uniform tractor of the Urals

Before starting, make sure the air filter is completely clean. Be sure to inspect the spark plug, since one of the shortcomings of the technique of this brand is the flow of oil from a separate tank to the engine cylinder.

Move the fuel valve handle to the ON position (VKL).
To start the cold engine, move the air damper lever to the Closed position (closed). To re.start the hot engine, leave the air damper lever in the Open position (openly).
Put the gas lever (on the engine or on the steering wheel) from the Min (min) position, approximately 1/3 of the course in the direction of the Max position (Max).
Transfer the switch (on the engine or on the steering wheel) to the ON position (VKL).
Pull the launch of the starter launch cord until you feel significant resistance, then return to its original position, and then pull the handle energetically.
After the engine starts and works a bit, transfer the air damper lever to the Open position (openly), and warm the motor at minimum speed for 3-5 minutes.

The same.based Patriot tractor

Now let’s see how to properly start Patriot motor blocks. By the way, before starting, check the correct assembly of the cultivator, stretching drive belts and guide rollers, sedatives.

Install the switch on the steering wheel to the ON position (VKL);
Open the fuel supply crane (transfer the lever to the extreme right position);
The lever of the air damper should be in the extreme left position;
The gas lever is installed in the middle position;
Stretch the starter handle until the resistance appears;
With a sharp but not long jerk, pull the trigger on yourself;
After the engine warms up, translate the air damper lever to the extreme right position.

As you can see, all the motoblocks start approximately the same, there are small differences, but in general it makes no difference if it is an old cascade or modern Lifan.

Thus, adhering to the rules and recommendations for the launch of the power plant from the manufacturers, you will extend the life of your walk.behind tract and you can avoid the cultivator breakdown. Also regularly carry out preventive inspections and maintenance of the unit. This will allow timely detecting a slight malfunction and eliminate it in time.

Sources:

https://gp-prsmah.ru/servis/kak-zavesti-motoblok-bez-startera.html
https://lizing-spectehniki.ru/motobloki/kak-pravil-no-zavesti-motoblok.html
https://avto-mekhanik.ru/sovety/kak-zavesti-motoblok-posle-zimy-lifan.html
https://gp-prsmah.ru/brend/kak-zavesti-motoblok-zimoj.html
https://kalibrtractor.ru/spetstehnika/kak-podgotovit-motoblok-k-zime.html
https://topkarting.ru/kak-pravilno-zavodit-motoblok.html
https://veloelektro.ru/motoblok-ne-zavoditsya-zimoj-prichina.html
https://lizing-spectehniki.ru/motobloki/pochemu-ne-zavodit-sya-motoblok.html
https://benzopilok.ru/motobloki/pravila-i-osobennosti-zapuska.html

Articles lifan, operation, single, start, tractor, winter