How to start a STIHL chainsaw correctly

29th October 2021

How to start a chainsaws with a decompression valve

Before starting a STIHL chainsaw with a decompression valve, you must turn it on. It should be noted that there is no decompression valve on the STIHL 250 saw.

After the first flash has passed, the valve will be set to normal operation, respectively, after the engine control lever is set to the open air damper position and starting continues, the decompression valve must be pressed again.

The valve operation is schematically shown in the figure below.

In fact, the valve does not make starting faster, it just simplifies the process and makes it more comfortable, because for during launch, a person will have to apply significantly less effort.

A saw with a decompression valve, whether the engine is cold or hot, must be started using the valve to relieve the cranking force of the engine. This will significantly increase the service life of the starter and reduce the number of torn laces, since it is installed on chainsaws with a large cylinder volume and, accordingly, compression.

How to start a STIHL chainsaw

All STIHL chainsaws are equipped with two-stroke engines, the cold start of which has a similar algorithm. But there are models on which additional equipment is installed, allowing you to start the saw without excessive efforts. For this reason, the algorithm for starting them may differ slightly.

Let’s take a look at how to start a regular saw and how the process differs from starting a modified model.

How to start the saw after long periods of inactivity

I can’t start the chainsaw after a long period of inactivity. Such Комментарии и мнения владельцев can be found on the forums dedicated to the repair and operation of saws. Let’s figure out how to start a chainsaw after a long period of inactivity.

The fact is that a successful start after downtime must be taken care of in advance and the saw should be properly prepared for storage. According to the manufacturer’s instructions, before storing, it is necessary to drain the fuel from the tank, then start the engine and burn off the fuel in the fuel system.

Preparation is necessary so that during storage, the carburetor membranes do not stick together. Performing this simple operation will allow you to successfully start the saw after long-term storage.

It is much easier to start the chainsaw six months after idle time, if just before starting, through the spark plug hole, add 1. 2 ml of the fuel mixture to the cylinder. This can be done with a syringe.

We start STIHL 180

In order to start the STIHL 180 chainsaw on a cold one, you must follow the algorithm specified by the manufacturer in the instructions for the STIHL 180 chainsaw, namely:

Turn on the ignition and set the engine control lever to the lowest position (in this position, the air damper of the STIHL 180 carburetor blocks air from the air filter, and the throttle valve is fully open, thus the fuel mixture is enriched);
Pull the starter handle several times until the first flash passes (the flash signals that the fuel mixture has entered the cylinder and the saw is ready to start);
Set the control lever one position up from fully lowered (in this position, the air damper opens, and the throttle valve remains in the same position as before);
Pull starter and start. The saw will start and run at higher rpm due to the throttle valve being as open as possible. To set the damper to idle mode, you must press the gas trigger and immediately release, the tool immediately normalizes the speed.

The STIHL MS 180 chainsaw, as standard, is not equipped with any additional devices that can facilitate starting.

Tech Chat with Chad. How to start your STIHL chain saw. Season 1 EP 1

Below you can see how to start STIHL 180. The video reflects in detail all the main points, and the author’s Комментарии и мнения владельцев allow you to understand the whole process to the smallest detail.

What happens at the moment of priming fuel with primer, and how it helps to start the saw more efficiently?

At the moment of starting the saw without a primer, several movements of the starter are carried out only so that the fuel pump, under the action of an impulse from the saw crankcase, pumped fuel into the carburetor.

A pump installed in the fuel line allows you to manually pump gasoline into the carburetor without unnecessary movements with the starter. The effect of this action is obvious, the saw will start much faster.

Stihl chainsaw startup instructions

Many owners of gasoline-powered tools mistakenly believe that a hand pump can overly pump fuel into the carburetor and, for this reason, flood the candle. This is fundamentally wrong, since the system is capable of circulating around. Excess gasoline from the carburetor will be directed, through a dedicated hose, back to the tank.

There is no need to use a primer on a hot chainsaw, since there is enough fuel in the carburetor to start.

Getting Started STIHL MS 180 C

The device of this model, in comparison with the previous one, has some differences in the trigger mechanism, but it does not carry any changes in the triggering algorithm. The fact is that the ErgoStart system is installed in the STIHL 180 C, which, due to an additional spring installed in the chainsaw starter, reduces the engine resistance when starting.

We start STIHL MS 211 C-BE

The fuel supply system in the STIHL MS 211 C-BE chainsaw is additionally equipped with a manual fuel pump, which makes it easier to start the chainsaw on a cold.

The instruction for starting this model of the STIHL chainsaw contains one additional point, which is that before starting the chainsaw on a cold one, it is necessary to pump fuel into the carburetor using a pump. Further, the instruction does not differ from starting STIHL 180 and follows the same algorithm.

Starting a STIHL chainsaw almost always follows the same algorithm, except for those cases when a decompression valve and a fuel primer are additionally installed on the chainsaw. These gadgets are designed to facilitate the start-up process and do an excellent job of their functions.

Saw won’t start: reasons and solutions

First of all, it is worth noting the fact that the chainsaw 180 of this manufacturer is one of his best “creations”, but it also has its drawbacks. Actually, which we will now talk about.

STIHL

start

correctly

Naturally, this problem can be solved, but, given the design of this chainsaw, it will not be so easy to do this, since you simply have to completely disassemble the device in order, as they say, to get to the right place. The video shows more clearly:

The main reasons for this kind of malfunction are the carburetor and filter, which could simply be clogged.

In order to exclude the saloon from damaged objects, it is necessary first of all to disconnect the fuel hose from the carburetor itself and actually check if fuel is leaking from it. You must remember that in the process of correct operation of the chainsaw, gasoline should flow out in a dense and stable stream. Also, it is not uncommon for the STIHL 180 chainsaw to not start up hot and actually stall after switching on, or it holds power for a rather short time.

Chapter 9: Starting Your STIHL Chainsaw

In this case, the problem of breakdown lies precisely in the muffler, which can simply be clogged with any deposits that arise through the operation of the device, and which settle during the exhaust process.

Also, a fairly common cause of tool malfunction is insufficient lubrication of the device chain itself. The reason for this may be channels that are simply clogged, or the reason is in the oil line that is leaking.

The power of this model is equal to 2.6 watts. It’s worth noting that this is a fairly significant level of strength, considering that it is not a professional chainsaw. The oil tank has a volume of only 0.145 liters, and the fuel tank. 0.25 liters. The tire measures 350 mm and has a pitch of 0.325 inches.

Briefly about the launcher

The chainsaw is powered by an internal combustion engine. This is a simple device, the design of which does not have any special bells and whistles. It usually works properly even in difficult conditions.

Functioning is provided by structural elements:

Carburetor engine (see carburetor adjustment).
Centrifugal clutches.
Ignition system, in almost all devices contactless.
Carburetor that adds air to the fuel mixture.
Fuel system. Its standard device consists of a hose, filter and gas tank, but sometimes it also has additional parts.
Starter.
Tire.
Chain (see chain oil).
Chain tensioner and brake (see how to sharpen the chain).

How to start the STIHL 180 correctly

How to start a STIHL MS 180 chainsaw. Starting a STIHL chainsaw. How to start a STIHL 180 chainsaw correctly. First start

Chainsaw chain lubrication

Connecting pipes or the connections themselves in the area of the oil pump fittings can also leak.
It happens that the STIHL 180 chainsaw does not start well because of the cylinder, which can be broken. But to determine its condition, a visual inspection is enough. But if even there you find the formation of irregularities and chips, then you can be sure that you have found the cause of the breakdown.
If, by checking, you find that the malfunction is in the candle, then you simply need to unscrew it, and then dry it directly. How to distinguish a copy of STIHL 180 from how to distinguish a fake chainsaw from STIHL 180 But it is worth noting that you cannot pierce it in any case, since you will simply ruin the part, and it will be unusable.

You also need to drain excess fuel from it through a special hole.

In addition, you must remember that direct drying should be carried out for at least thirty minutes, and only after this kind of manipulation can you install it back and actually try to launch the tool directly.

over, there may be such that the expiration date of your candle has simply passed, in which case it is necessary to replace it. Therefore, it is a great advice that it is best to always have a new candle in stock or, best of all, a set. Then you can replace it at any time and actually understand whether it was the direct cause of the device breakdown. Replacing the starter cord on how to properly start the STIHL 180 video chainsaw. over, a weak contact can also be the cause of a breakdown, which actually connects the high-voltage wire and the end of the candle. Also, the cause may be a breakdown of the ignition unit. It is worth noting the fact that in order to eliminate this kind of problem, it is necessary to replace the unit itself, since it cannot be repaired.

Equally important is the excitement of the owners of this model regarding the systematic idling after the first gasoline tanks themselves are empty. But if experts in this field are to be believed, they argue that this kind of situation does not pose any problem. But still, if this kind of process is repeated often enough, then you need to simply reduce the engine speed by using a carburetor screw.

In addition, you can personally clean the muffler itself, since the cause of the malfunction may also be in it. This manipulation is not difficult. A fairly common phenomenon of poor-quality tool operation is the carburetor.

But it is worth noting that it will be best if specialists will repair it, since if you have the necessary knowledge and skills, then you can simply break it down and have to buy a new one.

It is important that even if you found the very cause of the instrument malfunction, this does not mean at all that you will be able to eliminate it yourself. Since there are such breakdowns that can only be corrected by a specialist. If you have carried out a direct manipulation regarding checking and changing the quality of the oil (see oil for the STIHL chainsaw), but, nevertheless, the chainsaw still refuses to start, in this case, you must continue to search.

But if you fully performed all the manipulations prescribed above and did not miss a single nuance, but nevertheless the tool has not yet been corrected, then in this case the problem lies in the group, which is called the cylinder one. But if you still could not “bring back to life” your iron friend, then simply take the chainsaw to a service center, where your device will be repaired.

If you cannot turn on and start the chainsaw

When all actions are performed in accordance with the established order, and the chainsaw does not start work, then there are malfunctions in its mechanism. Usually the cause of this phenomenon is common and easily fixable problems, such as lack of spark, shut off the fuel supply, clogged filter that allows air to pass through. In order to start the chainsaw, you will have to find the cause and take the necessary steps to eliminate it.

Only correct actions should be taken. If a person does not know what to do, there is no need to commit rash acts. It is forbidden to disassemble the device, you need to be especially careful with the carburetor. You cannot unscrew any screws on it, since if its device has caused a breakdown, then it is impossible to repair the chainsaw without professional equipment.

The actions that need to be performed in a strict order are listed. Only during the transition from one measure to another can the exact cause of the malfunction be determined and quickly eliminated without damaging other parts. Algorithm of actions performed in case of failures in the establishment of a chainsaw:

At first it is enough to let the device rest. This is especially true for recently used saws. It is enough to wait no more than 10 minutes, since during this time the mechanism will cool down and in the absence of other breakdowns it will easily start. Sometimes it happens that a candle is poured near the appliance during the establishment. If this unpleasant property has occurred, then it is enough to wait a very short pause and repeat all the steps again to start the engine.
The housing cover is unscrewed from the device to remove the air filter. The process of starting up the device is performed if it is absent. Sometimes the reason for the lack of ignition is that the filter is dirty. If ignition occurred without it, then the reason lies precisely in this. To eliminate these troubles, it is enough to wash the filter under running, warm water and soap, then dry it. It is also possible to replace the old element with a new one.
The spark plug is removed. The spark is checked. If it does not appear, you need to replace the old candle with a new one. Usually this helps and a spark appears, but in some cases there is no spark even when changing the mixture.

This means that the ignition unit is damaged, and the chainsaw needs professional repair. Sometimes there is a malfunction of the ignition unit even in the presence of a spark, therefore, this criterion cannot be followed to eliminate the likelihood of breakage.

When a spark appears when it is not possible to make the device work, you must continue to perform the steps described below.

There are times when a spark appears, but the candle itself is moistened. This is possible if gasoline gets on it. To get rid of it, it is enough to turn the device over so that the cylinder is facing downwards. Then all the excess liquid will pour out. Next, you should check the combustion chamber, for which you need to pull the starter more than 10 times. A candle damaged by moisture can be replaced with a subsequent check of its effectiveness. If it becomes faulty, you can replace this element with a new one. After these steps, you need to try again to activate the device.

Sometimes the candle remains dry. In this case, it is necessary to draw the gas mixture into the syringe and pass it into the cylinder. After that, you should immediately try to start the device. If the reason for the long lack of response to attempts to turn on is debris trapped in the carburetor, then when removing it, there should be no obstacle to the flow of fuel into the combustion chamber. The mechanism of successful garbage collection is determined by the flow of liquid when filling the gas mixture, so you need to fill in the fuel with force, and then almost immediately try to start the device.

The muffler is removed. To do this, it is unscrewed and carefully removed so as not to deform the gasket that delimits it from the engine. It is necessary to try to start the mechanism without using an air filter and a muffler, which helps to exclude breakdowns in these structural elements.

In case of any damage to the cylinder walls, it can be concluded that it will have to be repaired by professional methods or replaced with a new one. Usually, an insufficient concentration of oil in the fuel leads to such malfunctions.

The chainsaw should be started following the standard instructions. If there are any problems with the operation of the device, for example, the chainsaw does not start, it is necessary to quickly eliminate them or take the device for repair, and in order to identify malfunctions and work correctly with the chainsaw, you need to know the features of its design. To learn how to quickly turn on the device and fix breakdowns, it is enough to study the basic range of necessary actions and follow it. Read about how to properly run your chainsaw before starting it for the first time.

In operation of the STIHL MC 180 chainsaw. A problem in the future. Before conservation for the winter, on the advice of mechanics, I dripped 4 drops of engine oil (STIHL) into the hole of the spark plug. twirled the candle. At the moment, I was going to go to the dacha, I decided to take a look at the saw. I pulled the starter, but it does not turn! He turned out the candle, it was in oil, and put it back on. the same thing. He turned it out, turned the starter without a candle. everything is completely spinning. Spinned back. the starter does not turn. What could be?

Rinse the saw with clean, undiluted gasoline, pour directly through the plug hole and slowly turn the starter. Later, drain the fuel and use the newest. After all these manipulations, dry the saw and the candle and only then try to start it. Once you have learned to preserve, then learn and re-preserve, and not just pulled and drove.

Tell me, what is the reason for the starter to jam? STIHL 180 chain saw brand new.

You will not make out you will not know. Maybe the starting cord does not fit well, or maybe somewhere the ebb tide interferes. Shtilev starters are quite reliable and durable. No diseases of a constructive plan are observed, in the main either mud or saturated operation. Once the chainsaw is brand new, bring it to the service under warranty will be repaired.

I saw one peculiarity at my own STIHL MS 180 chain saw: when the gasoline in the tank runs out, the idle speed increases and the chain starts spinning even when the trigger is released. When you press the gas, the chainsaw stalls. This continues for a couple of 10 seconds, later the chain saw stops. On automobiles, I did not observe such a phenomenon, so that when there was a shortage of fuel in the carburetor, the engine speed would increase. Why is this happening?

This is a common occurrence for two-stroke engines. With a decrease in the supply of gasoline to the carburetor, a lean consistency occurs. As a result. an increase in revs, a deterioration in acceleration. This is accompanied by short-term overheating of the CPG. The engine will not disable it, but it will not add health. Avoid running out of fuel from the tank to the end.

There is a STIHL MS180 chainsaw, used in the summer season for the preparation of firewood. In the near future, the reaction of the chain when you press the gas began to disappear, the chain does not turn at all, or in jerks. it is unrealistic to cut. What could be the breakdown?

For a completely new chain and sprocket, the tension should be exactly according to the annotation. so that the lower branch does not sag. and the upper fingers could be removed to the height of the driving link. Then the chain will move fairly freely on the bus. But, the gradual wear of the teeth of the sprocket decreases its pitch. And the gradual stretching of the chain increases its step. and the time comes when the steps of the same sprockets and chains no longer coincide to such an extent that the recommended tension already causes a difficult movement of the chain. In this case, we advise you to slightly reduce the stretch. Right before the appearance of a certain sag of the lower branch. By the way, for the same reason, it is recommended to use a pair or even three chains on one sprocket. Chainsaw STIHL mc 180. a concise overview Petrol saws and Starting the STIHL 180 Chainsaw.

Chainsaw STIHL 180 after starting, when you press the gas, “bungs” and if you start sawing, it stalls. But if you torment with gas for 30-40 seconds, it starts working normally. produced 3 liters of gasoline, the filter is spotless, the oil from the dealer.

If it started not so long ago, then, most likely, something got into the carburetor with bad fuel. Needs to be cleaned.

I would like to purchase this unit. What you need to pay attention to when examining?

Not to mention the engine itself, since it is better to diagnose it in the service, you can look at the rest and get a lot of information. Significant mileage will be evidenced by: Dangling latch of the top cover. (Should lock tightly and not rotate from vibration). A brand new sprocket on a battered chainsaw. When the cover is removed, the movement of the motor relative to the body. Sheared chain catcher and chain damage on the sprocket cover. You can also take a close look at the carburetor from the left in the direction of the direction. the place where the wire rod enters the choke axle lever. In a chain saw that has not been used much, it will be flat, oblong. The longer the saw has worked, the more this hole will be worked out. From time to time it is rubbed through. Under no circumstances should you take a saw that has at least a small free play of the right end of the crankshaft relative to the motor. This is a sign of an imminent half-life of repair.

How many seconds the engine of the STIHL chainsaw should run at idle speed 180 ms before turning it off?

Let it work for about 20-30 seconds and then muffle. no sense.

The idle speed began to disappear, at first I did not understand what was the matter, and later I remembered that it was necessary to add a lot of idle speed, I added it on a hot engine, it seemed to work out. I come to the dacha in a week, I need to cut a couple of logs, start a saw and at first on a cool motor the chain spins later everything goes away, I stood for about 10 minutes I start everything normally only on a cool motor. This is normal?

If the chain turns, it means that the speed is too high. It should be understood that a normally adjusted and serviceable motor is completely likely to have a slightly overestimated idle speed immediately after starting before warming up. And it can be raised decently. before the rotation of the chain. With the engine warming up, the idle speed is gradually lowered. For this reason, it is recommended to adjust the idle speed only when the engine is warm.

Is it possible to put a clutch drum with a removable rim on a STIHL MS 180 chainsaw (“modernization” of the drum is allowed), for example, from the 250th.

Your STIHL 180 chainsaw won’t start? Prerequisites and solution!

Today, the manufacturer STIHL occupies a leading place among other companies that create the production of equipment designed for agricultural and construction work. The products of this manufacturer are famous not only for their highest level of properties, but also for the good price policy and power of its models. How to make an esr meter how to make a band saw on a STIHL 180 chainsaw your own. It is one of the most recognizable global companies.

Surely, it is quite difficult to meet a person who does not have a chainsaw of this brand. But the fact that out of 10 probable 6 people definitely have them. And that’s not overwhelming, because STIHL chainsaws are as powerful as their sleek design. But unfortunately, such giants of technology fail from time to time and require some kind of repair. Now we will pay attention to one of the moles of this manufacturer, and specifically the STIHL 180 chainsaw. Read about the STIHL ms 660 chainsaw here. So let’s get started.

2 diagram of a standard mechanism. how to start the saw correctly

The ignition is switched on. To do this, you need to move the toggle switch to the desired place or move the switch.
The swap primer usually has to be pressed more than twice. Gasoline is poured into it, after which you will have to press the device more than three times. Sometimes the chainsaw is not equipped with a primer, then you can skip this step.

The adjustment lever, which is responsible for the location of the damper, must be pulled out as far as it will go. Many chainsaws have the ability to block this element. Then it can only be moved while pressing and holding the throttle button. Some chainsaws do not have this lock, which makes them more comfortable to use. In these models, gas may not be fixed or retained when using automatic technologies.

You need to take the starter handle and jerk it with sharp movements until the ignition is heard. It is celebrated by the institution and the almost instantaneous shutdown of the motor. After that, the shutter must be pushed into its original position, checking it until it stops. Then the starter handle jerks again until the device starts. Before carrying out this event, you need to make sure that it is this method that will help the chainsaw start. Some devices have a different ignition system. In order for the motor to work in them, you need to move the damper only by 50%, and only when the motor starts to work fully.

If you purchased a model with a locking gas, you need to prepare in advance for the highest engine speed immediately after activating the device. When there is no fixation, the initial power is very low, so in most cases it has to be increased. If you do not take any action, then in the latter case, the saw runs for a short period of time, and then automatically stalls. If such a situation occurs, you need to start the chainsaw again.

When the device stalls constantly, you need to systematically start it up again (see what to do when the chainsaw stalls when you press the gas). After a while, the motor will pick up speed and be able to maintain active work without interruption.

Saw installation with decompression valve

Users sometimes ask how to launch when the instrument has a decompression valve. There is none on the 250 model. As soon as the first flash occurs, the valve will be in normal operation. The engine control lever will be set when the choke is open. Start-up will continue and the decompression valve must be pressed again. It does not make the start-up fast, but it simplifies the process and makes it comfortable, because during the start-up the operator will have to put less effort.

If you are not entirely sure that you know how to start a STIHL 180 chainsaw, then remember that equipment with a valve, regardless of whether it has a hot or cold engine, must be started using the valve. This will help ease the effort to crank the engine. So you can extend the life of the starter and reduce the number of torn laces, because these chainsaws have a larger cylinder volume and compression.

How to start a STIHL chainsaw: starting process and overview

All STIHL chainsaws have two-stroke engines. Their cold start is carried out according to a similar algorithm. However, on sale you can find models on which there is additional equipment, with its help you can start the saw without much effort. For this reason, the starting method may differ.

Tips for starting a saw MS 180 C

This device, in comparison with the previous one, has some differences in the trigger mechanism. However, there will be no changes in the startup algorithm. The equipment described has a system that uses a spring in the saw starter to reduce the resistance of the motor.

Setting up the saw after winter

Before storing it, you should drain the fuel, and then start the engine and burn off the fuel that remains in the system. Preparation is necessary so that the membranes do not stick together during storage. This simple operation will allow you to start the saw after winter. If you still do not know how to properly start the STIHL 180 chainsaw, then you should know that it will be easier to do this if you add 2 ml of fuel mixture to the cylinder through the plug hole before starting. This can be done with a syringe.

STIHL 250 chainsaw review

You can buy the 250 model at a price of 29,542 rubles. This equipment is a semi-professional model with a 40 cm tire. Power is 3.1 liters. from. or 2.3 kW. Fuel tank capacity is 0.47 l.

Quite often, consumers are wondering how to start a STIHL 250 chainsaw before buying. This was discussed above. However, this information is not the only one that should be read before using the model. Among other features, it should be highlighted:

single-lever control;
the presence of a compensator;
anti-vibration system;
side chain tensioner.

By purchasing this model, you will be able to carry out its quick refueling. This feature is realized by the lid, which has a patented design. The operator, when working with the equipment, will have reliable hand protection. Consumers especially highlight the notch bumper, as well as the chain, which guarantees high-quality and fast cutting of wood.

We start the saw brand MS 211 C-BE

If you, too, were among those consumers who thought about the question of how to start a STIHL chainsaw, then as an example, consider another model that was mentioned above. In it, the feed system is equipped with a hand pump, which makes it easier to start the saw on a cold.

The instruction contains an additional paragraph, which indicates that before starting with the pump, it is necessary to pump fuel into the carburetor. Next, you should proceed according to the principle that was described for the 180 model.

Algorithm for setting the saw “STIHL 180

If you are faced with the question of how to start a STIHL chainsaw, then this process can be considered using the model 180 as an example. In order to carry out work on a cold one, you must turn on the ignition and set the engine control lever to the lower position. In this case, the carburetor flap will block the air from the filter, and the throttle will be open, so the fuel mixture will be enriched.

The starter handle must be pulled several times until the first flash occurs. This will indicate that the mixture has entered the cylinder and the equipment is ready for institution. Before starting the STIHL chainsaw, you must move the control lever up one position. In this case, the air damper will open, while the throttle will remain in the same position.

The starter must be pulled and started. The tool will run at increased speed and the throttle valve will be open. To set the latter in idle speed, you must use the gas trigger and release it. In this case, the tool should start working normally. On the described model of the chainsaw there are no additional devices that would make it easier to start.

Chainsaw MC 180 review

This model of equipment costs 11,490 rubles. It is a household tool that will help you cope with work at a summer cottage. With the help of the machine, you can get rid of unnecessary twigs and cut down small trees. The control is single-lever, and due to its low weight, it is very comfortable to work with the unit.

The consumer should be aware not only of how to start the STIHL ms 180 chainsaw, but also of the technical characteristics. Among others, the 35-cm tire should be distinguished, as well as the engine, the volume of which is 31.8 cm 3. The volume of the oil tank is 0.15 liters. The equipment weighs 3.9 kg. The power of the model is 2 liters. from. Fuel tank capacity is 0.25 l.

2 diagram of a standard mechanism. how to start the saw correctly

The ignition is switched on. To do this, you need to move the toggle switch to the desired place or move the switch.
The swap primer usually has to be pressed more than twice. Gasoline is poured into it, after which you will have to press the device more than three times. Sometimes the chainsaw is not equipped with a primer, then you can skip this step.

Tips & Tricks

In order for there to be no problems with the chainsaw and it worked without breakdowns, you should follow the operating rules:

Compliance with safety rules.
Running-in after purchase.
Check chip thickness regularly. If it is small, then you need to sharpen the chain. If the chain is sharp, the chip thickness is approximately 3-4 mm.
Can’t cut with the end of the bar.
It is advisable to replace parts of the same manufacturer as the saw model.
If you are new to sawing, train on low speed models.

What to do if your chainsaw won’t start?

There are many factors why a chainsaw will not start when the starting technology is followed. The most common causes and remedies are:

there is no spark on the spark plug. replacement or drying is required if water gets in;
a problem with the supply of gasoline to the filter. blowing through the fuel hose or filter, replacing;
clogged fuel or air filter. high-quality cleaning is needed.

If these simple tips don’t help, a complete diagnosis of the problem is needed. It is recommended to take the chainsaw to a service center, where they can check the compression of the cylinder and crankcase, as well as the operation of the carburetor.

Starting your chainsaw correctly will ensure that this tool works consistently and reliably. At the start, before starting sawing, you should properly prepare and fill the fuel mixture, adjust the main structural elements. It is important to take into account the weather conditions, as well as the features of a particular model.

Chainsaw Husqvarna 235

engine power is 1.7 liters. from;
the chain got a size of 30 cm;
fuel tank. 300 ml;
oil tank. 200 ml;
weight. 3.5 kg.

What happens at the moment of priming fuel with primer, and how it helps to start the saw more efficiently?

There is no need to use a primer on a hot chainsaw, since there is enough fuel in the carburetor to start.

Chainsaw Husqvarna T435

power is 1.5 kW;
the chain is 35 cm long;
rotation speed. 19.1 m / s;
weight. 3 kg.

Chainsaw oil selection

Especially it is necessary to pay attention to the choice of oil, the operation of the entire tool depends on it. The higher its quality, the longer and more efficiently the chainsaw will serve. You need to buy a special oil that is made specifically for such engines. If the wrong lubricant is used, common problems will be:

Engine breakdowns;
Ignition problems;
The chainsaw will stall, and sometimes just refuse to start;
Saw overheating.

Different parts require different lubricants. one oil will not work for all applications. The choice of this material is one of the most important things when interacting with a chainsaw. The lifespan of the instrument depends on the decision made.

Special lubricants have been created for Foresta saws and the motor oil is perfect for protecting the “heart” of the tool. The chain lubricant is not suitable for the motor, otherwise the tool life may be reduced. Even if the oil is of high quality, but it is not used for its intended purpose, nothing good will come of it.

Foresta saws are specially designed with proprietary lubricants that make working with them easier and additionally protect against overheating.

Getting STIHL MS C-BE

The fuel supply system in the STIHL MS 211 C-BE chainsaw is additionally equipped with a manual fuel pump, which makes it easier to start the chainsaw on a cold.

The instruction for starting this model of the STIHL chainsaw contains one additional point, which is that before starting the chainsaw on a cold one, it is necessary to pump fuel into the carburetor using a pump. Further, the instruction does not differ from starting STIHL 180 and follows the same algorithm.

Sources:

http://crast.ru/instrumenty/kak-zavesti-pilu-shtil-video
http://fb.ru/article/330854/kak-zavodit-benzopilu-shtil-protsess-zapuska-i-obzor
http://metallvsegda.ru/instrumenty/kak-pravilno-zavesti-benzopilu-instruktsiya-dlya-pili-shtil.html

Chainsaws chainsaw, correctly, start, stihl