How to store a benzotrimer and a chainsaw in winter. Preparation of a mowing coil with…

31st October 2022

Overwinter: how to prepare a gas technician for storage

Before putting a garden and surgery for winter storage, you need to carefully prepare it-to preserve it. The more difficult the device, the more attention it will require. We have compiled you the optimal conservation algorithm for you. At the end of the season, the “heavy” garden equipment goes for storage until the next spring. Often it is simply driven into the barn or closed in the house, slightly wiping with a rag. If you have not prepared the technique for wintering, in the spring it may not start, because it is simple in the conditions of a change in temperature and humidity modes. a serious test for mechanisms. This applies to a greater extent to the gas instrument, it must be treated especially carefully. And although comprehensive recommendations are usually given in the operation manual, we recall the basic rules for storing garden equipment.

Any tool, regardless of the type and purpose, before laying on storage, you need to wash, dry and inspect the details for wear and replacement. There is nothing worse than moisture that fell into mobile or vulnerable details and mechanisms. Freezing in an unheated room, it turns into ice and damages the elements of the system. It is also advisable to drain gas tank gasoline for fire safety reasons. But for the clock, other recommendations. the equipment cannot be left “dry”, so the oil is not removed for the winter, but they are changed.

When stored, fold the equipment as indicated in the operating manual

The cutting parts (such as lawnmand knives) should be sharpened, and hinged joints should be cleaned of dust and dirt and grease. Check the condition of the fasteners and power cord of the power tool, if necessary, replace them without leaving until spring. Next, we consider each type of technique and the requirements for its conservation in more detail.

Fuel drain

If you store fuel for more than 30 days, it will lose its properties. Before sending a lawn mower to winter storage, it is best to drain all fuel from the fuel tank. Also, the remains should be developed. Make a device, let it work for several minutes. As soon as the remnants of gasoline from the carburetor are developed, the lawn mower will stall.

Want to leave fuel in the tank? In this case, be sure to use special stabilizers. The tool is added to the tank, thoroughly stirred. It is important to observe proportions. The tank needs to be filled to the neck.

The concept of long.term storage of a chainsaw

The main goal of conservation of absolutely any equipment is to prevent the development of parts and mechanisms of negative processes on the working surfaces. The negative processes include:

Corrosion
Dehydration/getting wet
Precipitation and evaporation of liquids
Dusting
Coropulmonary from temperature drops

To store mothballed equipment, you should choose a place with optimal microclimate conditions. For long.term storage of a chain saw tool, a garage is ideal. In this case, good ventilation should be provided in the room. The garage must be dry and, if possible, insulated.

Regarding heating, yes, for long.term storage you need a warm and dry place. But since the heating of the room is purely for storing tools of tools is irrational, it is better to refuse constant heating. In this case, the situation may save periodic heating of the garage.

Even if heating, heating will be stimulated and accelerated by the evaporation of excess moisture, which the container of mothballed technology warms up.

Preparation for storage and conservation of a chain saw tool

If the chainsaw is planned to be stored for a long time, it must be disassembled, cleaned, washed and dry for. But preliminary from saw technique you need to drain all gasoline. To empty the fuel, you should start a chainsaw with an empty fuel tank. After a few seconds, the saw motor itself will stall in itself.

Additionally, the engine lubrication system should also be lowered. During the winter period, the existing oil will still deteriorate. The fact is that any motor lubricant contains additives (friction modifiers, antioxidants, etc.). With a long stagnation, especially if low temperature, the additives are deactivated and precipitated.

The chainsaw is versed in the following order:

Disconnect the tire and remove the chain. The tire and chain should be cleaned from blockages. You can even rinse them in kerosene and dry well. If the chain managed to swell after the last sharpening, then it is advisable to correct the tip of the chain. Of course, you can leave this work in the spring.

The chain tire must be covered with a thin layer of preservative. Suitable movil or cannon fowdered. That is, you need to drop a little preservative on a rag and grind the spare parts for them. The tire with a chain should be stored in oiled paper, best of the parchment. But just ordinary rags are suitable.

We extract filter elements from the chainsaw. It is necessary to extract coarse cleaning filters from the fuel tank and the neck of the lubricant system. Cricking filters are simply washed and dried. If a filter of fine fuel is provided, then it is best to simply replace it with a completely new analogue in the spring.

Special attention should be paid to the air filter. The airfall filtration element must be disconnected and cleaned well. If the filter has already worked for 2-3 seasons, then it makes sense to just put in the spring a new element of air filtration.

We unscrew the spark plug and clean the candle head, especially the electrode, from the carbon. The user must track the service life of the candle. Subject to intensive operation of the chain saw, the candle usually works out 2-3 seasons. If the chainsaws are rarely used, then the candles are enough for an average of 4-5 seasons.

If good performance is expected from the chainsaw, then the spark plug should be changed every 2 years!

Add 5 (ml) of motor oil to the candle well and scroll the crankshaft 2-3 revolutions. You can scroll the crankshaft by the asterisk of the chain. This technique will allow motor lubrication to create a thin protective layer in the cylinder.

As mentioned above, the lubricant has the ability to drive and dry with stagnation. It is for this reason that the user needs to manually scroll the cranks of the chain saw with a frequency of 1 time per month. If the user obviously knows that he will not have time or opportunity to regularly develop a power unit, then it is better not to fill the oil in the cylinder.

Do not forget to screw back the pre.cleaned spark plug!

Clean and lubricate the chain tensioner.
We pack all the disconnected parts and the power unit itself. To increase safety, it is better to store a saw tool in a strong cardboard box. You do not need to make a container container, since moisture can accumulate without air exchange in the box.

How to work with a chainsaw in the winter period

The need for a chainsaw may arise in winter. In this case, the user needs to know how to make the work of a saw chain tool as reliable and safe as possible.

The main catch during the operation of the chainsaw in winter lies in the low ambient temperature. In the cold, gasoline becomes less volatile, which affects the work of the carburetor. To start a chainsaw and warm up the engine to the conditioning temperature, very often you need to use a forced fuel suction.

Who does not know, with a manual fuel suction, candles are filled with gasoline. In this case, the candles quickly become overgrown with soot, they need to be cleaned almost after each use.

Chainsaw Winter vs Summer Mode (Echo Examples)

It is necessary to be prepared to the fact that the lubricant system will not work 100% effectively. Oil for chain saws thickens in the cold. To prevent an increase in viscosity, a small portion of gasoline should be added to the oil.

After the entire front of the work, the chainsaw should be preserved for storage according to the above scheme.

Do I need to preserve an electric chain saw in winter

Chainsaws differ from electric chain saws only by the type of drive system. The electric saws were a little more lucky, because they do not use liquid fuel, they have no spark plugs, no filters, no carburetor. But electric saws need conservation for the winter. Of course, for electric saws, a simplified preparation scheme for storage is provided.

You just need to disconnect the tire with a chain, beveled from and grease with a preservative. Everything is as in the case of gasoline analogues. If the chain managed to swell, we correct the sharp edges on the teeth.

Additionally, the chain tensioner should be cleaned and lubricated. Oil from the lubrication system must be drained. In the spring you will need to fill the system with new fresh oil.

General rules for conservation of technology

At least a tool, regardless of the type and purpose, before laying on storage, it is necessary to wash, dry and look around the details for wear and substitution. There is nothing worse than the water that fell into mobile or vulnerable details and mechanisms. Freezing in an unheated room, it is converted into ice and damages the elements of the system. It is better to drain gas tank gasoline from fire safety judgments. But other tips are closed. the equipment cannot be left “dry”, because the oil is not removed for the winter, but they are changed.

When stored, fold the equipment because it is indicated in the operating manual

The cutting parts (such as lactes of the lawn mower) should be sharpened, and hinged joints should be cleaned of dust and dirt and grease. Check the condition of the fasteners and power cord of the power tool, as needed, change them without leaving until spring. Next, we see each type of technique and the requirements for its conservation in more detail.

This is perhaps one of the few tools for which there is work in the cool season. True, the spectrum of operating temperatures of the chainsaw is usually small due to the fact that it contains insistent parts, gas and oil. If the manufacturer guarantees the operation of the tool at a temperature of –10 ° C is a very good indicator, and such a saw can be used almost all year round. If you leave the summer cottage forever, then patting the appropriate conservation.

“Header” at least some chainsaw is a single.cylinder two.stroke carburetor engine. Another principle element is a chain. Specifically, most of the conservation tips are devoted to the care of these 2 elements:

First drain the remnants of fuel from the tank, carburetor and oil for lubrication of the chain. For the full production of fuel, you can start the chainsaw of an idle and wait until the gasoline is completed. Then wipe the gas tank dry so that he does not start rusting. This is an option for long.term conservation, at least 3 months. But there is also the 2nd option for those who are falling the forest or carrying out other work in winter. In this case, the tank is recommended to be filled with high.quality gasoline to the edges and leave for storage in this state. If you urgently come in handy for you to cut down a tree. excellent, you have a completely finished technique under your hand. But remember, gasoline, which after 2-3 frosty winter weeks will begin to remember the jelly by the mixture, even a high-class motor can disable;
Using a wire probe or a home-made nozzle, remove filter-endor filters from the fuel and oil tanks. Wash them and set them back after drying or, if necessary, change to new. Do the same with an air filter;
Remove the saw chain and tire and clean them of the remains of sawdust, wood dust and dirt;
Remove the clutch cover, painstaking it under a stream of warm water and let it dry. Lubricate the worm gear and screw of the side tension system of the chain;
Remove the spark plug and clean it from soot and fuel residues. Pour 5-7 ml of motor oil into the candle hole and crancele the motor for 3-4 revolutions so that the oil is distributed according to the connecting rod mechanisms and the cylinder-piston group. Leave the piston at the top (in the raised state). After that, set the candle in place, but do not put on the ignition terminal;
Cover the saw tire and chain with protective lubricant and store wrapped in a piece of paper or fabric impregnated with oil;
pack the tool and hide the removed parts into a dry, dark and nonsense place.

How to store a chainsaw in winter

This is perhaps one of the few tools for which there is work in the cold season. True, the range of operating temperatures of the chainsaw is usually small due to the fact that it contains insistent parts, gas and oil. If the manufacturer guarantees the operation of the tool at a temperature of –10 ° C is a very good indicator, and such a saw can be used almost all year round. If you leave the summer cottage for a long time, then take care of proper conservation.

The “heart” of any chainsaw is a single.cylinder two.stroke carburetor engine. Another important element is the chain. It is the care of these two elements that most of the recommendations for conservation are devoted to:

First of all, drain the remains of fuel from the tank, carburetor and oil for lubrication of the chain. For full production of fuel, you can start the chainsaw of an idle and wait until the gasoline is over. After that, wipe the gas tank dry so that it does not begin to rust. This is an option for prolonged conservation, at least 3 months. But there is a second option for those who are falling the forest or carrying out other works in winter. In this case, the tank is advised to fill with high.quality gasoline to the edges and leave for storage in this state. If you urgently need to cut down a tree. excellent, you have a completely finished technique at hand. But remember, gasoline, which after 2-3 frosty winter weeks in consistency will begin to resemble jelly, can even be disable; even a first-class motor;
Using a wire probe or homemade nozzle, remove filter-endor filters from the fuel and oil tanks. Rinse them and set them back after drying or, if necessary, replace with new. Do the same with an air filter;
Remove the saw chain and tire and clean them of the remains of sawdust, wood and dirt;
Remove the clutch cover, thoroughly rinse it under a stream of warm water and let it dry. Lubricate the worm gear and screw of the side tension system of the chain;
Remove the spark plug and clean it from soot and fuel residues. Pour 5-7 ml of motor oil into the candle hole and cranceize the engine for 3-4 revolutions so that the oil is distributed according to the connecting rod mechanisms and the cylinder-piston group. Leave the piston at the top (in the raised state). After that, set the candle in place, but do not put on the ignition terminal;
Cover the saw tire and chain with protective lubricant and store wrapped in a piece of paper or fabric impregnated with oil;
pack the tool and hide the removed parts into a dry, dark and nonsense place.

About once a month, perform the crankshaft to update the lubricant on the connecting rods and in the cylinders with the pistons.

If you have an electric drain, then all you need to conservation is to lubricate the saw tire and chain with protective grease.

Where to store: options and necessary conditions

Sarai or equipped housekeeping block is on the house territory of almost every summer resident. These storage places are the most common. The main conditions for storage of gas technicics in sheds or utility rooms are low humidity and stable temperature without sharp jumps.If the room is insulated, it will be an additional plus.

Another place for storing benzotechnics is a garage. Do not place the equipment close to the car, and also, by suspending it, you need to make sure that in the event of a fall it will not touch the car.

This method is not very popular in the countries of the post.Soviet space. But if there are no other options, find the company that provides these services is possible.

What you should pay attention to:

General rules for conservation of technology

When stored, fold the equipment because it is indicated in the operating manual

This is perhaps one of the few tools for which there is work in the cool season. True, the spectrum of operating temperatures of the chainsaw is usually small due to the fact that it contains insistent parts, gas and oil. If the manufacturer guarantees the operation of the tool at a temperature of –10 ° C is a very good indicator, and such a saw can be used almost all year round. If you leave the summer cottage forever, then patting the appropriate conservation.

First drain the remnants of fuel from the tank, carburetor and oil for lubrication of the chain. For the full production of fuel, you can start the chainsaw of an idle and wait until the gasoline is completed. Then wipe the gas tank dry so that he does not start rusting. This is an option for long.term conservation, at least 3 months. But there is also the 2nd option for those who are falling the forest or carrying out other work in winter. In this case, the tank is recommended to be filled with high.quality gasoline to the edges and leave for storage in this state. If you urgently come in handy for you to cut down a tree. excellent, you have a completely finished technique under your hand. But remember, gasoline, which after 2-3 frosty winter weeks will begin to remember the jelly by the mixture, even a high-class motor can disable;
Using a wire probe or a home-made nozzle, remove filter-endor filters from the fuel and oil tanks. Wash them and set them back after drying or, if necessary, change to new. Do the same with an air filter;
Remove the saw chain and tire and clean them of the remains of sawdust, wood dust and dirt;
Remove the clutch cover, painstaking it under a stream of warm water and let it dry. Lubricate the worm gear and screw of the side tension system of the chain;
Remove the spark plug and clean it from soot and fuel residues. Pour 5-7 ml of motor oil into the candle hole and crancele the motor for 3-4 revolutions so that the oil is distributed according to the connecting rod mechanisms and the cylinder-piston group. Leave the piston at the top (in the raised state). After that, set the candle in place, but do not put on the ignition terminal;
Cover the saw tire and chain with protective lubricant and store wrapped in a piece of paper or fabric impregnated with oil;
pack the tool and hide the removed parts into a dry, dark and nonsense place.

Sprayers

Hoses, pistols for irrigation, droppers and other inventory for irrigation must be free from water residues. Ordinary hoses should not be left on the street: at minus temperatures, water will turn into ice. so the hose can become unusable. To preserve sprayers for the winter, you need:

inspect all the mechanisms and check if there are tights of hoses, cliffs and damage to the spray houses;

Check the quality of the oil: it should not contain extraneous fluids and impurities;

Clean or replace all filters with new ones. in the houses of sprayers, pressure and absorbing.

For the winter, sprayers should be brought into a dry warm room.

Where is it better to store a lawn mower?

During the spring and summer season, the mowing of grass and weeds is carried out several times, and the maintenance of grass is to clean the parts of the parts and change gasoline and oil.

When the season of using this tool goes, it comes to think where it is better to store the lawn mower, so that after the winter it is in the same good condition, does not neighing and does not require repairs!

In order for your unit, which is a modern and complex, and as a rule, not a cheap device, and after the winter it was whole in working condition, you first need to study the instructions for the operation and maintenance of the acquired lawn mower, which must also have a rule Storage of the lawn mower.

From compliance with the rules of use, proper maintenance, timely prevention and repair, using only original spare parts, and proper storage, the quality work and performance of your lawn mower depends.

Useful tips

To avoid premature failure of a trimmer for grass, follow the following recommendations:

What documents to look for? To arrange a garage according to an amnesty will help:-any decision of the authority (including Soviet times), confirming that you were once provided for a plot for a garageany decision of the plant, factory, collective farm, state farm or some other enterprise (which organized the garage cooperative) with the same meaning.

This can be done in the same way that you transferred to the documents. Or order it yourself through the portal what else needs to be done? The last stage remained. to issue the ownership of the garage and the land under it. For this you return to the local administration, that is, your municipality.

Proper storage of a benzotrimer (motorcycles, lawn mowers)

Sooner or later, the season ends, trimmers for grass and other equipment go to long.term storage to the far corner. In order to use the tool next year without problems, it is necessary to perform several simple manipulations, so to speak, to preserve a gasoline trimmer for grass.

And storage in a room with constant temperature and normalized humidity will help to save some bearings. Lubrication and cleaning of some elements are also necessary. For storage, it is better to use heated rooms: warm garage, pantry or insulated balcony.

Preparation of a chainsaw for long.term storage in the video

In the winter period, many garden tools (for example, a chainsaw, a lawn mower) have no need, so they should be properly prepared for long.term storage so that the performance of the tool does not decrease. If necessary, it is recommended to contact specialists and conduct full maintenance. However, in most cases, there will be enough independent preparation for wintering.

The first thing to do is to do it immediately after the completion of the work, the chainsaw or motorcycles drain fuel from the tank into specially intended containers. After the tools, you should give a job at idle so that the remaining fluids from the carburetor will leave. If this is not done, the fuel that remains in the system over time to delay, as a result of which tarry deposits are formed. In the future, they will impede the normal functioning of the chainsaw or motorcycle. When the engine stalls, the tank must be left open for a while for complete drying.

The next stage is a washing of tools. Warm water (you can add powder or detergent) and a brush or rag you need to wipe the steering wheel, rods and protection. You should also partially disassemble the motor, rinse some of its parts, as well as clean the air filter.

It is necessary to lubricate the moving parts. A lawn mowing knife should also be removed and cleaned by the hill cartridge. A lubricant is added to the gearbox, and the accurate adjustment of the carburetor is also made. The lawn mower is completely inspected for the presence of scuffs, distortions, cracks. If necessary, the details are replaced.

As for the chainsaw. you should remove and clean the cutting tool. Wipe the tool with a damp cloth to clean it from contamination. The chainsaw is also checked for any damage. A remedy for corrosion is applied to the metal parts.

To lubricate the virgin piston parts of the motorcycles, it is necessary to unscrew the spark plug, bring the piston to the upper point, and pour a small amount of motor oil into the candle hole. After that, you need to handle the crankshaft several times by the starter. The lighting candle of the lawn mower is put in place, but at the same time it is not much delayed. It is advisable to update the lubricant in the cylinder at least once a month in the winter period. It is enough to remove the candle and make a few turns of the crankshaft.

How to store chainsaws or motorcycles.

Motokos/chainsaw engine should be wrapped in dense fabric so that the condensate does not get inside during temperature changes. Store tools in dry and warm room. It is better to hang a motorcycle, and the chainsaw can be stored in a horizontal position, but by always dressing a protective cover (if any) or put in a box.

They are powerful and productive garden units that are used to mow grass, weeds of varying degrees of stiffness and young branches of trees and shrubs. These tools are able to make life very easier for the owners of country houses and cottages, in a short time and with slight efforts to simply and quickly improve the lawn, garden and personal plot, garden. What could not have been done using a regular braid for grass.

Regardless of which manufacturing company produced the lawn mower that you acquire, on the proper care of it, and the same storage, and its service life depends.

How to preserve a chainsaw for the winter

Chainsaws. a tool that, unlike many, can be used in winter. At extremely low temperatures, it is not worth using it, but for high.quality chainsaws, the threshold is minus ten degrees.

If you do not plan to use the tool in winter, you should take care of its quality storage, because it has not stable elements for cold.

If in winter you plan to use a saw, then it should be stored with a tanger filled with gasoline (gasoline should be of high quality). The main thing is to remember that after a couple of weeks of persistent frosts, gasoline in the tank will thicken and the use of a saw in this state can disable it. Store the tool in this case is in a warm room.

If you leave a chainsaw for a long wintering, the stages of preparation should be as follows:

It is necessary to clean the tank from fuel. This can be done by draining it, either by starting the work of the saw until full production. Next, to prevent the appearance of rust, the tank must be wiped dry.
Filters from fuel and oil tanks need to be removed, cleaned and dried or replaced with new ones, if necessary. A similar operation with an air filter.
The chain needs to be cleaned from the remaining waste of saw. After the chain, you need to lubricate and wrap the elements into the fabric, which was previously impregnated with oil. We store the details separately.
Store a saw in a dark room without dust and with low humidity.

The main details that need to be paid attention to in preparation for winter conservation. the engine and chain.

Preparation of a chainsaw for long.term storage in the video

If you do not want to have problems with the launch of the lawn mower in the spring and that the equipment serves for many years, you need to produce several not difficult, but necessary procedures.

Consistent lubricant (you can use lilet).

Shplitz for filling the lubricant (if your lawn mower is equipped with special stains).

And, of course, half an hour. an hour of free time.

You can easily purchase all devices and lubricants in any spare parts store.

Wipe the body of the lawn mower with a damp cloth. Especially pay attention to the working surface of the “Snail”. When examining the “Snails”, set the lawn mower to the maintenance position, for this, unscrew the handles and put the lawn mushroom vertically so that the oil in the crankcase does not flow, see. picture. Remove excess grass and dirt from the working parts of the belt drive if your lawn mower is equipped. It is not recommended to wash the lawn mower with water from the hose and a high.pressure washing, since water can get into the filter elements of the engine, and the abrasive under pressure can get into the bearings and rubbing parts of the lawn mower.

It is not recommended to store fuel for more than 30 days, for this it is better to drain all gasoline for the winter, or use a special fuel stabilizer. It is necessary to drain the remaining gasoline from the gas tank, then make the lawn mower so that the remaining fuel in the carburetor is developed. If you use the fuel stabilizer, then it is necessary to store the lawn mower outside the season with a full gas tank.

Clean or replace the air filter and a preliminary fuel filter (if the engine on your lawn mower is equipped with it).

To prevent corrosion, the combustion chamber must be twisted and pour a teaspoon of oil into the chamber. Then, several times, without jerks, pull the starter handle so that the oil would be evenly distributed in the chamber. After you need to pull the starter’s rope until the resistance appears so that the valves are closed, this will additionally protect the combustion chamber from corrosion.

It is necessary to lubricate with consistent lubricant wheels and bearings bearings (if present).

If your lawn mower is equipped with special oils, it is necessary to fill a lubricant into them using a special syringe.

If your lawn mower is equipped with an electric launch, then it is necessary to completely charge the battery.

Check all the cables of the lawmaker drive. If they have a double device (core and braid for cm. drawing), then it is necessary to lubricate the core of the cable with liquid oil (the engine oil is quite suitable).

For storing lawn mowers in winter, room temperature is best suited. But if you do not have such an opportunity, then you should store the lawn mower in the winter in a dry, well.ventilated place.

If you have observed all points during conservation, then your summer friend will serve for many years without breakdowns and at the beginning of the season there will be no problems with launching.

If you still need to repair the lawn mower. or in front of the winter season, repairing snowbrushes. You can always count on our specialists.

As for the chainsaw. you should remove and clean the cutting tool. Wipe the tool with a damp cloth to clean it from contamination. The chainsaw is also checked for any damage. A remedy for corrosion is applied to the metal parts.

How to store chainsaws or motorcycles.

20” bar on a custom Stihl ms200t

Operation of chainsaws in the cold season: the main points

There is always a task in the household for chainsaws, so sending it to the “winter vacation” is not always rational. In such cases, the conservation of the tool is not carried out in full, t.e. Without complete disassembly.

The cold makes it difficult to launch gasoline engines: the fuel evaporates poorly, so if you open the air damper, the chainsaws or it will not be started at all after the first clocks, or it will stupid immediately. As a result, it will have to warm and start on the suction, as a result of which there is a risk of filling the candle with gasoline. All this takes too much time and leads to clogging and reducing the service life of individual tools.

If you plan to work as a chainsaw in the winter season, store it, and, in particular, the fuel mixture, should be in a well.ventilated, dry and warm, in extreme cases of an unheated room protected from external atmospheric effects.

Before starting work, you should make sure that the fuel has sufficient temperature for fire, and the oil in the lubrication system of the tool is normal viscosity. Separate models of the chainsaws are equipped with a hot air supply system to the carburetor from the cilia of the cylinder cooling, which reduces the risk of freezing of the air filter and prevents the formation of condensate on the carburetor itself.

Run the saw in the cold with a closed throttle, after checking the quality of the lubricant and the stretch of the chain. After completing the work, you cannot immediately enter the tool into the room. This is guaranteed to lead to the appearance of condensate, which is why you will have to remove it, disassemble and clean it.

So that the oil does not thicken in the cold, it must be diluted a little with gasoline. This will ensure uniform lubrication and stability of the chain tension.

Rosopil’s rehabilitation: main points

With the onset of spring, much more work appears in the household than in the winter season. This means that the time has come for a chainsaw. it needs to be re.registered and prepared for the beginning of work. The procedure will be as follows:

With prolonged storage, the fuel mixture loses its qualities, so this should not be used. This can lead to various troubles, starting from the loss of engine power and ending with the contamination of the carburetor channels and the fuel supply system.

Sharpening of the saw chain in the photo

As in the case of the commissioning of new chainsaws, the saw set of the tool removed from the conservation is important to adjust correctly. The chain should not bite the material and move with jerks. If it is pulled, thimes will be carried out with difficulty, if weakened. significant vibrations and beating arise when cutting. You can determine the degree of tension by taking the chain by the tooth in the area of the end of the tire and pulling it out. With proper adjustment of about a third of the shank, it will remain in the groove of the saw tire, and the chain itself will move freely.

Some models of chainsaws are equipped with a system of automatic adjustment of the chain tension. However, in this case, the quality of the installation of the chain headset always needs to be checked what is called visually and manually.

Only the correct attitude to the tool can ensure its normal operation and long service life. Do not forget to put your chainsaw on winter conservation and perform all the necessary actions to launch it into work with the onset of spring-and it will last you as long as possible, without delivering any trouble.

Sources:

https://drillzone.ru/dlya-strojki/kak-hranit-motokosu.html
https://2lzz.ru/sovety/kak-podgotovit-benzopilu-k-zime-poleznaya-informatsiya-sovety-spetsialistov
https://101benzopila.ru/kak-hranit-benzopilu-zimoj-tehnologia-konservacii-sovety-i-rekomendacii/
https://weldingmaterials.ru/drugoe/kak-hranit-benzopilu.html
https://101benzopila.ru/kak-hranit-benzinovyj-trimmer/
https://garage-yourself.ru/kak-hranit-trimmer-benzinovyy-v-garazhe/
https://101benzopila.ru/mozno-li-hranit-trimmer-v-vertikalnom-polozenii/
https://masters-tut.ru/uhod-za-trimmerom-zimoi-i-podgotovka-trimmera-k-vesne-pravilo-hraneniya/
https://shashlichnii-dvorik.ru/hranenie-produkty-i-napitki/kak-pravilno-hranit-benzinovyj-trimmer-zimoj.html

Grass Trimmer benzotrimer, chainsaw, store, winter